Convert older DT_INST_ macro use in atmel sam0 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in microchip drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in sifive drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in esp32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in silab drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in cc13xx_cc26xx drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
It was observed that leaving the pin type configured for i2c for SDA
and SCL results in higher power consumption during standby. So we are
resetting the pin type when bringing the i2c into low power mode, and
setting it back to the correct type when exiting low power mode.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Add a dependency on the I2C resource in the TI Power module,
reconfigure the peripheral upon CPU exiting standby, and add
support for device PM.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Calling device_set_power_state() with DEVICE_PM_SUSPEND_STATE then
DEVICE_PM_OFF_STATE creates an assert in nrf driver
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Update hal_nordic's revision, so that NRFX_ASSERT uses __ASSERT_NO_MSG
directly, not through the assert macro that comes from from libc,
as the definition of the latter might be different when some specific
libc version is used, and this could generate troubles.
Replace also uses of assert() with __ASSERT_NO_MSG() in nrfx driver
shims that use this macro without including the corresponding header
file (i.e. that implicitly rely on assert.h being included from
nrfx_glue.h, which is no longer the case).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit fixes the multiple SERCOM interrupt handling for the SAM
D5x and E5x devices by replacing the obsolete device tree symbol with
the new `DT_INST` symbol.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit fixes an incorrect declaration of the buffer_size member
of the i2c_eeprom_slave_config struct.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
This API will be deprecated in favor of the new API that clearly
specifies whether it works on logical or physical levels.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
- Updates gpio driver and device tree files to the new GPIO Config flags
- Implements the new port_* APIs
- Update I2C and PWM Drivers to use new GPIO config
- Add esp32.overlay to gpio_basic_api test
- refactor convert_int_type, regs struct
- remove config_polarity
- add kConfig notes
Tests:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_basic_api
- tests/drivers/gpio/gpio_api_1pin
Board:
- esp32 DevKitC V4
Note about interrupts:
The ESP32 requires specifying a CPU interrupt to be used for GPIO
interrupt signals. CPU interrupts can be either level or edge (or
special) triggered, but not both.
Please check gpio/Kconfig.esp32 for more info.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
I2C interrupts usage should be the preferred way. This commit
enables them by default in the STM32 I2C driver itself.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Same deal as in commit 677f1e6 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for a newly-introduced stuff.
Also clean up headers to be consistent with recent cleanups.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
...instead of kconfig.
This provides a bit more flexibility in defining driver
instances. Also, since the DTS defines 5 I2C controllers,
the driver code is extended to cover all 5 if the controllers
are enabled.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Refactors the mcux lpi2c driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpi2c driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt and kinetis
socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This adds I2C bitbang driver for LiteX SoC builder with its bindings.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
According to the I2C spec, the SDA signal must be
stable as long as the SCL signal is high (which
means it can change only when clock is low).
This commit reworks clock signal handling
in such a way that all reads are done
when SCL is high and SDA is stable.
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
MCHP I2C spec recommends that for repeated start update control register
De-assert ACK in preparation for NACK to end transfer.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
The init macro used outdated spellings for the instance-specific
properties, resulting in build warnings when I2C was enabled.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This patch tests the return code when calling clock_control_get_rate
and completes the issue #20503 seen on watchdog
[Coverity CID :205655]
Fixes#20503
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The I2C peripheral should be configured using the CPU clock frequency
and not the system clock frequency. This used to be fine because they
were the same before #19232, but now that the system clock is
RTC-based (which has a different frequency), we can no longer make
that assumption.
Fixes#20480
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Update the I2C slave EEPROM driver to match the new atmel,at24 device
tree binding, where the size of the EEPROM is specified in bytes.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Unused since commit f3f8f96842 ("tests: i2c_slave_spi: update to
proposed DT compatible naming").
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Now that everything is DT based for I2C drivers we can rename the
CONFIG_I2C_[0..5]_NAME define to DT_I2C_[0..5]_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all I2C drivers utilize DTS we can select HAS_DTS_I2C in a
common place and don't need to do it per driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Defining a symbol with 'menuconfig' just tells the menuconfig to display
any dependent symbols that immediately follow it in a separate menu.
'menuconfig' has no effect on symbol values.
Making a symbol that doesn't have any dependent symbols after it a
'menuconfig' should be avoided, because then you end up with an empty
menu, which is shown as e.g.
[*] Enable foo ---
This is how it would be shown if there were children but they all
happened to be invisible as well.
With a regular 'config', it turns into
[*] Enable foo
Change all pointless 'menuconfig's to 'config's.
