Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adds spi device tree bindings and nodes for the lpc54xxx and lpc55s6x
socs in preparation for adding a new spi driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The GIC-400 driver currently only supports SPIs because the (32) offset
for the INTIDs is hard-coded in the driver. At the driver level there is
no really difference between PPIs and SPIs so we can easily extend the
driver to support PPIs as well.
This is useful if we want to add support for the ARM Generic Timers that
use INTIDs in the PPI range.
SPI interrupts are in the range [0-987]. PPI interrupts are in the range
[0-15].
This commit adds interrupt 'type' cell to the GIC device tree binding
and changes the 'irq' cell to use interrupt type-specific index, rather
than a linear IRQ number.
The 'type'+'irq (index)' combo is automatically fixed up into a linear
IRQ number by the scripts/dts/gen_defines.py script.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add property for specifying the bus idle timeout for the NXP
i.MX/Kinetis LPI2C I2C controller.
Enabling the bus idle timeout helps the controller to recover from
e.g. EMC causing false clock pulses/spikes on the SCL line.
Without a timeout the LPI2C controller will assume that another bus
master took over the I2C bus and thus refuses to issue a I2C START
condition.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Erroring out for 'status = "ok"' broke backwards compatibility for a
downstream project. Accept it instead.
Maybe the error could be selectively re-enabled later.
The rest of the code only checks for 'status = "disabled"' (like the old
scripts), so no other updates are needed.
(It's a bit weird that we duplicate the property check in base.yaml.
Thinking of including base.yaml implicitly. Could clean things up then.)
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add support for the built-in Programmable Interrupt Controller
found in the SweRV EH1 RISC-V CPU
Signed-off-by: Olof Kindgren <olof.kindgren@gmail.com>
After switching to nrfx 2.0.0, the Kconfig choice options that allowed
enabling of pull-up or pull-down for MISO lines in SPIs and SPIMs are
not properly supported, they are simply ignored. This commit restores
the possibility of applying pull configuration for MISO lines.
In earlier nrfx versions, the MISO pull configuration could be only
set globally, in nrfx_config files, for all SPI and SPIM instances
together. Since nrfx 2.0.0, this configuration can be applied per
instance. This commit takes advantage of this possibility and instead
of using a common Kconfig option as a global setting for all instances,
allows applying individual instance settings via devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add new bindings for already supported (by lis2dh.c driver) lsm303agr
accelerometer. Using st,lsm303agr-accel compatible will allow in
subsequent commit to apply different sensitivity scale.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
NXP's LPC family of MCU's GPIOs parameters is udated.
Boards LPC54xxx and LPC55xxx have updated values according
pin and interrupt layout.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Provide a clear description of the how the binding maps nexus parent
pin indexes to header pin locations. Also use the standard name "Uno"
when identifying the header physical layout, contrasted with Mega/Due
which is a different physical layout.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Provide information required to allow the driver to put the flash chip
into a deep power down mode. This can reduce standby current by as
much as 90%.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The SPI NOR driver requires that the size (in bits) be provided in the
devicetree node. Update the binding to make the property required,
and update all nodes based on the memory chip identified.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This commit converts the existing hcm5883l 3-axis magnetometer
driver to use device tree for the I2C and GPIO selection.
It also adds a basic sample application for this sensor, using the
frdm-k64f development board to demonstrate how the interrupt
GPIO pin and I2C bus can be selected.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
The Generic FSK controller enables radio operation
using a custom GFSK/GMSK or MSK modulation format
achieved by programming a set of PHY variables such
as BT product
This binding describes the devices and its associated properties.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Convert bmg160 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert bmm150 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert max44009 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert mcp9808 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert sx9500 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert tmp112 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert th02 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update lis3mdl-magn dts binding to include GPIO interrupt pin and change
driver code to get the GPIO pin and controller info from DT instead of
Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit moves DMA parameters previously hard coded in the driver
to the dts.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a yaml file for help describing generic dma controllers.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update ccs811 dts binding to include GPIO pins for wakeup, reset, and
interrupt and change driver code to get the GPIO pin and controller
info from DT instead of Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update vl53l0x dts binding to include GPIO XSHUT pin and change
driver code to get the GPIO pin and controller info from DT instead of
Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the binding for nordic,nrf-temp to require the label property and
use the generated define (DT_INST_0_NORDIC_NRF_TEMP_LABEL) instead of
Kconfig symbol (CONFIG_TEMP_NRF5_NAME).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some chips supported by lis2dh driver (such as LIS2DH12 and LIS3DH)
contain CTRL_REG0 (1Eh) register to control internal pull-up on SDO/SA0
line (enabled by default). Add disconnect-sdo-sa0-pull-up boolean
device-tree property to allow disconnecting pull-up during driver
initialization. This allows to save around 180uA at 3.6V in
accelerometer power-down mode.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Create a common binding file that will be included by all bindings
handled by lis2dh.c driver. For now this includes optional irq-gpios
property.
Use introduced st,lis2dh-common.yaml in st,lsm303dlhc-accel.yaml in
order to support defining irq-gpios.
Also improve description of st,lis2dh-i2c.yaml to better match what can
be found in st,lis2dh-spi.yaml.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add SPI driver and bindings for LPSPI peripheral for the RV32M1 SOC.
