The main stack size was too small for this sample application
when TLS was enabled. Increasing it to 1504 bytes.
Fixes#7269
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add hardware dependencies and filters to make sure we do not explode if
for example we try to build a sample/test using rtc when the platform
does not support that.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Payload dump function not adopted to multi fragments CoAP packet. Still
assumes whole payload exists in single packet. Also does not handle all
return cases of coap_packet_get_payload() function, which is causing
coverity failures.
Coverity-CID: 185277
Coverity-CID: 185278
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Update the LwM2M client sample documentation with usage examples
of the newly introduced overlay-*.conf fragments. Remove the
references to prj_dtls.conf.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
The file overlay-bt.conf contains only the needed CONFIG items to
support Bluetooth networking.
For example, DTLS-enabled BLENano2 HW can be supported with the
following build:
cmake -GNinja -DBOARD=nrf52_blenano2 \
-DCONF_FILE="prj.conf overlay-bt.conf overlay-dtls.conf" ..
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Instead of maintaining a nearly identical copy of prj.conf to support
DTLS, let's replace it with an overlay-dtls.conf file containing only
the CONFIG settings needed to support DTLS. This can be used via the
-DCONF_FILE command line argument when configuring the sample:
Non-DTLS-enabled build:
cmake -GNinja -DBOARD=qemu_x86 ..
DTLS-enabled build:
cmake -GNinja -DBOARD=qemu_x86 \
-DCONF_FILE="prj.conf overlay-dtls.conf" ..
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Rework samples using LED and GPIO to enforce use of "CONTROLLER"
as LED and PGIO postifx.
Change impact all samples that could be run by boards yet moved to
GPIO node generations, which is only STM32 for now
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In sample application of COAP there is no need of payload
for GET method & it is only applicable to put
and post methods are modified in coap-client.c
Signed-off-by: Tarun Kumar Agarwal <tarun.kumar.agarwal@intel.com>
- Added example OpenThread projects for KW41Z in echo/server samples
- Added projects to sample.yaml for sanity testing
Signed-off-by: David Leach <david.leach@nxp.com>
Assign special Product ID (0x101) to wpanusb protocol exporting
IEEE802.15.4 over USB.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Remove galileo as the only board to build for and cleanup the filtering.
Also, remove arduino 101 conf, this is not a networking platform we want
to tests.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This application just enables VLAN tag for ethernet interface.
Set CONFIG_SAMPLE_VLAN_TAG option to define the desired VLAN tag.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some of the sanitycheck tests were having too small limit for
network buffers when compiling for sam_e70_xplained board.
Increase the buffer limits when testing this for this board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We can use default values of CONFIG_USB_DEVICE_VID and
CONFIG_USB_DEVICE_PID for sanity check builds.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The final ending chunk was not sent after the request was served.
This caused the remote client to constantly send the same request
to the server.
Fixes#6356
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In sample application of COAP put and post
methods are implemented in coap-server.c
and coap-client.c
Signed-off-by: Tarun Kumar Agarwal <tarun.kumar.agarwal@intel.com>
Combine several generic config file into prj.conf that can be
used by several boards and configurations.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This demostrates how to classify the network traffic when sending
data. The application will create similar functionality as
echo-client so user can use echo-server running in remote host to
test this sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of always allocating both IPv6 and IPv4 address information
to every network interface, allow more fine grained address
configuration. So it is possible to have IPv6 or IPv4 only network
interfaces.
This commit introduces two new config options:
CONFIG_NET_IF_MAX_IPV4_COUNT and CONFIG_NET_IF_MAX_IPV6_COUNT
which tell how many IP address information structs are allocated
statically. At runtime when network interface is setup, it is then
possible to attach this IP address info struct to a specific
network interface. This can save considerable amount of memory
as the IP address information struct can be quite large (depends
on how many IP addresses user configures in the system).
Note that the value of CONFIG_NET_IF_MAX_IPV4_COUNT and
CONFIG_NET_IF_MAX_IPV6_COUNT should reflect the estimated number of
network interfaces in the system. So if if CONFIG_NET_IF_MAX_IPV6_COUNT
is set to 1 and there are two network interfaces that need IPv6
addresses, then the system will not be able to setup IPv6 addresses to
the second network interface in this case. This scenario might be
just fine if the second network interface is IPv4 only. The net_if.c
will print a warning during startup if mismatch about the counts and
the actual number of network interface is detected.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move IP address settings from net_if to separate structs.
This is needed for VLAN support.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
With upcoming ICs that are not in the nRF5x family, rename the flash
driver and all its dependencies from nrf5 to nrf.
Should also fix the issue introduced by f49150cab6 which broke the
assignment of the flash device due to a partial rename.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Network packet cannot be NULL so no need to check its value.
Coverity-CID: 183063
Fixes#6669
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use HAS_ Kconfig option as intended, those are invisible option that
signify support of a certain feature that can be selected by a hardware
or platform.
For RTT and system view this was not dont in an inconsistent way.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This application just enables native host networking and net-shell
which allows connectivity from zephyr to host system via tap device.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of CONFIG_COAP_MBEDTLS_SSL_MAX_CONTENT_LEN, use recently
introduced CONFIG_MBEDTLS_SSL_MAX_CONTENT_LEN.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This value allows to set max payload length of a TLS protocol
message, and passed thru to mbedTLS as MBEDTLS_SSL_MAX_CONTENT_LEN
setting. The only safe value is 16384, which translates to 32KB
of RAM required just for mbedTLS input/output buffers. Any other
value can be configured *only* per a particular application
(e.g. knowing that it won't pass more than spefific amount of
data at once and/or won't connect to a server with a long cert
chain). Previosuly, we had quite an adhoc and inflexible config
with random values for that setting, based on protocol.
Note that while the safe value is 16384, "backward compatible"
default of 1500 is used (good for DTLS on the other hand).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
There are 174 RX/TX net pkt reserved, this make build fail
with some boards due to ram overflow (e.g quark_se_c1000).
Fix this by reducing NET_PKT RX/TX reserve to 100, which
seems fair enough for this use case. Moreover, don't think
there is any reason to have more NET_PKT than NET_BUF.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
This sample application implements a web service that provides
zephyr console over websocket.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is a http(s) server that supports also websocket.
It sends back any data sent to it over a websocket.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
With usb_device support added to nrf52840_pca10056 board, sanity
check script compiles the sample net/wpanusb and it fails with
undefined reference for symbol cc2520_configure_gpios.
First of all cc2520 shouldn't be compiled at all for nrf52840
since it has its own ieee802154 radio. The prj.conf under the
sample samples/net/wpanusb simply hard codes the config
CONFIG_IEEE802154_CC2520=y and is causing the ieee80211_cc2520.c
file to be compiled. If it's removed from the configuration file
we get other errors. So it is not straight forward.
For now, as a workaround, exclude the nrf52840_pca10056 platform
until there's a proper fix.
Signed-off-by: Sundar Subramaniyan <sundar.subramaniyan@gmail.com>
Rename variable zpkt to cpkt to complete the move from ZoAP to CoAP.
Remove unused tests/net/lib/zoap/CMakeLists.txt file.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
net_app_ctx maintains multiple net contexts(net_ctx). But when http
api's wants to reply or send some data, its always choose the first
net_context in the array, which is not correct always.
net_app_get_net_pkt_with_dst() api will select proper context
based on destination address. So with the help of new api in
net_app, http can select proper context and send packets. To
achieve this, desination address is provided in http_recv_cb_t
and http_connect_cb_t callbacks. Also chaged relevant API's to
provide destination address in http message preparation methods.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Initially this sample was intended to be very simple and schematic,
but as this sample going to become a base for stream API conversion,
time to handle all the edge conditions.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Initially this sample was intended to be very simple and schematic,
but as this sample going to become a base for stream API conversion,
time to handle all the edge conditions.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
mbedTLS log level is obviously a mbedTLS config setting. It makes
sense to have it defined in mbedTLS Kconfig, and different parts
of Zephyr to reuse as needed (e.g. net-app vs upcoming TLS wrapper
for sockets).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Move the generated files into include/generated so they live with the
build and not in the zephyr source tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Create a net sample to setup a multi-node RPL mesh network using QMEU.
To enable this, it was necessary implement a hw filter on IEEE 802.15.4
UART Pipe driver and create a QEMU pipe management on cmake.
This sample use a tool developed on zephyr net-tools repository called
virtual-hub.
Signed-off-by: Pedro Martucci <pedropaulomartucci@gmail.com>
The Host header is even mandatory in HTTP 1.1, and indeed without
it, many virtual hosting setups don't work (which are many), so to
be faithful to what README says: "You can edit the source code to
issue a request to any other site on the Internet", let's
complicate the sample by including it.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This sample downloads a more or less big file (~6MB as preconfigured)
over HTTP and checks its hash for integrity. It also repeat such a
download indefinitely, counting total number of bytes transferred.
This is thus a kind of traffic load testing sample. (Ported to C
from MicroPython original).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The previous default, "config-threadnet.h", is more or less arbitrary
choice made in a commit 312def2c78 1.5 years ago. In particular,
it's not related to Thread support in Zephyr per se (there was no
such support at that time).
It doesn't make sense to have a default intended for a particular,
not widely used (yet) protocol. Instead, the default should work
out of the box with a contemporary widely deployed arrays of TLS
servers, which are HTTPS server. config-mini-tls1_2.h works with
https://google.com, and by extension, with many other servers on
the Internet.
So, have that as the default, and let applications with special
needs to override that to what they need.
Addresses: #6132
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
With 323e8cf069 applied and printf() working out of the box,
CONFIG_NET_BUF_LOG=y workarounds can be removed from configs of
all samples.
Also, print an intro message at the start of each server sample,
to give a user hint that the app didn't just hang and what to do
next. (The port waiting for connection is printed. We can't (easily)
print host address, because the samples should run on both Zephyr
and POSIX systems, and finding out local host address would require
hairy #ifdef's undermining the purpose of these samples (that is,
showing that the *same* code can be used on both types of systems)).
Fixes: #5379
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Redesign of the net_buf_simple and net_buf structs, where the data
payload portion is split to a separately allocated chunk of memory. In
practice this means that buf->__buf becomes a pointer from having just
been a marker (empty array) for where the payload begins right after
the meta-data.
Fixes#3283
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Make it easy to override HTTP host/port/path. Print URL which we
request and make few other adjustment to the output for clarity.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add samples config for nRF52840 with OpenThread
for echo_client and echo_server.
Add OpenThread to CI for echo_client and echo_server on nRF52840
Signed-off-by: Kamil Sroka <kamil.sroka@nordicsemi.no>
Add a simple UDP server application that will receive UDP data
and print various statistics like number of packets received and
dropped, amount of bytes received, and how many packets / sec
we were able to receive.
Currently the sample only provides a config file for FRDM-K64F board.
Note that this sample should not be run in QEMU as the performance
is very bad there because of SLIP link between Linux host and QEMU.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code couldn't really build with only CONFIG_NET_IPV4 or
CONFIG_NET_IPV6 enabled, because some parts weren't covered
by #ifdef's. Regroup the code to get it covered.
Also, improve error/notice messages.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
In order to be able to document the build on Windows and UNIX
systems, slight variations are required on the app commands
that are used throughout the documentation system.
This includes getting rid of the prompt symbol and providing commands
for both UNIX and Windows operating systems.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add configuration for zperf sample allowing to build USB dongle with
zperf for testing.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
At the moment CONFIG_SYS_LOG_USB_LEVEL name does not specify that this
is log level for the Device Stack. Make it clear renaming to the
proper name.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
A very old reference to former net stack was still lurking around.
Removing it.
Taking the opportunity to clear up dependencies.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
mbedTLS include directories will now default to be in the 'app'
include path when mbedTLS has been enabled.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Right now in FIN_WAIT1 state, if we receive FIN+ACK message, then
tcp state changed to FIN_WAIT2 on ACK flag and immediately on FIN
flag state changed to TIME_WAIT. Then final ACK is prepared and sent
(in queue at-least) to peer. Again immediately state changed to
TCP_CLOSED, where context is freed. net_context_put frees context
and releases tcp connection. Final ACK packet which is in queue
is dropped.
As a side effect of freed ACK packet, peer device keep on sending
FIN+ACK messages (that's why we see a lot of "TCP spurious
retransimission" messages in wireshark). As a result
of context free (respective connection handler also removed), we see
lot of packets dropped at connection input handler and replying with
ICMP error messages (destination unreachable).
To fix this issue, timewait timer support is required. When tcp
connection state changed to TIMEWAIT state, it should wait until
TIMEWAIT_TIMETOUT before changing state to TCP_CLOSED. It's
appropriate to close the tcp connection after timewait timer expiry.
Note: Right now timeout value is constant (250ms). But it should
be 2 * MSL (Maximum segment lifetime).
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The CoAP samples use an MBEDTLS config "config-coap.h" which could be
re-used by the LwM2M sample, except that most servers use a larger
maximum content length setting of 1500 bytes.
Let's add a CONFIG to set this for users of the CoAP lib and set the
CONFIG value for the samples to the 256 size currently used.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
- Mention the prj_dtls.conf setting
- Explain setting up security in the Leshan Demo Server web UI.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
The CMakeLists.txt file was reading ${BOARD}, but this means the user
must set BOARD like this cmake -DBOARD=foo. The user must be allowed
to set BOARD from the environment.
The code was unnecessary anyway because the convention
prj_${BOARD}.conf is known by boilerplate and therefore not necessary
to specify.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This introduces an nrf build to CI for the echo_server sample. Doing
so ensures that https://github.com/zephyrproject-rtos/zephyr/pull/5018
cannot regress again.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The echo-server compilation failed because mbedtls config file
was not found. Added suitable magic to CMakeLists.txt fixing that.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When sending TCP sample packet, just fill the packet to max and
ignore any overflow error.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
- Renaming NET_L2_RAW_CHANNEL to NET_RAW_MODE
- Create a generic IEEE 802.15.4 raw mode for drivers
- Modify the IEEE 802.15.4 drivers so it passes the packet unmodified,
up to code using that mode to apply the necessary changes on the
received net_pkt according to their needs
- Modify wpanusb/wpan_serial relevantly
Fixes#5004
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Check that we do not try to access fragment when UDP packet is
received if pkt is NULL. In practice this should not happen for
UDP but do the checks in proper order anyway.
Coverity-CID: 179252
Fixes#5057
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As we are checking that pkt is not NULL already in the start
of the function, remove the checks later in the code in function
zperf_tcp_receiver.c:tcp_received()
Coverity-CID: 179248
Fixes#5061
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The echo-client compilation failed because mbedtls config file
was not found. Added suitable magic to CMakeLists.txt fixing that.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add basic documentation about Ethernet over USB and describe
prj_netusb.conf configuration file.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
As per https://tools.ietf.org/html/rfc7230#section-3.3.2:
"A sender MUST NOT send a Content-Length header field in any
message that contains a Transfer-Encoding header field."
