Perform OTP override when selecting 32Khz internal oscillator
to ensure 32KHz is enabled.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Use hex file for flash command, instead of elf file. This allows to
flash signed firmware, which is not available in elf format, by
specifying --hex-file command line argument.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far zephyr.elf file was hardcoded in cmake files. Remove it from
there and use cfg.elf_file from python, which can be overwritten by
specifying --elf-file command line option.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add new tests that make sure that sendmsg() works when using
connected UDP socket and when not setting msghdr destination
address.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the UDP socket is connected, then allow the user to leave
out the remote address in msghdr struct.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We want to use the riscv64 toolchain across the board for RISC-V. That
requires a min of the 0.10.2 SDK, so bump the version before we make
that change.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit includes tweaks in several tests, so
that the tests can be passing on ARM QEMU targets,
mps2_an385 and mps2_an521 with Qemu 4.x release.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Update SDK version to 0.10.2 to pick up new qemu and risc-v support.
Use Docker image 0.8.1 that includes an install of that SDK version.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
dtlib is meant to be general and anything-goes re. property values, but
edtlib can be pickier. Check that all 'status' properties have one of
the values listed in the devicetree specification
(https://www.devicetree.org/specifications/), and error out otherwise.
This will get rid of the 'status = "ok"'s (should be "okay") that keep
cropping up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Same deal as in commit a84ded74ea ("dts: Replace status = "ok" with
status = "okay""), for newly introduced stuff.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Route these to the equivalent pins for RXD1 and TXD1 on the Arduino
Mega.
Note that uart0 is routed to the debug probe IC on the nRF9160
DK, and uart1 is routed to where the RXD0 and TXD0 Arduino pins are on
the DK. This makes RXD1/TXD1 a logical place to put these UART pins,
since the header layout for the DK board matches the Arduino mega.
This is also necessary to keep some downstream code compiling which
needs to enable the UART2 but doesn't have a good place to put these
pins, since the new DTS parser is enforcing that all required
properties (like tx-pin and rx-pin in this case) are set for nodes
with status = "okay".
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
This adds a basic app which puts some rectangles on the display
It's hard to write an equivalent README to the rest of the sample
documentation, as the LCD I have uses a custom board thrown together for
testing. (ie other LCDs have publicly available modules)
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
This adds a driver for st7789v lcd controller, and TL019FQV01 lcd.
The bulk of the driver is based on the existing ili9340 driver.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
NRF_UICR needs to be defined for nRF9160 SoC in
nrfx_config_nrf9160.h, because it is not defined
in nrfx/hal/mdk/nrf9160.h (as it is a Secure-only
peripheral).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Authentication using OOB data uses the on-air device addresses used
during connection setup. So we need to check against the on-air
addresses in the info object to see if we have correct OOB data.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix issue with registering authentication callback handlers failing
without notifying the user of the shell.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use the src and dst naming to refer to the identity addresses of the
connection. Keep the device addresses used during connections but rename
them to local and remote instead.
Update documentation to be more descriptive.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Added tests of flash driver compatibility with fcb-backend.
For flash drivers which support write-block-size bigger than 1 B
test of unaligned data access uses native write-block-size
as it is dedicated to check whether settings works well on platform
which has 1 B access which is native on the current DUT.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
This is no longer needed after using
zephyr_interface_library_named cmake directive in the POSIX subsys
source itself.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Similar to how other sub-libraries are defined in Zephyr tree, e.g.
"fs", "lgvl", etc. This is supposed to help with the need to
explicitly add posix include path to each and every application using
POSIX subsys.
