Adds dts bindings for the mcr20a wireless transceiver. The frdm_k64f
board supports the mcr20a via an Arduino shield, therefore the dts node
is added to the board dts. The kw2xd is a SiP and thus the mcr20a dts
node is added to the soc dts.
The networking samples using prj_frdm_k64f_mcr20a.conf have been broken
since the refactoring of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts spi bindings for the kinetis dspi controller, and updates the
k64, kw2xd, kw40z, kw41z dts nodes accordingly.
Updates the dts interrupt priorities to match the board defconfigs
(e.g., boards/arm/frdm_k64f/Kconfig.defconfig)
For k64, fixes an error in the spi1 interrupt number and adds a third
instance (spi2).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts bindings for the fxas21002 interrupt pins to all boards that
have this sensor.
The fxas21002 driver is currently only aware of one sensor interrupt
pin, therefore the routing of INT1 or INT2 to the driver is handled in
each board's dts.fixup.
The fxas21002 sample application has been broken since the refactoring
of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts bindings for the fxos8700 interrupt pins to all boards that
have this sensor. The frdm_k64f and hexiwear_k64 connect both sensor
interrupt pins to the mcu, but the frdm_kw41z connects only one.
The fxos8700 driver is currently only aware of one sensor interrupt pin,
therefore the routing of INT1 or INT2 to the driver is handled in each
board's dts.fixup.
The fxos8700 sample application has been broken since the refactoring of
the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In order to generate GPIO definition for control pin of BlueNRG module
define reset-gpio and irq-gpio in st,spbtle-rf yaml binding.
Add HAS_DTS_SPI_PINS kconfig symbol to control use of the '#define'
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that we can generate gpio info from dts lets add optional support
fot the cs-gpios property in the bus controller node. This matches the
binding spec from Linux on how cs-gpios are handled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
'cell_string' yaml attribute has been introduced in order to
help enforcement of specific string during defines generation.
This adds complexity in understanding script behavior as a black
box and create additional dependency which is not strictly required.
For node specific generation functions (pinctrl and interrupts),
this could be replaced directly by an hardcoded version
(as everyone used the same 'cell_string' anyway).
For extract_cells functions, string could be replaced by extracted
property name. As a consequence, we're now able to generate defines
for properties refering to these controllers via phandle.
For instance, in following node
spbtle-rf@0 {
compatible = "st,spbtle-rf";
reg = <0>;
reset-gpios = <&gpioa 8 0>;
};
We'll be able to generate:
#define ST_STM32_SPI_...LE_RF_0_RESET_GPIOS_CONTROLLER "GPIOA"
#define ST_STM32_SPI_...PBTLE_RF_0_RESET_GPIOS_FLAGS_0 0
#define ST_STM32_SPI_..._SPBTLE_RF_0_RESET_GPIOS_PIN_0 8
Only impact for this whole change is for NXP clocks which were the
only ones using 'cell_string' attribute with a value different than
the default one.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adds flexspi and semc memory controllers to the i.MX RT SoC. Adds
hyperflash, qspi, and sdram external memories to the mimxrt1050_evk
board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds gpio labels to all kinetis socs in preparation for refactoring the
mcux gpio driver to dts. The kl25z was missing gpio nodes altogether, so
they are added.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the imx uart driver to adapt it to the Zephyr
serial interface.
Modem mode was introduce to control it as DCE and DTE and can be
configured in the device tree:
modem-mode:
type: int
category: required
description: Set the UART Port to modem mode 0 (dce) 1 (dte)
generation: define
For now only the UART 2 was tested.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Adds a driver for SX1509B I2C GPIO chip. This driver only supports the
basic GPIO features and does not currently implement the LED driver and
keypad matrix features.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Added device tree support to the ARM SBCon I2C controller. We utilize
the compatiable "arm,versatile-i2c" the binding from Linux for the some
peripheral block.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch the SoC device tree to define a single entry per SERCOM instead
of one per mode.
Define a Device Tree binding for the SAM0 SPI and use it instead of
Kconfig for enabling / disabaling instances
Switch the Arduino Zero, Adafruit Feather M0 Basic Proto, and
Trinket M0 to use the new defintion.
Add the APA102 LED that's on the Trinket as a test.
Signed-off-by: Michael Hope <mlhx@google.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The APA102 is a RGB LED with integrated controller. LEDs can be
daisy-chained and use SPI for communication. The SPI port is
configured via Device Tree.
Tested on the Adafruit Trinket M0.