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
CONFIG_NET_L2_BT_ZEP1656 should only be used with older Linux up to
4.11 which by now should have been updated in all distros.
For those sticking with older distros should select it manually as
it does breaks IID address it should never be used in production.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Added conditionally enabled event state tracing support.
Needed for enhanced debug visibility of tight timed events where
normal print debug messages affect the timing of things. This is a
simple buffer that allows post analysis via gdb of what sequencer
events occurred.
Signed-off-by: David Leach <david.leach@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Removed some debug output and changed the level of others to reduce
the amount of information logged. The reason is that some of this is
causing false positive distractions.
- Removed enabling of FILTER error IRQ events. It isn't needed and is
only informational.
- Changed frame control AR bit inspection to use native retrieval
routine.
- Addressed some coding style issues.
Signed-off-by: David Leach <david.leach@nxp.com>
- Reworked the driver logic around TX/RX to correctly handle the
expectations of the underlying 802.15.4 hardware IP.
- Fixed a problem with TX always reporting an error to the stack
which resulted in constant retries.
- Fixed bug in RX to TX transition which would occasionally cause the
driver to error the TX.
- Changed RX logic to ensure that invalid RX frames were not passed up
the stack.
- Simplified hardware timer usage to only use TMR3.
- Added RX watermark and TMR3 support to fix a hardware problem where
the hw IP can get stuck on a receive in noisy environments.
- Modified samples/net/echo_client and echo_server kw41z project config
files to provide enanced debug visibility into stacks and threads.
Signed-off-by: David Leach <david.leach@nxp.com>
It is possible to access past end of url buffer by one byte.
Coverity-CID: 178790
Fixes#4784
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In http_request() a CRLF is added to the header information after
the protocol is added. 2 CRLF in a row means the header information
is done, so following header information will be ignored.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
All current socket samples as one of the points show portability to
POSIX platforms, and provide POSIX makefiles to let user build such
a version of application easily. These Makefiles were lost during
CMake conversion.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
KBuild would write the .inc file to the source directory, this was
changed during the CMake migration because whenever possible it should
be avoided to write files outside of the build directory.
But Makefile.posix assumes that these files are generated in the
source directory so we need to keep generating them there for now.
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Update the sample README with the latest changes during the
1.10 development cycle. We removed the 2 concurrent IPv4
and IPv6 connections and now the sample will make a single
connection based on whatever is configured (currently IPv6
takes precedence over IPv4).
Added instructions for how to switch the sample to IPv4.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
The QEMU_NET_STACK is enabled automatically if building
a networking application to QEMU so no need to do it for
each networking sample.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Rename netusb project file to be more general and support sanity build
for 96b_carbon board.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Create http library that uses net-app instead of net_context
directly. The old HTTP API is deprecated.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is similar fix as in commit 643cc4a22c but this one fixes
the thread parameter in UDP DTLS thread.
Fixes this function parameter datatype warning:
expected ‘k_thread_stack_t * {aka struct _k_thread_stack_element *}’
but argument is of type ‘u8_t * {aka unsigned char *}’
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The length and the start of the coap payload was not correct
because the received packet did not had IP and UDP header in place.
Fixes#4630
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This should clear up some of the confusion with random number
generators and drivers that obtain entropy from the hardware. Also,
many hardware number generators have limited bandwidth, so it's natural
for their output to be only used for seeding a random number generator.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Some "random" drivers are not drivers at all: they just implement the
function `sys_rand32_get()`. Move those to a random subsystem in
preparation for a reorganization.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Previously, post_write and execute callbacks returned 1 when handled
and 0 for error condition. However, this wasn't detailed enough and
the engine can't propagate any sort of error back to users -- so it
doesn't even check the return values in many cases!
Let's adjust the resource callback functions of all objects and the
lwm2m_client sample to return 0 for success or a valid error code.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Now that we can access resource data in the lwm2m subsys, let's use
the user provided firmware push buffer (5/0/0) to also store the
firmware pull data.
This way the size of the firmware pull buffer is completely up to the
application.
NOTE: This patch adds a 64 byte firmware buffer to the lwm2m_client
sample for this purpose.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Now that the LwM2M library can parse across multiple fragements,
let's remove the larger than normal buffer size setting.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Add configuration to http_server sample making it possible to work
with USB Device stack with Ethernet ECM protocol.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
If NET_L2_IEEE802154 and NET_IPV6 are enabled:
- NET_6LO is enabled
- NET_L2_IEEE802154_FRAGMENT is enabled
Thus removing setting this config options to yes where applicable.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Remove CONFIG_NET_L2_ETHERNET, as it's automatically set by the
board. This effectively makes prj_frdm_k64f.conf fairly portable,
e.g. the same config can be used for frdm_kw41z whcih uses 802.15.4
connectivity instead.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
LwM2M is intended for constrained devices. The default samples
settings are quite large by that standard and can be reduced to
reflect actual usage.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
After the LwM2M sample was introduced several HW related defaults were
added to Kconfig. We no longer need separate prj*.conf files for K64F
and qemu_x86. Let's combine them into a single prj.conf file and
adjust documentation.
NOTE: This also adjusts README.rst
Signed-off-by: Michael Scott <michael.scott@linaro.org>
We removed the default values for:
* CONFIG_USB_DEVICE_VID
* CONFIG_USB_DEVICE_PID
So put some dummy values in the sample.yaml to get things building
again.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fixes this function parameter datatype warning:
expected ‘k_thread_stack_t * {aka struct _k_thread_stack_element *}’
but argument is of type ‘u8_t * {aka unsigned char *}’
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IEEE 802.15.4 UART pipe config files in
echo_server/prj_qemu_802154.conf and echo_client/prj_qemu_802154.conf
did not had proper configuration options set. This prevents
qemu<->qemu communication between the echo-server and echo-client.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Vendor ID and Product ID should be assigned on build time by
respective process.
For sanity check we assign some random values which are only used for
build tests and should not be used for real products.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This sends out 2KB+ payload (i.e. guaranteedly more than 1 network
packet). When this sample was initially written, using such payload
quickly let to a deadlock somewhere in the network stack. However
as of now, running with such payload can sustain testing with
"ab -n10000" (10000 consecutive HTTP requests using Apache Bench),
so set is as a default, to serve as a mark point against possible
future regressions.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Applications may want to be notified when various events
happen in the LwM2M rd client. Let's implement an event
callback which sends: connect, disconnect and update events.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
1. Add handling block1 option in handle_request(). The basic idea is
to declare structure block_context at compiled time and use "token"
as a key to pick up the on-going block cotext. It should be able to
support multiple blockwise transfer concurrently
2. Use write callback implemented in lwm2m_obj_firmware to deal w/ the
update state transition and than call the callback registered by the
application
3. move default_block_size to lwm2m_engine.c to share between
lwm2m_engine and lwm2m_obj_firmware_pull
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: rebased on LwM2M net_app changes.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
1. Parse firmware pull URI
2. Add lwm2m_firmware_get/set_update_cb() for application to register
callback. This is because we want to check the update_state before
we pass to the application
3. Add lwm2m_firmware_get/set_update_result() and
lwm2m_firmware_get/set_update_stat() to manage the state transition
as well as the sanity check
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: rebased on net_app framework and
lwm2m_message refactoring.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This application does not do anything itself, it just waits
mDNS queries and responds to them.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Previously, there was boolean CONFIG_SLIP_DEBUG, which effectively
switched between "logging off" and "debug-level logging". Instead,
switch to CONFIG_SYS_LOG_SLIP_LEVEL (the naming of the option follows
existing conventions) which allows to select any of the standard 5
logging levels.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Explicitly call net_pkt_ref()/net_pkt_unref() to avoid packet being
freed after calling net_context_sendto() at retransmit_request().
Also, do not return when net_context_sendto() returns error. Instead,
we should keep retrying.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Original coap_client implementation does not setup "appdatalen" of
net_pkt correctly and does not strip the IP + UDP headers when doing
the retransmit. This will result in malformed coap packet. Fix it by
adding a strip_headers() function to set appdatalen and get rid of
IP + UDP headers.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
This helps to debug issues with mass connection handling (e.g. when
issues happen at ~500th connection).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
1. After calling sendto(), the packet will be unreferenced.
Call coap_pending_cycle() to make sure the packet is referenced until
we got the response from the peer or retransmission timeout.
2. In retransmit_request(), we rearrange the order to avoid the issue.
3. Remove IPv4 configuration for source code is expecting IPv6
4. Correct a typo in README.rst
5. Initialize the interface w/ IPv6 address
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
When testing against etsi_coaptest.sh, test cases TD_COAP_BLOCK_03/04
will get stuck. This is because these testcases send out a blockwise
transfer but with an empty payload. Although this should be a legit
request, large-update/create handlers did not check "MORE" flag in
block1 option and always return an error when request comes with empty
payload.
Corrected as below
1. Initialize coap_block_context when first block arrives.
(SIZE1 option is not always available. In the case that SIZE1 is
unavailable, the zoap_block_context will be re-initialized each time
a new block has arrived)
2. Check "MORE" flag of block1 option. If it's the last block, then
an empty payload should be allowed.
3. Response w/ 2.04 CHANGED when the last block has arrived for
large-update
4. Response w/ 2.02 CREATE when the last block has arrived for
large-create
5. Remove adding block2 option to the response since we are not sending
back any data to the caller
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
At 32 bytes the snprintk call to fill the help buffer was most often
running out of room and returning an error. Let's expand it to 64.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Users can private message the bot and the bot should respond directly
back to that user rather than rudely ignoring them.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Let's create a static global var for nickname so that we can use it
later without having to pass it all the way through callbacks, etc.
Also limit the size to 16 bytes as IRC servers will truncate anything
beyond.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
These structures were originally intended to prototype an IRC library
which would be later moved into the subsys/net/lib/irc folder.
Unfortunately, that effort has faded and they make this code much more
complex than necessary. Let's remove them in favor of simplicity.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
For style points let's declare the text shown at the beginning
of main() function to the top of our source as APP_BANNER so that
it's obvious and presents nicely.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Let's simplify the parsing function which scans incoming traffic
for carriage returns and let the net_pkt_read() function cross
multiple buffers if needed. Also, gracefully skip lines which
are longer than the command buffer.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Some L2 layers such as bluetooth need to have extra buffer pools to
hold copies of packets for use with TCP. Let's add support for that
so that future enablement of other boards won't get bitten.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Let's migrate from using NET_LOG_* functions to the SYS_LOG
facility which allows for granular control over the display
of info, debug and error messages unique to the file that
you're in.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Let's remove all of the extra coding to handle DHCP, DNS and event
management. This is all handled by the net_app API.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
It's useless now, arduino_101 has proven not working very well with x86
gpios and CC2520 never got to work properly there.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Only ieee802154 should have been using it, but it ended in various
samples that did not require it anymore once they've been using
net_app. Unlike former samples settings, net_app settings are tied to
net_app, so let's just forget about all of it and silently use net_app.
If something goes wrong in setting net options, it will be a unique
place.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This app now depends on net_app API, so it must be enabled for all
project configs we have.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
It's dumb, because it doesn't really parse HTTP request, just always
sends the same page in response. Even such, it's useful for socket
load testing with tools like Apache Bench (ab) and for regression
checking in the net subsystem.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Composite multifunction USB devices should be able to know about
configuration change, implement it through existing callback.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add information that IP addresses in prj_qemu_cortex_m3.conf file for
echo_client are set that qemu<->qemu communication could be tested.
Signed-off-by: Michał Kruszewski <michal.kruszewski@nordicsemi.no>
When TCP connection over IPv4 could not be established there was
an error about TCP connection over IPv6.
Signed-off-by: Michał Kruszewski <michal.kruszewski@nordicsemi.no>
This is the final stage of moving the LwM2M library internals to
the net_app APIs. This means we can support DTLS and other
built-in features in the future. All of the logic for
establishing the network connection is removed from the sample
app.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The LwM2M library does not use net_app APIs internally. To help
this effort let's establish a user facing structure "lwm2m_ctx"
(similar to http_client_ctx and mqtt_ctx) and start it off by
wrappering the net_context structure.
Future patches will add user setup options to this structure and
eventually remove the net_context structure in favor of a net_app_ctx.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The DNS resolver example enables mDNS client support and then
queries zephyr.local hostname. The net-tools project has example
avahi-daemon script that will response these .local queries and
can be used in testing.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Currently, we don't have a .conf which enabled BT. This will be
re-enabled at some future date after migrating to the full net_app
APIs by setting CONFIG_NET_APP_BT_NODE=y.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
There were bunch of config options in tests/net, net-shell and
wpan_serial sample, and those options had wrong name so they
were ignored by the code.
Fixes#1428
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IP header was stripped by _net_app_ssl_mux() when it received
IP packet. This is fine but if the application expects the get
the IP header, then there is a problem. Fix this by saving IP
header to ssl_context and then putting it back in front of the
packet when the data is passed to application.
Note that this IP header is not used by net_app when the packet
is sent because TLS/DTLS creates a tunnel for transferring packets
and user can only sent packets via this tunnel.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The default IPv6 multicast address count was too small,
increasing addresses to 5.
Jira: ZEP-2560
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The echo-server sample was using removed net_app_server_tls_disable()
function, the correct one is called net_app_server_disable()
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The stack name was incorrectly specified in mqtt_publisher sample
application, this cause compilation error when certain Kconfig
options were specified.
Jira: ZEP-2566
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The server needs global enable/disable status instead of only being
able to enable or disable just the TLS server part.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The main reason is allowing to run on 6LoWPAN devices, though also to
demonstrate IPv6 support with BSD Sockets in general.
Tested on 96b_carbon.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
POSIX requires struct sockaddr's field to be named "sa_family"
(not just "family"):
http://pubs.opengroup.org/onlinepubs/009696699/basedefs/sys/socket.h.html
This change allows to port POSIX apps easier (including writing
portable apps using BSD Sockets compatible API).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This is how it's called in the main docs, so use this same phrase in
Kconfig and samples too.
Also, added some articles to docs.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The documentation says that the API will automatically append the
net_buf fragment to the end of network packet fragment chain.
This was not the case and current only user for this API in
echo-server sample appended the fragment itself. The fix is to
automatically append the fragment to the end of fragment chain.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This commit adds IPSO temperature support to the LwM2M client sample.
NOTE: A dummy value of 25C is set during initialization and does not
change.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This sample utilizes the new LwM2M library by setting up default
values for LwM2M device and firmware objects and then establisting
a connection to a LwM2M server (for example Leshan Demo Server) via
the registration interface.
To use QEMU for this purpose please see:
doc/subsystems/networking/qemu_setup.rst
NOTE: This sample currently does not demonstrate DTLS/bootstrap as
neither of these is supported by the LwM2M library.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When unicast IPv6 address is added to network interface, it is
possible that the return value is NULL (if all the address slots
are already occupied).
