The Bluetooth Specification allows for optional Controller to Host flow
control based on the same credit-based mechanism as the Host to
Controller one. This is particularly useful in 2-chip solutions where
the Host and the Controller are connected via a physical link (UART, SPI
or similar) where the Host is sometimes required to ask the Controller
to throttle its data traffic while still making sure that relevant
events get through the line.
This implementation is based on a simple queue of pending events and
data that is populated whenever the Controller detects that the Host is
out of buffers and then emptied whenever the Host notifies the
Controller that is ready to receive data again. Events relevant to the
connections are also queued to preserve the order of arrival.
At this point the Controller ignores the connection handle sent by the
Host and treats all connections equally, and it also queues events even
for connections that have no data pending in the queue. Both this items
can be improved if necessity arises.
Note that Number of Completed Packets will still flow freely from the
Controller to the Host regardless of the pending ACL data packets, which
might lead to inconsistencies in the sequential order of certain
operations that include bi-directional data transfer.
Jira: ZEP-1735
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The files for the Arduino Due needed to be updated to use the new
configuration when the SoC moved from the atmel_sam3 directory to
the atmel_sam/sam3x directory.
Jira: ZEP-2067
Signed-off-by: Justin Watson <jwatson5@gmail.com>
This test generates a fault as part of the test,hence make the
test-suite aware of that by tagging it.
Signed-off-by: Rishi Khare <rishi.khare@intel.com>
There're (at least) 2 UART TX interrupt causes: "tx fifo has more
room" and "transmission of tx fifo complete". Zephyr API has only
one function to enable TX interrupts, uart_irq_tx_enable(), so it's
fair to assume it enables interrupt for both conditions. But then
immediately after enabling TX IRQ, it will be fired with "tx fifo
has more room" cause. If ISR doesn't do anything to fill FIFO, on
some architectures, immediately after return from ISR, it will be
fired again (with no instruction progress in the main application
thread). That's exactly the situation with this test, and on ARM,
it leads to inifnite IRQ loop.
So, instead move call to uart_fifo_fill() inside ISR, and be sure
to disable TX IRQ after we transmitted enough characters.
Change-Id: Ibbd05acf96b01fdb128f08054819fd104d6dfae8
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If the channel is already in use don't attempt to connect it a second
time.
Change-Id: I87bdaeadbe866b59c1a7975002699d9ef7a90c61
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CC3220SF_LAUNCHXL effectively replaces the CC3200_LAUNCHXL,
with support for the CC3220SF SoC, which is an update for
the CC3200 SoC.
This is supported by the Texas Instruments CC3220 SDK.
Jira: ZEP-1958
Change-Id: I2484d3ee87b7f909c783597d95128f2b45db36f2
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
For stream-based protocols (TCP), adding less data than requested
("short write") is generally not a problem - the rest of data can
be sent in the next packet. So, make net_pkt_append() return length
of written data instead of just bool flag, which makes it closer
to the behavior of POSIX send()/write() calls.
There're many users of older net_pkt_append() in the codebase
however, so net_pkt_append_all() convenience function is added which
keeps returning a boolean flag. All current users were converted to
this function, except for two:
samples/net/http_server/src/ssl_utils.c
samples/net/mbedtls_sslclient/src/tcp.c
Both are related to TLS and implement mbedTLS "tx callback", which
follows POSIX short-write semantics. Both cases also had a code to
workaround previous boolean-only behavior of net_pkt_append() - after
calling it, they measured length of the actual data added (but only
in case of successful return of net_pkt_append(), so that didn't
really help). So, these 2 cases are already improved.
Jira: ZEP-1984
Change-Id: Ibaf7c029b15e91b516d73dab3612eed190ee982b
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
In tickless kernel mode, time parameter of _sys_soc_suspend is in
milliseconds. Based on the kernel mode use the correct
mulitplier to convert to seconds.
Jira:1821
Change-Id: Idf156f56ece79a82729ebb124d1552a5eeb69e25
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Adds changes to enable existing kernel and timer tests and samples to
be used to test the tickless kernel feature.
Updated samples/philosophers and tests/kernel/timer/timer_api apps
Run the tests using following commands
make pristine && make BOARD=<board> CONF_FILE=prj_tickless.conf qemu
Board could be any of the following
qemu_x86
quark_se_c1000_devboard
Jira: ZEP-339 ZEP-1812
Change-Id: I1530b19b79ddeb0e2181594caf15f3ac28ff51f4
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Historically, space for struct k_thread was always carved out of the
thread's stack region. However, we want more control on where this data
will reside; in memory protection scenarios the stack may only be used
for actual stack data and nothing else.
On some platforms (particularly ARM), including kernel_arch_data.h from
the toplevel kernel.h exposes intractable circular dependency issues.
We create a new per-arch header "kernel_arch_thread.h" with very limited
scope; it only defines the three data structures necessary to instantiate
the arch-specific bits of a struct k_thread.
Change-Id: I3a55b4ed4270512e58cf671f327bb033ad7f4a4f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We want to show that if a non-essential thread gets a fatal exception,
that thread gets aborted but the rest of the system works properly.
