Remove DT_ADC_{0..2}_NAME from dts_fixup.h, if this casues the
dts_fixup.h file to be empty we remove the file as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked sam_gmac driver to get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from soc_pinmap.h that are no longer needed due to
getting all that information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the `devicetree.h` header inclusion in the Atmel SAM-
family SoC header files, as required by the ARM SoC conventions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the `devicetree.h` header inclusion in the Atmel SAM0-
family SoC header files, as required by the ARM SoC conventions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Enable the driver for the Kinetis Digital-to-Analog (DAC) modules
present in the NXP Kinetis K6x SoC series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Enable the driver for the Kinetis Digital-to-Analog (DAC32) module
present in the NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Remove dts_fixup.h files that are needed anymore, remove defines that
are used, and replace defines with new DT macros.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move defines for _RAM_ADDR, _RAM_SIZE, _ROM_ADDR, and _ROM_ADDR into
the linker.ld and thus remove dts_fixup.h. We rework to use
DT_REG_ADDR and DT_REG_SIZE on DT_CHOSEN(zephyr_sram) and
DT_CHOSEN(zephyr_flash).
Also fixup use of _RAM_ADDR/_RAM_SIZE in newlib/libc-hooks.c.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove dts_fixup.h files that are not used (empty) or the defines aren't
used anymore and thus can be removed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert linker scripts and arc_mpu_regions.c setup to use new
devicetree.h macros to extract the base address and size of the various
memory regions (DDR, SRAM, FLASH, DCCM, ICCM). We also remove the
scaling up and down since DT_REG_SIZE() returns the value in bytes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework x86 linker scripts to use DT_REG_ADDR/DT_REG_SIZE on
DT_CHOSEN(zephyr_sram) and DT_CHOSEN(zephyr_flash). As part of this
we remove the dts_fixup.h. Using DT_REG_SIZE means we don't have to
adjust the sizes by 1024.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove dts_fixup.h files that are needed anymore, remove defines that
are used, and replace defines with new DT macros.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_SNPS_ARCEM_0_CLOCK_FREQUENCY with a PATH based reference
to cpu@0 (DT_PATH(cpus, cpu_0)) and than getting the clock_frequency
property:
DT_SNPS_ARCEM_0_CLOCK_FREQUENCY ->
DT_PROP(DT_PATH(cpus, cpu_0), clock_frequency)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert from DT_MMIO_SRAM_10000000_BASE_ADDRESS to
DT_REG_ADDR(DT_NODELABEL(ddr0)) and similar for
DT_MMIO_SRAM_10000000_SIZE to DT_REG_SIZE().
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Complete STM32 conversion to new DT macros by removing
remaining occurences of DT_ST_STM32_ADC_FOO_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When we converted the GPIO driver to the new GPIO API we didn't update
the MMU mapping defines. Use the macros from devicetree.h and
nodelabel's to get the register base address and sizes for the GPIO
blocks.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Complete STM32 conversion to new DT macros by removing
remaining occurences of DT_ST_STM32_ADC_FOO_LABEL.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
During devicetree macro changes, LPSRAM_BOOT_VECTOR_ADDR
pointed to another macro which was renamed to a non-existent
one. Fix it so that SMP builds again.
Fixes#24720
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Rework the atom/linker.ld to match how ia32/linker.ld works with regards
to how PHYS_LOAD_ADDR & PHYS_RAM_ADDR are set based on CONFIG_XIP and
from which DT_PHYS_{RAM,LOAD}_ADDR defines. We update the minnowboard
dts and atom.dtsi files to keep in sync with this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ocram and sdram regions to use new macro DT_REG_ADDR() and
DT_REG_SIZE() with DT_NODELABEL to determine the various memories size
and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert the code for setting the clock IP source of the various IPs
present in the NXP KE1xF SoC series to the new DT API.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
The pinmux_mchp_xec is also being updated since it's using DT
from GPIO.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Replace DT_ARM_CORTEX_*_0_CLOCK_FREQUENCY with a PATH based reference
to cpu@0 (DT_PATH(cpus, cpu_0)) and than getting the clock_frequency
property:
DT_ARM_CORTEX_*_CLOCK_FREQUENCY ->
DT_PROP(DT_PATH(cpus, cpu_0), clock_frequency)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit renames the Kconfig `FLOAT` symbol to `FPU`, since this
symbol only indicates that the hardware Floating Point Unit (FPU) is
used and does not imply and/or indicate the general availability of
toolchain-level floating point support (i.e. this symbol is not
selected when building for an FPU-less platform that supports floating
point operations through the toolchain-provided software floating point
library).
Moreover, given that the symbol that indicates the availability of FPU
is named `CPU_HAS_FPU`, it only makes sense to use "FPU" in the name of
the symbol that enables the FPU.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options and dts fixups for GPIO instances.
A side-effect to using DT_INST_FOREACH is that GPIO ports A0 and A3
are now enabled, whereas they were originally disabled by default as
an optimization.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Rename DT_L2_SRAM_* to just L2_SRAM_* and set it using new DT macros.