Based heavily on the existing mcux LPSPI driver.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
- Add WDT(0,1) to esp32.dtsi
- Extend the module to be able to use WDT(0,1)
- Some minor refactoring due to usage of device tree
Tests:
- samples/drivers/watchdog
- tests/drivers/watchdog/wdt_basic_api
Note:
- timer module interrupt registers shall be removed when
timer driver implemented.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Unlike most other GPIO controllers which support 32 pins this device
only supports 16. (There is an SX1508B that has 8 pins, but the
driver doesn't support it.)
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
All 96Boards complying to the IE spec exposes either 40pin or 30pin
standard low speed connectors for peripheral connectivity. These
connectors are well defined and available in the IE spec. So, lets
create a devicetree binding for the 40pin header for the 1.8v IE
96Boards. This binding will be utilized by the 96Boards
for exposing the GPIO pins as nexus node as per the devicetree spec.
This will allow the shields and applications to use board independent
GPIO mapping.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
All 96Boards complying to the IE spec exposes either 40pin or 30pin
standard low speed connectors for peripheral connectivity. These
connectors are well defined and available in the IE spec. So, lets
create a devicetree binding for the most commonly used 30pin header
for the 3.3v IE 96Boards. This binding will be utilized by the 96Boards
for exposing the GPIO pins as nexus node as per the devicetree spec.
This will allow the shields and applications to use board independent
GPIO mapping.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add bindings for Nordic nRF family peripherals:
- IPC (Interprocessor Communication)
- RNG (Random Number Generator)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
MT9M114 is a CMOS digital image sensor.
Implement video interface.
Only VGA (640x480) supported for now.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The Thingy:52 has a LIS2DH12 low-power accelerometer on the external
I2C bus. Add the necessary description to devicetree.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Make the clkout properties of the NXP Kinetis SIM module device tree
bindings optional since not all boards rely on this clock signal for
clocking external peripherals.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add binding for arm,mps2-fpgaio-gpio and update device tree and change
FPGA GPIO init code to utilize device tree defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the selection of the IP clock source for the modules in the NXP
Kinetis KE1xF SoCs from being hardcoded in soc.c to being specified in
the device tree.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit adds LiteX SPI drivers and its bindings.
Signed-off-by: Daniel Craviee <dcraviee@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Indtroduction of generic device tree bindings for keyboard scan devices.
In addition, device tree node entries and dt specific bindings where
also implemented for Microchip MEC1501
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
This commit adds device bindings for Cortex-R4(F) and Cortex-R5(F).
These were supposed to be added during the initial development of
Cortex-R port, but it was not due to an incorrect device tree
specification.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Implemented latest extensions to the counter API related to
detection of alarms being set too late and short relative alarms.
Implementation could not be realized on nrfx_rtc driver thus
driver has been reimplemented based on nrf_rtc hal.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add #pwm-cells property in bindings for Nordic PWMs and add this
property with a suitable value assigned to all PWM nodes in dts
files for Nordic SoCs.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Looking at the code, this flag was probably made 'required: true' by
mistake. Combining 'type: boolean' with 'required: true' for 'ppi-wrap'
means that all nodes that use this binding are required to have a
'ppi-wrap;' property.
The mistake was hidden by a bug in edtlib (failing to flag missing
'required: true' booleans).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Implement a nice generalization suggested by Bobby Noelte.
Instead of having a generic #cells key in bindings, have source-specific
*-cells keys. Some examples:
interrupt-cells:
- irq
- priority
- flags
gpio-cells:
- pin
- flags
pwm-cells:
- channel
- period
This makes bindings a bit easier to read, and allows a node to be a
controller for many different 'phandle-array' properties.
The prefix before *-cells is derived from the property name, meaning
there's no fixed set of *-cells keys. This is possible because of the
earlier 'phandle-array' generalization.
The older #cells key is supported for backwards compatibility, but
generates a deprecation warning.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Generating generic information for 'type: phandle-array' properties in
edtlib was difficult due to defining phandle-array as just a list of
phandles and numbers. To make sense of a phandle-array property like
'pwms', you have to know that #pwm-cells is expected to appear on
each referenced controller, and that the binding for the controller has
a #cells.
Because of this, handling of various 'type: phandle-array' properties
was previously hardcoded in edtlib and exposed through properties like
Node.pwms, instead of through the generic Node.props (though with a lot
of shared code).
In practice, it turns out that all 'type: phandle-array' properties in
Zephyr work exactly the same way: They all have names that end in -s,
the 's' is removed to derive the name of related properties, and they
all look up #cells in the binding for the controller, which gives names
to the data values.
Strengthen the definition of 'type: phandle-array' to mean a property
that works exactly like the existing phandle-array properties (which
also means requiring that the name ends in -s). This removes a ton of
hardcoding from edtlib and allows new 'type: phandle-array' properties
to be added without making any code changes.
If we ever need a property type that's a list of phandles and numbers
but that doesn't follow this scheme, then we could add a separate type
for it. We should check if the standard scheme is fine first though.
The only property type for which no information is generated is now
'compound'.
There's some inconsistency in how we generate identifiers for clocks
compared to other 'type: phandle-array' properties, so keep
special-casing them for now in gen_defines.py (see the comment in
write_clocks()).
This change also enabled a bunch of other simplifications, like reusing
the ControllerAndData class for interrupts.
