Add Nuvoton numicro series UART support, currently supports
only poll mode.
UART0 clock and pincontrol are directly configured, will be
replace when clock and gpio support is added.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Cleaned up flow control configuration. Added support for using only
cts or only rts.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add infineon XMC4 series UART support. Driver supports
only poll mode using XMCLib.
Out of 4 available UART's on SoC, only UART1 is confgired
by default in UART mode until GPIO & pinctrl support.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Adding port information for uart tx and rx pins in dts, so that it can
be more systematically retrieved in the uart driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-uart binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the GCLK, MCLK, and PM clock controllers. Add bindings
and devicetree nodes associated with these clock controllers. Also add
clock references for the SERCOM peripheral set to allow those drivers
(i2c, spi, uart) to utilize this information.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add pinctl support for the SAM UART and SAM USART devices. We update
the UART and USART bindings to have pinctrl-0 bindings that are expected
to have 2 phandles to the RX & TX pinctrl nodes.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We add sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The flexcomm peripheral on lpc socs can be configured into uart, spi,
i2c, or i2s mode. Introduce a shared device tree binding that gets
included by the more specific driver type bindings.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Extended nrf_uart driver to support TX only.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Extended nrf_uarte driver to support TX only UARTE instances.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use the device tree to assign the correct peripheral clock to each
UART/USART/LEUART. Previously, the clock identifier was determined
through the sequence number of the instantiated UART. This meant
configuring all UARTs when only one of the later UARTs was required.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Instead of
child:
bus: foo
parent:
bus: bar
, have
child-bus: foo
parent-bus: bar
'bus' is the only key that ever appears under 'child' and 'parent'.
Support the old keys for backwards compatibility, with a deprecation
warning if they're used.
Also add 'child/parent-bus' tests to the edtlib test suite. It was
untested before.
I also considered putting more stuff under 'child' and 'parent', but
there's not much point when there's just a few keys I think. Top-level
stuff is cleaner and easier to read.
I'm planning to add a 'child-binding' key a bit later (like 'sub-node',
but more flexible), and child-* is consistent with that.
Also add an unrelated test-bindings/grandchild-3.yaml that was
accidentally left out earlier.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
- hw-flow-control added to uart.yaml as it is a common feature
- cleanup other related yaml files
- change property 'category' to 'rquired' in yaml files
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
- Fixes#3981
- Implement UART Polling functions
- Implement UART Interrupt APIs
- Remove dependency on esp32_rom_uart_xxx functions
- Update Device tree with UART addresses and pin config
- Update ESP32 UART KConfig
Notes about implementation:
- Interrupts now defined as a local macros, and should be removed
later on, when interrupts for esp32 are supported in dts
- Threshold interrupts are used for TX/RX
- Reseting FIFOs using _RST bit will corrupt FIFO of UART2 when used for
UART1 and vice-versa, so a generic way is used for all three UARTs
- Old Silicon rev is not supported
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Instead of
properties:
compatible:
constraint: "foo"
, just have
compatible: "foo"
at the top level of the binding.
For backwards compatibility, the old 'properties: compatible: ...' form
is still accepted for now, and is treated the same as a single-element
'compatible:'.
The old syntax was inspired by dt-schema (though it isn't
dt-schema-compatible), which is in turn a thin wrapper around
json-schema (the idea is to transform .dts files into YAML and then
verify them).
Maybe the idea was to gradually switch the syntax over to dt-schema and
then be able to use unmodified dt-schema bindings, but dt-schema is
really a different kind of tool (a completely standalone linter), and
works very differently from our stuff (see schemas/dt-core.yaml in the
dt-schema repo to get an idea of just how differently).
Better to keep it simple.
This commit also piggybacks some clarifications to the binding template
re. '#cells:'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fixes an upcoming error:
device tree error: 'hw-flow-control' appears in /soc/uart@40028000
in nrf52840_pca10056.dts.pre.tmp, but is not declared in
'properties:' in .../dts/bindings/serial/nordic,nrf-uarte.yaml
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 'category: required/optional' setting for properties is just a
yes/no thing. Using a boolean makes it clearer, so have
'required: true/false' instead.
Print a clear error when 'category:' is used:
edtlib.EDTError: please put 'required: true' instead of 'category:
required' in 'properties: foo: ...' in
test-bindings/sub-node-parent.yaml - 'category' has been removed
The old scripts in scripts/dts/ ignore this setting, and only print a
warning if 'category: required' in an inherited binding is changed to
'category: optional'. Remove that code, since the new scripts already
have the same check.
