Make drivers/net/ be the place for misc networking-related drivers
(otherwise, we'd need to have a new dir per driver).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
net_pkt_tcp_data() and net_pkt_udp_data() simply returns the start
address of the header. However the header may span over multiple
fragments, unexpected data or memory corruption might happen when
reading or writing to the pointer directly.
Use net_tcp_get_hdr() and net_udp_get_hdr() instead.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
The net_tcp_get/set_hdr() and net_udp_get/set_hdr() documentation
was not clear in corresponding header file. Clarify how the return
value of the function is supposed to be used.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
udp.h is out-of-date as it accesses net buf directly. In 3604c391, it
has been replaced by net/udp.h and udp_internal.h
Signed-off-by: Aska Wu <aska.wu@linaro.org>
Previously net_pkt.h, defined macros NET_PKT_TX_SLAB_DEFINE,
NET_PKT_DATA_POOL_DEFINE, but advertised them as intended for
"user specified data". However, net_pkt.c effectively used the
same parameters for slabs/pools, but this wasn't obvious due
to extra config param redirection. So, make following changes:
1. Rename NET_PKT_TX_SLAB_DEFINE() to NET_PKT_SLAB_DEFINE()
as nothing in its definition is TX-specific.
2. Remove extra indirection for config params, and use
NET_PKT_SLAB_DEFINE and NET_PKT_DATA_POOL_DEFINE to define
system pools.
3. Update docstrings for NET_PKT_SLAB_DEFINE and
NET_PKT_DATA_POOL_DEFINE.
Overall, this change removes vail of magic in the definition of
system pkt slabs/pools, making obvious the fact that any packet
slabs/pools - whether default system or additional, custom - are
defined in exactly the same manner (and thus work in the same manner
too).
Fixes#4327
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The relay functionality was supposed to be always enabled rather than
always disabled on the micro:bit.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
nucleo_f030r8 fails in CI because applications need
more RAM.
Reduce kernel memory used by stacks and ISR vector table.
Fixes#3923
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Some SOCs (e.g. STM32F0) can map the flash to address 0 and
the flash base address at the same time. Prevent writing to
duplicate flash address which stops the SOC.
Allow Cortex M SOCs to create their own vector table relocation
function.
Provide a relocation function for STM32F0x SOCs.
Fixes#3923
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The commit delivers HAL/LL static library source files for STM32F0 SoC.
Using STM32Cube provides generic access to all families, maximizes
code reuse across different STM32 families and helps taking benefits
of a mature SDK.
Origin: STM32Cube
URL: http://www.st.com/en/embedded-software/stm32cubef0.html
Purpose: Introduction of STM32F0xx STM32Cube definitions
and Abstraction Layers
Maintained-by: External
Original STM32Cube tree structure has been modified to a minimum
structure for a better fit into Zephyr. HAL is split into 2 parts:
-driver: initially Drivers/STM32F0xx_HAL_Driver, contains HAL and LL
-soc: initially Drivers/CMSIS/Device/ST/STM32F0xx, contains stm32f0xx
SoCs header files.
Fixes#3923
Signed-off-by: Maciej Debski <maciej.debski@rndity.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The original developer no longer has a working board and isn't
interested in maintaining support for the board. Mark the board
deprecated for now and see if anyone wants to pick it up, otherwise will
remove it in a future release.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Atmel SAM3X series has been recently converted to use ASF and
should now use common SAM family drivers. The i2c_atmel_sam3
I2C driver will be removed in the future.
This commit also changes the default I2C driver for Arduino Due
board from i2c_atmel_sam3 to i2c_sam_twi.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Match change we made to how I2C is enabled for other stm32 platforms:
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When hexdumping the packet, print also information if we
received / transmitted packet. Also print information if the
hexdump is before compression or not.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adding NET_MGMT_DEFINE_REQUEST_HANDLER to the doxygen configuration
list of pre-defined macros eliminates 800 lines of "expected" warning
messages from the document generation output. Generated API docs
are unchanged. Cool.
Remember this if/when other macros pop up as a problem for the
doxygen/breathe/sphinx API generation tools.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The file was opened as text, to avoid issues with UTF-8 in the future,
make it all binary and encode to UTF-8 correctly.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The predefined macro list for doxygen processing had a typo error
causing __attribute__(x) to not be handled correctly.
kernel.h was recently updated to include use of
__attribute__((sentinel)) and doxygen wasn't happy about
processing the API doc comments for the affected function.
Also added a couple of other predefined macros used in Zephyr.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Added arch specific calls to handle memory domain destroy
and removal of partition.
GH-3852
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
During swap the required page tables are configured. The outgoing
thread's memory domain pages are reset and the incoming thread's
memory domain is loaded. The pages are configured if userspace
is enabled and if memory domain has been initialized before
calling swap.
GH-3852
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Added architecture specific support for memory domain destroy
and remove partition for arm and nxp. An optimized version of
remove partition was also added.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Additional arch specific interfaces to handle memory domain
destroy and single partition removal.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
STM32 UART driver was using a mix of LL/HAL APIs. This commit removes
calls to HAL API and replaces them with LL APIs. No functional change
have been seen during non regression testing.
But we could note a direct gain of 1Kb of ROM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32F0/3 I2C's independent clock source supports only
HSI and SYSCLK, not APB1. We force I2C clock source to SYSCLK.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Refactors the mcux lpsci shim driver to use the clock control interface
instead of calling CLOCK_GetFreq() directly. This will allow SoCs with
different clock architectures to reuse this driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpuart shim driver to use the clock control interface
instead of calling CLOCK_GetFreq() directly. This will allow SoCs with
different clock architectures to reuse this driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use the clock control interface instead of calling CLOCK_GetFreq()
directly. This will allow SoCs with different clock architectures to
reuse this driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