Piggyback generalization of *-map properties so that they work for any
phandle-array properties. It's now possible to have things like
'io-channel-map', if you need to.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit introduces separate "compatible" strings for DTS nodes
representing different types of Nordic SPI peripherals. Previously
"nordic,nrf-spi" was used for both SPI and SPIM. SPIS was already
handled separately.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/spi/
new binding for "nordic,nrf-spim" is added and common fields for all
3 types of Nordic SPI peripherals are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in spiX nodes are updated (when there is no
choice as only one type of SPI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/spi/
spi_nrfx_spim driver is updated with the new form of macros generated
from dts
* boards/
all spiX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of SPI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (SPI_x_NRF_SPI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the new 'compatible:' and 'include:' syntaxes, and clean it up like
for other bindings.
Shorten the description, because it appears in the output as a comment
above the generated macros, and it looks neater. I asked Mateusz what
kind of device it is.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use the new 'compatible:', 'include:', and 'required:' keys, and clean
it up like other bindings.
Shorten the 'description:' text, because it appears in the output as a
comment above the generated macros, and it looks neater.
Fixes: #19385
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add support for up-and-down counter mode, which aligns the center of
each channel's pulses instead of their initial edges. This is enabled
on a PWM periphral by adding the "center-aligned" property to the
device tree, e.g.:
&pwm0 {
status = "okay";
center-aligned;
ch0-pin = <15>;
ch1-pin = <17>;
ch1-inverted;
};
Signed-off-by: Jim Paris <jim@jtan.com>
Use the device tree to assign the correct peripheral clock to each
UART/USART/LEUART. Previously, the clock identifier was determined
through the sequence number of the instantiated UART. This meant
configuring all UARTs when only one of the later UARTs was required.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
This commit adds driver supporting reading DNA ID value for LiteX SoC
builder.
Signed-off-by: Jakub Wegnerowski <jwegnerowski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add RTC timer driver for CC13X2/CC26X2, and use it instead of systick
as system clock. It is necessary to use this timer for power
management support, so that the system can exit from deep sleep upon
expiry of timeouts.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Deprecate 'sub-node:' and add a more general 'child-binding:' mechanism
to bindings. Keep supporting 'sub-node:', but print a deprecation
warning when it's used.
Like 'sub-node:', 'child-binding:' gives a binding to child nodes, but
the binding is required to be a complete binding, and is treated (and
checked) like a normal binding.
'child-binding:' can in turn contain another 'child-binding:', up to any
number of levels. This is automatic from treating it like a normal
binding, and from the code initializing parent Devices before child
Devices.
This lets nodes give bindings to grandchildren.
For example, take this devicetree fragment:
parent {
compatible = "foo";
child-1 {
grandchild-1 {
...
};
grandchild-2 {
...
};
};
child-2 {
grandchild-3 {
...
};
};
};
The binding for 'foo' could provide bindings for grandchild-1/2/3 like
this:
compatible: "foo"
# Binding for children
child-binding:
title: ...
description: ...
...
# Binding for grandchildren
child-binding:
title: ...
description: ...
properties:
...
Due to implementation issues with the old devicetree scripts, only two
levels of 'child-binding:' is supported for now. This limitation will go
away in Zephyr 2.2.
Piggyback shortening 'description:' and 'title:' in some bindings that
provide child bindings. This makes the generated header a bit neater.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The arc_iot.dtsi used "intel,qmsi-ss-gpio" and "intel,qmsi-ss-i2c"
compatiables, however we have no drivers for these and it seems wrong
that the ARC platform would utilize such compatiables. Remove the
compatiable fields for now (proper one's can be added when there are I2C
and GPIO drivers for this platform).
Also remove the binding files associated with "intel,qmsi-ss-gpio" and
"intel,qmsi-ss-i2c" as nothing in tree utilizes them.
Fixes: 19227
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Instead of
child:
bus: foo
parent:
bus: bar
, have
child-bus: foo
parent-bus: bar
'bus' is the only key that ever appears under 'child' and 'parent'.
Support the old keys for backwards compatibility, with a deprecation
warning if they're used.
Also add 'child/parent-bus' tests to the edtlib test suite. It was
untested before.
I also considered putting more stuff under 'child' and 'parent', but
there's not much point when there's just a few keys I think. Top-level
stuff is cleaner and easier to read.
I'm planning to add a 'child-binding' key a bit later (like 'sub-node',
but more flexible), and child-* is consistent with that.
Also add an unrelated test-bindings/grandchild-3.yaml that was
accidentally left out earlier.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This driver was still using CONFIG_* values to determine its address,
IRQ, etc. Add a binding for an "intel,hpet" device and migrate this
driver to devicetree.
Fixes: #18657
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Add support to STM IIS3DHHC the ultra-low noise, high-stability
three-axis linear accelerometer.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The LIS2MDL is not a combo device, but pure magnotemeter.
Hence, '-magn' extension is not adding information and can
be removed from dts compatible name as well as binding filename.
Instead specify '-i2c' or '-spi' to distinguish between the names.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The KE1xF SoC family SIM unit differs from the other Kinetis family
SoCs. Add a unique compatiable and binding for it.