We also test that k_oops() does the same.
Issue: ZEP-2052
Change-Id: I0f88bcae865bf12bb91bb55e50e8ac9721672434
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We reserve a specific vector in the IDT to trigger when we want to
enter a fatal exception state from software.
Disabled for drivers/build_all tests as we were up to the ROM limit
on Quark D2000.
Issue: ZEP-843
Change-Id: I4de7f025fba0691d07bcc3b3f0925973834496a0
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I6c676bc6c5e850a8725785554cd535e32067f33e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I4ec03eb2183d59ef86ea2c20d956e5d272656837
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Only 2 attributes lacked this prefix, which makes sense to have, so
applying it accordingly and changing the helpers as well.
Change-Id: I095b2729f977f8fb1624eff8801a4a4e21416693
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Most of these macros are not exactly exposing a buffer, but a specific
header pointer (ipv6, ivp4, ethernet and so on), so it relevant to
rename them accordingly.
Change-Id: I66e32f7c3f2bc75994befb28d823e24299a53f5c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- net_pkt becomes a stand-alone structure with network packet meta
information.
- network packet data is still managed through net_buf, mostly named
'frag'.
- net_pkt memory management is done through k_mem_slab
- function got introduced or relevantly renamed to target eithe net_pkt
or net_buf fragments.
- net_buf's sent_list ends up in net_pkt now, and thus helps to save
memory when TCP is enabled.
Change-Id: Ibd5c17df4f75891dec79db723a4c9fc704eb843d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Because of the way we build we can't expect relative paths back into the
Zephyr code base to work properlly. This just happens to work on some
systems because of the various -I that exist and one hits the right
number of subdirs between it and where the "at.h" lives. Lets instead
add the Zephyr root as a include path and explicit do a relative path
from the root to get the header.
We end up with a build failure with newlib enabled on galileo because it
ends up not having an include path that gets us to the proper spot with
the various ../../.. ...
Change-Id: I48b4dc2dffb76314f380efbcbbe25957ff5e9e07
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Tickless test dependency on legacy API is resolved, Changing
test directory from tests/legacy/kernel/test_tickless to
tests/kernel/test_tickless/.
Jira: ZEP-2008
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Change-Id: I0b53ae6eff3a915d988d3234592eb5f8b425b371
As part of Zephyr release 1.9 some APIs will be depreciated. This patch
replaces two of such APIs (task_sleep(ticks), sys_tick_get_32()) with
new ones (k_sleep(ms), k_uptime_get_32()).
Jira: ZEP-2008
Change-Id: Ic0e05906dadfb2ddaea9d0a8b738294dc81430f9
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
As test_sleep does not have dependency over legacy APIs.
So moving files from tests/legacy/kernel to tests/kernel.
Jira: ZEP-2009
Change-Id: I2439391ba6d0a194d07a0d1b48911d37b2f493b0
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
As part of Zephyr Release 1.9 some APIs will be depreciated.
This patch replaces APIs related to semophore init, kernel sleep,
task spawn etc.
Jira: ZEP-2009
Change-Id: I1fe09e9592f503c3413d51857fd740703173c042
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Added test cases to verify tickless idle concepts defined in
https://www.zephyrproject.org/doc/subsystems/power_management.html#tickless-idle
Test points:
verify system clock recovery after exiting tickless idle;
verify slicing scheduler behaves as expected
Jira: ZEP-339
Change-Id: Ic0a86d725e9692aa217375cedc7396372a026a88
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
newlib doesn't implement the internal buffer the same way that minimal
libc does, so only run that check with min libc (ie !CONFIG_NEWLIB_LIBC).
Also, reported the length we did get if the buffer is to big. Finally
include <stdarg.h> since we are dealing with va_lists and such.
Change-Id: I6b23e448e5785df978ac8c2757099e2b8aaace54
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We need a bit over 32k of memory to build/run the app_kernel benchmarks.
Change-Id: Iddfeb073f8ea87dc6323775a288b83efa88fdaea
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We renamed ztest's assert to zassert and the crc test case wasn't
updated to match so it doesn't build.
Change-Id: I67cd5bb6eef0875f31b8825d5c3aa5e1fa46af04
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ztest has a number of assert style macros and used a baseline assert()
that varies from the system definition of assert() so lets rename
everything as zassert to be clear.
Change-Id: I7f176b3bae94d1045054d665be8b5bda947e5bb0
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The directive exists for platforms that require more stack space than
usual. However, it wasn't being applied to the ztest thread stack
which ztest-enabled cases are run on.
Fixes numerous failures on xtensa simulator targets.
Change-Id: Iafa84de002421f03729c0f0cdeefdea51842ae32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
A recent patch added some new tests here. Unfortunately,
the current stack size value of 512 was too small for Xtensa.
Increase it to 1024.
Change-Id: I16c52b74412cbd7665e774ce3baed260885ddb9b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
A recent patch pinned the stack size for this test at 1024
instead of the platform default. This value wasn't sufficient
on Xtensa. Set to 2048, which was the default on most platforms.