Coverity-CID: 157607
Jira: ZEP-2467
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IEEE 802.15.4 settings are applied automatically by
net_app_init() function is is enabled by default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Don't call net configuration explicitly, instead rely on net_app
auto init service.
Thus, the only difference between POSIX and Zephyr versions of these
samples are different include files. The application code is 100%
the same.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The led demo does not even enable Bluetooth by default, and in case a
custom enables it shall use CONFIG_NET_APP_BLUETOOTH_NODE.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Make use of CONFIG_NET_APP_BLUETOOTH_NODE to enable advertising and
registering the necessary services.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The so called Router role don't require the IPSS, nor it should
advertise since it is not the peripheral in this case.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The so called Router role don't require the IPSS, nor it should
advertise since it is not the peripheral in this case.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Make use of CONFIG_NET_APP_BLUETOOTH_NODE to enable advertising and
registering the necessary services.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The so called Router role don't require the IPSS, nor it should
advertise since it is not the peripheral in this case.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The so called Router role don't require the IPSS, nor it should
advertise since it is not the peripheral in this case.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The so called Router role don't require the IPSS, nor it should
advertise since it is not the peripheral in this case.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Make use of CONFIG_NET_APP_BLUETOOTH_NODE to enable advertising and
registering the necessary services.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Make use of CONFIG_NET_APP_BLUETOOTH_NODE to enable advertising and
registering the necessary services.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Convert echo-client to use DTLS for UDP connections if DTLS
is enabled by prj.conf file.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Convert echo-server to use DTLS for UDP connections if DTLS
is enabled by prj.conf file.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Duplicate CONFIG_SYS_LOG_NET_LEVEL variable was defined in
config files so removing extras.
.config:58:warning: override: reassigning to symbol SYS_LOG_NET_LEVEL
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Couple of network samples had extra startup thread which is not
needed currently. This was an artifact before moving to using
unified kernel.
Jira: ZEP-2236
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Run http_server, http_client and https_client compile tests with
Bluetooth config. For http client tests we only use qemu_x86 as
the qemu_cortex_m3 tests failed because of too little memory.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If CONFIG_NET_CONTEXT_NET_PKT_POOL is defined, which is the
default for Bluetooth, then create the pool and use it when
sending network packets. This is needed when trying to send
TCP packets using Bluetooth IPSP.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There is plenty of memory for QEMU currently so no need to
manually set the amount of memory.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If CONFIG_NET_CONTEXT_NET_PKT_POOL is defined, which is the
default for Bluetooth, then create the pool and use it when
sending network packets. This is needed when trying to send
TCP packets using Bluetooth IPSP.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
CONFIG_MQTT_LIB_TLS is introduced to enable TLS support.
Also, prj_frdm_k64f_tls.conf is added to demostrate the whole idea.
jira:ZEP-2261
Signed-off-by: Aska Wu <aska.wu@linaro.org>
Use net app API since we want to enable MQTT with TLS.
mqtt_connect() and mqtt_close() are added to build and close the
connection to the broker. The caller doesn't need to deal with
the net context anymore and the most of network setup code in
mqtt_publisher is removed.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
When an app uses a construct such as:
obj-y = main.o ../../../../samples/bluetooth/gatt/hrs.o
in its makefile, it causes said object module to be built in the
source tree, not in the object tree.
When building massively parallel, this usually resuls on the files
getting corrupted, leading to bugs such as:
https://jira.zephyrproject.org/browse/ZEP-2316https://jira.zephyrproject.org/browse/ZEP-2317
src/../../../../samples/bluetooth/gatt/.gap.o.cmd:3: warning: NUL character seen; rest of line ignored
src/../../../../samples/bluetooth/gatt/.gap.o.cmd:4: warning: NUL character seen; rest of line ignored
src/../../../../samples/bluetooth/gatt/.gap.o.cmd:5: *** missing separator. Stop.
as multiple build are trying to touch the same file in the source tree
and of course, race and causes a build bug.
We have known about this issue for a long time, but it requires
modifications in the build system that there is no time to tackle.
A suggested workaround is to include the source files into a local .c
file, so this is what this patch does, to remove the random noise.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This PR enables Bluetooth stack if Bluetooth L2 is
compiled in.
Change-Id: I8f8127031140f0603615af44e0809d203db32f48
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
In many networking tests we had to configure SLIP in the prj.conf
leaving those configurations Qemu specific. This change enables SLIP for
QEMU targets automatically and allows reuse of prj.conf for multiple
boards.
Additionally, the TUN options is removed. This option was not used
anywhere.
To enable self-contained networking tests that do not depend on SLIP, we
introduce the new option NET_TEST which disables TAP and allows testing
in QEMU without the need for a host interface.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
kernel APIs have changed to using K_THREAD_STACK_DEFINE to declare stack
memory as well as K_THREAD_STACK_SIZEOF to calculate it's size.
Adjust irc_bot sample to reflect those changes.
This fixes stack related page faults when running irc_bot with
CONFIG_X86_STACK_PROTECTION enabled (which it is by default for qemu).
Signed-off-by: Michael Scott <michael.scott@linaro.org>
It's expected that there will be few socket-based samples, so move
tehm under samples/sockets/ to not clutter the main dir.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Implements asynchronous TCP echo server using non-blocking sockets
and poll, with concurrent connections support.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The coaps server sample application did not start because
number of IPv6 multicast addresses was too low. Increased
the address count from 2 to 5.
Jira: ZEP-2359
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
According to RFC7959 page 30, "The end of a block-wise transfer is
governed by the M bits in the Block options, _not_ by exhausting the
size estimates exchanges."
Therefore, we should check the M bit instead of total size (which
is not always available, too)
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Some README files referenced wiki articles that have been
moved to the doc area on the website.
Fixes#668
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Upcoming memory protection features will be placing some additional
constraints on kernel objects:
- They need to reside in memory owned by the kernel and not the
application
- Certain kernel object validation schemes will require some run-time
initialization of all kernel objects before they can be used.
Per Ben these initializer macros were never intended to be public. It is
not forbidden to use them, but doing so requires care: the memory being
initialized must reside in kernel space, and extra runtime
initialization steps may need to be peformed before they are fully
usable as kernel objects. In particular, kernel subsystems or drivers
whose objects are already in kernel memory may still need to use these
macros if they define kernel objects as members of a larger data
structure.
It is intended that application developers instead use the
K_<object>_DEFINE macros, which will automatically put the object in the
right memory and add them to a section which can be iterated over at
boot to complete initiailization.
There was no K_WORK_DEFINE() macro for creating struct k_work objects,
this is now added.
k_poll_event and k_poll_signal are intended to be instatiated from
application memory and have not been changed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Remove NET_UDP_HDR() macro as we cannot safely access UDP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the UDP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The config file for KW40Z has the shell disabled, as available
SRAM memory is limitted to 16kB.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
CONFIG_NET_IF_UNICAST_IPV6_ADDR_COUNT should be used instead of
CONFIG_NET_IFACE_UNICAST_IPV6_ADDR_COUNT.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Next two commits will increase the mbedtls ram usage a bit and
https client and server sample test will fail.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the net app API is automatically initialized, there is no
need to call net_app_init() by the http client and server sample
applications.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Removing CONFIG_NET_APP_SETTINGS from prj.conf file as the
sample does not use or need any IP addresses.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit will convert echo-client to use the net app API
when creating the connection to peer. Most of the network
setup code will be removed from echo-client by this commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit will convert echo-server to use the net app API
when creating the listening service. Most of the network
setup code will be removed from echo-server by this commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The network application API is a higher level API for creating
client and server type applications. Instead of applications
dealing with low level details, the network application API
provides services that most of the applications can use directly.
This commit removes the internal net_sample_*() API and converts
the existing users of it to use the new net_app API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Makefiles which start QEMU (make run) have been changed to operate
off of the QEMU_INSTANCE variable. QEMU_INSTANCE is simply appended
to the pid and sock file names. This makes us able to run multiple
QEMU Zephyr instances of the same sample.
Signed-off-by: John Andersen <john.s.andersen@intel.com>
This patch allows more generic USB configuration in the samples
and removes platform dependent driver configuration.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The example source code is POSIX-compatible (modulo include files),
i.e. can be built and behaves the same way for Zephyr and a POSIX
system (e.g. Linux). Makefile.posix is available for the latter.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The code has missing proper conversion from net_buf to net_pkt
that was implemented in commit db11fcd "net/net_pkt: Fully
separate struct net_pkt from struct net_buf"
The sample.yaml had incorrect whitelist string so this is also
fixed here.
Fixes#596
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We have many testcases doing filtering both on the architecture level
and the platform level, which is redundant. Also many testcases are
running the same test twice on the same SoC for no good reason, cleanup
the tests and cleanup the filtering.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The global mbedtls heap is set automatically now so no need to
set it individually in the http library.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We incorrectly had an arch_whitelist constraint set to 'qemu_x86' that
should have been a platform_whitelist, so fix that and add arduino_101
frdm_k64f to the platform_whitelist as targets that we can test this on.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The condition in src/Makefile is not necessary since the
net_private.h is always included from wpanusb.c and is not
dependent on the transceiver.
Change-Id: I07a0bf599f328bacb8c5677f20eb221a05f30866
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This will prepare test cases and samples with metadata and information
that will be consumed by the sanitycheck script which will be changed to
parse YAML files instead of ini.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some files have moved from their original location, or are no longer
available. For the mbedtls samples, tweak the link to point to a page
where links for current and previous downloads can be found.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This commit fixes compile error caused by commit 39962dc9
"samples: use k_thread_create()"
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This https-client sample starts to send HTTP GET/HEAD/POST
requests same way as http-client, to https server that can
be found in net-tools repository.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Various network samples contained QEMU slip setup instructions
or those instructions were missing. A reference doc in
doc/subsystems/networking/qemu_setup.rst file already has the
setup instructions for QEMU. So add a reference to that file
in samples/net/*/README.rst files and remove unnecessary slip
setup instructions in relevant files.
Fix various typos in readme files at the same time.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add clarification that the DNS server configuration must be edited in
the respective prj.conf file.
JIRA: ZEP-2040
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The number of RX and TX buffers is increased to 64 as the
earlier limit can cause memory exhaust in some cases.
Jira: ZEP-2223
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This fix is basically a no-op as the rx_buf pointer cannot be null
in practice, but in order to avoid Coverity complaining about
it add some null pointer checks to the UDP handling code.
Coverity-CID: 170124
Jira: ZEP-2235
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Waiting for an NET_EVENT_IF_UP before trying to connect isn't sufficient
in some cases; for instance, on devices using the MCUX HAL, such as the
FRDM-K64F, the interface will have the NET_IF_UP flag set even though
the link negotiation didn't yet complete.
Executing this sample on such board will produce the following output.
Notice the "Enabled 100M..." message right after trying to connect.
[dev/eth_mcux] [DBG] eth_0_init: MAC 00:04:9f:6f:91:da
net_context_connect error Is the server (broker) up and running?
[publisher:247] network_setup: -60 <ERROR>
Bye! [dev/eth_mcux] [INF] eth_mcux_phy_event: Enabled 100M
full-duplex mode.
Even though the returned error is ETIMEDOUT, increasing
net_context_connect()'s timeout parameter to several seconds isn't
sufficient; other steps performed by network_setup() after the link has
been fully established are necessary. As a stopgap measure, try
connecting a few times before giving up (more than one connection
attempt should be made by application in most cases, anyway.)
It might be the case that we need events to monitor ethernet link
(re)negotation in addition to the NET_IF_UP bit.
Jira: ZEP-2036
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If the HTTPS connection is closed, then properly handle call to
HTTP parser init in case of error and also remove any pending
data that belong to old connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There is not enough memory to run the HTTP server sample
application in Arduino-101 so remove the config file.
Jira: ZEP-2157
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit creates a HTTP server library. So instead of creating
a complex HTTP server application for serving HTTP requests, the
developer can use the HTTP server API to create HTTP server
insteances. This commit also adds support for creating HTTPS servers.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_sample_app_init() is now able to wait that both IPv4
and IPv6 addresses are setup before continuing.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
More general spelling fixes, and cleaning up stray UTF-8 characters
such as curly-quotes, em- and en-dashes. Use replacement strings
for |reg| and |trade|.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This creates a common API for network sample applications for
setting up IP addresses etc. The HTTP client application is modified
to use this API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of separate sample application that does everything
related to HTTP client connectivity, create a HTTP client library
that hides nasty details that are related to sending HTTP methods.
After this the sample HTTP client application is very simple and
only shows how to use the client HTTP API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We're moving the project code to GitHub folks, so change references
in the documentation from gerrit over to GitHub:
https://github.com/zephyrproject-rtos/zephyr
Change-Id: Ic491a62ed43fc799eb5698e92435cb6eb4d89394
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The sample in its default configuration waits for DNS server
configuration via IPv4 or IPv6 specific means. Until this
information is receives, DNS querying won't even start. Make
diagnostic messages explicit of this fact, because if user
doesn't have required services available in the network, the
sample will appear to just hang.
Jira: ZEP-2061
Change-Id: I56a5b7354a2d1239a35d8334ed95a15ebd19254f
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
net_pkt_get_len() is the correct API to get network packet
length.
Jira: ZEP-2076
Change-Id: Ifff6f3d5df28b3684cc8bb3758f9e8bccd5d4534
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Add config file to be used for testing KW41Z's IEEE 802.15.4 driver.
Jira: ZEP-2026
Change-Id: I7042c57ad33ff72b35d24fbf28085b99b2301726
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
The dns_resolve sample application did not had project file for
two boards that the README file is talking about, so adding them here.
Jira: ZEP-2040
Change-Id: I68e825854a171b09d56df91ab80ce5d9349733f6
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For stream-based protocols (TCP), adding less data than requested
("short write") is generally not a problem - the rest of data can
be sent in the next packet. So, make net_pkt_append() return length
of written data instead of just bool flag, which makes it closer
to the behavior of POSIX send()/write() calls.
There're many users of older net_pkt_append() in the codebase
however, so net_pkt_append_all() convenience function is added which
keeps returning a boolean flag. All current users were converted to
this function, except for two:
samples/net/http_server/src/ssl_utils.c
samples/net/mbedtls_sslclient/src/tcp.c
Both are related to TLS and implement mbedTLS "tx callback", which
follows POSIX short-write semantics. Both cases also had a code to
workaround previous boolean-only behavior of net_pkt_append() - after
calling it, they measured length of the actual data added (but only
in case of successful return of net_pkt_append(), so that didn't
really help). So, these 2 cases are already improved.
Jira: ZEP-1984
Change-Id: Ibaf7c029b15e91b516d73dab3612eed190ee982b
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I4ec03eb2183d59ef86ea2c20d956e5d272656837
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Most of these macros are not exactly exposing a buffer, but a specific
header pointer (ipv6, ivp4, ethernet and so on), so it relevant to
rename them accordingly.