Fixes#18160
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- hw-flow-control added to uart.yaml as it is a common feature
- cleanup other related yaml files
- change property 'category' to 'rquired' in yaml files
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
- Fixes#3981
- Implement UART Polling functions
- Implement UART Interrupt APIs
- Remove dependency on esp32_rom_uart_xxx functions
- Update Device tree with UART addresses and pin config
- Update ESP32 UART KConfig
Notes about implementation:
- Interrupts now defined as a local macros, and should be removed
later on, when interrupts for esp32 are supported in dts
- Threshold interrupts are used for TX/RX
- Reseting FIFOs using _RST bit will corrupt FIFO of UART2 when used for
UART1 and vice-versa, so a generic way is used for all three UARTs
- Old Silicon rev is not supported
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
For quite a few peripherals that are currently supported by nrfx HALs
or drivers there are no definitions of corresponding CMSIS-Core
peripheral accessing symbols that would provide their base addresses
in the proper domain (secure or non-secure), accordingly to the build
target. This commits adds devicetree nodes for these peripherals so
that their base addresses can be used in definitions of the accessing
symbols mentioned above.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The 'irq-gpios' property is optional as the drivers work fine if this
property isn't set. The property is only required if "TRIGGER" mode is
enabled in the drivers.
As such mark 'irq-gpios' as 'required:false`.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
With the change to "compatible", and deprecation of "inherit"
and "category: required", there are multiple warnings when
running cmake. So fix those by updating the DTS YAML file.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Each intmux block acts like 8 interrupt controllers in which we can
have multiple device interrupts on a single channel and that channel
than interrupt than chained to another interrupt controller (in the
case of the RISC-V cores, it is the event unit).
So to describe things better to properly be able to walk the interrupt
chain in the device tree we treat each channel in the interrupt mux as
an interrupt controller rather than the intmux as a single interrupt
controller.
In the future this will allow the device tree generation code to walk
the interrupt chain from the device and up through any interrupt
controllers to generate the IRQ value that Zephyr expects (rather than
us hard coding this into the DTS).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Instead of
properties:
compatible:
constraint: "foo"
, just have
compatible: "foo"
at the top level of the binding.
For backwards compatibility, the old 'properties: compatible: ...' form
is still accepted for now, and is treated the same as a single-element
'compatible:'.
The old syntax was inspired by dt-schema (though it isn't
dt-schema-compatible), which is in turn a thin wrapper around
json-schema (the idea is to transform .dts files into YAML and then
verify them).
Maybe the idea was to gradually switch the syntax over to dt-schema and
then be able to use unmodified dt-schema bindings, but dt-schema is
really a different kind of tool (a completely standalone linter), and
works very differently from our stuff (see schemas/dt-core.yaml in the
dt-schema repo to get an idea of just how differently).
Better to keep it simple.
This commit also piggybacks some clarifications to the binding template
re. '#cells:'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fixes an upcoming error:
device tree error: 'hw-flow-control' appears in /soc/uart@40028000
in nrf52840_pca10056.dts.pre.tmp, but is not declared in
'properties:' in .../dts/bindings/serial/nordic,nrf-uarte.yaml
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 'category: required/optional' setting for properties is just a
yes/no thing. Using a boolean makes it clearer, so have
'required: true/false' instead.
Print a clear error when 'category:' is used:
edtlib.EDTError: please put 'required: true' instead of 'category:
required' in 'properties: foo: ...' in
test-bindings/sub-node-parent.yaml - 'category' has been removed
The old scripts in scripts/dts/ ignore this setting, and only print a
warning if 'category: required' in an inherited binding is changed to
'category: optional'. Remove that code, since the new scripts already
have the same check.
The replacement was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i \
-e 's/category:\s*required/required: true/' \
-e 's/category:\s*optional/required: false/'
dts/binding-template.yaml is updated as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Update the ADC bindings to include #io-channel-cells and update the
related dts files to set #io-channel-cells.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Sanity-checking each !included file separately was inherited from the
old scripts. It makes it messy to check that combinations of fields make
sense, e.g. to check 'const:' or 'default:' against 'type:', since those
fields might come from different files (this is handy, since it makes
sense to just add/change a 'const:' value, for example).
Drop the requirement that each !included file is a complete binding in
itself, and treat them as binding fragments instead. Only check the
final merged binding.
This also means that !included files no longer need to have a
'description:' or 'title:' (those have always been unused for !included
files), so remove those, and add comments that explain what the
fragments are for instead. That should demystify bindings a bit.
Also fix the descriptions of i2c.yaml, i2s.yaml, spi.yaml, and
uart.yaml. They're for controllers, not devices. These are copy-paste
error from the corresponding device .yaml files.
Piggyback some indentation consistency nits in binding-template.yaml.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Convert type from compound to phandle-array for various bindings that
have properties like like <FOO>-gpios, pwms, clocks,
interrupt-extended, etc. that are phandle-array's.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add two new type-checked property types 'phandles' and 'phandle-array'
to edtlib.
'phandles' is for pure lists of phandles, with no other data, like
foo = < &bar &baz ... >
'phandle-array' is for lists of phandles and (possibly) numbers, like
foo = < &bar 1 2 &baz 3 4 ... >
dt-schema also has the 'phandle-array' type.
Property.val (in edtlib) is set to an array of Device objects for the
'phandles' type.
For the 'phandle-array' type, no Property object is created. This type
is only used for type checking.
Also refactor how types that do not create a Property object
('phandle-array' and 'compound') are handled. Have _prop_val() return
None for them.
The new types are implemented with two new TYPE_PHANDLES and
TYPE_PHANDLES_AND_NUMS types at the dtlib level. There is also a new
Property.to_nodes() functions for fetching the Nodes for an array of
phandles, with type checking.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
* Add "#address-cells" and "#size-cells" to base.yaml as properties
that can exist on any node. Cleanup other bindings that inherit
from the base.yaml.
* Add "status" property with an enum of valid options.
