Update mbedTLS commit along with the following fixes:
* Fix naming inconsistencies in some cipher modes, to match core mbedTLS
configs
* Add Kconfig to enable CTR cipher mode
Fixes#22421
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
During communication initialisation, the IMSI of the inserted SIM
card is evaluated to determine the APN. This is done by comparing
the first 5 characters of the IMSI to a list of known providers.
The list can be given in Kconfig.
To enable this functionality, set following bool in Kconfig:
MODEM_UBLOX_SARA_AUTODETECT_APN
To set a list of providers, set following string:
MODEM_UBLOX_SARA_AUTODETECT_APN_PROFILES
If the provider can not be found in the list, the APN given in
following entry is used as a fallback:
MODEM_UBLOX_SARA_R4_APN
Signed-off-by: Hans Wilmers <hans@wilmers.no>
The modem type (Sara R410 or Sara U201) is detected automatically after
hardware initialisation of the modem. Further initialisation and
functionality is then chosen depending on the detected modem type.
To enable this functionality, set following bool in Kconfig:
MODEM_UBLOX_SARA_AUTODETECT_VARIANT
Signed-off-by: Hans Wilmers <hans@wilmers.no>
Many chips have only one serial port. When the serial port is occupied
by other devices, there is a lack of a console to output debugging
information. Semihosting can provide a console. The disadvantage of
semihosting is that a debugger must be connected, so it can only be
used for online debugging.
Signed-off-by: ZhongYao Luo <LuoZhongYao@gmail.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add initial support for Decawave DW1000
IEEE 802.15.4-2011 UWB transceiver.
Driver has basic functionality. Additional functions such
as reading out timestamps and delayed TX were implemented
for test purposes, but also require support in the 802154
subsystem.
Register, sub-register, and defaults defines in the file
ieee802154_dw1000_regs.h are taken from the Decawave's
DW1000 driver for the Mynewt OS.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add support for ADC on H7 series. Note that ADC1 and ADC2 share the same
register set, so it is added as "adc1_2".
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Like stm32 L4 does,
when the STM32WBx SoC goes into STOP mode, the SPI device is disabled.
This cause the pins to not be drived anymore (i.e. they are floating)
except through their pull-up or pull-down.
From the logical point of view, the NSS pin is held high by a pull-up
so it's not a problem if the other pins are floating. However those pins
are floating input for the slaves, which increase their power
consumption.
The solution is to hold the state of the pins through a pull-up or a
pull-down. This is already done for the NSS and MOSI pins, but not for
SCK. Fix that by using pull-down on the SCK pin the same way it is
already done for the MOSI pin.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Convert i2s_sam_ssc driver to utilize devicetree. We replace Kconfig
options for specifying the DMA configuration (channel, DMA device name)
with getting that from devicetree. We also get pincfg from devicetree,
however we still have Kconfig sybmols to specify if the RF or RK pin is
enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert sam_xdmac driver to utilize devicetree. As part of the
controller binding we specify that dmas should contain a channel and the
perid for the DMA transaction.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The conversion in 9b096f40b6 left out a
few tidbits that were not converted properly. Complete the conversion
properly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Remove semicolon between instance invocations of DT_FOREACH_IMPL_ and
thus DT_INST_FOREACH. This provides more flexibility to the user. This
requires we fixup in tree users to add semicolon where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
MCHP Soc operation uses clear-on-write register for interrupt
status, read-OR-write operation may clear interrupts unintentional.
Fixes#24464
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Attached Flexcomm SPI driver to the main clock used by the core.
This means setting the SPI clock the same value as the core clock.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
This fixes some cases where an integer timeout received as a parameter
was not converted to a timeout before being used in standard API.
Changes to the POSIX library were not included as that's being
reworked in a separate PR.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The DS3231 is an I2C real-time clock with internal temperature
compensated oscillator, maintaining civil time to 1 s precision with
nominal 2 ppm accuracy from 0-40 Cel.
The basic functionality is exposed as a counter that is always running
at 1 Hz. Much more functionality is exposed as driver-specific API,
including the ability to translate between the time scale of the DS3231
and the time scale of the Zephyr uptime clock. This allows correlation
of events in the system clock to UTC, TAI, or whatever time scale is
used to maintain the DS3231.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add a driver that can handle several instances of AT45 family chips,
which are enabled by specifying DT nodes for them with the "compatible"
property set to "atmel,at45" and other required properties like JEDEC
ID, chip capacity, block and page size etc. configured accordingly.
