This patch changes the way the custom linker function works. It uses
names instead of numbers to denote the name of the file and applies
the correct LINKER_PASS variable for the final linker pass.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
It makes no sense to set the restart condition flag on a first message
and some i2c bus drivers (like the stm32 v1 driver) actually reject
them by returning an error from i2c_transfer().
This patch fixes that by using i2c_burst_read() in tmp112_reg_read()
instead. For consistency, tmp112_reg_write() is also changed to use
i2c_burst_write().
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
I have been using this the TMP112 driver with success with a TMP102
connected to to nucleo-f411re board (via I2C1 using PB8/9).
According to the datasheets, both devices are both driver and pin
compatible although the TMP102 is less accurate.
This temperature sensor is not a thermopile sensor type as stated in
comments.
This patch updates that help info
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
Write protection is currently not supported by the mcux flash
driver. This prevents it from working with the DFU subsystem, which
checks the error codes from the write protect routine. Hack it for now
with a semaphore.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
A lot of improvements have made it into Kconfiglib since we introduced
it into Zephyr. This rebases our 2 Zephyr-specific commits into the
latest Kconfiglib upstream.
Origin: https://github.com/zephyrproject-rtos/Kconfiglib/tree/zephyr
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace seldom occurrences of FLASH_DRIVER_NAME by equivalent
and commonly used FLASH_DEV_NAME.
Fixes#5919.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add sample application for AMS CCS811 digital gas sensor driver.
This application fetches Co2, VOC, Voltage and Current readings
from the sensor and prints it on serial console continuously.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for AMS CCS811 Digital Gas Sensor for monitoring
indoor air quality. This sensor reports the following parameters:
1. Co2 concentration
2. VOC concentration
3. Sensor voltage
4. Sensor current
This driver only supports polling mode as of now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
CCS811 digital gas sensor supports the following channels:
1. Co2 Channel
2. VOC Channel
3. Voltage Channel
4. Current Channel
Add support for the those in API.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Some ARMv6-M Cortex-M0+-based SOCs have VTOR register
and can relocate vector table just as ARMv7-M ones.
Vector table relocation path should be choosed
by VTOR presence, not by arch.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Make it easy to override HTTP host/port/path. Print URL which we
request and make few other adjustment to the output for clarity.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
In preparation towards a refactored controller, rename the
old radio_*_is_enabled() function to ll_*_is_enabled().
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
CONFIG_I2C_NRF5_GPIO_SDA_PIN and CONFIG_I2C_NRF5_GPIO_SCL_PIN are
replaced with port specific versions. Board defconfigs relying on the
original names are updated. The driver is also modified to pass the
configure values to registers.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
This patch changes the manner in which we collect DTS overlay files so
that they comply with the same approach taken for configuration fragment
files (.conf).
Additionally it also documents the usage of those files in the
Application Developer Guide.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Check the fault reason against the expected value.
This is presently architecture-specific, and possibly
reflects a bug on ARM (all faults end up with reason 0,
even though ARM does define a separate value for Oops).
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Previously we were handling any fault during test execution as
a pass condition. Explicitly indicate when a fault is expected
and fail the test if we encounter an unexpected fault.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
SENSOR_CHAN_DISTANCE is now in meters. Print value in meters, as
double, this requires printf() and CONFIG_STDOUT_CONSOLE. This is
similar to how other sensor samples have it.
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Most of sensor channels defined by Zephyr use the main, unscaled
SI unit. We also have SENSOR_CHAN_ALTITUDE which is defined in
meters. So, it only makes sense to define distance in meters too
The only driver supporting SENSOR_CHAN_DISTANCE as of now is
vl53l0x.c, which was updated accordingly. Also, update doc links
in the driver based on the review comment.
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
We need to allocate extra memory region for the hash function
that the gperf generates. The linker will need to maintain
the same location counter between multiple linker stages. Reserving
memory will help in maintaing correct location counters between
multiple stages. The required memory varies with optimization level.
In order to keep the size of the compiled object consistent,
the kobject_hash.c is always compiled with -Os.
fixes#5226
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Fix the controller implementation to handle Control PDUs
with invalid lengths by responding with Unknown Response
PDU.
Fixes LL.TS.5.0.2 conformance tests:
LL/PAC/SLA/BI-01-C [Control PDUs with Invalid Length from
Master]
LL/PAC/MAS/BI-01-C [Control PDUs with Invalid Length from
Slave]
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