* Add "interrupt-parent" to base.yaml. It's a phandle to the node
which is the interrupt controller for the interrupt.
* Add "interrupt-extended" to base.yaml. Provides a way to specify
an interrupt-parent and specifier in a single property. Useful if
a device has multiple interrupts in which different interrupts go
to different interrult controllers.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In most cases #<FOO>-cells should be a constant. For example in spi
controller #address-cells should be 1, and #size-cells should be 0.
Use the const attribute to specify such single known values. Add const
value to missing bindings which have cells.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a 'const' property to bindings for any properties that are expected
to have a specifi known value. For example, #address-cells for an I2C
bus should always be '1'. So we can do something like the following in
the I2C bus binding:
"#address-cells":
type: int
category: required
const: 1
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Change binding for ST sensors property 'irq-gpios' to optional for the
cases of in which its obvious from the driver that the property is
optional (there's an ifdef based on the #define
DT_INST_0_ST_LIS2DH_IRQ_GPIOS_*).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The file contained an invalid license which came from a Nordic custom
repository. Switch it to Apache 2.0.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
'child: bus:' should be in the binding for the bus node, and
'parent: bus:' in the binding for devices that appear on the bus.
The description accidentally swapped them. Fix it.
Fixes: #18821
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adding required fields to the devicetree overlay of the CAN sample as
this is often used as a reference. Also use these fields instead of the
KConfig entries.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Mark the 'reset-gpios' property as optional. It was incorrectly set
as required and its not required for the driver to function.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Property type-checking has been pretty rudimentary until now, only
checking things like the length being divisible by 4 for 'type: array',
and strings being null-terminated. In particular, no checking was done
for 'type: uint8-array', letting
jedec-id = < 0xc8 0x28 0x17 >;
slip through when
jedec-id = [ 0xc8 0x28 0x17 ];
was intended.
Fix it by adding a syntax-based type checker:
1. Add Property.type, which gives a high-level type for the property,
derived from the markers added in the previous commit.
This includes types like TYPE_EMPTY ('foo;'),
TYPE_NUM ('foo = < 3 >;'), TYPE_BYTES ('foo = [ 01 02 ];'),
TYPE_STRINGS ('foo = "bar", "baz"'),
TYPE_PHANDLE ('foo = < &bar >;'), and TYPE_COMPOUND (everything not
recognized).
See the Property.type docstring in dtlib for more info.
2. Use the high-level type in
Property.to_num()/to_string()/to_node()/etc. to verify that the
property was assigned in an expected way for the type.
If the assignment looks bad, give a helpful error:
expected property 'nums' on /foo/bar in some.dts to be assigned
with 'nums = < (number) (number) ... >', not 'nums = "oops";'
Some other related changes are included as well:
- There's a new Property.to_bytes() function that works like accessing
Property.bytes, except with an added check for the value being
assigned like 'foo = [ ... ]'.
This function solves problems like the jedec-id one.
- There's a new Property.to_path() function for fetching the
referenced node for assignments like 'foo = &node;', with type
checking. (Strings are accepted too, as long as they give the path
to an existing node.)
This function is used for /chosen and /aliases.
- A new 'type: phandle' type can now be given in bindings, for
properties that are assigned like 'foo = < &node >;'.
- Property.__str__() now displays phandles and path references as they
were written (e.g. '< &foo >' instead of '< 0x1 >', if the
allocated phandle happened to be 1).
- Property.to_num() and Property.to_nums() no longer take a 'length'
parameter, because it makes no sense with the type checking.
- The global dtlib.to_string() and dtlib.to_strings() functions were
removed, because they're not that useful.
- More tests were added, along with misc. minor cleanup in various
places.
- Probably other stuff I forgot.
The more strict type checking in dtlib indirectly makes some parts of
edtlib more strict as well (wherever Property.to_*() is used).
Fixes: #18131
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
the microchip,mcp2515 and microchip,enc28j60 bindings would hit the
following build error:
device tree error: dts/bindings/can/microchip,mcp2515.yaml (in 'reg'):
'category' from !included file overwritten
('required' replaced with 'optional')
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit includes the initial support of ARC HS Development Kit:
* hsdk soc support
* hsdk board support
* no mmu support, so no userspace
* smp support
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
This adds support for SARA-U2 modems. They have different timings on
the PWR_ON pin, don't support AT+CESQ and require a manual GPRS
connection setup.
The VINT pin is used as a more reliable and faster way to power on the
modem.
Based on work by Göran Weinholt <goran.weinholt@endian.se>
Signed-off-by: Michael Scott <mike@foundries.io>
The GIC400 is a common interrupt controller that can be used with the
Cortex A and R series processors. This patch adds basic interrupt
handling for the GIC, but does not handle multiple routing or
priorities.
Signed-off-by: Bradley Bolen <bbolen@lexmark.com>
Add "#address-cells" and "#size-cells" to the fixed-partition binding as
these are properties that may existing in the fixed-partition node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* Change pwm device bindings to include both base and pwm.yaml. This
allow for flexibility for any nodes that might not need/utilize the
base binding.
* Added pwm.yaml to a few device bindings that were missing it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a clock.yaml that clock controller bindings should inherit
from. clock.yaml defines the properties "#clock-cells" which all
clock controllers should have.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a gpio.yaml that GPIO controller bindings should inherit
from. gpio.yaml defines the properties "gpio-controller" and
"#gpio-cells" which all gpio controllers should have.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a intc.yaml that interrupt controller bindings should inherit
from. intc.yaml defines the properties "interrupt-controller" and
"#interrupt-cells" which all interrupt controllers should have.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is to support e.g. "<&adc 3>" in the device tree to create e.g.