Change-Id: I66e32f7c3f2bc75994befb28d823e24299a53f5c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- net_pkt becomes a stand-alone structure with network packet meta
information.
- network packet data is still managed through net_buf, mostly named
'frag'.
- net_pkt memory management is done through k_mem_slab
- function got introduced or relevantly renamed to target eithe net_pkt
or net_buf fragments.
- net_buf's sent_list ends up in net_pkt now, and thus helps to save
memory when TCP is enabled.
Change-Id: Ibd5c17df4f75891dec79db723a4c9fc704eb843d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This can be useful to override the default value, for testing.
Change-Id: I23b559152c71955ff5aa6fd3643f1f40f5594194
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
DNS resolving is better done with DNS resolve API so remove
the DNS client API which is quite hard to use.
Change-Id: Ide4973a5be674414ea6e04a35c938195cce40b6a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Modify the code to use DNS resolve API instead of DNS client API
as the latter is being phased out.
Change-Id: I6a7618d770621fee1f502d2bc277a162c589108a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In order to test the coaps_server sample app on
Arduino 101 board.
Change-Id: I7b393dac03a8020b7bd515c3b5b2fd961940bc21
Signed-off-by: Wu Jiequan <jiequanx.wu@intel.com>
Added bt test code in the http_server sample app and in order
to test on Arduino 101 board, added prj_arduino_101.conf file.
Change-Id: Ie68a81ee809e8618f70b5fab6fdbd66692401014
Signed-off-by: Wu Jiequan <jiequanx.wu@intel.com>
The context buffer pool was introduced to deal with TCP holding buffers
when 6LO may modify them, therefore it makes sense to have it enabled
by default when TCP and 6LO are enabled given that the code can deal
with NULL pool in case the application don't implement one.
Change-Id: I600ca31ab40c96ee27937c2e885e332b0cee4995
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Atmel SAM family GMAC Ethernet driver is implementing zero-copy
networking. As a result it has to reserve a defined amount of RX
data net buffers before bringing up the interface. Since net buffer
pool is initialized by the network stack and this driver was bringing
the interface up in its initialization function the driver initialization
was performed, as a workaround, after network stack initialization. It
is not a clean solution. This patch fixes this by bringing the
interface up in interface initialization function. The driver itself
can now be initialized before the network stack is.
Tested on Atmel SMART SAM E70 Xplained board
Change-Id: I65886fd6db6f27a10628e393cfabd8e5f78c08ff
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This addresses the issues found by QA in ZEP-1012 and clarify the
documentated behavior as described in ZEP-1859.
Change-Id: I602e5749db7f6f44cf5be449b8e6f0d2ba66b69b
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Docs need a label at the top so we can use :ref:`labelname`
to create a link to that doc from other docs.
Change-Id: I46cd75d714449de806a85dde08756c8e190488dc
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
- Let's use samples settings
- Enable both net and 15.4 shell modules
- Change prj_*.conf accordingly
Change-Id: If7e32a42c8dc7026d0580b1e94e819e1eda82e5b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
And use them accordingly in the common code part.
Change-Id: Id91b76e5baea607c0d68eebcde6f84e4e35ca44c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It can uses CONFIG_NET_APP_IEEE802154_* options instead.
Change-Id: I2501ca2015cfc1e68c6c384cb32c21084d2cb30d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In order to simplify when 802.15.4 is selected on these samples, let's
setup the device through a common code.
For this to work, RFD is now the default.
Change-Id: I46590864442f77d83f681cc0e854c94344648856
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
s/SAMPLES/APP for name shortening. Applying the change where relevant.
Not only IP addresse will be available as samples settings there but
also IEEE 802.15.4 channel, pan_id, and more for instance.
Change-Id: I05dd24989bd0c804d9588092d67044a3e063bc88
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The echo-server no longer uses multicast addresses itself,
so the multicast address setting can be removed from echo-client.
Change-Id: Ieab069849ced8a850ada6e6618d625695819be8e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The multicast address setting in echo-server was not really
used for anything so removing it from the app.
Change-Id: I8069c670388702fc46ae2f31506c982caa28212d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
At the moment CC2520 configuration options are selected inside "TI
CC2520 Driver RAW channe" submenu like:
[*] TI CC2520 Driver support ----
[ ] TI CC2520 Driver RAW channel --->
Make RAW channel depends on TI CC2520.
Change-Id: I92879b7f4391f1842c012b6c03c78956e90b9441
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
These are copied verbatim from the echo_server sample.
Change-Id: I56d1386144967177f889e12d4a173bfb6628f18b
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
The RX callback and timeout parameters were reversed in call to
mbedtls_ssl_set_bio().
Change-Id: I285694e57a024ac3ce735e496daad690f94737ac
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Due to commit 8308b9bd2d ("net/http: Add the HTTP/1.1 API")
every user of CONFIG_HTTP_PARSER would need to add CONFIG_HTTP to
their .conf files. Which is fine for intree samples/tests as they
have been adjusted, but the rest of world working on Zephyr apps
will need to make this changes as well.
Instead, we should have each of the following select HTTP instead of
depend on it, which will make future use of these configs and their
dependencies more intuitive:
HTTP_SERVER
HTTP_CLIENT
HTTP_PARSER
NOTE: As cleanup, this commit also removes the CONFIG_HTTP added to
samples and test .conf files.
Change-Id: I81cfaa19e37333b1bf98778f8147814780e7f77c
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Networking stack has split one global DATA pool to RX and TX DATA pools
and also added net_buf pool support to each context. Update the driver
to support this new design. Since the GMAC TX descriptor list has a fixed
size but the number of TX DATA buffers is no longer limited updating the
TX descriptor list has to be guarded by a semaphore.
Tested on Atmel SMART SAM E70 Xplained board
Change-Id: I181e1cdd183e173b85d5d1711b6e78cd5165666d
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Unref the buffer if net_contect_send_to() fails to send.
Change-Id: I182125e64aabd171cd86f42fd9e1de036dd68544
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
LLVM/icx compiler gives some warnings for signed vs unsigned
pointers.
Jira: ZEP-1884
Change-Id: Ide57be898ebd1bff49c8a27aac392fa58dcae726
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch adds the HTTP Basic Authentication routine "http_auth".
Authentication parameters are defined in the config.h file.
The README file is also updated by this patch.
Jira: ZEP-1543
Change-Id: I2d531966290e87a68c54fc1ac834491ac937df22
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Set a local define with the value previously defined at the Kconfig
file.
Change-Id: I3ee424c4a1102ca00c0059cb9d0a86498806486f
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Using a more efficent entropy call and proper output data
Jira: ZEP-1878
Change-Id: Ife738b84c1e56d58784b4fbc61ec0843579c4453
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
If we have not yet handled the previous RX buf, then we need
to drop the latest received one, otherwise the earlier net_buf
is leaked.
Change-Id: I1b69e07e8b3a3b87c76d923c847dc8316c128e76
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need to unref the net_buf in error path in RX and TX.
Change-Id: Icb6d43cb6b7411a5135ea09c6ae96742566fafc4
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The mbedtls_dtlsclient needs more RX buffers.
Jira: ZEP-1855
Change-Id: I80732c511dfade8fa9139e3bd26e21de73a68acd
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Sanitycheck cannot link the result qemu binary because it is too
large. As a workaround, disable mbedtls to get the linking pass.
.../real-ld: zephyr.elf section `noinit' will not fit in region `RAM'
.../real-ld: region `RAM' overflowed by 192 bytes
collect2: error: ld returned 1 exit status
Change-Id: I543571505ab9412db7eac101848c6032d1550d79
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The configuration file for Arduino 101 for the DTLS client
sample needs to define IPv4 and IPv6 addresses.
Jira: ZEP-1169
Change-Id: Iabfd5f067d39faaf8796aac84642b630b11ef7f6
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
This patch replaces some routines found at the HTTP client sample
application by the ones defined at the HTTP API.
Jira: ZEP-1824
Change-Id: Id19e3e346c09716ac95b0c488ff6e6949a5fbabe
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch removes some routines from the HTTP server sample
application and replaces them by the ones defined at the HTTP API.
Jira: ZEP-1824
Change-Id: Ia5db424d62997e01896294e12224aa65a58db432
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch adds the HTTP/1.1 API for Zephyr. This API consists of client
and server context structures enabled via Kconfig variables.
HTTP parser support is enabled via the CONFIG_HTTP_PARSER configuration
variable.
Currently, this API only includes support for writing HTTP requests
(client mode) and HTTP responses (server mode). TLS support is not
considered in this iteration.
Supported HTTP methods:
GET, HEAD, OPTIONS and POST.
Supported HTTP responses:
400, 403 404. The http_response routine may be used to write
any HTTP status code, for example 200 OK.
Jira: ZEP-1701
Change-Id: Ic9ccd4d4578d6d0f3a439976ea332b031644ca7d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Add the QEMU x86 project configuration file to the HTTP client sample app.
Change-Id: Ice6ae3f3559680e1d182506671984fd5f946f1d8
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Fix a printk format warning found at the HTTP client sample app.
Change-Id: I9665e3e59595b383d6e809af51fe4cf3cd8f8bd8
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Cast size_t to int in the http_client_cb code.
Change-Id: I36133da953669ec133421b5e7fb21bec9807fd06
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The invocation of net_if_ipv4_addr_add() should be included within the
conditional code that sets up the address added.
Change-Id: I9b4e76a6b4922b3455bc6b383431b4124d40a49e
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
GET and DEL requests may not have payloads, so it's not correct to
return with an error in those cases.
This was only noticed now that zoap_packet_get_payload() returns the
correct value for all situations.
Jira: ZEP-1754
Change-Id: Ie533041aa7a66855582ff4c5c937d943304bad84
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Bluetooth consumes buffer when transmitting them therefore any protocol
that need to retain them, like TCP, needs to have its own pool to copy
the buffers as they may need to be resent in case they are not acked.
Change-Id: I483c5a3eb4d54fae6b5b2902c69b67e8c2e0be5e
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
NATS is a publisher/subscriber protocol implemented on top of TCP. It
is specified in [1], and this is a sample implementation for Zephyr
using the new IP stack. The API is loosely based off of [2].
With this sample, it's possible to subscribe/unsubscribe to a given
subject, and be notified of changes asynchronously. In order to
conserve resources, the implementation does not keep its own track of
subscribed subjects; that must be performed by the application itself,
so it ignore unknown/undesired subjects.
TLS is not supported yet, although basic auth is. The client will
indicate if it supports username/password if a certain callback is set
in the struct nats. This callback will then be called, and the user
must copy the username/password to the supplied user/pass buffers.
Content might be also published for a given subject.
The sample application lets one observe the subject "led0", and turn it
"on", "off", or "toggle" its value. Changing the value will, if
supported, act on a status LED on the development board. The new
status will be published.
Also worth noting is that most of the networking and GPIO boilerplate
has been shamelessly copied from the IRC bot example. (Curiously, both
protocols are similar.)
[1] http://nats.io/documentation/internals/nats-protocol/
[2] https://github.com/nats-io/go-nats
Jira: ZEP-1012
Change-Id: I204adc61c4c533661eacfb8c28c1c08870debd91
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Fix the following error:
Calling "transmit(irc->conn, pong, ret)" without checking return value.
It wraps a library function that may fail and return an error code.
Coverity-CID: 163115
Change-Id: I525e1059e6a2ae3896f68760f1a8a6c68ecfc074
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Run both TCP and UDP to run at the same time. This requires two
extra threads in echo-client sample application.
Change-Id: I450a26d7ab1472150ea8f1309a43897a30bd4d90
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create net_nbuf_frag_del() so that we can track net_buf frees.
If CONFIG_NET_DEBUG_NET_BUF is not defined, then this new function
will call net_buf_frag_del() directly, and if not, then it will
track memory usage.
Change-Id: I5f382436cebc71fdaf12baf7bf964fb63bee7aca
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code used net_nbuf_get_reserve_{rx|tx}_data() function to
allocate a fragment. Instead of that low level function, use
net_nbuf_get_frag() instead. There are few places this is not
possible or is too big change like in few test programs.
Change-Id: Ied7e2b7db352de998b200ffa6ff82471bfa5ebe3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive lot of packets, it might happen that we exhaust
all the DATA buffers in the system. This would prevent from
us sending anything to the network.
Change this by splitting the DATA buffer pool into RX and TX
parts. This way RX flooding cannot consume all DATA buffers
that needs to be sent.
Change-Id: I8e8934c6d5fdd47b579ffa6268721b5eb3d64b6d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use context specific net_buf pool in echo-server and echo-client.
This will prevent application from allocating all available network
buffers in the system and thus preventing the core IP stack
functionality.
Change-Id: I3dbc64dd81c8a1165241426287a3530d00cbc7bf
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Using a more efficent entropy call and proper output data
Change-Id: I2ce71f63b6f22e5ceda79babd2eac802fa4bdf53
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Fix some style issues found at the src/main.c file.
Change-Id: I2023deb5ac4f31b2cf5d14d8313bbcfc03647898
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Move the client id define to config.h. Update the README file.
Change-Id: I1900c5e4f8c449e14279660d425501e86e07d409
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Remove the global bluemix flag and use a #define to set the
MQTT publisher topic and its parameters at compile time.
This change will save a few bytes and speed up computations.
Change-Id: I27bfc6b38c73d32c6105f1d506e147e9a5583097
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
It was assumed that the unit was microseconds, it is in miliseconds,
the same unit that is stored in the timeout field of the pending
transmission.
Change-Id: Ia99f363c7de4ec76a7ed229cb94a9964bcf609aa
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This adds retransmission support for confirmable responses sent by the
server.
Jira: ZEP-1732
Change-Id: I77c0c6375fa666e4cfdda4016ad1e0e90caf4ac9
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
It is possible that the buffer waiting for retransmission is modified
after it is sent, for example, it can be compacted by 6lo, and our
assumption of where is the message ID is located in the buffer is no
longer valid.
As the message ID is the only information that is necessary for
keeping track of retransmissions, we keep a copy of it in the pending
struct, as well as the destination address of the retransmission.
Change-Id: Id33d54353404628673541225a1a05e27ee08765f
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This implements the /.well-known/core resouce and two children
resources (/core1 and /core2) so the link-format feature is better
explained.
Change-Id: I9dd8c69040c952c5d12a9987c1966a71b0257ef2
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This adds the resource necessary for the TD_COAP_OBS group of tests.
Change-Id: I33bd09910f74db90ad0d713e4479ab2e3ec343a5
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Add the resource for the TD_COAP_BLOCK_04 ETSI testcase.
Change-Id: Ied901db34ce79d3e1f7f8c7fd55bc398b1f88640
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
The functions that retrieve net_buf will wait forever until a buffer
is available.
Change-Id: I03ddd1239f50fe4467e86e31c8fbfc9b05c8b190
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
- Let's build it with the various shell modules
- Make use of Kconfig.samples options
Thus: adding prj_server.conf and prj_client.conf to differentiate 2
instances of the app by their IPv6.
