Print the name of the discovered toolchain as well as the variable
used to initialize it.
This is nice to know when doing remote support, since users will
sometimes misconfigure their toolchain and not know what that means.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The XCC toolchain may come with Clang front-end depending on
how it's built. Currently, the only SoC/board using XCC is
the intel_s1000_crb and its XCC toolchain comes with Clang
3.9.0 which has a lot better support for C99 and C++11 than
the portion based on GCC 4.2 (which does not even support
C++11). So this change attempts to use the Clang portion
instead of GCC if the Clang executable exists.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This forms the foundation for the abstraction of the binary tools,
where the following steps are taken:
- Move binary tool resolving, such as objcopy, objdump, readelf and
so forth, out of compiler definitions and place in a dedicated binary
tools folder with the binary tools supplier as subfolder, similar to
the compiler and linker directories.
- Create binary tool sets, gnu, host-gnu and llvm.
- Each toolchain selects the required set of binary tools by setting
BINTOOLS via its generic.cmake as it also does for compiler and linker.
The intent here is to abstract Zephyr's dependence on toolchains,
thus allowing for easier porting to other, perhaps commercial,
toolchains and/or usecases.
No functional change expected.
Signed-off-by: Danny Oerndrup <daor@demant.com>
Ensure that xcc is at parity with gcc and clang by inferring missing
definitions based on those that it already provides.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
The LINKER variable is introduced to follow the same logic and flow as
the existing COMPILER variable: That is, each TOOLCHAIN is responsible
for choosing COMPILER and LINKER.
Currently, Zephyr's build system is hardcoded for GNU ld.
Reflect this in LINKER by letting all existing toolchains use GNU ld.
No functional change expected.
This is motivated by the wish to abstract Zephyr's usage of toolchains,
permitting non-intrusive porting to other (commercial) toolchains.
Signed-off-by: Mark Ruvald Pedersen <mped@oticon.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Contrary to all other toolchains, the xcc toolchain had a hardocded
installation path. Replace this with XTENSA_TOOLCHAIN_PATH so users can
install in different locations.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
XCC is based on xcc, but is nothing like gcc and his many differences.
Instead of ifdeffing the gcc code with Xcc specifics, maintain it
standalone.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
newlib is not supported with this toolchain, so mark it as such and
filter tests based on the variable defined in the toolchain file.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Split up the toolchain configuration into two phases, generic and
target. The 'generic' phase configures the toolchain just enough to be
able to preprocess DT files. The 'target' phase completes the
configuration with target-specific configuration.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