DT_FOO_IO_CHANNELS_CONTROLLER = "ADC_0"
DT_FOO_IO_CHANNELS_INPUT = 3
Signed-off-by: Jim Paris <jim@jtan.com>
The nxp,kinetis-sim is shared by 2 SoC familes and on one of them
its not used for clocks. As such that SoC will not have a #clock-cells
property so mark it optional.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The binding for st,stm32-timers specifies #address-cells and #size-cells
as required but no dts files that have st,stm32-timers specify these
properties. Remove them from the binding.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds a driver for st7789v lcd controller, and TL019FQV01 lcd.
The bulk of the driver is based on the existing ili9340 driver.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
NRF_UICR needs to be defined for nRF9160 SoC in
nrfx_config_nrf9160.h, because it is not defined
in nrfx/hal/mdk/nrf9160.h (as it is a Secure-only
peripheral).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The snps,designware-intc.yaml and xtensa,intc.yaml define a required
property snps,num-irq-priority-bits that isn't defined in any .dts
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
With the new DT checks the dts bindings for "nxp,flexpwm" and
"nxp,imx-pwm" had old conventions that we now treat as build errors.
Additionally fix the number of #pwm-cells for "nxp,imx-pwm" to be 1.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
i.MX RT10XX processors have four eFlexPWM modules, each containing
four 2-channels PWM submodules.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
This dts binding file remained out from 0ec0c84808 commit, because
it was still in the pre-merging status.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add a new sifive,plic-1.0.0 binding that inherits from the riscv,plic0
binding. The new binding adds a required riscv,ndev property, which
gives the number of external interrupts supported.
Use the new binding for microsemi-miv.dtsi (with a value of 31 for
riscv,ndev, from http://www.actel.com/ipdocs/MiV_RV32IMAF_L1_AHB_HB.pdf)
and riscv32-fe310.dtsi (which already assigns riscv,ndev).
Also remove a spurious riscv,ndev assignment from
riscv32-litex-vexriscv.dtsi.
Also make edtlib and the old scripts/dts/ scripts replace '.' in
compatible strings with '_' when generating identifiers.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add some information that would've saved me a lot of time:
- Give an overview of how device tree nodes and bindings fit together,
with examples. Assume people might be coming at it without knowing
anything about device tree.
- Explain how 'inherits' works in more detail
- Explain what 'parent/child: bus: ...' does more concretely, and what
problem it solves
- Add more examples to show what things look like in the .dts file
- Clean up the language a bit and make things more consistent
Also fix some errors, like 'properties: compatible: ...' being wrong
(missing 'constraint:' and compatible strings in the wrong place).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add a kernel timer driver for the MEC1501 32KHz RTOS timer.
This timer is a count down 32-bit counter clocked at a fixed
32768 Hz. It features one-shot, auto-reload, and halt count down
while the Cortex-M is halted by JTAG/SWD. This driver is based
on the new Intel local APIC driver. The driver was tuned for
accuracy at small sleep values. Added a work-around for RTOS
timer restart issue. RTOS timer driver requires board ticks per
second to be 32768 if tickless operation is configured.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This was always intended to be a bytestring rather than an array, but
full support was missing. Since that has been addressed switch it to
the preferred format.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The JEDEC API defines the hardware page, sector, and block sizes.
Deprecate the Kconfig settings, remove the `erase-size-block` property,
and add `has-be32k` to indicate that 32K-byte erase is supported.
Rework the driver to use the constants instead of configured values.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Same deal as in commit eba81c6e54 ("yaml: Remove redundant document
separators"), for some newly added stuff.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
No binding has anything but 'version: 0.1', and the code in scripts/dts/
never does anything with it except print a warning if it isn't there.
It's undocumented what it means.
I suspect it's overkill if it's meant to be the binding format version.
If we'd need to tell different versions from each other, we could change
some other minor thing in the format, and it probably won't be needed.
Remove the 'version' fields from the bindings and the warning from the
scripts/dts/ scripts.
The new device tree script will give an error when unknown fields appear
in bindings.
The deletion was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i '/^\s*version: /d'
Some blank lines at the beginning of bindings were removed as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In most of the cases the fixed-clock node is not referenced by the
Zephyr code, making the label property just a burden.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
I'm guessing STM32 GPIO nodes don't generate interrupts, because I can't
find any device tree nodes with 'compatible = "st,stm32-gpio"' and an
'interrupts' property.
Remove the required 'interrupts' property from the binding. This fixes a
bunch of errors in
https://github.com/zephyrproject-rtos/zephyr/issues/17532.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The port_sel property had the category set to 'define' which isn't a
valid option. Change it to be 'required'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit makes the clock property optional (through base.yaml),
as clock reference is not used in the code.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
This commit adds a DTCM (Device Tightly Coupled Memory) section for
Cortex F7 MCUs. The Address and length is defined in the corresponding
device tree file.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Since the nxp,imx-gpio binding is shared between i.MX and i.MX-RT SoC
the 'rdc' property needs to be optional (as it doesn't make sense on the
RT SoCs).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We've removed the need for the 'generation:' property in the binding
files. Remove use in st,stm32-usb.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A number of dts bindings mark 'interrupts' as a required property when
in fact they are not for those devices. Remove the 'required' setting
and just have 'interrupts' as 'optional'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The dts that have intel,qmsi-watchdog don't sent a clock property so its
not required. Change it from being required to optional.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds a fixed clock node (representing clock driving
system bus). The added node is then referenced by peripherals requiring
information about driving clock frequency.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
These bindings override the 'category: optional' for 'clocks' from
uart.yaml with 'category: required', but none of the nodes that use the
bindings set 'clocks'.
