With addition of flash_get_parameters API call, it is needed to provide
support for the API to flash drivers.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The st,stm32l0-flash-controller did not have a binding, add one for it.
Also made a comment in stm32l0.dtsi that the driver doesn't currently
support this controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Most JEDEC NOR flash devices uses not only typical SPI mode
(MISO,MOSI,SCK and CS), but also QSPI mode (IO0,IO1,IO2,IO3,SCK and CS).
QSPI mode uses more data lines and as a result provide higher
throughput. If this were not enough, Nordic chips provide
hardware acceleration for read/write/erase functions, what
gives significant performance boost.
It does a lot of things "behind the scene", i.e when user has written
some data to the flash and would like to read them back, it has to wait
until the flash is ready by reading WIP bit in Status Register.
This driver does it automatically.
Signed-off-by: Kamil Lazowski <Kamil.Lazowski@nordicsemi.no>
Merge all the information into 'description:' and remove 'title:'.
Gets rid of a deprecation warning.
See commit 2934ee2cda ("dts: bindings: Remove 'title:' and put all info.
into 'description:'").
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The amount of lock regions differs between different sam0 MCUs.
saml10: 2
saml11: 4
samd2x: 16
saml2x: 16
samd5x: 32
ASF does not provide a definition for this, so create a new one
in dts.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Instead of
properties:
compatible:
constraint: "foo"
, just have
compatible: "foo"
at the top level of the binding.
For backwards compatibility, the old 'properties: compatible: ...' form
is still accepted for now, and is treated the same as a single-element
'compatible:'.
The old syntax was inspired by dt-schema (though it isn't
dt-schema-compatible), which is in turn a thin wrapper around
json-schema (the idea is to transform .dts files into YAML and then
verify them).
Maybe the idea was to gradually switch the syntax over to dt-schema and
then be able to use unmodified dt-schema bindings, but dt-schema is
really a different kind of tool (a completely standalone linter), and
works very differently from our stuff (see schemas/dt-core.yaml in the
dt-schema repo to get an idea of just how differently).
Better to keep it simple.
This commit also piggybacks some clarifications to the binding template
re. '#cells:'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 'category: required/optional' setting for properties is just a
yes/no thing. Using a boolean makes it clearer, so have
'required: true/false' instead.
Print a clear error when 'category:' is used:
edtlib.EDTError: please put 'required: true' instead of 'category:
required' in 'properties: foo: ...' in
test-bindings/sub-node-parent.yaml - 'category' has been removed
The old scripts in scripts/dts/ ignore this setting, and only print a
warning if 'category: required' in an inherited binding is changed to
'category: optional'. Remove that code, since the new scripts already
have the same check.
The replacement was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i \
-e 's/category:\s*required/required: true/' \
-e 's/category:\s*optional/required: false/'
dts/binding-template.yaml is updated as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Sanity-checking each !included file separately was inherited from the
old scripts. It makes it messy to check that combinations of fields make
sense, e.g. to check 'const:' or 'default:' against 'type:', since those
fields might come from different files (this is handy, since it makes
sense to just add/change a 'const:' value, for example).
Drop the requirement that each !included file is a complete binding in
itself, and treat them as binding fragments instead. Only check the
final merged binding.
This also means that !included files no longer need to have a
'description:' or 'title:' (those have always been unused for !included
files), so remove those, and add comments that explain what the
fragments are for instead. That should demystify bindings a bit.
Also fix the descriptions of i2c.yaml, i2s.yaml, spi.yaml, and
uart.yaml. They're for controllers, not devices. These are copy-paste
error from the corresponding device .yaml files.
Piggyback some indentation consistency nits in binding-template.yaml.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Same deal as in commit eba81c6e54 ("yaml: Remove redundant document
separators"), for some newly added stuff.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
No binding has anything but 'version: 0.1', and the code in scripts/dts/
never does anything with it except print a warning if it isn't there.
It's undocumented what it means.
I suspect it's overkill if it's meant to be the binding format version.
If we'd need to tell different versions from each other, we could change
some other minor thing in the format, and it probably won't be needed.
Remove the 'version' fields from the bindings and the warning from the
scripts/dts/ scripts.
The new device tree script will give an error when unknown fields appear
in bindings.
The deletion was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i '/^\s*version: /d'
Some blank lines at the beginning of bindings were removed as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Now that the generation script doesn't look at the "generation" in the
YAML, we can remove it from the binding files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add flash support for STM32G0X SoC series.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com
Signed-off-by: Francois Ramu <francois.ramu@st.com>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds a flash driver implementation that writes to RAM and
exports statistics through stats.h. It can be used to simulate flash
memory for testing purposes.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
After commit 'scripts/dts: Never ignore properties in
generate_node_defines()', pointless entries for 'interrupt-names'
properties show up in generated_dts_board.conf and
generated_dts_board_fixups.h, because many bindings specify
'generate: define' for 'interrupt-names'.
If 'generation: define' is taken as "generate #define's for this
particular property", then only the 'interrupts' property ought to have
'generation: define'. Having it on both 'interrupts' and
'interrupt-names' makes you wonder what it would mean to only have it on
one of them.
Things get a bit confusing since 'interrupt-names' is still used when
determining the macro names generated for 'interrupts', but it's
probably best to have 'generation: define' work in a consistent way
still (and never be a no-op).
Remove 'generation: define' from all 'interrupt-names' bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This patch adds a flash driver for the STM32F7x series, inspired from
the STM32F4x one. It has been tested on the STM32F723, but should also
work on other SoCs of the family.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch adds a flash driver for the Atmel SAM E70 SoC. The driver has
been kept simple by considering that the flash is only composed of 8-KiB
blocks. Indeed an area at the beginning of the flash might be erased
with a smaller granularity, and the other blocks can also be erased with
a higher granularity. It also only handles the global read/write
protection, not the 128-KiB lock regions. A write error is returned if
a region is locked.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The 'id' field was never used and tended to just have the compat of the
node. Lets remove it and removed some code in extract_dts_includes.py
related to it. Added a warning if 'id' is set in a yaml so we can
remove it going forward.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added initial support and created the corresponding device tree part for
building PSoC6 SoC as part of Zephyr.
Signed-off-by: Nazar Chornenkyy <nazar.chornenkyy@cypress.com>
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
Flash controller-node for stm32f2 based SoCs was missing basic
properties such as compatible, labeln reg and interrupts.
Fix this and add matching yaml binding file;
Fixes#10057
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
All flash controllers have a mandatory compatible property.
Add it to the generic binding that is included by all.
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
Add device tree support for the "nxp,kinetis-ftfa" flash controller used
on the NXP KL2X and KW4xZ SoCs.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert NXP k6x and kw2xd flash driver to use device tree to get the
flash controller name from device tree. We introduce yaml bindings for
the "nxp,kinetis-ftfe" and "nxp,kinetis-ftfl" devices.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert Atmel SAM0 flash driver to use device tree to get the flash
controller name and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce flash controller nodes for STM32 SoCs that are supported in
the flash driver. This is a precusor to converting the flash driver on
stm32 over to using device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