The driver is only capable of using "power of 2" binary page sizes in
those chips and at initialization configures them to work in that mode
(unless it is already done).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
referring the ARM's Systick driver, we did the following improvements:
* use 31 bits of 32-bit counter to avoid the rare but possible
overflow of elapsed(). If 32 bits val are used, elpased() may
return a wrong value. then wrong HW cycles.
* two ways to update the correct cycles
- through systick timer irq
- when systick timer irq cann't be handled because of irq
locked/disabled, call z_timer_cycle_get_32->elapsed to update
the correct cylces. no more than one counter-wrap is allowed.
* if elapsed() is not called too long (more than one counter-wrap) from
systick tiemr irq or from z_timer_cycle_get_32. The lost of HW cycles
is unavoidable.
* some detailed discussion can be found in #24332
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Fix use of DT_HAS_DRV_INST which does not exist.
Use DT_HAS_NODE_STATUS_OKAY(DT_DRV_INST(n)) instead.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Provide basic commands that are useful when testing a LoRa
radio. Currently, the shell supports:
> lora conf ...
> lora send ...
> lora recv ...
> lora test_cw ...
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Add an API to transmit a continuous wave at a fixed frequency. This
functionality is useful to test the radio in a lab setup.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Add basic driver for GIC V3 interrupt controller.
This implementation supports
- distributor, re-distributor and cpu interface initialization
- configuration and handling of SPI, PPI and SGI.
- V2 Legacy mode is not supported and uses system interface.
Current implementation supports GIC secure state only.
All interrupts are routed to Secure EL1 as 'irq' by configuring
them as Group1 Secure.
TODO:
- MPIDR based affinity routing setting.
- percpu redistributor probe
- message based SPI and SGI generation api
- EL1NS support. Legacy mode support.
- LPI/ITS is not supported.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Port the I2S and DMIC drivers to the new timeout API so that they do
not need to enable legacy timeouts.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As we phase out per instance Kconfig symbols convert to utilize
DT_DRV_INST to initialize CAN instances.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As we phase out per instance Kconfig symbols convert to utilize
DT_DRV_INST to initialize CAN instances.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a build-time assert to check that the configured SHM_SIZE
does not exceed the memory allocated as shared memory. USe DT
to extract the shared memory size.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The sam0 has a page size of 64 bytes, making it incompatible with
the nvs driver that specifies a maximum write block size of
32 bytes. When CONFIG_SOC_FLASH_SAM0_EMULATE_BYTE_PAGES is set,
it should report a write block size of 1 byte, which is compatible
with nvs.
Signed-off-by: Adam Serbinski <aserbinski@gmail.com>
The dpd-wake-sequence has a value that is an array of three integers,
which was formerly indexed by a suffix on the property name. This was
updated to new accessors but failed to separate the index from the
property name. Update the access idiom.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert to using DT_INST_LABEL() in the dma driver and convert dma users
to use the DMA property macros to get the dma controller name. We make
the assumption in the drivers that there is a single DMA controller
instance.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Had an extra comma between macro and macro usage that casued the
following compile error:
adc_shell.c:477:22: error: expected expression before ',' token
Easy fix to remove trailing comma in ADC_SHELL_COMMAND
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clean up as we wish to move away from using these Kconfig settings.
Also removing them from the boards' default config.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Make drivers multi-instance wherever possible using DT_INST_FOREACH.
This allows removing DT_HAS_DRV_INST in favor of making drivers just
do the right thing regardless of how many instances there are.
There are a few exceptions:
- SoC drivers which use CMake input files (like i2c_dw.c) or otherwise
would require more time to convert than I have at the moment. For the
sake of expediency, just inline the DT_HAS_DRV_INST expansion for
now in these cases.
- SoC drivers which are explicitly single-instance (like the nRF SAADC
driver). Again for the sake of expediency, drop a BUILD_ASSERT in
those cases to make sure the assumption that all supported SoCs have
at most one available instance is valid, failing fast otherwise.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The TPM (Timer/PWM Module) is a 2- to 8-channel timer which supports
input capture, output compare, and the generation of PWM signals to
control electric motor and power management applications.