Maybe it's a copy-paste error. Remove the 'clock' overrides.
Fixes some errors in
https://github.com/zephyrproject-rtos/zephyr/issues/17532.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These bindings !include adc.yaml, but their device tree nodes never set
'clocks':
dts/bindings/iio/adc/atmel,sam-afec.yaml
dts/bindings/iio/adc/atmel,sam0-adc.yaml
dts/bindings/iio/adc/nordic,nrf-adc.yaml
dts/bindings/iio/adc/nordic,nrf-saadc.yaml
The nodes for these bindings do set it (think it's consistent for
st,stm32-adc.yaml):
dts/bindings/iio/adc/nxp,kinetis-adc12.yaml
dts/bindings/iio/adc/st,stm32-adc.yaml
Make 'clocks' optional in adc.yaml. Maybe it should be changed to
required on some platforms (!including bindings can change 'optional' to
'required').
Fixes a bunch of errors in
https://github.com/zephyrproject-rtos/zephyr/issues/17532.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Setting it seems rare. Maybe it could be changed to required on just
some platforms (!including bindings can change 'optional' to
'required').
Fixes a bunch of errors in
https://github.com/zephyrproject-rtos/zephyr/issues/17532.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
None of the interrupt controller nodes that use this binding in the
device tree files set 'reg' (or have a unit address).
Fixes a bunch of errors in
https://github.com/zephyrproject-rtos/zephyr/issues/17532.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This patch populates "clocks" property in stm32 usb nodes
for clock related usb configuration code of each dtsi files
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The st,stm32-can binding specified several required properties that were
never set in actual .dts files and not used by the code. Remove them at
this time since they aren't being used.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We removed support for cell_string some time ago, so we have some stale
references in a number of bindings that we can remove.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Note that these appear as
properties: {erase,write}-block-size: label: ...
rather than as
properties: label: ...
I can't see anything looking at 'label' for individual properties in
bindings, so it's probably dead code. Labels are fetched from the device
tree in extract/flash.py.
Piggyback removal of some 'generation: define's and a redundant pair of
YAML document separators.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
We define "arc,num-irq-priority-bits" and "intel,num-irq-priority-bits"
as required properties in the bindings for the interrupt controllers
however we never specify these properties in any .dts files or use them
in any code.
Remove them as stale properties in the binding files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that the generation script doesn't look at the "generation" in the
YAML, we can remove it from the binding files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
uint8-array is the name for what the devicetree specification calls a
bytestring.
The original parsing code treated square brackets as equivalent to
quotes or angle brackets, failing to interpret elements as hex-encoded.
This was a bug, corrected in this patch by processing content as a
sequence of hex-encoded bytes with arbitrary whitespace.
The original generating code emitted the property as individual
elements. Replace that with generation of a single structure
initializer, which is more useful in cases where the length of a
property value may vary between nodes.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
1) dts/bindings/mmc/mmc.yaml: specifies common mmc.
2) dts/bindings/mmc/nxp,imx-usdhc.yaml: specifies
nxp usdhc module which inherits mmc.
3) dts/arm/nxp/nxp_rt.dtsi: usdhc support on RT chip.
4) boards/arm/mimxrt1050_evk/mimxrt1050_evk.dts:
usdhc slot support on mimxrt1050_evk board.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
A number of minor issues with the 'fixed-clock' support:
* Fix the #clock-cells to be 0
* Fix nxp_ke1xf.dtsi to set #clock-cells 0 and the clock reference to
only be a phandle.
* Fix the generation script to only generate what it should for a
'fixed-clock'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A few clock bindings only have a single clock cell defined, but the
binding described more than one cell.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add flash support for STM32G0X SoC series.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add support to STM LSM6DSO 6-axis IMU sensor driver.
This driver supports communication with device though both
I2C and SPI bus and both polling and drdy trigger mode.
This driver supports also the sensorhub mode with the possibility
to connect a maximum of two external devices, typically a
magnetometer and an environmental sensor, currently selected among
following devices: lis2mdl magnetometer, lps22hh or lps22hb
pressure and temperature sensors, HTS221 humidity sensor.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add support to STM LPS22HH pressure and temperature sensor.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit adds binding for clock provider with fixed frequency.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The Quark D2000 is the only x86 with an MVIC, and since support for
it has been dropped, the interrupt controller is orphaned. Removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Allow individual specification of the time quanta used for the CAN bus
propagation segment and phase segment 1.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Several bindings have an expectation of sub-nodes that describe the
actual infomation. The sub-nodes don't have any compatiable so we can't
key on that.
So we can add the concept of a sub-node to the YAML to handle cases like
'gpio-keys', 'gpio-leds', 'pwm-leds', etc..
The sub-node in the YAML is effective the "binding" params that describe
what properties should exist in the sub-node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The binding specified 2 cells for an interrupt, but in reality we only
have an IRQ number. Remove the 'pri' cell from the binding to match
what the dts files are doing.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The pinctrl property in the bindings is meaningless, lets remove it and
add a proper pinctrl property when we are ready.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
* Fix white space in phy.yaml
* Fix property name in st,stm32-usbphyc.yaml and usb-nop-xceiv.yaml to
use "#phy-cells" and not "phy-cells"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce uint8-array type for local-mac-address as we need to
distinguish it from 'array' meaning a uint32 array.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* Rename stringlist to string-array to be closer inline with upstream
dtschema definitions.
