This reverts commit 1da0a9eebd.
The workaround caused a severe performance penalty, and only worked
for USB packets of 4-15 bytes in length (16+ byte packets weren't
subject to the hardware bug). Single-byte packets (very common for
cdc_acm serial port transfers) would still be duplicated sometimes.
The upcoming DMA implementation does not share the performance
penalty, and also is not subject to the bug for those sizes of packets
(though it DOES still have a problem with single-byte packets!).
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
There is no particular reason this spot in usb_dw_tx() cannot be
reached by racing threads on the same endpoint, though existing API
usage in the tree is all unithreaded. The FIFO state read at the top
of the function must still be true at the bottom or else the packet
byte count will be corrupt.
Also, as described in an existing comment, the databook has some
scary-sounding warnings about access to the registers during FIFO
operations, even if they "should" be on separate endpoints and
unrelated.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
If NET_L2_IEEE802154 and NET_IPV6 are enabled:
- NET_6LO is enabled
- NET_L2_IEEE802154_FRAGMENT is enabled
Thus removing setting this config options to yes where applicable.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This rework commit 77b8f5c1f6
Comparing it to BT IPSP is a the wrong comparison: BT IPSP does specify
6lo/ipv6 for it to work. Whereas 802.15.4 does not.
Instead of selecting 6lo from 802.15.4's Kconfig, let's do the reverse
way. If the user enabled 802.15.4 and IPv6 as well (to which 6lo
depends on), then 6lo is enabled by default as using IPv6 on 15.4
without it does not make much sense.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Issue a error message, if the _mcr20a_read_reg fails.
Do not execute SPI burst read/write if the buffer is too small.
Unlock mutex if set_pan_id, set_short_addr or set_ieee_addr
fail.
Force abort of the sequence when the higher level changes the channel
even though a T or TR sequence is in progress.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Describe details and usecase for using this function. This follows
earlier updates for macros used to define buffers used by this
function (in 09b967366).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Intention of CONFIG_BOOT_DELAY is to delay booting of system for certain
time. Currently it is only delaying start of _main thread as delay is
created using k_sleep. This leads to putting _main thread into timeout
queue and continue kernel boot. This is causing some of undesirable
effects in some of test Automation usecase.
This patch changes k_sleep to k_busy_wait which result in delay in OS
boot instead of delaying start of _main.
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add board configuration, dts and pinmux, based on
arm/stm32f4_disco and arm/nucleo_f411re boards.
Error free tests are executed on eval board with the following
sample applications:
- hello_world
- blinky-sample
- button-sample
- console_echo_sample
- console_getchar_sample
Signed-off-by: Jose F. Fernandez <jffernandez@fenix-es.com>
checkpatch returns the following errors:
"ERROR:COMPLEX_MACRO: Macros with complex values
should be enclosed in parentheses"
Let's fix all of them.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The functionality of the shell scripts for flashing and debugging has
now been replaced by zephyr_flash_debug.py. Remove the legacy scripts
as part of transitioning all of this to Python.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Some of the flashing scripts try to be clever about picking unused
ports. That's convenient for the user, so add a helper class to
runner.core to accomplish similar ends portably.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Factor the classes which do the work into a new "runner" package. This
package has a core module where ZephyrBinaryRunner and common helpers
will live, and one file per subclass / runner front-end.
The top-level script, zephyr_flash_debug.py, still exists, but just
delegates its work to the core.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Though it isn't used by any in-tree Makefile.boards, looking at the
RIOT OS build system, this is meant to be split along lexical
boundaries defined by the shell, not just whitespace.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Several debugging scripts run setsid before executing a server
process, then run GDB with SIGINT ignored.
Relying on setsid is not portable. Add a popen_ignore_int() helper
that provides a portable alternative, and provide a generic
run_server_and_client() in ZephyrBinaryRunner which uses it to
abstract the pattern.
Subsequent patches will use this to implement the 'debug' command.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Just as was previously done for flashing, invoke zephyr_flash_debug.py
from the build system debug and debugserver targets by default. The
Python script will fall back on the corresponding shell script if it
doesn't have its own implementation.