Change-Id: I9a9d5fd448d2377aaf782c2c093a16147f31886a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This creates a test case that enables all the currently known
network related Kconfig options. This is useful so that we can
compile test various Kconfig options. Note that the result binary
is not meant to be run anywhere and it will probably not run as
some of the enabled options do not make sense in real life.
Change-Id: Iede36131b43d95acb78b4094004626e1b86e0f95
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Since commit-id 1ab40390c9 arp_input()
unrefs the buffer on success (NET_OK) so no need to do it afterward.
Change-Id: I84ab7e8eb07f50d52b329e4c025d88753a5de4db
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The Kconfig.rpl file was missing option to actually collect
RPL statistics. Unified the config option name to be
CONFIG_NET_STATISTICS_RPL as there was two conflicting settings
in the code and both of them were missing from Kconfig file.
Change-Id: I4ce4fcbaa317b36cac315ea3b3f710fa7a344b25
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add two testcases for mqtt_publisher and mqtt_subscriber.
The combination of the two, covering most of the MQTT APIs.
Change-Id: Ib663ee1f550362ca493501046ddf8508a25ac956
Signed-off-by: Wu Jiequan <jiequanx.wu@intel.com>
Ensure that the CRC16 functions compute a few test values properly.
Change-Id: Ie98049aefac8a330b9b81d3bf333deb09bc35c39
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Add net_nbuf_split() function that can be used to split
an existing net_buf fragment into two arbitrary length pieces,
and return the two new fragments to the caller. The data from
the original fragment is copied into these two new fragments.
Existing fragment is not modified.
Change-Id: I463e675232c6e19c2a42929f480893a6d1265873
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Incorrectly use variable even if it is null.
Coverity-CID: 157593
Change-Id: I883421a16870e5fe3c1d81e461f55f912ea168c0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
TC_START was missing from some tests. For this reason automated testing
parsing wasn't unified for all tests. This patch fixes the issue and adds
TC_START to tests where it was missing.
Change-Id: I7e27a3fd8eaef9c3d0b0e0aeba9bca5b97eb0c58
Signed-off-by: Milosz Wasilewski <milosz.wasilewski@linaro.org>
This test takes a bit longe than specified and fails on a daily basis
due to the low timeout specified.
Change-Id: Id774c35cb1b0d0dcc5455e4121a8e9e1612baafd
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Tinycrypt 0.2.6 fixed the issue with the definition of 'bool'.
Issue: ZEP-1722
Change-Id: Ie470e25dfe02a58d9c3f2324cab85bc02f574b51
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
it covers the story "Port AES-CMAC-PRF-128 [RFC 4615]
encryption library for Thread support"
ZEP-734
Change-Id: I6213309b51da435060c3e3cfadde67e21a927b2b
Signed-off-by: ethan gao <ethan.gao@intel.com>
Deleted the instance of app_kernel in tests/legacy/benchmark.
JIRA: ZEP-1980
Change-Id: I5a6e073d9b0c870be0cc7d8ae5bb352b11d7f97e
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
The BR/EDR configuration doesn't fit e.g. the Arduino 101 anymore.
Limit it to Qemu for the time being, which is anyway the primary
target where the functionality is being tested.
Change-Id: I9a34c82157d56079e43acabe29eeadd6d99e03fe
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
tests/kernel/context:
added test point to cover k_cpu_atomic_idle.
Jira: ZEP-1242
Change-Id: Id09c89fd367d527ea1087e6eb2bdba29a338ceaf
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
Coverity points out that uart_irq_update() return value
should be checked.
Coverity-CID: 166776
Change-Id: I3a754dae9e8f1563f4879e2fadfd89621785de8f
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
tests/kernel/common:
added test case to cover kernel clocks service.
https://www.zephyrproject.org/doc/kernel/timing/clocks.html
Jira: ZEP-1242
Change-Id: I40a06dd9d4dcb1ed24d488088eb2e456740c3bad
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
Add a configuration that strips the BLE controller down to its simplest
form to catch any issues when commonly used options are not enabled.
Change-Id: Ifbec01d62b7d45fe9139dadaba734eff3b7a72b6
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the controller's ability to drop duplicate advertising reports
when instructed by the Host.
Jira: ZEP-1246
Change-Id: I2d1b7abf1ed950dde705e5df30a858c595f3834c
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add Controller advanced Kconfig options to select IRQ
priorities of the Radio, Ticker's Worker and JOB IRQs.
This will provide an opportunity to have peripheral IRQ's
of higher level than Bluetooth Controller.
Change-id: Iaa128c1cd64a309a77d42d485fdefe68f31e4895
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig option to enable advanced scheduling in the
controller.
Enable non-overlapping placement of observer, initiator and
master roles in timespace. Uses window offset in connection
updates and uses connection parameter request in slave role
to negotiate non-overlapping placement with active master
roles to avoid slave roles drifting into active master
roles in the local controller.
This feature maximizes the average data transmission amongst
active concurrent master and slave connections while other
observer, initiator, master or slave roles are active in the
local controller.
Disabling this feature will lead to overlapping role in
timespace leading to skipped events amongst active roles.