See the section on 'menuconfig' on the Kconfig - Tips and Best Practices
page as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The base_address in the device configuration is used as a handle
to access an entity in memory. In C, we call that a 'pointer'.
Also in C, (versus, say, PL/M) we name these pointer things after
what they point not ('regs') not what they are ('base address').
Thus, we change the member to a pointer type and change its name.
This makes it compile cleanly regardless of machine pointer size,
while also cutting down on a bunch of casting noise.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
In master trasmitter mode AutoEndMode is
always disabled, so we need to send STOP
manually if NACK is received.
Fixes#19059
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In the main Addr handler code the F1 workaround was used.
Add compile time swith depending on SOC family.
So workaround is not afffecting F2/F4 families.
Signed-off-by: Pavlo Hamov <pavlo_hamov@jabil.com>
These calls are buildable on common sanitycheck platforms, but are not
invoked at runtime in any tests accessible to CI. The changes are
mostly mechanical, so the risk is low, but this commit is separated
from the main API change to allow for more careful review.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Use a consistent way of enabling particular instances of peripherals
in nrfx drivers through options defined in modules/Kconfig.nordic,
to make the usage of nrfx drivers in Zephyr, especially the ones for
which there are no Zephyr driver shims (yet), easier.
Jira: NCSDK-2744
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Adjust I2C timeouts after k_busy_wait precision has increased.
Report error on first I2C message failure.
Send STOP condition when error is detected.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Consistently place C++ use of extern "C" after all include directives,
within the negative branch of _ASMLANGUAGE if used.
Only updated in headers that already had support for drivers built with
a C++ compiler.
The spi_dw.h file defines macros to declare functions, then uses them
within a file that may have out-of-tree overrides. In this case we
leave the including file extern "C" active for backward compatibility.
Background from issue #17997:
Declarations that use C linkage should be placed within extern "C"
so the language linkage is correct when the header is included by
a C++ compiler.
Similarly #include directives should be outside the extern "C" to
ensure the language-specific default linkage is applied to any
declarations provided by the included header.
See: https://en.cppreference.com/w/cpp/language/language_linkage
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add support of I2C. Add I2C5 configuration for the
arduino connector support.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@linaro.org>
We generated a define for each instance to convey its existance of the
form:
#define DT_<COMPAT>_<INSTANCE> 1
However we renamed all other instance defines to be of the form
DT_INST_<INSTANCE>_<FOO>. To make things consistent we now generate a
define of the form:
#define DT_INST_<INSTANCE>_<COMPAT> 1
We also now deprecate the DT_<COMPAT>_<INSTANCE> form and fixup all uses
to use the new form.
Fixes: #17650
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make use of the new flag introduced in nrfx v1.7.2 that suspends
transfers, in order to properly handle scattered I2C transactions,
especially to perform i2c_burst_write() in the way expected by
display drivers, i.e. as a continuous transaction on the bus,
without the repeated START between its two parts.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Sometimes i2c operation does not return in a while loop.
Fix this by adding timeout to the i2c driver.
Fixes: #12261
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
The i2c_cc32xx driver used system clock frequency
as a base for I2C clock frequency calculation.
This commit corrects that by obtaining the needed value from DTS.
Please note, that for I2C devices the clock-frequency property
specifies SCK frequency, instead of frequency of the clock driving
peripheral. To solve that problem, a new property was added.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
On some SoCs the frequency of the system clock is obtained at run time
as the exact configuration of the hardware is not known at compile time.
On such platforms using CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC define
directly introduces timing errors.
This commit replaces CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC by the call to
inline function sys_clock_hw_cycles_per_sec() which always returns
correct frequency of the system clock.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
TWI and TWIM used single static variable for multiple instances.
It would cause problems in case of multiple instances of peripheral.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2c.h to drivers/i2c.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move dma.h to drivers/dma.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move clock_control.h to drivers/clock_control.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move power.h to power/power.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move internal and architecture specific headers from include/drivers to
subfolder for interrupt_controller:
include/drivers/interrupt_controller/
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The defines related to IRQ priority don't exist and aren't used. So
just pass 0 to IRQ_CONNECT for the priority field.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The defines should have had a _0 on them, now that we generate the
proper defines, fixup the cases that used that old scheme.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Found a few annoying typos and figured I better run script and
fix anything it can find, here are the results...
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Per guidelines, all statements should have braces around them. We do not
have a CI check for this, so a few went in unnoticed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Kconfig symbols I2C_STM32_V1 and I2C_STM32_V2 depends on SoC reference
and user should not have the possibility to choose one or the other.
Remove prompt on these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