Do something similar for DT_LP_SRAM_* renamed to LP_SRAM_*
Updated the intel_gna driver as it used the DT_L2_SRAM_* defines.
This change also lets us remove dts_fixup.h on intel_s1000 and
intel_apl_adsp SoCs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked spi_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added ATMEL_SAM_DT_NUM_PINS macro which will return the number of pins
to initialize for "pinctrl-0" devicetree property.
Added ATMEL_SAM_DT_PINS macro which will create an array initializer
with all the pins associated with "pinctrl-0" devicetree property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add wdt0 node labels for all watchdogs. Keep the existing wdt node
labels in place for backwards compatibility.
Add a wdt1 node to the nRF5340 application core .dtsi, but leave it
disabled. Leave the wdt node's label set to "WDT" on this core for
backwards compatibility also, in case any users are getting it with a
string literal instead of asking the devicetree. This can be changed
later after this round of watchdog changes has been shaken out and
tested more.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Convert the driver to use the new dt macros. As part of this change we
remove a bunch of defines that happened in dts_fixup.h that didn't
belong there. Some of these should be converted to devicetree
properties at some point.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SAM E54 series SoCs include a single-precision FPU; therefore, the
`CPU_HAS_FPU` symbol should be selected.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The SAM E53 series SoCs include a single-precision FPU; therefore, the
`CPU_HAS_FPU` symbol should be selected.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The SAM E51 series SoCs include a single-precision FPU; therefore, the
`CPU_HAS_FPU` symbol should be selected.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The SAM D51 series SoCs include a single-precision FPU; therefore, the
`CPU_HAS_FPU` symbol should be selected.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The SAM D51, E51 and E53 SoC series Kconfig files were missing the
`ARM` architecture symbol selection.
This symbol must be selected at the SoC level; otherwise, build will
fail because the symbol is not selected by anything and other ARM-
specific configurations depend on it.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Replace DT_CPU_CLOCK_FREQUENCY with a PATH based reference to cpu@0
(DT_PATH(cpus, cpu_0)) and than getting the clock_frequency property:
DT_CPU_CLOCK_FREQUENCY -> DT_PROP(DT_PATH(cpus, cpu_0), clock_frequency)
This lets us remove DT_CPU_CLOCK_FREQUENCY from dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change DT_GPIO_GECKO_SWO_LOCATION to use new DT_INST and DT_PROP macros
and remove defining it in dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the FPGA GPIO init to use the devicetree.h macros instead of
dts_fixup.h. This allows us to remove dts_fixup.h on mps2 based
platforms.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert old DT defines of the form DT_ARM_SCC_BASE_ADDRESS to
DT_REG_ADDR(DT_INST(0, arm_scc)). This allows us to remove dts_fixup.h
on musca boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked adc_sam_afec driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. We also remove
defines in dts_fixup.h as they are no longer needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. We update one
sample app to use a nodelabel reference. We also remove defines in
dts_fixup.h as they are no longer needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a common header for SAM0 drivers to use to extract data from
devicetree. The initial set of macros are for get the MCLK A*MASK
register address for clock enablement and a set of macros for use with
DMA to get the channel and trigger source or 0xff if there is no dmas
property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_CPU_CLOCK_FREQUENCY with a PATH based reference to cpu@0
(DT_PATH(cpus, cpu_0)) and than getting the clock_frequency property:
DT_CPU_CLOCK_FREQUENCY -> DT_PROP(DT_PATH(cpus, cpu_0), clock_frequency)
This lets us remove DT_CPU_CLOCK_FREQUENCY from dts_fixup.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In order for IO pins to work correctly after waking up from shutdown
mode, we need to unlatch them given they were automatically latched
when Power_shutdown() was invoked.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The DT_I2S_* defines can be removed as the driver is now utilizing the
new dt macros that don't require these defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. This allows us to
also remove dts_fixup.h that are no longer used.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace macros of the form DT_CAVS_ICTL_x_IRQ with new dt form macro
DT_IRQN(DT_INST(x, intel_cavs_intc))
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace various drivers and soc code that use DT_CAVS_ICTL_BASE_ADDR
with DT_REG_ADDR(DT_NODELABEL(cavs0)).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked i2c_sam_twi driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked i2c_sam_twi driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. We can remove
various defines from dts_fixup.h now as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. We remove the
aliases and use nodelabel instead in the soc_gpio.h to determine the
label for the specific gpio controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. This allows us to
also remove dts_fixup.h that are no longer used.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert from using dts_fixup.h based macros to DT_INST macro. This lets
us remove the dependancy on dts_fixup.h for this driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage. We also remove dts_fixup.h defines that
are no longer needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert from using dts_fixup.h based macros to DT_INST macro. This
lets us remove the dependancy on dts_fixup.h for this driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked usart_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked uart_sam driver to utilize new DT_INST macros as part of this
rework we also now get pin ctrl/mux configuration information from the
device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a set of macros that will create a struct soc_gpio_pin
initialization based on data extracted from device tree. This should
allow replacing the static data in soc_pinmap.h with data coming from
devicetree instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