Change-id: I16e4e6c3ca99f93987ab86924af0cb9d76bdbc7e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Added Kconfig option to enable advanced event preparation
feature.
Enables advanced event preparation offset ahead of radio
tx/rx, taking into account predictive processing time
requirements in preparation to the event, like control
procedure handling and CPU execution speeds. Crystal
oscillator is retained between closely spaced consecutive
radio events to reduce the overall number of crystal
settling current consumptions.
This feature maximizes radio utilization in an average role
event timeslice when they are closely spaced by using a
reduced offset between preparation and radio event.
By disabling this feature, the controller will use a
constant offset between the preparation and radio event. The
controller will toggle crystal oscillator between two
closely spaced radio events leading to higher average
current due to increased number of crystal settling current
consumptions.
Change-id: I19e640f7395ac7938873ef4bfac38acf8d6f7e0e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
If user is trying to use ztest by including ztest.h but has
not defined CONFIG_ZTEST, then fail the compilation as the
result binary will not do anything.
There is no check for CONFIG_ZTEST for unit tests that are run
without qemu.
Change-Id: Ief9bba3a3a0f6acc6a264f17cde828b6d7e543a5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The test failed to initilise these to known states, so fix this by
asking for end of transfer and error callbacks.
Change-Id: I523168381329062ec0c17aa41cb4033b78d8ed99
Signed-off-by: Jon Medhurst <tixy@linaro.org>
These were flagged by icx build.
Jira: ZEP-1887
Change-Id: Iaeedb13be23e86ebfb29a6441574b7384ae836e1
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
It needs to check if current event matches:
- cb's layer
- cb's layer code
- cb's command
If none match, it will not raise the event.
Fixing the unit test as layer must be always != 0.
Jira: ZEP-1940
Change-Id: Iadd63e751fa6e534a10e7da9cae0f5bb5a384461
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Most (if not all) 802.15.4 devices can handle ACK replies by
themselves.
Change-Id: I0319d59de767b20eb67c1592bacaa4a7b7015cad
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
commit id 7a11439020 changed this.
Hopefully that changed did not affect anything.
Reducing minimal frame length and applying the change everywhere where
relevant.
Change-Id: I5ae203751bfcf70cef833620106d2c2d0e33b7a5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It will first run the datasheet example.
Change-Id: Ic4da5ba9170a253cfdff4b17010d72dc86376555
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The neighbor was added very fragile way into neighbor cache which
caused following queries to fail. This is now fixed by manually
adding neighbor to the cache.
Change-Id: I1831557fd5f9df5afd0a6c6833b0af769f5167eb
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Couple of tests started to fail without any apparent reason.
Disabling them temporarily until the root cause is found.
Change-Id: Id82e0eab60dc744c8ce6f02a5834e731be153883
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The ECC DSA test case was updated in TinyCrypt 0.2.6.
Fix the length of the random vector.
Change-Id: I7545a51c6855959afdefe00a1e0b53e5c3001a7c
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The ECC DH test case was updated in TinyCrypt 0.2.6.
This patch adds two helper arrays for the Monte Carlo routine.
Change-Id: If28292512b351feffc3fe470942cd97b18851a57
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This adds a test suite for the JSON library, testing both encoding and
decoding of all supported data types, including arrays, nested objects,
and basic types such as booleans, numbers, and strings.
Jira: ZEP-1607
Change-Id: I4f6ad7e2859a142e06d405e0760e91751e01a31f
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This way we can monitor testcases for faults that should not be there;
however, in the case of these, a fault message is expected and shall
be ignored.
Change-Id: I63736723026c381c9fee7f24a751ceafc12f2a40
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Legacy APIs are to be deprecated, so getting rid of tests that have been
moved to unified kernel already.
Change-Id: I752e42bc498dfdd0ea29b0b5b7b9da1dac7b1136
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Refining the names around IPv6's neighbor states to differentiate them
easily from any net_nbr related names (which are not tighten to IPv6).
Change-Id: Ibc24df2a9485477a53fe5fe1c8f993f0fcd91635
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This fixes an issue introduced by bab3aafa2d,
which changed the default value of UART_PIPE_ON_DEV_NAME to the same
used by BLUETOOTH_UART_ON_DEV_NAME. Due to this, the BTP and HCI were using
the same UART.
Change-Id: Ib59819e49610f28f4c89c0304d024bb1b6aa506a
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
This is the port of the legacy/kernel/test_pend test case to
the unified kernel
Jira: ZEP-932
Change-Id: I81762b45ff7000ff9f6079c674b46d233b2645de
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Added conn-update command to btshell module to test
bt_conn_le_param_update Bluetooth API.
Change-id: I205df9ffc12a0ab062de5a779ab96bc91cbd9259
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Reordered the commands in btshell to represent the logical
order of use. Moved advertise and scan before connect
command.
Change-id: Id64509e39848109a6df7ddb1306b6bd221b65c40
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add proper logging for errors in the same go.
Change-Id: I8bd4fa8d5b143e51024496bfba0056525ad35964
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Declaring these as const lets the linker generate more optimal code.
