Add PL330 dma driver support, this driver
- supports 32 bit memory to memory operation
- supports 36 bit memory to memory operation
under a config flag DMA_64BIT
- supports secure channel
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
tested on mimxrt1060_evt
MEMORY_NOCACHE is needed
test on frdmk64f
special test slot need configure with
CONFIG_DMA_TEST_SLOT_START
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
This patch prepares the dma and introduces the dmamux on soc series
which supports this feature for memory/periph transfers.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
There is no such thing as CAVS DMA IP block, the DMA IP block found on
CAVS based chips is made with DesignWare one.
This will help to centralize DW based DMA device into one driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This commit adds driver support for DMA on f0/f1/f2/f3/f4/l0/l4
series stm32.
Notice due to some bugs, this is currently not working with f7.
There are two kinds of IP blocks are used across these stm32, one is the
one that has been used on F2/F4/F7 series, and the other one is the one
that has been used on F0/F1/F3/L0/L4 series.
Memory to memory transfer is only supported on the second DMA on
F2/F4 with 'st,mem2mem' to be declared in dts.
This driver depends on k_malloc to allocate memory for stream instances,
so CONFIG_HEAP_MEM_POOL_SIZE must be big enough to hold them.
Common parts of the driver are in dma_stm32.c and SoC related parts are
implemented in dma_stm32_v*.c.
This driver has been tested on multiple nucleo boards, including
NUCLEO_F091RC/F103RB/F207ZG/F302R8/F401RE/L073RZ/L476RG with the
loop_transfer and chan_blen_transfer test cases.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
This adds support for the SAM0 DMA Controller (DMAC). Chained
transfer are not currently implemented.
Tested with tests/drivers/dma/loop_transfer and custom modifications
to that test using three parallel reloading channels. Also tested
with a trivial program that did memory->serial.
Signed-off-by: Michael Hope <mlhx@google.com>
[hageman@inthat.cloud: Rebased and updated commit message]
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Add dma driver for Nios-II Modular Scatter-Gather DMA soft IP.
This driver relies upon the Altera HAL msgdma driver for all
the dma core register programming and interrupt handling.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Introduce the Intel CAVS DMA. This is based out of the DesignWare
DMA IP but the register offset and bits have been changed in some
cases. However, the fundamental definition for the register field
has not been changed. Hence the registers begin with "DW_" to
indicate the Designware origin.
This driver currently supports the single block mode and linked list
multi-block mode. Scatter-Gather is not supported.
Change-Id: I33a8ed5141d9236167de50e14d3d407e95d6f553
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
As per current policy of requiring supervisor mode to register
callbacks, dma_config() is omitted.
A note added about checking the channel ID for start/stop, current
implementations already do this but best make it explicitly
documented.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Added DMA (XDMAC) driver for Atmel SAM MCU family. The driver provides
private DMA API to be used by the SAM family device drivers. Public
DMA API to be used by user space programs is currently missing.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1609
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Michael Hope