This patch adds the driver and the binding necessary for instantiating
the driver. The work is based on the RV32M1 driver for TPM done by
Henrik Brix Andersen. A later patch will enable this driver to be used
for the KW41Z SoC, if PWM support is requested.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
* Define USB driver for base stm32wb device.
* Enable USB for the nucleo_wb55rg board.
* Properly initialize USB power + clock for the platform.
Signed-off-by: Pete Johanson <peter@peterjohanson.com>
Use the endop bit in the status register (instead of using a k_sleep)
to wait until the current shub operation is completed.
Please note that the recent changes to k_sleep() API was also
breaking the compilation.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert all canbus related API/samples/tests/subsys
to the new timeout API with k_timeout_t.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
We can utilize the devicetree macros to determine which instances to
enable. This will allow us to phase out the per instance Kconfig
symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This reverts commit 90cc723e65.
Using `DMAC_CHCTRLA_TRIGACT_BLOCK` breaks SERCOM UART peripheral DMA
operations (DMA-based asynchronous UART transmit operation only sends
the first byte and does not proceed any further).
The `DMAC_CHCTRLA_TRIGACT_BURST` with `DMAC_CHCTRLA_BURSTLEN(0)` is a
special case utilising the "internal FIFO", according to the datasheet
(see DS60001507E; 22.6.2.8), and should always be specified for
peripheral data transfer operations.
Also it is worth noting that Atmel and other third-party drivers use
the aforementioned "internal FIFO" configuration for peripheral data
transfers as well.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The channel direction for a V1 DMA is not allowed to be memory to memory
and there is a check in place for this. However, the check is being
performed on the stream prior to actually configuring the stream. This
results in the check always failing regardless of the channel direction.
The check has been modified to be performed on the incoming
configuration.
Signed-off-by: Abe Kohandel <abe@electronshepherds.com>
Fix I2C bit banging REPEATED START condition function by ensuring both
SDA and SCL are high before generating the REPEATED START.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Fix I2C bit banging STOP condition function to not create a stray
START condition if SDA is high on entry. Instead, set SDA to LOW
before generating the STOP condition.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This patch prepares the dma and introduces the dmamux on soc series
which supports this feature for memory/periph transfers.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fix some wrong assignments for SPI2 and add all other alternative
functions for USART, I2C, SPI and CAN according to STM32F091VC
datasheet, which is at the top end of this series.
https://www.st.com/resource/en/datasheet/stm32f091vc.pdf
Signed-off-by: Martin Jäger <martin@libre.solar>
Following other drivers, Kconfig based instances are now entirely
removed. In order to do this change, PWM nodes in board DT files have
been given a pwm{N} label so that both:
- DT API checks such as #if DT_HAS_NODE(DT_NODELABEL(pwmN)) can be
used (N being PWM instance number).
- DT references can be written as pwms = <&pwmN x y>; instead of
pwms = <&{/soc/timers@XXXXXXXX/pwm} x y>;
This approach is also used on the Linux Kernel.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Convert the GPIO bit banging I2C controller driver to use devicetree
bindings for configuring instances.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The optimisation in `spi_sam0_fast_txrx()` is broken, loading
two bytes into the `DATA` register in rapid succession will lose
one byte.
This can be observed by running `tests/drivers/spi/spi_loopback`.
The test will get stuck in `spi_sam0_fast_txrx()` forever waiting
for the final byte.
Undo this small optimisation and only load the next byte into the
`DATA` register after the response has been received.
This fixes `tests/drivers/spi/spi_loopback`.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Move to using NODELABEL references to enable driver instances for
PWM0..3. This will allow us to remove per-instance PWM Kconfig symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The PS/2 driver was enabled with a single mouse and kb brand.
However, when plugging other mice brands, the interaction between the
driver and the device(mouse) was broken. A delay after inhibithing
the PS/2 instance helped the internal FSM to start the TX process.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Get rid of legacy timeout API and move to new timeout API for LoRa.
This involves changes to API, SX1276 driver and sample application.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
The LoRa APIs are expected to undergo some change as the usecase get's
increased. So let's mark it as experimental until the APIs got
stabililized.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
The RTC/Counter implementation doesn't fit for the upcoming LoRaWAN
as most of the Counter drivers in Zephyr works with 1s granularity
which is not enough for LoRaWAN stack. So, k_timer calls are used in
place of Counter's alarm and k_uptime_get() APIs are used in place of
Counter's time keeping.