Some extra care is needed with hci_ecc.c since it was overwriting the
send callback. Now the choice of send() call is done directly in the
bt_send() function
Change-Id: Iac74f5ee9bee097bbb34c11bd13d1d886700f5cc
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add a Controller event that indicates everytime
advertisement event has been transmitted on air.
Change-id: I4722488bbfeca987e66983faf5b26467407a89c9
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Due to commit 8308b9bd2d ("net/http: Add the HTTP/1.1 API")
every user of CONFIG_HTTP_PARSER would need to add CONFIG_HTTP to
their .conf files. Which is fine for intree samples/tests as they
have been adjusted, but the rest of world working on Zephyr apps
will need to make this changes as well.
Instead, we should have each of the following select HTTP instead of
depend on it, which will make future use of these configs and their
dependencies more intuitive:
HTTP_SERVER
HTTP_CLIENT
HTTP_PARSER
NOTE: As cleanup, this commit also removes the CONFIG_HTTP added to
samples and test .conf files.
Change-Id: I81cfaa19e37333b1bf98778f8147814780e7f77c
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Add CONFIG_NET_IPV6_NBR_CACHE option that is the base for both
neighbor discovery (ND) and duplicate address detection (DAD).
Both ND and DAD can be disabled if needed. If NBR cache is
disabled, then ND and DAD are disabled too.
Note that it makes not much sense to disable DAD or NBR cache
as IPv6 will not work properly without them. It is possible
to disable ND but then the neighbor information needs to come
via other sources like RPL.
Change-Id: I57c8668ad828b3a153dfc58eea78bf5f7ac3938a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use the proper MAC address space (00-00-5E-00-53-xx) dedicated
for documentation and specified in RFC 7042 ch 2.1.2.
Change-Id: If8ef9e4ee4e041ad005060664ebafe60df0a6bf9
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Test net_mgmt_event_wait() and net_mgmt_event_wait_on_iface()
Change-Id: I82ba70a697f0d13aa2e1eef2110e139b3621c119
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of creating a handler and a related callback structure on an
event_mask: net_mgmt_event_wait() can be used to wait synchronously on
such event_mask. The core mgmt part will seamlessly reuse the struct
net_mgmt_event_callback so the whole internal notification mechanism is
using the same code.
Change-Id: I426d782c770e75e5222aa3c5b703172b1f1f2e5e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Current finalize api's takes buf as input parameter and returns
the finalized buf. But if there are any issue while finalizing,
it failed to throw an error.
Change-Id: I6db54b7453eec41a8051fab50d5c0dc937debd54
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
As per RFC 6775 4.2, context length holds number of leading bits
in the Context Prefix field that are valid. Rest are not valid
for compression.
Change-Id: Id21cc2d7a5d42980cf9295f85e75c4869ff6cb99
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This patch adds some routines to evaluate DNS responses as specified
by RFC 1035.
Jira: ZEP-1876
Change-Id: Ia78a1175229962128a0bcee985e507d72ed26aea
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch adds the HTTP/1.1 API for Zephyr. This API consists of client
and server context structures enabled via Kconfig variables.
HTTP parser support is enabled via the CONFIG_HTTP_PARSER configuration
variable.
Currently, this API only includes support for writing HTTP requests
(client mode) and HTTP responses (server mode). TLS support is not
considered in this iteration.
Supported HTTP methods:
GET, HEAD, OPTIONS and POST.
Supported HTTP responses:
400, 403 404. The http_response routine may be used to write
any HTTP status code, for example 200 OK.
Jira: ZEP-1701
Change-Id: Ic9ccd4d4578d6d0f3a439976ea332b031644ca7d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch adds the test case for the DNS API low-level routines.
The following routines are evaluated by this test case:
- dns_msg_pack_qname
- dns_msg_pack_query
- dns_unpack_header_id
- dns_header_qr
- dns_header_opcode
- dns_header_aa
- dns_header_tc
- dns_header_rd
- dns_header_ra
- dns_header_z
- dns_header_rcode
- dns_header_qdcount
- dns_header_ancount
- dns_header_nscount
- dns_header_arcount
- dns_unpack_query_qclass
- dns_unpack_query_qtype
Next iterations will consider IPv6 and DNS RR coverage.
Jira: ZEP-1499
Change-Id: I4ef46203e6fec57c6fe5a5db8132ed140b412fc2
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Make sure that the network interface has proper allnodes and
solicit node multicast addresses set.
Change-Id: I2318d63df0b5d09dfaa8347b69c843b84ed63f4b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add tests for verifying that we can receive Multicast Listener
Discovery query and act on it.
Change-Id: I926cf5e9f77cd250d2d7094f2379e320ef163540
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive MLDv2 (Multicast Listener Discover) query,
we send out information about the multicast groups that
we have joined.
Change-Id: If4ea9fa685319b2ad900e1949a5cbe12e7696b43
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
MLD (Multicast Listerer Discovery) unit tests when joining
or leaving an IPv6 multicast group.
Change-Id: I7cd0f4c5f31c693d816fb5d27d3d23bb27679c35
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When we setup the network interface, add predefined IPv6 multicast
groups into the network interface. When interface is taken down,
then leave all the multicast groups that joined.