Signed-off-by: Michael Hope <mlhx@google.com>
Configure ccm size and address via dts. According to the DT
specification, the unit-address of a node must match the
first address specified in the reg property of the node.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
This commit updates the title and the description of the
ARMv6-M, ARMv7-M NVIC dts bindings, so that both the title
and the description reference the respective ARM architecture
and not the Cortex M cores.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This PR includes the required changes in order to support
conditional compilation for Armv8-M architecture. Two
variants of the Armv8-M architecture are defined:
- the Armv8-M Baseline (backwards compatible with ARMv6-M),
- the Armv8-M Mainline (backwards compatible with ARMv7-M).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Added a label for soc-nv-flash nodes. Made some updates to the
generation to maintain creating defines for properties like
erase-block-size and write-block-size so they we get both
FLASH_ERASE_BLOCK_SIZE and FLASH_${LABEL}_ERASE_BLOCK_SIZE (same for
WRITE_BLOCK_SIZE).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for AMS CCS811 Digital Gas Sensor for monitoring
indoor air quality. This sensor reports the following parameters:
1. Co2 concentration
2. VOC concentration
3. Sensor voltage
4. Sensor current
This driver only supports polling mode as of now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Pin multiplexing is a function of the PORT peripheral. This change
defines a separate pinmux device at the same address as the PORTs
themselves.
Signed-off-by: Michael Hope <mlhx@google.com>
Adds a new optional dts property to define the erase block size of a
flash device. This will be used by the mcux flash driver to implement
the flash page layout function.
The value is set for all kinetis devices to match
FSL_FEATURE_FLASH_PFLASH_BLOCK_SECTOR_SIZE.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the max30101 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxas21002 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxos8700 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add device tree support for the "nxp,kinetis-ftfa" flash controller used
on the NXP KL2X and KW4xZ SoCs.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert NXP k6x and kw2xd flash driver to use device tree to get the
flash controller name from device tree. We introduce yaml bindings for
the "nxp,kinetis-ftfe" and "nxp,kinetis-ftfl" devices.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert Atmel SAM0 flash driver to use device tree to get the flash
controller name and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce flash controller nodes for STM32 SoCs that are supported in
the flash driver. This is a precusor to converting the flash driver on
stm32 over to using device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add usart-yaml in dts.
Build fsl_lpc_usart and fsl_lpc_flexcomm in
ext/hal/nxp/mcux/drivers/Makefile.
Only polling mode is implemented in usart now. Interrupt can be added in
future.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Provide dts yaml bindings for bluetooth modules
used by 96b_carbon and disco_l475_iot1 boards.
Devices are denoted as spi-devices and inherit from
spi-device.yaml
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This was validated on the cc3220sf_launchxl board
using the Zephyr thermometer sample program
adapted to call the i2c driver directly, and fetching
samples from the on-board TMP006 temperature sensor.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Any node which needs to generate defines from DTS must have a
"compatible" property, because the corresponding "constraint" is what
extract_dts_includes.py uses to match nodes with YAML files.
There are a few YAML files in the tree that list compatible as
"optional". Fix them.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Provide dts yaml bindings for 4 sensors supported by disco_l475_iot1
board:
-hts221, lis3mdl, lps22hb and lsm6dsl
Devices are denoted as i2c-devices and, as such, inherits from
i2c-device.yaml
Signed-Off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Provide generic yaml description for i2c-devices such as sensors
New yaml binding category 'parent/child' is added.
It aims at binding two types of related node such as bus master and
bus slave.
In case of i2c-device object, parent property is 'bus' with value 'i2c'.
In the mean time, i2c node gets child property bus. Master and slave bus
values should match.
As such, 'i2c' node is bus master and 'i2c-devices' nodes are bus slaves
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
According to yaml syntaxic rules, 'properties' described in dts
bindings yaml files could be seen as 'mapping'(key/value couple),
instead of 'series' (list of single elements).
yaml 'mappings' will then be converted by yaml python library as
python 'dict' which will ease treatment (instead of current list
as were before this commit).
Same treatment is applied to 'inherits'.
script extract_dts_inlcude is updated to take change of yaml_list
structre into account. This allows some code simplification. Largest
impact is yaml_collapse function which works now allow complete
overload method on all the attributes of a yaml nodes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adds a new gpio driver for the NXP i.MX family of SoCs. Read, write,
configure, and callback API functions are all implemented.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moved yaml files to be under dts/bindings and have the bindings try
and match the linux doc device tree binding dir structure as the
canonical binding reference.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Michael Hope