While at it, lets also fixup the broken alarm implementation.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reworked sam_gmac driver to get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from soc_pinmap.h that are no longer needed due to
getting all that information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The DMA callback function now controls the tx or rx buffers
and reload dma in case of multiple trnasfer before the transfer ends
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Enable dma operations with or w/o a dmamux on STM32
for SPI periph/memory operations.
Use the pi dma client with dma macros
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patch is disabling the dma channel before reloading
source and dest for memory and peripheral addresses
Then the channel is enabled to re-launch the transfer.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace having dts_fixup.h files define DT_ADC_{0..2}_NAME with using
the new devicetree.h macros. We test to see what driver compat is
enabled via DT_HAS_COMPAT and set DT_DRV_COMPAT to that compat. Than we
can utilize the DT_INST_LABEL() macro to extract the name of the device.
We also replace the Kconfig ADC_{0..2} symbols with DT_HAS_DRV_INST.
This will allow us to remove those Kconfig symbols as this was the only
usage.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We want to limit DT_ prefix to macros from devicetree.h and generation.
So rename DT_USB* to just USB*.
Also fixup how USB_MAXIMUM_SPEED was defined. We should only define it
if the property exists.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Substitute integral constants where call sites passed named constants
that have timeout values as arguments to parameters that expect
millisecond durations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Do not assume in the SoC level device trees that NXP Kinetis FlexTimer
nodes will always be configured as PWM. Instead, configure FlexTimer
nodes for PWM at the board level for NXP Kinetis boards.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The goto instruction was removed when adding the RX thread.
While still working, this clearly break the clean handling of
error cases.
Re-instantiate the goto instruction.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
ipm_busy is meant to be used as mutex on transport layer accesses.
Due to wrong configuration on rx_thread, imp_busy was a no-op.
Fix this.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We want to limit DT_ prefix to macros from devicetree.h and generation.
So rename DT_LIS2DH_INT* to just LIS2DH_INT*.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We want to limit DT_ prefix to macros from devicetree.h and generation.
So rename DT_INST_AT2X* to just INST_DT_AT2X*.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We want to limit DT_ prefix to macros from devicetree.h and generation.
So rename DT_INST_MCP320X* to just INST_DT_MCP320X*.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On cortex M4, AHB clock is equal to SystemCoreClock
On Cortex M7, AHB clock is equal to SystemCoreClock/HPRE
By the way, D1CPRE is of no use when starting from SystemCoreColck.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
TCP contexts are referenced twice,
once for the app and once for the stack.
Since TCP stack is not used for offload,
unref a second time to release the context.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks from devicetree.
We add a property ('calib-offset') for the SAM{D,E}5x family of SoCs
that is the bit position offset from ADC0 BIASCOMP in the NVM Software
Calibration Area Mapping. For ADC0 this is typically 0 and for ADC1
this will be 14.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the missing prefix z_ required to make the ESP32 version override
the weak implementation.
General practice in ESP32 seems to be to use the MAC address, so
extract that in its canonical byte order.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new path access helpers to avoid hard-coding devicetree paths
in Kconfig, which is a bit messy.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove logging of individual threads spread out throughout the
bluetooth subsystem. The stacks can be analysed by enabling the
following options.
CONFIG_THREAD_ANALYZER=y
CONFIG_THREAD_ANALYZER_AUTO=y
CONFIG_THREAD_ANALYZER_RUN_UNLOCKED=y
Optional:
CONFIG_THREAD_NAME=y
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
The pinmux_mchp_xec is also being updated since it's using DT
from GPIO.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add a Kconfig option that allows user to set any necessary config
using management interface before interface be operational. A use
case is set the EUI-64 address from an external EEPROM by the
NET_REQUEST_IEEE802154_SET_EXT_ADDR command. After all configs
are done net_if_up() can be invoked to bring interface up.
Fixes#23193.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add local-mac-address on DT and enable it on rf2xx driver. If user
define local-mac-address this value will be used as default mac address.
Otherwise driver automatically add a random mac address.