Then let's use samples/net/common/Makefile.ipstack
In the end, it is possible to build 2 times the samples this way:
make PCAP=154.pcap CONF_FILE=prj_server.conf server
and
make pristine
make CONF_FILE=prj_client.conf client
On client, or server, or both, shell commands can be used to ping each
other, check the statistics etc...
Once done, the given pcap file (154.pcap for instance) will have
recorded the traffic which can be parsed through:
wireshard 154.pcap
(Note: the "Malformed packet" warnings are not relevant, as the 15.4
frame FCS is a dummy one, it seems to make wireshark a bit lost)
Jira: ZEP-1774
Change-Id: I5590971660ecbfaac75af709124d59e1f98206fe
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
By default the net-tools package is expected to be located in
${ZEPHYR_BASE}/../net-tools directory. User can also specify
the directory using NET_TOOLS variable when running the make.
The net-tools package is located in this repository
https://gerrit.zephyrproject.org/r/net-tools
Change-Id: Ibccd7cabd567a630020fb9efbe1ec9e27b653b46
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit updates the 802.15.4 example to work with the
nrf5 802.15.4 radio driver.
Change-Id: I8a4c80a21ebe29ce2616836b764c454979ebb2e9
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
This commit addes new configuration for examples which use
nrf5 802.15.4 radio.
Change-Id: I0c57334d071fb58bc2282feb3f4e6b949ce5d472
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
Some files made it through review process with full license header.
Change-Id: I2722b127c40b4b19500042c12e4fde85a165bae9
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add a README.rst file to both echo-server and echo-client
sample applications.
Jira: ZEP-1539
Change-Id: I1ee1d02a3de0295697117f448d8e13f5b161e11b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Currently, for the following MQTT msg fields:
- client_id
- will_topic
- user_name
- topic
their length is computed inside the routine that receives the MQTT msg.
Although this simplifies development, also imposes one restriction:
data must be null-terminated. Sometimes, data is received from other
sources and not generated by the application, so the null-terminated
constraint may be considered problematic for the user.
This patch removes the assumption that string fields are null-terminated.
Current data structures are already prepared to handle this case, so no
API change is required.
Change-Id: I5a147a5b21e0da49541cbe62baac363c8737cd3e
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Add the QEMU x86 prj file to the MQTT publisher application.
Change-Id: I1ba8c3a3bf818d8f6dee7ea94021a83ba5277e5f
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This README file is no longer needed as we have separate
README files in various sub-directories.
Change-Id: I38d1c4208e373aa7aa23373149ef1b89fbcda094
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add the HTTPS (HTTP over TLS) server sample application on top
of the current HTTP Parser Library and mbedTLS. This code uses
TLS to stablish a secure connection and HTTP parser to identify
the request and the proper response.
Jira: ZEP-799
Change-Id: Ifbbcd0347bec47d12158440e50a82dc2966334d3
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Added conf files for qemu_cortex_m3, until a better solution
than CONF_FILE=prj_$(BOARD).conf exists in the makefile.
Change-Id: I1edc4f37bb3c49ecb65abf7c93b3c9f4608d601e
Signed-off-by: Richard Peters <mail@richardpeters.de>
Modify the network setup routine to accept the following parameters:
- network context
- accept callback
- server IP address
- server port
This change will allow us to reuse this routine for TLS.
Change-Id: I1fdbaa908783c69f87863cbc597b42f39358762c
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch adds the QEMU prj file for the HTTP server sample
app.
Change-Id: I0b910b5ec9970a7ffe9621e19d9544d899c22132
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Add information about how to run libcoap's[1] implementation of the
ETSI testcases against zoap-server.
Jira: ZEP-1538
[1] https://github.com/obgm/libcoap (branch develop)
Change-Id: I6aa5989575cc15630371aa0761bee98fb6fe1b80
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Turn down the default logging verbosity on the dhcpv4 frdm_k64f config
to focus on the dhcpv4 implementation.
Change-Id: Ifb450181add653951517a7b128b11657ec2bab62
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The example entropy_source implementation should write entropy to the
output buffer rather than to the context pointer which in this example
happens to be NULL.
Take the opportunity to reorganize the entropy_source to use all of
the entropy provided by a call to sys_rand32_get() rather than just
1/4 of it.
The entropy_source() callback from mbedtls is given a maximum amount
of entropy to return, rather than a minimum amount. Hence it makes
more sense to deliver exactly one chunk (32 bits) of entropy from the
call to sys_rand32_get() per call and let the mbedtls entropy handler
worry about how much entropy we actually need to collect (ie the threshold).
Change-Id: I57ed438de5cb1223619fde0fb8039d6eca284646
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The kernel provides an API call to get the least signficant 32 bits of
system time, use it rather than reaching under the hood.
Change-Id: I98fabdcadfd0a4fe5ae10226dabf4e6d31e88df6
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The kernel provides an API call to get the least signficant 32 bits of
system time, use it rather than reaching under the hood.
Change-Id: I9c303ef949f7670f2a2d9691c342e496873e96e6
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Core stack is not removing the network buffer if app data length
is zero. So memory leak happening here.
Change-Id: I3d354b5e7008396ca7cb977631036871998165b4
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Using net_buf_unref() technically works but debugging the network buffer
allocations is more difficult if done like that.
Change-Id: Ib8e3f8b412c2f8388315c2f63cae4392f814ea2f
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
size_t has different types depending on the arch selected for
building. Correct format identifier is %zu in this case.
Change-Id: I4388fcd8c5eb8bcd5997bb921bd80b4c2175b24c
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Fix build break introduced in commit 6b013c4721c5
("net: nbuf: Add timeout to net_buf getters")
Change-Id: Iaa521c6a49ae740eaee5276936442ab8aa4c47ba
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This commit changes the net_buf getter functions in nbuf.h
by adding a timeout parameter. These function prototypes
are changed to accept a timeout parameter.
net_nbuf_get_rx()
net_nbuf_get_tx()
net_nbuf_get_data()
net_nbuf_get_reserve_rx()
net_nbuf_get_reserve_tx()
net_nbuf_get_reserve_data()
net_nbuf_copy()
net_nbuf_copy_all()
net_nbuf_push()
net_nbuf_append()
net_nbuf_write()
net_nbuf_insert()
Following convinience functions have not been changed
net_nbuf_append_u8
net_nbuf_append_be16
net_nbuf_append_be32
net_nbuf_insert_u8
net_nbuf_insert_be16
net_nbuf_insert_be32
net_nbuf_write_u8
net_nbuf_write_be16
net_nbuf_write_be32
so they call the base function using K_FOREVER. Use the
base function if you want to have a timeout when net_buf
is allocated.
Change-Id: I20bb602ffb73069e5a02668fce60575141586c0f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit changes Kconfig prefix for ieee802154 drivers to
IEEE802154_*. This is done for consistency with config prefixes
used in other subsystems.
Change-Id: Ibbb4d96d2b748f4f13135bde85304ec34c5a90a6
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
Set protocol family value only after the buf is verified
to be non-null.
Change-Id: I0ce7bab3539087d0f522b4bb3024f46a7eb3c15f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch adds a basic HTTP client sample application.
The following HTTP 1.1 methods are supported: GET, HEAD,
OPTIONS and POST.
This sample application does not define an API for HTTP,
for more information see ZEP-346.
Jira: ZEP-827
Change-Id: Iee63a53f2ef424964f040eba20326d648249fc24
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Use a static buffer for sending UDP payload instead of reading
values from memory.
Change-Id: I037db5cd9b8784966d481c36e8cbe92d19760475
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Compiler was giving "Unused variables" warnings if IPv6 was
enabled and IPv4 was not, and vice versa.
Change-Id: I3b17534bb8bdef207512ea5b618e138edb420871
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IP address and port number were incorrectly parsed if
user used udp.upload command.
Change-Id: Ib37d481012af5e186a1e342c92d10ddef9fe35b1
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IP address family was not set correctly when setting up
the connection. This lead to connectivity error in udp.upload
command.
Change-Id: I598ff2675f97e10e2033763a497f7583c94f3840
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add the HTTP server sample application on top of the
HTTP Parser Library.
This sample application is based on TCP and HTTP chunk
transfer code found at:
https://gerrit.zephyrproject.org/r/#/c/9977/
A README file with sample output and a detailed
description of this application is also provided.
Jira: ZEP-820
Jira: ZEP-1542
Jira: ZEP-1556
Change-Id: I649104a256190577000bbac118136d5bc21f83bf
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This enables these samples to interoperate with Linux 6LoWPAN over
Bluetooth implementation while that is being fixed, in the long term
we might remove it from the samples once Linux is fixed.
Jira: ZEP-1656
Change-Id: I8ca9fe5a27f43cebc75b6fe5a436a5e8fcee26d5
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The DNS client sample application was updated to use IP addresses
from the prj_*.conf files. This patch updates the README file to
reflect those changes.
Change-Id: Ic72510be8da208aef19fb188560221e1c2386457
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Fix references to Qemu section and references to boards.
Change-Id: Ib2174ff698d57d3272073eecc71209e047961aaa
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Copy the documentation from the Wiki over here, the cross linking
between online documentation and Wiki and duplication of information was
inconsistent and confusing. Put everything in one place.
Change-Id: Ia3aaec1b431477e2ec54dbec2ccaa655870b0ee3
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
It doesn't really make sense for GET requests to have payloads, we
shouldn't even be checking if they have any payloads.
Change-Id: I4bb8cccd6c733a5825c2ca5067a990937c7045a6
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
- Reorganize some CONF variables and add the CONFIG_NET_SAMPLES_xxx
variables to the DNS sample application.
- Remove all the numeric IP addresses
- Use the CONFIG_NET_SAMPLES_xxx variables to define the IP addresses
Change-Id: Ib294d338f163f03ea1b47143b489d916578c532d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
- Move the MAX_ADDRESSES macro to config.h.
Document the meaning and usage of this macro
- Delete unused defines
Change-Id: I035feb605611e564db15cba77d6a3dce8409ca18
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Add the FRDM_K64F board to the DNS sample app testcase.ini
Change-Id: Iea8f7d09ed0d793711a5807f4bb67ed35ebf52c1
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit adds the MQTT Publisher sample application for Zephyr.
The following MQTT API routines are exercised in this sample:
- mqtt_init
- mqtt_tx_connect
- mqtt_tx_pingreq
- mqtt_tx_publish
- mqtt_tx_disconnect
The following MQTT API data structures are used in this application:
- struct mqtt_ctx
- struct mqtt_connect_msg
- struct mqtt_publish_msg
This sample application exemplifies how to send MQTT PUBLISH messages
with different QoS values.
A README file is also included in this patch.
Change-Id: I2b41b276d5178a2cd1b07b031c38bff481885fff
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Enable zperf code to support TCP using the native IP stack
when testing the network throughput.
Change-Id: I3e58754cfff65525ad15e63adf57f1ea22e4559d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When CONFIG_NET_DHCPV4 is selected, ignore the CONFIG_NET_SAMPLES_MY_IPV4_ADDR
setting and instead used DHCPv4.
NOTE: This commit also adds a placeholder for DHCPv6 behavior which is not
yet functional.
Change-Id: Id31fcb99be46e966babf18f94b5dec151920dedc
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When CONFIG_DNS_RESOLVER is active, the PEER config will be ignored and
instead a DNS query for DEFAULT_SERVER will be used.
Change-Id: If2c699944027f3c6a8ae9654f9cda0d7dca387c8
Signed-off-by: Michael Scott <michael.scott@linaro.org>
NOTE: You must set CONFIG_NET_IPV6=n in the project .conf file for
the CONFIG_NET_IPV4 setting to take effect.
Only 1 IP connection is active at a time. And when both are active
CONFIG_NET_IPV6 takes precedence.
Change-Id: I34a75f8d44db986810648d82a65d2ed29fc9a940
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Often IRC messages are split across multiple netbuf fragments.
Let's fix the message processing to account for this.
Change-Id: I3835af6adf337d27c28a0beeb72848dcc838772c
Signed-off-by: Michael Scott <michael.scott@linaro.org>
IRC won't allow 2 users to use the same user name, so let's add
a random number to the end of "zephyrbot" to make it semi-unique.
Change-Id: I56349de21823d8fd2c52646656615b42fc12de5e
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Currently, status can be 0 when a NULL buffer is sent to
on_context_recv() so let's not include status in our check.
And in the future, status parameter may be a non-zero value indicating
an error condition. So modify check to include positive values as well.
NOTE: Also make sure to use NET_ERR in these cases and not NET_INFO.
Change-Id: I8eac9a86d22b3b5624cd7a4e9d99e57afcac035f
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Instead let this be set via the project .conf file
Change-Id: Id8d7b46cc0888b83593b6f82dae619fb42c6ae3f
Signed-off-by: Michael Scott <michael.scott@linaro.org>
chan->irc won't be set after the "JOIN" transmit succeeds.
Change-Id: I935b0a44c94ec3d2c91b73db92bfd2005c27bb7f
Signed-off-by: Michael Scott <michael.scott@linaro.org>
samples/net/irc_bot/src/irc-bot.c:368:36:
warning: 'c' may be used uninitialized in this function
[-Wmaybe-uninitialized]
for (cc = &chan->irc->chans, c = c->irc->chans;
^
As suggested by Leandro Pereira <leandro.pereira@intel.com>
adjusted to:
for (cc = &chan->irc->chans, c = chan->irc->chans;
Change-Id: Icd490059e0b97f95408dd7bad3f1783a215c5edb
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Making a bit more room in these buffers. Some were not big enough
in certain cases, while others needed more room in general.
Change-Id: I47a4bb8c6635305f55dee323f7293b2e4cbed55a
Signed-off-by: Michael Scott <michael.scott@linaro.org>
K_FOREVER timeout in net_context_connect() will wait until
SYNACK has been received and we're ready to proceed with socket
communication.
To make the code as clear as possible, let's remove 2 callback
functions and relocate that code inside zirc_connect().
Change-Id: I6c64852ad5f48b24e1e6a58a741981e7d07bfd40
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Due to code restructuring we should move the following
functions higher in the code (above zirc_connect):
zirc_nick_set()
zirc_user_set()
zirc_chan_join()
Also relocate the function declaration for on_msg_rcvd()
to the top of the code.
Change-Id: I3936fb645b709dcbcfcc4212c127db819974c046
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Users can locate and edit these easier when they are at the
top as a #define.
Change-Id: Iecb53999cef1e70a80a28c7be5664ccde0fe7acf
Signed-off-by: Michael Scott <michael.scott@linaro.org>
By moving panic() function up to the top, other functions can be moved
later and still be able to call it.
Change-Id: I4290d1509cc64fc3f5fc5ec109cc19058090e6dd
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Instead use helper function where necessary.
Change-Id: Idcb47d02966731d7ef18588d1dccc8031a38d9d0
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The aim of this helper function is to remove duplicate code for setting
the parameters of in_addr structures.