The shell script can be used instead, just as with flashing, by
setting USE_ZEPHYR_FLASH_DEBUG_SHELL to any nonempty value.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Replace the 'flash' method with a 'run' method, which takes a command
to run (flash, debug, or debugserver).
Rename the classes involved appropriately, and generalize the factory
interfaces as needed.
Add documentation and theory of ops.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This is similar to the LPD8806 sample, but uses the WS2812 driver
instead. The app configuration is a bit more finicky, so try to
provide helpful references. This could be made more beginner-friendly
with the addition of timing diagrams, etc., but this should be enough
for an experienced developer to use.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This sample displays the colors red, green, and blue on consecutive
LEDs in an LED strip, moving the starting point where red begins
further down the strip at each time step. The color band wraps around
to the beginning when it reaches the end.
Since this is the first application in samples/drivers to have
documentation, add samples/drivers/drivers.rst as well, and include it
in the top-level toctree from samples/samples.rst.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
The WS2812 LED driver IC has a one-wire interface which encodes bit
values as pulse widths.
The ICs themselves are basically shift registers. Roughly speaking, a
"short" pulse shifts in a zero bit, a "long" pulse shifts in a one
bit, and an inter-pulse gap exceeding a reset time threshold causes a
pixel to latch the shifted-in color values. Each chip has an output
pin for daisy chaining. Refer to the chip datsheets and comments in
Kconfig.ws2812 for more details.
To meet timing without hogging the core, this driver generates pulses
using SPI. To work, this requires the MOSI line to stay low between
SPI frames, and for inter-frame delays to be less than the reset pulse
time.
There are other ways do it (PWM + DMA on some SoCs, GPIO bit-banging
if no other tasks need the core), but this is a reasonably
general-purpose implementation.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
LPD880x (e.g. LPD8803, LPD8806) devices are LED driver ICs which can
be controlled via a reduced SPI interface (clock and data only), and
support daisy chaining.
Add an led_strip driver for these devices.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This API covers drivers for strips, or strings, of individually
addressable LEDs. Both RGB and grayscale LED strip drivers can be
implemented within these APIs.
The API only provides for updating the entire strip, since not all
strips support updating individual LEDs without affecting the others.
Subsequent patches will add individual driver support.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
All ztest_* apis now support format specifier which will
evetually help to pass variable arguments to ztest assert
apis in different test cases while showing error messages.
Signed-off-by: Punit Vara <punit.vara@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove CONFIG_NET_L2_ETHERNET, as it's automatically set by the
board. This effectively makes prj_frdm_k64f.conf fairly portable,
e.g. the same config can be used for frdm_kw41z whcih uses 802.15.4
connectivity instead.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This ensures DW_apb_i2c correctly transmits the slave address (7 or
10 bit) based on ic_10bitaddr_master when configured in master mode.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
The ic_tar and ic_sar were earlier set to 9 bits but now its
corrected to consider 10 bits.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
When the header file is located in the same directory as the source
file it is better to use a relative quote-include, e.g.
than a system include like
Avoiding the use of system includes in these cases is beneficial
because;
* The source code will be easier to build because there will be fewer
system include paths.
* It is easier for a user to determine where a quote-include header
file is located than where a system include is located.
* You are less likely to encounter aliasing issues if the list of
system include paths is minimized.
Authors:
Anas Nashif
Sebastian Bøe
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Recent commit fb7f6cfa97 ("net: lib: http: Fix invalid pointer
body_start") introduced logic to reset the response body_start pointer
when the response buffer was reused.
This check needs to be fixed so that it doesn't arbitrarily change
body_start when not needed.
The problem with the current check can be demonstrated by not setting
a response callback for request which generates a large response
spanning multiple packets.
In this case body_start is still valid (not reusing the response buffer
because there is no callback set), but it will be changed when the 2nd
packet is received and the "at" marker is located at the head of the
new packet (!= response_buffer).
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This header doesn't need arch/cpu.h for anything in it, remove
to ease dependency inclusion dependencies.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Fix init_group bit clearing in _k_thread_group_leave()
Fix _k_object_uninit calling order. Though the order won't
make much difference in this case it is always good to destroy
or uninitialize in the reverse order of the object creation or
initialization.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>