On application level user can change default mac address using net_mgmt
command with NET_REQUEST_IEEE802154_SET_EXT_ADDR parameter defined on
include/net/ieee802154_mgmt.h header.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fasten events handling by unloading callback treatment.
A RX thread is created. IPM RX events are dumped in a FIFO
which is processed in the thread context.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options and dts fixups for GPIO instances.
A side-effect to using DT_INST_FOREACH is that GPIO ports A0 and A3
are now enabled, whereas they were originally disabled by default as
an optimization.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Changing more of DT_* prefixed macros that refer to instances to use
DT_INST macros in GPIO, I2C and UART drivers.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Convert various DT_DTCM_* macros to use DT_CHOSEN(zephyr_dtcm) and
associated macros from devicetree.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert pinmux driver to use nodelabels to get references to devicetree
nodes using the new devicetree.h macros.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert gpio driver to use nodelabels to get references to devicetree
nodes using the new devicetree.h macros.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks from devicetree. Move the prescaler setting
from Kconfig to devicetree as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_L2_SRAM_* to just L2_SRAM_* and set it using new DT macros.
Do something similar for DT_LP_SRAM_* renamed to LP_SRAM_*
Updated the intel_gna driver as it used the DT_L2_SRAM_* defines.
This change also lets us remove dts_fixup.h on intel_s1000 and
intel_apl_adsp SoCs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-spi binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-i2c binding for dma to replace the dma property with
proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked spi_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use NODELABEL macros rather than DT_INST as this driver is so far
limited to support of LPTIM1 instance.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert the driver to use the new dt macros. As part of this change we
remove a bunch of defines that happened in dts_fixup.h that didn't
belong there. Some of these should be converted to devicetree
properties at some point.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When notifying the handler that GPIO interrupt has occurred
pass only pins that are associated with this handler.
Fixes: #24634
Signed-off-by: Pawel Dunaj <pawel.dunaj@nordicsemi.no>
Tests were failing as they were looking for an alias which didn't exist
Also, because some code in kscan_handlers.c wasn't compilable
Signed-off-by: Mark Olsson <mark@markolsson.se>
Replace DT_CPU_CLOCK_FREQUENCY with a PATH based reference to cpu@0
(DT_PATH(cpus, cpu_0)) and than getting the clock_frequency property:
DT_CPU_CLOCK_FREQUENCY -> DT_PROP(DT_PATH(cpus, cpu_0), clock_frequency)
This lets us remove DT_CPU_CLOCK_FREQUENCY from dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options for UART instances.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Adding port information for uart tx and rx pins in dts, so that it can
be more systematically retrieved in the uart driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Convert driver to use DT_INST_ defines. As part of this conversion we
remove the Kconfig options for per GPIO controller enables and instead
get that information from device tree. This means we now disable each
GPIO controller by default in the DTS and have each board dts enable the
GPIO controller ports it needs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Although it is not clearly specified in the UART API, this function
is supposed to return 0 when the TX interrupt is disabled, regardless
of whether anything could fit into the TX buffer or not (this can be
concluded from looking at implementations of several samples and tests
present in the tree, also almost all UART drivers are implemented this
way).
The problem in the uart_nrfx_uarte driver case is that the flag that
allows generation of the TX interrupt is not cleared directly in the
uart_irq_tx_disable() function but this clearing is deferred to the
end of the current transmission, in case one is in progress, and hence
it is done in the interrupt handler. Consequently, when the interrupt
handler is not entered between calls to uart_irq_tx_disable() and
uart_irq_tx_ready() (e.g. when both functions are called in a loop
executed in the interrupt context), the latter may return an invalid
value.
Fix this problem by additionally checking if the TX interrupt was
requested to be disabled, not only if it is already disabled in
hardware.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Espi bus interrupts need to re-enable after espi reset to get
all espi bus and vw signal interrupts.
Signed-off-by: Venkataramana Kotakonda <venkataramana.kotakonda@intel.com>
Epsi slave need to respond with an OOB_RST_ACK for OOB_RST_WARN sent by
master during host reset. Enable interrupt for OOB_RST_WARN to receive
signal changes and respond with ACK.
Signed-off-by: Venkataramana Kotakonda <venkataramana.kotakonda@intel.com>
The check of the SF_TXDATA_FULL flag is only done on the register
address and not on the actual register content.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked adc_sam_afec driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