* Add string-array to the device_node.yaml.template
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
TI_HDC Driver now also supports waiting for conversion to finish instead
of waiting for GPIO interrupt.
Signed-off-by: Nikos Oikonomou <nikoikonomou92@gmail.com>
Hdc1008 driver is renamed into ti_hdc to prepare it to support all
available Texas Instruments HDC sensors (e.g. hdc1080, hdc2080).
Signed-off-by: Nikos Oikonomou <nikoikonomou92@gmail.com>
This commit adds counter driver based on RTCC module for SiLabs Gecko
SoCs.
Tested with SLWSTK6061A / BRD4250B wireless starter kit.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We've never propertly generated any pinmux info, so remove generation
from the binding yaml files for pinmux properties.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds support for the async API for SAM0 SERCOM USARTs using
DMA to drive the device.
Tested on SAMD21 with a few trivial programs and with
tests/drivers/uart/uart_async_api.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds support for the basic timer counter (TC) found on SAM0
series parts. This driver only supports running the counter
in 32 bit wide mode. Since this mode explicitly slaves the odd
counters to the even ones, only instances of the even ones are
defined.
Tested with tests/drivers/counter/counter_basic_api on SAMD21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
import linux-v5.1:Documentation/devicetree/bindings/vendor-prefixes.txt
Use vendor-prefixes.txt to check vendor prefixes
used in compatible strings and property names.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
The legacy PCI support in the DesignWare I2C driver is replaced with
the new PCIe support. The Intel Quark X1000 SoC and the galileo board
configurations are updated accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The SARA-R4 series modules from U-Blox are size-optimized LTE-M /
NB-IoT and EGPRS modules designed for low power consumption and
longer battery life.
The binding identifies the UART device, power GPIO and reset GPIO
lines.
Signed-off-by: Michael Scott <mike@foundries.io>
The label binding was missed during initial development of the
WNC-M14A2A modem. Let's add the binding so that during the
migration to a shield, we can update the DTS correctly.
Signed-off-by: Michael Scott <mike@foundries.io>
Add DTS binding files for the ARM MPU, for both ARM
MPU architecture variants, ARMv7-M and ARMv8-M.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add enum to list what values of maximum-speed are exceptable since
enum's get represented as strings in DT. This also allows us to
generate a code enum to correspond to the string.
We also introduce include/dt-bindings/usb/usb.h which is a hand coded
definition of the enum. We don't have a great way to generate this
right now, however it would be better if we did.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
MHU (Message Handling Unit) enables software to raise interrupts to
the processor cores. It is enabled in SSE 200 subsystems.
This patch aims to implement inter processor communication.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Add LiteX interrupt controller driver and bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add LiteX timer driver with bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add LiteX UART driver with bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Reduced Kconfig for counter with nRF TIMER and RTC. Added overlays
for TIMER and RTC configuration in the counter test.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add support for CLKOUT source selection and divider as found on the
NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add a new clock control driver for NXP Kinetis SoCs that have the
Peripheral Clock Controller module (PCC).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add bindings for SiFive Data Tightly-Integrated Memory.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Dts Nodes for all the GPIO portswere defined. In addition,
a new binding file was created for the gpio driver.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Expose MEC1501 5 I2C/SMB controllers
Add Microchip specific I2C device tree properties
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
All series of stm32 have at least one ADC instance and this commit adds
one ADC node to the root dts file of each soc, and also adds fixing up
mappings to them.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
The HT16K33 is a memory mapping, multifunction LED controller
driver. The controller supports up to 128 LEDs (up to 16 rows and 8
commons) and matrix key scan circuit of up to 13x3 keys.
This commit adds support for the keyscan functionality of the HT16K33.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The HT16K33 is a memory mapping, multifunction LED controller
driver. The controller supports up to 128 LEDs (up to 16 rows and 8
commons) and matrix key scan circuit of up to 13x3 keys.
This commit add support for the LED driver functionality of the
HT16K33.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This adds interrupt support to the SAM0 GPIO driver. This is heavily
inspired by @nzmichaelh work in #5715. The primary difference
from that implementation is that here the External Interrupt
Controller (EIC) is separated out into an interrupt controller driver
that is less tightly coupled to the GPIO API. Instead it implements
more of a conversion from the EIC's own odd multiplexing to a more
traditional port and pin mask IRQ-like callback. Unfortunately,
through the EIC on the SAMD2x are relatively well behaved
in terms of pin to EIC line mappings, other chips that share the
peripheral interface are not. So the EIC driver implements a
per-line lookup to the pin and port pair using definitions extracted
from the ASF headers.
The EIC driver still makes some assumptions about how it will be used:
mostly it assumes exactly one callback per port. This should be fine
as the only intended user is the GPIO driver itself.
This has been tested with some simple programs and with
tests/drivers/gpio/gpio_basic_api on a SAMD21 breakout and an
adafruit_trinket_m0 board.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds a SERCOM I2C driver for SAM0 series chips.
Tested with a SAMD21 chip on a SSD1306 display and a MLX90393
sensor. Only compile tested for SAMD20 and SAMR21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