See RFC 4291 ch 2.8 for details.
Change-Id: If17d3e8c75157a02aa93c92e2fb499619c1484cf
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This and subsequent commits adds API to join or leave
an IPv6 multicast group.
Jira: ZEP-1673
Change-Id: I26dcfe16a4527dbf7886a30827a5d4ebfdeaac01
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Variable len is not used in net_icmpv6_input() and if required
it can be obtained from 'buf'.
Change-Id: I4b0710e1cf16cff9837173ad9d6908ec54ebafae
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Instead of always calling net_nbuf_get_reserve_tx() with zero
ll_reserve (first parameter) and then setting the link layer
reserve separately, pass the reserve to that function which can
then set the ll_reserve in buf itself.
Change-Id: I21c14cb7e2e6c36d170c09998bca0207ecf65c75
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The ll_reserve parameter is useless in net_ipv{4|6}_create_raw()
function as the reserve information is already stored in buf.
Change-Id: I7815a78c001e3da532478c04b3dac9b37bbc723c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code used net_nbuf_get_reserve_{rx|tx}_data() function to
allocate a fragment. Instead of that low level function, use
net_nbuf_get_frag() instead. There are few places this is not
possible or is too big change like in few test programs.
Change-Id: Ied7e2b7db352de998b200ffa6ff82471bfa5ebe3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive lot of packets, it might happen that we exhaust
all the DATA buffers in the system. This would prevent from
us sending anything to the network.
Change this by splitting the DATA buffer pool into RX and TX
parts. This way RX flooding cannot consume all DATA buffers
that needs to be sent.
Change-Id: I8e8934c6d5fdd47b579ffa6268721b5eb3d64b6d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It makes no sense to modify the original net_buf so change the
copy function not to touch the original buffer.
Change-Id: I5d22445ce50cee62994c36567f0e995a500cb89d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The first parameter of net_nbuf_copy() must be the head
of the buffer chain i.e., it must contain the user_data
part. If a fragment is given, then we do not know enough
information to allocate the data fragments.
Change-Id: I052b183d8c63d7326b320254f36f00b2fc48b0a0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add pin definitions to enable GPIO cases to run on
Quark D2000.
Add pin definitions to enable GPIO cases to run on
arduino_101_sss.
Change-Id: I97eadb8316b1f80b899b167a01effab815626dae
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
According to ZEP-1717, removing the callback from
the gpio is not enough to disable interruptions.
You also need to call gpio_pin_configure() on
the input pin without the GPIO_INT flag to totally
disable the interrupt for the pin.
This commit will stop level interrupt from being
fired constantly.
Change-Id: I019d7cea0bc0d5e5ff4b74165472ed11de1733bb
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
These were flagged by icx build.
Jira: ZEP-1864
Change-Id: I5b8fce64d9e20d768fabf02e2a799e9390e3679a
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Separate out data element structure header into type and size fields
Change-Id: I869ee1ea82db1f6d669bb905055135b7d63f3fa2
Signed-off-by: Kaustav Dey Biswas <kaustav.d.biswas@intel.com>
Parameters and data must be permament for time of the operation.
Change-Id: Idd4eee948e62c2c80648116a339558042059f801
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Instead of passing exact value allow to use 'ind' for enabling
indications instead of notifications.
Change-Id: I24306a321ed90b4bcb6300846218ff7214b39bc4
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Don't echo data from received callback as this can cause
deadlock. Just dump incoming data instead.
Change-Id: Iedbbafd0406ad46ba2c9d26fd8a70fff59de8143
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
argc needs to be check before accessing argv.
Change-Id: I9cb70906a388b96df4e192dd4f31eafdab25127f
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Add __printf_like attribute to printf style functions in minimal libc to
enable the compiler checking this provides. We fixup the associated
issues that are now found by utilizing these checks.
Change-Id: I74ac0d0345782463d9fb454f7161d6b4af211ba5
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
It was named 'mutex', which is not representative of what it is used for
since it is not used for mutual exclusion, but rather for signaling.
Change-Id: Icfef0011f890b2546af1686ba6b57e3fc13c6576
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
There is an implicit expectation that the priority of threads spawned by
a ztest suite is still higher than the main suite thread own priority
when a test signals the main suite thread that it has completed.
Change-Id: Id7caec3e9e553712c828a93c212b8e82bd16eabd
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
That was an oversight that should not have caused any problem. However,
the test harness expects the test's thread to be higher prio than the
test suite's thread that spawns it, because the test suite reuses the
stack space for the next test, if there is one.
Change-Id: Iad951118278abf0d9c23012d78ed56b75bc2958a
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
Current users of sys_bitfield*() are bending over backwards to cast
what is most of the times a pointer into an integer.
Bitfields can be better described with an void *, so
uint{8,16,32,64}_t or any other container can be used. Most
sys_bitfield*() operations, by extension, can do the same. Note void *
has byte arithmetic, like char *.
This change will also make it implicit, for any future split of the
address space between virtual (what the SW is seeing) and physical
(what the HW is seeing) way clearer, as the functions dealing with
physical, non directly referentiable/mappeable addreses to use an
integer type, like mem_addr_t.