Change-Id: Id882a5947c47a9b6f92924ce8fb04023540fbb8d
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This allows for a set app stack and threaded functions to be used later.
Change-Id: I647a3defdf6eb4cca2a4a21192b20641f5bf8d4a
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This is a sample IRC bot program, written using the new IP stack API.
All it does is join an IRC channel, wait for some commands, and react
to them:
!hello will greet whoever sent the command
!random will generate a pseudo-random number and send it back
!led_toggle will toggle an LED in the board [1]
!led_on will turn the LED on regardless of its current state
!led_off will turn the LED off
!rejoin will part the current channel and join again
!disconnect will quit from the IRC server
As far as the IRC protocol goes, it doesn't do much more than this, but
it should be straightforward to add support for other things (such as
notices, CTCP, DCC, etc) if someone is inclined to do so. However,
that's way beyond the scope of this sample, which is to show how to use
the network API to write a TCP client.
Some things are still missing as an example of how to use the APIs,
namely DNS resolution, automatically setting up the network with DHCP,
maybe saving settings on EEPROM. These are good candidates to be added
in the future.
[1] The LED code has been shamelessly stolen from the CoAP sample code.
Change-Id: I7152e97c0726f3559db545579ae8ae8d07bf04cd
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Michael Scott <michael.scott@linaro.org>
It will setup IPv4/IPv6 addresses. Telnet is ran in the background,
along with net and kernel shell modules.
See the README.rst for more information how to start and use this
sample.
Change-Id: I3e935014c79b534aab43a6fa8256792b23abb38e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Allow build-testing zoap-server with support for the CC2520 radio.
Change-Id: I986afd7b15208d477bd79f42a52dd45b217214cb
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
In case the user wants to use BOARD make variable to conveniently use
another board with this sample.
Change-Id: I6dd0656da223218d116dd498c1336c890563b212
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
net_addr_ntop() will convert IPv4|6 address to string form.
Renamed existing net_sprint_ip_addr_buf() to net_addr_ntop()
and adjusted parameters as per API.
Jira: ZEP-1638
Change-Id: Ia497be6bf876ca63b120529acbadcfd9162a96e3
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This configuration file allows using the device 802.15.4 radio for
IPv6 networks.
Change-Id: I9b3ee9a64acb71e97e4e8f7aae3e619196ad0462
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Currently, the function accepts a struct sockaddr * but the code
immediately type casts this to either in_addr or in6_addr. This is
incorrect behavior as the first field in a sockaddr is sa_family_t
and not address data.
So without special knowledge, a developer will use a sockaddr structure
as the parameter and then wonder why the address information isn't being
set correctly.
Let's change this parameter to void * which makes this function similar
to inet_pton().
Jira: ZEP-1616
Change-Id: I1fc9368da999d90feb07c03fac55dcc749d4eba6
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1492
Change-Id: If6acbaabf0857425684e0ab2d4db513e5bbc7b77
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
There are a few arrays we use with print_number and parse_number. These
functions expect a const uint32_t so lets have the arrays for TIME_US,
KBPS, and K match.
Change-Id: I6347b06af2374d702144084bb6b538a478fb8fac
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit enables echo-client application to start to
send data over TCP connection.
Change-Id: I9acdaae7f1e8411952c30caeedc9c1fb07cdd448
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Option CONFIG_NET_IPV6_NO_DAD is not used anymore, clean project
configuration files.
Change-Id: I368e076d2f79f1d4bc86edee11ff5befe37362c8
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The cause for this change is TCP. Until now, the radio strategy driver
(ALOHA or CSMA) was providing the actual nbuf, and not the buffer
fragment, counting on the fact that the loop was using
net_buf_frag_del() which made so, iteration after iteration, buffer
framgent to be always buf->frags. The problem with this logic is loosing
the fragments that might be still referenced by TCP, in case the whole
buffer did not make it so TCP can retry later and so on.
Instead, TX now takes the nbuf and the actual frag to send. It could
have been working with just a pointer on the data, and the whole length
of the frame. But it has been avoided due to possible future devices,
that will be smarter and run CSMA directly in the hw, thus it will
require to access the whole buffer list through the nbuf.
Change-Id: I8d77b1e13b648c0ec3645cb2d55d1910d00381ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The option is no longer used so it can be removed.
Use CONFIG_NET_IPV6_ND option instead.
Change-Id: Ibaa3d3deb52b8b176e85f8b9e1d8c80c1026aea1
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This is meant to test telnet console easily, as echo_server already
enables net shell module etc.
Change-Id: I045340ae5d6e179ea5ce1416cd7d67c6956bd973
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add configs for MCR20A device to echo_server and echo_client.
Change-Id: Ic0e310c0eb2eefe6ce5752a20b0c079b7ea8757c
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Only CONFIG_NET_SLIP_TAP will select SLIP, UART_PIPE,
UART_INTERRUPT_DRIVEN and SLIP_TAP. Otherwise apps will crash on
qemu.
Jira: ZEP-1617
Change-Id: Ibefbe708deb05e28b43ed4225211a5af655cec8d
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Use printk(), snprintk() instead of printf() and snprintf().
CONFIG_STDOUT_CONSOLE is anyway disabled by default so printf()
will not output anything without it.
Change-Id: Ide24e4d669e9821289189ed28e30a596120d9611
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Instructions to verify DHCPv4 client functionality in QEMU and
FRDM_K64F.
Change-Id: I623128186387c0c3237c8e759b949a3d0fde0993
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
After queueing full packet to RX queue we set pkt_curr to NULL, if we
get right after that SLIP_END we shall check for pkt_curr to avoid
NULL pointer assignment.
Coverity-CID: 157574
Change-Id: I2be40a652867e73b4a1994f529dc21980ecb35b4
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Some applications are not prepared for using multicast address and
specifying the interface, so it may be convenient for the user to be
able to use a unicast address when communicating with the
samples. This aligns this sample with most of the networking samples.
Change-Id: Ic97ea5a346a650751b6e2cbfefad25a3e700278c
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Samples instructions are to follow the rst format so they are
consistent with the rest of the documentation.
Change-Id: I37f06139484a4632e5b9c720ce1317feab68358b
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Change hard url into :ref: to board documentation
Change-Id: I9d8a585bb0e7274cf3233eadac2e303cc98ef86a
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The headings on some .rst files were not following the expected
heading order of using # for h1, * for h2, = for h3, and - for h4
This patch fixes that, and the doc/templates/*.tmpl files created
for folks to use as templates for creating board and sample docs.
Change-Id: I0263b005648558d5ea41a681ceaa4798c9594dd9
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
If we receive 0 byte packets from the network, we need to
ignore those as otherwise it is possible to leak network
buffers.
Change-Id: Id4b5b0d03c0b6d1e16634ff2d1960ea4728c8aa1
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Because net_buf_frag_del() returns the next fragment in the list,
we can use the return value which makes the code nicer looking.
Change-Id: Ic3d0155417b52a34bfbaa918570ff9af95aee468
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Return and clean buffer when fragment can not be allocated.
Coverity-CID: 157590
Change-Id: Ic8844609da4049623a6cf0c2ae037b2b777542e9
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Print assigned address and other information if client receives
anything from server. E.g. subnet, lease time and router.
Change-Id: I759d59522930401766452eb1fb3d57d1a8295a67
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
ENC28J60 has numbers on the board. Documentation has information about
signals only. Wiring will be easy with pin numbers.
Change-Id: I0afd6058a9417b679ef6358304737bf256aa3522
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
These logs are mandatory to spot buffer leaks. Unfortunately, they are
still not detailed enough to spot the actual place where the leak
happen.
Change-Id: If36dfa7a54aa1546fb268301f369b5ecd046e276
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In case of a GET request do not error if there's no payload or queries
parameters.
Change-Id: I29b2225700c83a8a2dad166146288dd55bd8f3de
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This resource verify the capability of the server to send a response to
a POST including a Location-Query option.
Change-Id: I4b663e813eb713d7e93a3c2f8cfd58c335b24cde
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
The CoAP test suite expects a specific path included in the
Location-Path option in the response.
Change-Id: Ib7616f9ad318fa93dc862f686429edb5084306e3
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
The Californium tests expects that all GET responses include the
Content-Format information of the response. In our case, all responses
are of type plain-text.
Change-Id: I08844825f31ed8f4c54020a41b9172cef5da6d70
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
So the sample zoap server application is more conformant, include the
token from the request, if any, in the response.
Change-Id: I5aacc1a3f81ebeaf473d327163c952b829489b01
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
The Californium test suite considers an error responding a NON_CON
request with a ACK response, even if the spec says it is valid, so add
support for using the correct type of response according to the
request.
Change-Id: I211c8a135b8db83af442a1d645b7ea0826dbbdec
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This allows to verify that the CoAP server is able to handle a
blockwise PUT request.
Change-Id: I801e353a27b10a5266748591d023bcb607db6bb4
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This adds support for TD_COAP_BLOCK_01 and TD_COAP_BLOCK_02 tests,
which test that the CoAP server is able to handle GET requests with
blockwise tranfers.
Change-Id: Id0d1703adcf5d4e76dd1bc489c8bcc94a3fd90bc
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This resource is used to verify that the CoAP server is able to send
responses in two steps: 1. only acknowledge that the request was
received and is going to be handled; 2. The actual response, with the
payload.
Change-Id: Ia77cc0ee9805e6cc120c57f4598c68ad364882a0
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
DHCPv4 sample was running on main stack. Updated to run on its own
thread. Update config options (removed unnecessary ones and separated
few options for easy readability).
Change-Id: I3be38ca4cd4bcfa62e2613b90b104679cff2517e
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This patch removes legacy configuation variables found at the
prj_arduino_101.conf file of the DNS sample application.
Change-Id: I74e370a7be177f809d805525cc18f594a59e38c0
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
All sample applicatons in Zephyr, using the ENC28J60 driver, set
the ETH_ENC28J60_0_GPIO_PIN Kconfig variable to 19.
However, in the Kconfig.enc28j60 file this variable is set to 24.
That default value, 24, was used only during the first iterations
of this driver and never used again.
In this patch, we set the Kconfig variable to 19 and simplify
project configuration files by removing one line.
Change-Id: I3d5fd9da04a3f10845d2a409de56f5b9c235e995
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Remove CONFIG_GPIO=y for the Arduino 101 board. This configuration
is now set by default in the board configuration file.
See commit 8f96628064.
Change-Id: I6fa73a5785d78c51f03a0af48fc2aa8cc7636c7d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The k64f has a random driver the TEST_RANDOM_GENERATOR config is not
necessary.
Change-Id: I73bc4076cac459388d9dd9bf3eb89c8cb5ba7db7
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
HTML documentation shows misaligned text that may be a bit confusing.
This issue was caused by wrong indentation. Furthermore, board specific
instructions to build the image does not include any instruction header.
This commit fixes the above described issues.
Change-Id: Ie965e09f32f46a9d69aac28c4b389084f06b31b6
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This makes it possible to setup a Bluetooth connection using net_bt shell
commands.
Change-Id: Ie4ae7e61345315ef987a00b6b5a28c0419f6b1c8
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the interface is not UP wait for MGMT event if that is enabled.
Change-Id: I4866c23d1e6f5b1a7cf212434d794673d7e756ce
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CONFIG_NETWORKING_WITH_BT no longer exist, instead
CONFIG_NET_L2_BLUETOOTH shall be used.
Change-Id: Ide353b7620228e431c535768b37749994caf8e8b
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It was missing for arduino_101.
Jira: ZEP-1574
Change-Id: I08fc0961b94f5f7b1b787ebf52e7d9922e38006c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
TCP didn't actually have a way to signal synchronous receipt of a FIN
packet. Extend the recv_cb API to allow a NULL buf argument with
status==0 (by analogy to Unix's zero-length read) to signal EOF.
Update docs too, and also echo_server which wasn't prepared to handle
this situation.
Change-Id: I7dc08f9e262a81dcad9c670c6471898889f0b05d
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The NET_SLIP Kconfig choice option doesn't really do anything for us,
plus we get warnings related to setting CONFIG_NET_SLIP=y in prj.conf
files.
Warnings like:
warning: override: reassigning to symbol NET_SLIP
warning: override: NET_SLIP_TAP changes choice state
So remove NET_SLIP choice and remove CONFIG_NET_SLIP=y in the prj.conf
files.
Change-Id: Ibccf9cf167f4c8a4df480ca0396bf83fcf60df1e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename cc2520 directory to hw and use it as generic
test application for the 802154 hardware driver.
Change-Id: I1c21505b7eb295279190f011a99c80e762178730
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add common log level for all IEEE802154 drivers.
Change-Id: If92c96b14e630d4482aadf9cacb25662d6663399
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Reformat and consolidate the samples/net/README and dns_client/READMExxx
files according to the RST spec.
Change-Id: I735190245204854ac5527e18971cc4c6478423e5
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Update the zperf/README.rst file with the following information:
- Homogenize the usage of "zperf", "iPerf" and "Zephyr"
- Update the Supported Boards section
- Clarify some instructions
- Add the Requirements section
Change-Id: Idfb29e2a5db9a78c19a6a27923f134583ebe5822
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Rename the project configuration files to pass the build.
The Makefile specifies the following format for the conf file:
prj_BOARD_PROF.conf. However, there are two files with the
following format: prj_BOARD_IFACE_PROF.conf. So, rename them
to avoid build errors.
Change-Id: I75e0d4169db881583b5f9a2b67deee46f66b6c97
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Remove commented line in the zperf/Makefile file.
Change-Id: Id869f21e923d3bb39fc31c5216ce29d78a0e1805
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Remove the reference to CONFIG_NET_UIP in src/Makefile.
Change-Id: I960413c17496c4b70b9c171a54ccfca4951b858b
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Sample projects that pair the frdm_k64f board with a cc2520 require
additional pinmux settings beyond the standard frdm_k64f pinmux. These
settings used the private k64 pinmux API rather than the public pinmux
API.
Because the mcux pinmux driver now always supports the public pinmux API
(vs. the k64 pinmux driver which only supported it in pinmux dev mode),
we can convert the frdm_k64f_cc2520 projects to use the public pinmux
API and the mcux pinmux driver.
Change-Id: Idfae8393171b007d8629e34bfae64255f55c6792
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Removes unnecessary CONFIG_ETH_KSDK project settings from the net
samples. Some of the configs no longer exist (MAC0-2), some are not
valid (MAC3-5) due to RANDOM_MAC=y, and the rest are already enabled by
default by the SoC and board.
Change-Id: I27079b8bb142ebc507885f3b1de07e282c813506
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This will replace the current goal of 'make qemu' with 'make run' and
moves Qemu handling into its own file and into the boards instead of
being architecture specific.
We should be able to add new boards that support some other type of
emulation (by adding scripts/Makefile.<emu type>) and allow the board to
define their own options for the use type of emulation.