Fixes: #15627
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This is consistent with how newlib headers are treated, and will
have effect of ninlibc headers to be further down in the include
order. This is important, because some POSIX subsys headers
override those of libc. Without this change, we can't streamline
POSIX build config using zephyr_interface_library_named() cmake
directive, because includes will be in wrong order.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
To let any other zephyr_system_include_directories() directives
act first and get these paths in an order allowing Zephyr's stuff
override compiler headers.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Historically, it used to be "PTHREAD", which is no longer true, as
POSIX subsys offers much more functionality than just Pthreads. Use
detailed name, like "posix_subsys", to avoid possible confusion with
ARCH_POSIX-related matters.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
- Commands were not gathered with the right macro
- bus fault access due to wrong declaration of iface_states external
variable.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This commit adds a sample configuration for 6LoCAN to the
echo_client and echo_server example.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
The network to host byte order conversion is actually in place
on the network buffer. This prevents the reuse and forwarding of
RA packets. This commit uses temporary variables instead.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit adds support for a 6LoCAN Ethernet border translator.
CAN frames with the translator CAN address are translated and forwarded
to Ethernet. Ethernet frames with the first 34 bits matching the MAC
address of the translator are translated and forwarded to 6LoCAN.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Take the targer link layer address option link laxer addres lenght
from net packets source addres instead if the interface.
This is usefull for 6LoCAN border translator (6LoCAN to Ethernet).
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit implements net_pkt_shallow_clone. A shallow clone clones
the net_pkt but not the buffers. The buffers are only referenced and
therefor only freed when both copies of the net_pkt are freed.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commits adds support for reception of packets thats comes from
a Ethernet to 6LoCAN translator. This packets carry the Ethernet
MAC address (6 bytes) inline in the FF (First Frame).
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit is an implementation of 6LoCAN, a 6Lo adaption layer for
Controller Area Networks. 6LoCAN is not yet standardised.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Rename the socket_can implementation from CANBUS to CANBUS_RAW.
This is a preperation for 6LoCAN which is a CANBUS L2 for IPv6.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
subsys/bluetooth/host/Kconfig.gatt is already sourced within an
'if BT_CONN' in subsys/bluetooth/host/Kconfig.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
- update doc for different core configuration.
- fix some bugs in dts related files.
- add dts config and defconfig for different core configuration.
- end files with a newline in boards/arc/emsdp/board.dtsi
- remove unused head in boards/arc/emsdp/doc/index.rst
- ARC_MPU_VER in different core is fixed. so remove some useless code
for ARC_MPU_VER judgements in Kconfig.defconfig.* files for emsdp
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
Enable Mailbox support on 96Boards Avenger96 board. This will help
communicating to CortexA7 core.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Add onboard LEDs on 96Boards Avenger96 board. There are 4 user LEDs
on this board but only 3 are enabled. This is due to the fact that
LED0 is connected to unavailable PortZ. Hence, LED0 is ignored and
remaining LEDs are enabled starting from index 0.
Once PortZ is added, this will be fixed.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Fix the mandatory and optional parameter counts for the
directed adv shell command definition. Also, refactor the
command for consistency.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
It is possible that cmake in civetweb influenced the rest of the build
process, as described in #17996.
Right now only cmake version amd "project" directive is executed when
building from Zephyr but not requesting CONFIG_CIVETWEB.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Added test for check behavior on deleting existent entry,
nonexistent entry and already deleted entry.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
No need to write deletion entry for non-existing entry.
Furthermore such a write to filled up storage will make another
writes impossible as it occupied delete nvs_ate space, but it
does not remove anything.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
During initialization NVS analyzes open sector for
find write addresses. It was possible to infinite loop
in case when there was no space for any new ATE in the sector.
This patch introduce check for space available in the sector which
fix the issue.
fixes#17891
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
NVS always leave space for deletion ate in a full sector.
Even that it was not possible to write delete nvs_ate to the
full sector. Because of that it was possible to fill up NVS,
and be able to delete nothing.
This patch introduce recognition of case
the delete ate is writing, and allow to write such nvs_ate to
opened full sector.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Added test for check wheter initialization works well when nvs
storage is full filled. Test also check weheter can delet any
entry from full filled NVS.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