- include/arch/ARCH/*asm_inline*:
- sys_bitfield*() all modified to take 'void *'
Note 'void *' arihtmethic is byte based, which makes some things
easier.
- include/sys_io.h:
- introduces DEFINE_BITFIELD
- update docs
- tests/kernel/bitfield: remove all the cast contortions, use DEFINE_BITFIELD
PENDING: update other TCs
- include/arch/nios/nios2.h, drivers/interrupt_controller/ioapic_intr.c:
remove cast contortions
Change-Id: I901e62c76af46f26ff0d29cdc37099597f884511
Jira: ZEP-1347
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
tests/kernel/pipe/test_pipe_api:
added test cases to cover k_pipe_block_put.
Also added test case to verify [get, put] API sequence.
Jira: ZEP-1242
Change-Id: I755def474592ea2bf36d8644c8f4a07a7a80bad0
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
tests/kernel/workq/workq_api:
added test point to cover k_delayed_work_remaining_get
Jira: ZEP-1242
Change-Id: I15055e9b11dfd28f3e33ac04151df8ccbed97027
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
tests/kernel/fifo/test_fifo_api:
added test case to cover k_fifo_is_empty.
Jira: ZEP-1242
Change-Id: I9559df8661dbcd7d4885fa2db928120e945b3ae1
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
tests/kernel/threads_scheduling/schedule_api:
added test case to cover k_is_preempt_thread.
Jira: ZEP-1242
Change-Id: I4327438dffaa59abcfe1e41813b45abee88506b2
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
Once all users of k_lifo migrate to k_queue this should no longer be
needed.
Change-Id: Ib8af40c57bf8feba7b06d6d891cfa57b44faad42
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes k_fifo functions rely on k_queue and port k_poll to use
k_queue directly.
Once all users of k_fifo migrate to k_queue this should no longer be
needed.
Change-Id: Icf16d580f88d11b2cb89e1abd23ae314f43dbd20
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is possible that the buffer waiting for retransmission is modified
after it is sent, for example, it can be compacted by 6lo, and our
assumption of where is the message ID is located in the buffer is no
longer valid.
As the message ID is the only information that is necessary for
keeping track of retransmissions, we keep a copy of it in the pending
struct, as well as the destination address of the retransmission.
Change-Id: Id33d54353404628673541225a1a05e27ee08765f
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This unit test verifies that zoap_packet_get_payload() returns the
expected size for received packets.
Jira: ZEP-1662
Change-Id: Ibe011959f4d6593f4f20f0f5901c9033c76c9518
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This reverts commit 7b652b1f84.
Breaks on many boards.
Change-Id: Ie74e7a656094a54b999b99de9a462093525202c3
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Depending on test environment, termination character could
be '/r' instead of '/n'.
Enabling both possibilities.
Change-Id: I18b47e9055667e0a4f868416ee8d01226a879712
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order for interrupt reset mode to work (reset the processor
after and interrupt) the interrupt does not has to be cleared,
and the qmsi hal layer clears the interrupt after the callback
has been invoked, the callback does not return and the processor
should reset.
Jira: ZEP-1566
Change-Id: Ic951a0f15fe95fb0ef5d752b831c62e6fa3ceea0
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
The include guard has a misspelling.
Jira: ZEP-1746
Change-Id: I4d8000ef5c8e037f80acbf2491d0b9466670816a
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This patch excludes qemu riscv32 due to the following msg:
qemu-system-riscv32: cannot set up guest memory
'riscv_sifive_board.ram': Cannot allocate memory
Jira: ZEP-1721
Change-Id: Ib1784fa57ad1e3d69871d4e216af1ad5dbe55a76
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
After QMSI 1.4 update, the alarm callback is not saved when
'alarm_en' is set to zero during RTC configuration. So this
patch fixes tests/power/multicore/lmt application according.
ZEP-1778
Change-Id: Ie1468458bc23a6394484aef2aeee97745d5d23b8
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
The interface L2 address type is set at the same time as the
L2 address is set to the network interface. This is most
convinient place to set the address type.
Change-Id: I712d7357d075959eb79df3463141cfbc6d163a74
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
k_cycle_get_32() needs to return a monotonically increasing value,
except in cases of 32-bit integer overflow. Enforce this with a
test case.
We also check that the number of cycles elapsed after sleeping for 1
second is at the expected value. This can help catch errors on platforms
that use different timer sources for the system clock and timestamps.
This test case adapted from some code provided by Sergey Arkhipov
when troubleshooting ZEP-1546.
Issue: ZEP-1546
Change-Id: If27fff026ea6de659f7b41b60ff26f4962b734d4
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Some files made it through review process with full license header.
Change-Id: I2722b127c40b4b19500042c12e4fde85a165bae9
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some arches may want to define this as an inline function, or
define in core arch code instead of timer driver code.
Unfortunately, this means we need to remove from the footprint
tests, but this is not typically a large function.
Issue: ZEP-1546
Change-Id: Ic0d7a33507da855995838f4703d872cd613a2ca2
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
A _tsc_read has been added for ARC targets.