'make qemu' will still work, however it will be deprecated, starting
with this commit it is recommended to use 'make run'.
Jira: ZEP-359
Change-Id: I1cacd56b4ec09421a58cf5d010e22e9035214df6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove legacy option and use SYS_CLOCK_EXISTS where appropriate.
Change-Id: I3d524ea2776e638683f0196c0cc342359d5d810f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This will allow inclusion of documentation files that exist outside of
doc/ and will make it possible to add rst files across the tree,
especially for boards, samples and tests.
Change-Id: I7afcf92d99f504b2bc0b2b7e3452acb2f8e08294
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is easier to test the 15.4 layer instead of hard-coding sample
logic.
Change-Id: I2376dec3dad9e2ceca3f61bd88bf5709f1bc1390
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It's currently hard to find a Beacon enabled network. So let's switch to
active scan for now.
Change-Id: I192e7c3128f9488fb680ea7f23221b2b4aa52188
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It will print-out the results, if any.
Change-Id: If988a6dc3c4504a8d4aa947d3d3f949870b638c8
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fixes two references to yaip that were were left behind after net/yaip
was renamed to subsys/net/ip. The zperf sample needs net_private.h, so
the include path is updated. The dhcpv4_client sample doesn't need it,
so the path is removed.
Change-Id: I189f1b58191524330254a5b7b31a9a4974956728
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Let's make net stack having its own level of debugging through sys_log.
It replaces NET_DEBUG by NET_LOG_ENABLED, which is then semantically
better: someone wanting to log the errors might want that not only for
debugging.
Along with it, CONFIG_NET_LOG_GLOBAL option is added, in order to enable
all available logging in network stack. It is disabled by default but
might be found useful when warning/errors need to be logged, so it is
then unnecessary to selectively enable by hand all CONFIG_NET_DEBUG_*
options.
It is possible, locally, to override CONFIG_SYS_LOG_NET_LEVEL by setting
the level one want to NET_SYS_LOG_LEVEL. This can be useful on samples
or tests.
Change-Id: I56a8f052340bc3a932229963cc69b39912093b88
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Re-instate the init_app()call which was accidentally removed by commit
commit 34f9391c9cf5 ("dhcpv4: Report address acquisition.")
Change-Id: Ic5ef70fd855a5bcb3ea1171de652994db493f4bb
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This will help to track only what's wanted (ipv6, tpc, udp, else...) if
needed to.
Change-Id: I5c2e5e582db629b5d0e1cd98004f693c50f532a4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It will be thus possible to enable only the error logging, or the other
sys_log levels.
Change-Id: I0c0ed789f7cfbb4811320e8f8249151288274873
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
printk can do the job properly.
Change-Id: Ib743328e046bdb29be26adfe5cd007aaa758cd64
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
When building the echo_client sample app, the following warning
is found:
echo-client.c:37:
echo_client/src/echo-client.c: In function 'send_ipv4_data':
include/logging/sys_log.h:108:20: warning: format '%d' expects argument
of type 'int', but argument 7 has
type 'size_t' ...
So, this patch changes %d by %zu to remove that warning.
Change-Id: I8a3822bca6d5988e531684d647de93bd77aabf9b
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
When using SLIP for TAP networking between guest and host, the correct
option is CONFIG_NET_SLIP_TAP. CONFIG_SLIP_TAP only enables it on the
SLIP side, it should be enabled on the networking stack, as well.
Change-Id: Ie1dacd07eb5a0891a572b08268a865f05a373690
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
When using SLIP for TAP networking between guest and host, the correct
option is CONFIG_NET_SLIP_TAP. CONFIG_SLIP_TAP only enables it on the
SLIP side, it should be enabled on the networking stack, as well.
Change-Id: I76226db9c587f1b5e9613244adab8f916ad94013
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Use the network management interface to catch and report IPv4 address
acquisition in the application.
Change-Id: Idd1bcaac90fffbd617600a7713206599e547826f
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Add build test to sanity_check to get a complex net app being built
for frdm-k64f.
Change-Id: Ib136f7964b65ad2167a3ed4484bff3bfe2a7ebad
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This moves the shell component into its own subsys and groups all
related files and options into a single place.
Additionally, one Kconfig option will now be required to enable the
shell:
CONFIG_CONSOLE_SHELL=y
The header files was also moved to include/shell/shell.h and can be now
referenced with
#include <shell/shell.h>
instead of
#include <misc/shell.h>
Updated documentation as well.
Change-Id: Iffbba4acfa05408055e9fd28dffa213451351f94
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The addresses used by the client were still made reference to the types
used by the old network stack.
Change-Id: Iaba919cb072e3295c9b371cc8fe493284c5b523b
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
The legacy IP stack was removed from the source tree, so this changes
were made to adapt to the native IP stack, but this might not work on
the galileo platform due the ethernet driver not being tested on the
new stack on TCP, but to have the reference application ready when
it gets integrated
Jira: ZEP-1448
Change-Id: Ifa6ea0afb3bc532dfb92b09debbf6eee59e38a25
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Add ARG_UNUSED to some function parameters to avoid
compiler warnings.
Change-Id: I5db5bc536f1eeb084e08d2fbe4a8b0a8456e67a5
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Move logging out of misc/ to its own subsystem. Anything related to
logging and any new logging features or backends could be added here
instead of the generic location in misc/ which is overcrowded with
options that are not related to eachother.
Jira: ZEP-1467
Change-Id: If6a3ea625c3a3562a7a61a0ba5fd7e6ca75518ba
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Removing useless options, refining the logging and of course setting the
right IP to make it work.
Change-Id: I0c0c1979d590bc4c4fcb3a1d1a252b87b0153511
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
When zephyr receives a 15.4 frames it allocates 1 RX buf (nbuf) and 1
DATA (buf), and it gets queued on net stack for post processing.
Problem: receiving a lot of frames is just completely nominal and very
fast (timing is critical in radio, and the rx thread of the radio driver
has a high priority, much higher than net stack's rx post processing).
So guess what happens when CONFIG_NET_NBUF_RX_COUNT=10 though let's say
12 packets are coming in?
The RX buffer pools gets empty and soon the system hangs on getting a
newly allocated one.
This proper CONFIG_NET_NBUF_RX_COUNT tweak fixes the issue, however some
future work will reduce the need of so many RX meta buf:
- l2's recv could be called right away at net_recv_data, before queuing
the buffer for post-processing, but this could affects reception
timing on radio side, which is critical.
- An l2 pre-processing (in the middle of what current l2 recv does)
could be implemented, it would be technology depenedent (aka: not
mandatory on all l2) and could quickly decide what to do and at best
drop the whole, or at least drop the RX meta buf (frag would still be
kept). Let's see.
Jira: ZEP-1427
Change-Id: Ic75b02efa36e35b450c02b3e6439a8d73f03f839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This patch adds the project file for the FRDM K64F board, it also
updates the README_IPv4 file to include instructions for using the
DNS resolver with the FRDM board.
Change-Id: Ic9b92c2fed2636b56044309dc3be7c829d828d35
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
enc28j60 can work up to 25Mhz, let's set a divider of 2 on the 32Mhz
host clock then. This require to mimic CS with a gpio in the SPI driver.
Change-Id: I98f84fa793a614cdbb566be39a262ff825101255
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will help testing dhcpv4 through frdm k64f ethernet port.
Change-Id: I7cf47d77b79041fe7ab408355d1a9f9332fc1f54
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This helps to test enc28j60 along with dhcpv4
Change-Id: I884f0aba0a04c3cc0d015d327cb9c100759d45ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Removes left over CONFIG_NETWORKING_WITH_BT which has been deprecated.
Change-Id: Ida3a2c2dba6e44f112711170f883c0582c3ee7ed
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fixes echo_client and echo_server samples.
Fixes compile error:
...
src/built-in.o: In function `fdrm_k64f_cc2520_pinmux_setup':
samples/net/echo_client/src/../../common/cc2520_frdm_k64f.c:93:
undefined reference to `_fsl_k64_set_pin'
samples/net/echo_client/src/../../common/cc2520_frdm_k64f.c:93:
undefined reference to `_fsl_k64_set_pin'
samples/net/echo_client/src/../../common/cc2520_frdm_k64f.c:93:
undefined reference to `_fsl_k64_set_pin'
...
Change-Id: I590f88f6bd083a30deea77fa860f001a3a55b278
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This commit adds the DNS client section to the samples/net/README file.
Added text includes a quick description of the application and
references to documentation already available in the tree.
Change-Id: Ia7ef3aea19069df5be2d8f14344b1afa750b22bd
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit adds the ARG_UNUSED macro for the status variable in
the udp_received callback.
Change-Id: I8c592cab72ccf5ba314742ef705e96d4a4d067e9
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit validates the size of the buffer used to store the
incomming datagram in the udp_rx routine.
Furthermore, two expressions related to the rx net_buf are now
executed before returning on error, avoiding a possible memory leak.
Change-Id: I30dc0a2d57dc207590387f1a9ab79945a1157ef5
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The DTLS client will use and asynchronous signaling method to
receive, this makes the sample work on QEMU
Jira: ZEP-1233
Change-Id: I28f074c4736f84c10e6be8119a5ba50b138fcc0d
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Previously, the domain names used in this application were
not very useful to proof that the DNS client was able to handle
multiple IP addresses.
In this patch, the number of domain names is increased. Some of them
may return multiple IP addresses as shown in the README_IPv4 file.
However, results may vary depending on the network setup.
Change-Id: Ic713ce48b4afa592c1480311f4394de6e57bf3fb
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch introduces a k_sem that will block until:
- data is received, or
- the user-provided timeout expires
This change allows us to simplify our previous DNS client
implementation.
This change is related to ZEP-1357 because we are refactoring the
DNS client API removing the continuous update of the net_context_recv
routine that seems to be causing issues after the kernel's update.
Jira: ZEP-1357
Change-Id: If01c9274ac8f096f0095a2872f86be2e007212ee
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit introduces the dns_context structure.
This new structure will reduce stack overhead due to
the simplication of the dns_resolve routine signature.
Furthermore, the timeout parameter is now int32_t
instead of uint32_t.
The dns sample application is also updated.
Change-Id: I5d789656bacbd23c4654edce5d116a88dc42c354
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This enables Bluetooth L2 driver with CONFIG_NET_L2_BLUETOOTH and
removes CONFIG_NETWORKING_WITH_BT which has been deprecated.
Change-Id: I6a75c105e45a1b748abf6a70234d415c5121bcdc
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enables Bluetooth L2 driver with CONFIG_NET_L2_BLUETOOTH and
removes CONFIG_NETWORKING_WITH_BT which has been deprecated.
Change-Id: I6f8b0e756f6e066b4b9cf9dec22f52fd72155c98
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Common code found in samples/net/common
App is built with:
make BOARD=frdm_k64f CONF_FILE=prj_frdm_k64f_cc2520.conf
Note: debug messages are enabled on many parts of the system, and these
are killing the timings. So it's not unusual at all to see rx errors on
cc2520 side. Without most of the debug, much less error will occur (if
any when dbg is fully disabled).
Change-Id: Ib6f0868c300652270661e72e80108804308164ab
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Moved all libc Kconfigs to where the code is and remove the default
Kconfig for selecting the minimal libc. Minimal libc is now the default
if nothing else is configured in.
Removed the options for extended libc, this obviously was restricting
features in the minimal libc without a good reason, most of the
functions are available directly when using newlib, so there is no
reason why we need to restrict those in minimal libc.
Jira: ZEP-1440
Change-Id: If0a3adf4314e2ebdf0e139dee3eb4f47ce07aa89
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Restructure the RANDOM Kconfig to match the structure used in other
drivers with a single top level menu. Move the true random number
generators to appear first in the menu, with pseudo generators at the
bottom. Do not present pseudo generators if a true random generator
is presented.
This change implies that tests, samples and applications that require
the random driver interface must now select CONFIG_RANDOM_GENERATOR.
In order for tests and samples to build (and run) on platforms that
have no random driver it remains necessary to select
the CONFIG_TEST_RANDOM_GENERATOR.
Note that CONFIG_TEST_RANDOM_GENERATOR retains its original purpose of
enabling a random driver that delivers non random numbers for the
purpose of testing only.
Change-Id: I2e28e44b4adf800e64a885aefe36a52da8aa455a
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Until now it has been necessary to separately define a k_fifo and
an array of buffers when creating net_buf pools. This has been a bit
of an inconvenience as well as blurred the line of what exactly
constitutes the "pool".
This patch removes the NET_BUF_POOL() macro and replaces it with a
NET_BUF_POOL_DEFINE() macro that internally expands into the buffer
array and new net_buf_pool struct with a given name:
NET_BUF_POOL_DEFINE(pool_name, ...);
Having a dedicated context struct for the pool has the added benefit
that we can start moving there net_buf members that have the same
value for all buffers from the same pool. The first such member that
gets moved is the destroy callback, thus shrinking net_buf by four
bytes. Another potential candidate is the user_data_size, however
right not that's left out since it would just leave 2 bytes of padding
in net_buf (i.e. not influence its size). Another common value is
buf->size, however that one is also used by net_buf_simple and can
therefore not be moved.
This patch also splits getting buffers from a FIFO and allocating a
new buffer from a pool into two separate APIs: net_buf_get and
net_buf_alloc, thus simplifying the APIs and their usage. There is no
separate 'reserve_head' parameter anymore when allocating, rather the
user is expected to call net_buf_reserve() afterwards if something
else than 0 headroom is desired.
Change-Id: Id91b1e5c2be2deb1274dde47f5edebfe29af383a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The random driver, if enabled, is initialized by the kernel
initialization function. There is no need for applications or tests
to re-initialize the driver.
Change-Id: Ib4712dda937a7a83a8079c8aa662cec03c5416f8
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Fix compilation issues that show up if SYS_LOG is mapped to printk
instead of printf. Unlike printf, printk is annotated so that the
compiler catches incorrect format specifiers passed to it.
Change-Id: Iab7cc6da110e9c98720211a6f773dcf055a3a411
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fixing a tiny build error found through sanitycheck.
Change-Id: Iee9a3ac135380ddf70e2902b532f6f28d417715c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
CC2520 is not embedded on an arduino_101, it is however possible to wire
one, and thus it requires to provide cc2520_configure_gpios() function.
This one, being common to a101 is found in samples/net/common.
Change-Id: I86f2734847edb3f6a968522afccc3099ed854d13
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Commit https://gerrit.zephyrproject.org/r/#/c/6971/ changed the
location of some include files, making compilation fail.
Change-Id: I43c124be28b55e550ef2204ca9faa7031665fb4a
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
This commit updates the dns client application to use the
new kernel API.
Change-Id: Ibf920532b02a1561bfb38f69e5dd994ab21574bc
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
* Moved networking code into subsys/net.
* Renamed net/yaip to net/ip at the same time.