The replacement was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i \
-e 's/category:\s*required/required: true/' \
-e 's/category:\s*optional/required: false/'
dts/binding-template.yaml is updated as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Sanity-checking each !included file separately was inherited from the
old scripts. It makes it messy to check that combinations of fields make
sense, e.g. to check 'const:' or 'default:' against 'type:', since those
fields might come from different files (this is handy, since it makes
sense to just add/change a 'const:' value, for example).
Drop the requirement that each !included file is a complete binding in
itself, and treat them as binding fragments instead. Only check the
final merged binding.
This also means that !included files no longer need to have a
'description:' or 'title:' (those have always been unused for !included
files), so remove those, and add comments that explain what the
fragments are for instead. That should demystify bindings a bit.
Also fix the descriptions of i2c.yaml, i2s.yaml, spi.yaml, and
uart.yaml. They're for controllers, not devices. These are copy-paste
error from the corresponding device .yaml files.
Piggyback some indentation consistency nits in binding-template.yaml.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
No binding has anything but 'version: 0.1', and the code in scripts/dts/
never does anything with it except print a warning if it isn't there.
It's undocumented what it means.
I suspect it's overkill if it's meant to be the binding format version.
If we'd need to tell different versions from each other, we could change
some other minor thing in the format, and it probably won't be needed.
Remove the 'version' fields from the bindings and the warning from the
scripts/dts/ scripts.
The new device tree script will give an error when unknown fields appear
in bindings.
The deletion was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i '/^\s*version: /d'
Some blank lines at the beginning of bindings were removed as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
A number of dts bindings mark 'interrupts' as a required property when
in fact they are not for those devices. Remove the 'required' setting
and just have 'interrupts' as 'optional'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These bindings override the 'category: optional' for 'clocks' from
uart.yaml with 'category: required', but none of the nodes that use the
bindings set 'clocks'.
Maybe it's a copy-paste error. Remove the 'clock' overrides.
Fixes some errors in
https://github.com/zephyrproject-rtos/zephyr/issues/17532.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Now that the generation script doesn't look at the "generation" in the
YAML, we can remove it from the binding files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The pinctrl property in the bindings is meaningless, lets remove it and
add a proper pinctrl property when we are ready.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We've never propertly generated any pinmux info, so remove generation
from the binding yaml files for pinmux properties.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds support for the async API for SAM0 SERCOM USARTs using
DMA to drive the device.
Tested on SAMD21 with a few trivial programs and with
tests/drivers/uart/uart_async_api.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add LiteX UART driver with bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Allows to enable initial RTS/CTS hardware flow control
in the dts.
Co-authored-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
A parallel PCI implementation ("pcie") is added with features for PCIe.
In particular, message-signaled interrupts (MSI) are supported, which
are essential to the use of any non-trivial PCIe device.
The NS16550 UART driver is modified to use pcie.
pcie is a complete replacement for the old PCI support ("pci"). It is
smaller, by an order of magnitude, and cleaner. Both pci and pcie can
(and do) coexist in the same builds, but the intent is to rework any
existing drivers that depend on pci and ultimately remove pci entirely.
This patch is large, but things in mirror are smaller than they appear.
Most of the modified files are configuration-related, and are changed
only slightly to accommodate the modified UART driver.
Deficiencies:
64-bit support is minimal. The code works fine with 64-bit capable
devices, but will not cooperate with MMIO regions (or MSI targets) that
have high bits set. This is not needed on any current boards, and is
unlikely to be needed in the future. Only superficial changes would
be required if we change our minds.
The method specifying PCI endpoints in devicetree is somewhat kludgey.
The "right" way would be to hang PCI devices off a topological tree;
while this would be more aesthetically pleasing, I don't think it's
worth the effort, given our non-standard use of devicetree.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
After commit 'scripts/dts: Never ignore properties in
generate_node_defines()', pointless entries for 'interrupt-names'
properties show up in generated_dts_board.conf and
generated_dts_board_fixups.h, because many bindings specify
'generate: define' for 'interrupt-names'.
If 'generation: define' is taken as "generate #define's for this
particular property", then only the 'interrupts' property ought to have
'generation: define'. Having it on both 'interrupts' and
'interrupt-names' makes you wonder what it would mean to only have it on
one of them.
Things get a bit confusing since 'interrupt-names' is still used when
determining the macro names generated for 'interrupts', but it's
probably best to have 'generation: define' work in a consistent way
still (and never be a no-op).
Remove 'generation: define' from all 'interrupt-names' bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Support for HW flow control was recently enabled in the NXP MCUX
HAL layer. Let's add a DTS binding definition for "hw-flow-control".
The MCUX uart driver shim can use this to enable HW flow control.
Signed-off-by: Michael Scott <mike@foundries.io>