* Fixed the tests/net to compile
* Fixed the Makefiles and Kconfig files in subsys/net
to use the new location of the IP stack
Change-Id: Ie45d9e8cb45a93fefdf969b20a81e3b1d3c16355
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Port the zperf network performance tool to native IP stack.
TCP support is missing from this version.
Change-Id: I2648e7d81014bb0cae8cf50854b0ae5f89a6567c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we cannot send a network packet, do not quit as that is
really not necessary here.
Change-Id: I7613d46bdbc849b75aaf0fc71c58beba810fd658
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the default board is qemu_x86, make sure there is similarly
named config file that can be used by default.
Change-Id: Ibc480d3b4eecc2601e3670c8da19be9c01833c36
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use by default a board specific config files for both
echo-server and echo-client sample applications.
This makes more sense than using the network technology specific
config file that was used earlier.
Change-Id: I155fc138f4b0ed1166f4e25267513afc3fb6fd76
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove legacy stack artifacts from the echo-server and echo-client
config files.
Change-Id: Icc591b9540495c4ee181517369b0df9bb91972bb
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This enables application debugging using qemu target:
export QEMU_EXTRA_FLAGS="-s -S"
make qemu
Was tested with echo_server
Change-Id: I1906dea2fbc5afe03b11729d2edb8f3629a629f8
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
As the native IP stack is now the default, there is no need
for corresponding Kconfig option.
Change-Id: I08e4992f540f928a2b7378e8803e634e38725348
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit removes the old MQTT and NATS publisher and subscriber
applications that were based on the uIP stack.
Change-Id: I7ba8e155e32ba0aa53c8dec1b6c0cc5170d70943
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit removes the legacy Contiki based uIP stack.
The new native IP stack must be used after this commit.
The commit also removes following things:
- legacy cc2520 driver
- legacy ethernet drivers
- legacy IP stack samples
and changes these things:
- disabled tests that only work for legacy IP stack
- select new IP stack by default
- enable random number generator by default as it is needed
by the new IP stack
Change-Id: I1229f9960a4c6654e9ccc6dac14a7efb9394e45d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
My IPv4 address was missing because of complex set of #ifdef's.
Change-Id: I6768587d3e104a57c10756bc43267f26068aa3cb
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Nbuf data size needs to be set to 128 bytes, specifically for
wpan sample.
Debug output kills timing, and thus can generate spurious failures on
reception, so limiting it to errors by default.
Change-Id: Ia918361d07369dacbe577e26855d7ef6ed865f7b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The used IPv6 or IPv4 address can be set in the config file.
This way one does not need to edit the source file to setup
the desired IP address.
Change-Id: Ic900bd4694481b4b035026ad0ba7b9280eb84e4a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Let the echo-server listen any configured IPv4 address
by default.
Change-Id: Ib83c5e069ae1e26615c37fa980bc4009b5a5e40c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user has enabled DHCPv4 support, then do not try
to set static IPv4 address.
Change-Id: Ia359f578044d72b951f53c509c92c09d575207f0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we want to receive packets to multiple addresses, the solution is to
listen on the ANY address, and add the address to the interface in
question (already done).
Change-Id: I383cc1401f1236ee05bdb010252a9f9909aa15bd
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Before using the LED we must set the direction of the GPIO pin to
output, and the LED will turn on when that GPIO pin is 'low'. So, for
our purposes, the LED is active low.
Change-Id: If8e6ce05ff2f3ddb7b17a87b172a91f7276194a4
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
'board.h' includes the definition of LED0_GPIO_PORT and LED0_GPIO_PIN,
without this include the fallback was used, as if the board in question
didn't have any LEDs.
Change-Id: I78ebdb2e2ffc41dff5011dcf9e33e09d70950e81
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This adds a configuration profile allowing this example to run on a
Quark SE C1000 devboard.
Change-Id: Ic04fd30a91ed0a1fc8c3a3b3a6e397f0722f50b1
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Nbuf data size needs to be set to 128 bytes, specifically for wpan
sample.
Debug output kills timing, and thus can generate spurious failures on
reception, so limiting it to errors by default.
Change-Id: Ia0b8c904e0bc66a7922af4f317db623db6c51462
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This adds the required code to echo server so that it works with TCP as
well.
Change-Id: Ib45dd91a52a60ddb4d8f0ae11175ceb52199c398
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Including shell allows to execute some kernel commands and make sure
system is not crashed.
Change-Id: I6157229614655dc7e523f1cf0f84ee7c58d7a717
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Due to huge delays with DEBUG log level change it to INFO.
Change-Id: I81caf78fc6e9e064c2ed8e18caa99351028af62a
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
In a case transmit is failed send ack to the driver with zero sequence
number which is not used for valid seqs.
Change-Id: I1047de9ab5de636c5a8983f31376046757c4dc0c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Following replacing semaphore with timeout semaphore transmit may not
be finished returning error after which communication stalls. Allowing
3 retransmits solves the issue.
Change-Id: Ibad05c2eac43dd6bb0ed72aaf16a7a2ef4185067
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Having 1024 bytes was really unsufficient and creating a lot of weird
bugs everywhere.
Change-Id: Ib642744fa6dfc9f3a699a0dc2f0c1783dc6f87b2
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Semantic has changed in k_sem_take in comparison with legacy
nano_sem_take.
Change-Id: I06129b6f15f66266919bf371c2358e5634109156
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is meant to test echo applications with 802.15.4 L2 directly in
qemu.
Change-Id: I0edccd8c39360421dc77e0064147221d86877bdf
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Previous commits support auto configured IPv6 addresses so no
need to manually tweak the address settings.
Change-Id: Ie641212981a04229721c84990a54876977d9cfc4
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit fixes the case when we receive large amount of
data and then copy it into new fragments. If the MTU is larger
than the fragment size, then it is possible that we might
overwrite net_buf memory and crash. This is typical in ethernet
network.
Change-Id: Ib1c65819c3bc718ec04f558e3df235246b5655dd
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The DTLS client will not longer use the legacy IP stack.
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Change-Id: I7402a188fc7501873d98d3b6cb2f03ee51f3506b
This commit allows echo-server to listen all defined addresses
specified to its network interfaces.
Change-Id: I52874210f6987c75d7921e514399a9eda55911bb
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
SLIP buffer size depends on maximum IEEE 802.15.4 frame size and start
byte.
Change-Id: I1cb0a848dce6b0c85bf11408733d777f7a3b03c9
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Remove unneeded SET_HW_ADDR_FILT since it is handled by other
commands and add missing opcodes.
Change-Id: I4b6488e6cee742b79c16789e817795138506dc77
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
It's 127 by default as soon as 802.15.4 l2 is selected.
Change-Id: I6c29d88bb3277a15fe54693027caf320bc3d9fc4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This demo showcases how to expose resources that are exposed using the
link-format feature.
Change-Id: Iad9421082fae3212cae58e6d6e9b88fa170678b8
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Forcefully set the IPv6 address in echo-client so that we
can use that address when sending data. Normally this should
not be done like this as the system should autoconfigure itself.
Change-Id: Id24f9aa84b30a3da941bb6b9e4522c7218687e12
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Makefile modifications to be able to be compiled with the unified kernel
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Change-Id: I0fce5d3f6b28df0cff4b7c0b554a787996e8c966
Print packet hexdump and interrupt related debug only when
VERBOSE_DEBUG is enabled.
Change-Id: Ieb997e3537a9a2316d1435372948004dd93babab
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Update information related to simple web server info.
Change-Id: Ib0155c116a3d53b374a7401eb6e9d1599390dba3
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Print packet hexdump only when VERBOSE_DEBUG is enabled and remove
debug print in empty functions.
Change-Id: Ifd3ae59001233f0237c4b7575bd92607c93e2ea0
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Forcefully set the IPv6 address in echo-server so that we
can use that address when sending data. Normally this should
not be done like this as the system should autoconfigure itself.
Change-Id: I99041539c50f994f5d3ddaabaf5cac8599d82078
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is a sample app using ECJPAKE crypto algorithm on DTLS, using mbedTLS,
native IP stack and the enc28j60 SPI Ethernet Driver
Change-Id: I658c3d9a54cfdd164a4147903125400f223c6e0a
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
It is the responsibility of the callback to release the buffer.
Change-Id: Id80f5f9ca190868a7c173994bb7ec7ee7f6251b7
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
When retrieving the address of a peer from the net_buf, care should be
taken so it happens before the 'data' pointer of the buffer is modified,
which causes the macros to retrieve the address from invalid positions.
Change-Id: I466fb989119ab5f7d0ac3899979670675bdaa946
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This change is related to patch called
"net: Adapt to new behavior of net_buf_frag_add"
This version removes extra net_nbuf_unref() from
the code. The unref was done because net_buf_frag_del()
did not remove the double ref from the list element.
Because of the other patch, the list does not have
double ref any more, so we need to remove the extra
unref in couple of extra places.
Change-Id: If90e01c24b9b4e68afbfa283850d2a1ecb3065ed
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change definition name suffix to WPANUSB
Change-Id: I3456ebff061866a67b7a07b33f6ff83a31a2d7a8
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This commit updates the README files to reflect that ZEP-1036
is already solved.
Information about ZEP-1097 and ZEP-1098 is now included.
Change-Id: I3c83160962d308d374823e086bbf083dca988606
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit modifies the conf and Makefile files of the DNS client
application.
Inside the Makefile, the CONF_FILE variable is updated to include
the BOARD name, therefore prj_'board_name'.conf is used from now on
to refer to the conf file. The right conf file is selected by passing
BOARD='board_name' to make.
Configuration variables at the conf files are also homogenized.
Change-Id: I6f5aaad0b52d458bceb90b315aba2b31f085c0a0
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Implement serial-radio protocol used in Contiki-based border routers
to interact with 802.15.4 devices connected over serial or USB-serial.
Change-Id: I938b34ca32ae7a08e5d48e3bea585cda6c98c113
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This creates initial TCP handling logic but does not yet
enable fully working TCP connection.
Some of the connection logic is taken from FNET TCP
implementation.
Origin: FNET 3.6.1
URL: https://github.com/butok/FNET/blob/master/fnet_stack/stack/fnet_tcp.c
Change-Id: I1e100d9fa9c91437562b933d94d0bd3db1a5885e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Current net_nbuf_write() api just appends data to last fragment. And
doesn't write data based on offset. That's why renaming this api.
New net_nbuf_write() apis based on offset will be coming soon.
Change-Id: Ie8e13e5f6091a279b62b6d8b0b3928a5187e75b0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This commit adds support for the Arduino 101 board with the
ENC28J60 Ethernet module.
Change-Id: Ib852e9cfb2b3b2188d3320e00d6bc24620e187f5
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This is a sample app using ECJPAKE crypto algorithm on DTLS, using
mbedTLS, and native IP stack
Jira: ZEP-900
Jira: ZEP-943
Change-Id: Ica17b047aab11b989d3e8c8f6ac1b79e3041053a
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
This ports zoap to the native stack.
Just for reference, and totally not scientific, here are the numbers
using the old stack:
$ size outdir/qemu_x86/zephyr.elf
text data bss dec hex filename
34657 10316 16916 61889 f1c1 outdir/qemu_x86/zephyr.elf
With yaip:
$ size outdir/qemu_x86/zephyr.elf
text data bss dec hex filename
30575 9148 6164 45887 b33f outdir/qemu_x86/zephyr.elf
Jira: ZEP-818
Change-Id: I7992a3e2af7d419081ee5a64d7cc2d49fb628ead
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Extends the echo server and echo client samples to work with YAIP
network stack with ethernet L2 layer and ENC28J60 ethernet device
on Arduino 101 boards.
Jira: ZEP-859
Change-Id: I242e5555aff18741bf00a551424b081b5396f4b3
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
This commit adds the DNS Client sample app on top of the new native
IP stack. This sample app supports IPv4 and IPv6. See README_IPv4 and
README_IPv6 files.
Origin: Original
Jira: ZEP-793
Jira: ZEP-855
Jira: ZEP-975
Change-Id: Id78bd634c44e216fd45b395c91d95b71ef68c976
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit removes the legacy DNS client sample code.
This patch is part of a commit series that will add support for
DNS client services on top of the new native IP stack.
Jira: ZEP-793
Jira: ZEP-855
Jira: ZEP-975
Change-Id: Ieb3366b21a365b8f77e576109c64c0fc4218aabb
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
In some cases the BT header files are missing and the compilation
will fail when done by sanitycheck script.
Change-Id: I484e1f0c23975053e947bc57ff3c9f4042fad71e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Export ieee802154 radio over USB to be used in other Operation Systems
like Linux. In this scenario Linux SoftMAC driver would be used
implementing ieee802154 stack inside Linux.
Currently tested to work with Raspberry Pi and addon ieee802154 board.
Change-Id: Iabcbbfcaad8e3935a63faca50a19fb624e78a351
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This will use the dedicated UART pipe driver to send/receive IEEE
802.15.4 "radio" frames.
- make
On one console:
- make qemu1
On a second console:
- make qemu2
Note:
net-tools is needed, cloned into net/tools
https://gerrit.zephyrproject.org/r/#/admin/projects/net-tools
Change-Id: I833cd40238b0653bb5b9a9b462fb4d5d2a3504b9
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- net tools directory is now in net/tools
- fixing the 80 chars line limit
Change-Id: I079880fa3449beffb326369ab23550dcba3ccf20
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
More samples will come. Current one is meant to test ieee802154 with
cc2520 on quark_se_devboard target. Some future sample will show how to
use the Qemu uart pipe fake 802.15.4 radio driver for testing on one
host.
Change-Id: Idea2b16cde091c7da926ca8aa71912fbfd0a3d62
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If no IP stack is seleceted, selecting one of the 2 cc2520 driver will
automatically select the relevant stack.
Change-Id: Icca22da190dc790ce6d302e14c45732f902e02ae
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- new stack options are renamed and placed in their respective menus
- new stack Kconfig gets normalized (tabs vs spaces, etc...)
Change-Id: Ia68f6589fed464bbdd76dc0812775684b2f94a58
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add socklen_t addrlen parameter to net_context_bind(),
net_context_sendto() and accept callback.
Currently the address length option is not really mandatory
as we can figure out the length from the address family.
But if we are going to support other protocol address families
it might be needed.
Change-Id: I59206465c3259050c469c5b2150221646a9a08d7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When running echo-server in the Zephyr device (either a real
device or qemu), set the IPv4 address to be 192.0.2.2. The host
IPv4 address should be set to 192.0.2.1 in this case. This change
is similar to IPv6 address change made earlier (now both IPv4 and
IPv6 addresses on device side end with "2", on host side, with "1").
Change-Id: I639b7be4403b4b2f38f01675d0ef56eaabf0f82c
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
When running echo-server in the Zephyr device (either a real
device or qemu), set the IPv6 address to be 2001:db8::2.
The host IPv6 address should be set to 2001:db8::1 in this case.
Change-Id: Ia967cecabece4b06a2f5a12b11c68a9de4aeb2af
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