This test can use that when ARC.
See ZEP-1413
Change-Id: Ib63aecbe9f3eb2b97ad1086fc79b57e8f0774fca
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Timeouts, when expiring on the same tick, should be handled in the same
order they were queued.
Change-Id: I23a8e971a47ca056b32b8b48fe179d481bae27c0
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
Currently, for the following MQTT msg fields:
- client_id
- will_topic
- user_name
- topic
their length is computed inside the routine that receives the MQTT msg.
Although this simplifies development, also imposes one restriction:
data must be null-terminated. Sometimes, data is received from other
sources and not generated by the application, so the null-terminated
constraint may be considered problematic for the user.
This patch removes the assumption that string fields are null-terminated.
Current data structures are already prepared to handle this case, so no
API change is required.
Change-Id: I5a147a5b21e0da49541cbe62baac363c8737cd3e
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
So far, only implemented on ARM.
It's not possible to do this on Nios II and RISC-V.
Change-Id: I84c8d99cd163dff46de4bc4a7ae40768daf8e4ce
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
obj_tracing test from legacy modified to use unified APIs
directly.
Jira: ZEP-932
Change-Id: Ib5d300334e527b842668be076c94c40b65d7cbe4
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Remove tests that assert due to invocation from ISR which is not supported.
Change-Id: Ib2313b8f75db0140aa475281bd76ba0414d6a481
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
This was reported by ISSM compiler.
Jira: ZEP-1179
Change-Id: Ib97ed8da830126c9fbfa2269c8b2327d2f1be2f4
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
This was reported by ISSM compiler.
Jira: ZEP-1179
Change-Id: I5700ff6b374815325fa858cfd11f8938c82d8337
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Tinycrypt's definition of 'bool' does not work properly with
Xtensa's XCC compiler.
Issue: ZEP-1722
Change-Id: Id71b5f1bcf738c83e672b64a592a68751758dbc9
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This option is added in order to support Xtensa, which needs more stack than
other architecture. This allows having a centralized way to change stack
requirements for all tests.
This extra stack size is eaqual to 0 for most architectures, except Xtensa
which requires additional 768 bytes for each stack.
Change-Id: Ie5dcae1dfd29018d36ef35dae22dc4c1a2ecdc14
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
The test will also need to increase the stack to run correctly for Xtensa cores.
Change-Id: If94f12a941dc8eccf879558bdebdc7ccb2d047f1
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
When test GPIO_INT_EDGE, there is no code to skip GPIO_INT_LEVEL
and jump to the end of the function. So GPIO_INT_LEVEL will
always be checked (Besides, it't always true), even if it's
testing GPIO_INT_EDGE, which will cause GPIO_INT_EDGE cases fail.
Add a goto statement for GPIO_INT_EDGE to skip GPIO_INT_LEVEL.
Jira: ZEP-1685
Change-Id: I10ce21c04c49f34aafdc2cd2f60f3e5377d6f1f5
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
This test case uses PWM0 port to test PWM on Quark Se.
However PWM0 port on Quark D2000 is initialized as tdo,
not PWM0 and disabling tdo will kill JTAG on D2000. So
use PWM1 and add PINMUX setting code to configure PIN_24
as PWM1 port, then the case will work on D2000 board.
Change-Id: Ib28d4750dac7396529388b781fb64bde048139d6
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
the commit test below adc driver api with different resolutions
and modes
adc_enable()
adc_read()
adc_disable()
move original adc test to adc_simple folder
Change-Id: I016b5e67a5d89fc8d5ae76f33799e5d3eb3e1cf8
Signed-off-by: jing wang <jing.j.wang@intel.com>
Remove tests that assert due to invocation from ISR which is not supported.
Change-Id: Idd2360847a467af6afdd9fbed8f87a620d9ed2f7
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update the dma loop transfer sample app to use the new
dma api interfaces. This change is based on the api change
and the updated dma driver.
A RFC was posted recently on this.
Jira: ZEP-873
Change-Id: I289e2e08d4c775a833bf3d585d2706a903edd0bc
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This test is intended to verify that the SW ISR and vector tables
have been populated correctly.
Change-Id: Ic7f50c02dc0807d7ddefa710da67f818ff707ad6
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This replaces the hard-coded vector table, as well as the
software ISR table created by the linker. Now both are generated
in build via script.
Issue: ZEP-1038, ZEP-1165
Change-Id: Ie6faaf8f7ea3a7a25ecb542f6cf7740836ad7da3
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
These were reported by ISSM compiler.
Jira: ZEP-1179
Change-Id: Ic625749309773611c0c6ba2905e9420e98947dae
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Update the dma block transfer sample app to use the new
dma api interfaces. This change is based on the api change
and the updated dma driver.
A RFC was posted recently on this.
Jira: ZEP-873
Change-Id: Icf3bec7260c2e499485b07a4a579956448a1a3fd
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Using net_buf_unref() technically works but debugging the network buffer
allocations is more difficult if done like that.
Change-Id: Ieaa0978aa69e2f0baa924fe842ca1f116c348ef1
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
this commit check the priority of 2 system threads - main and idle
Change-Id: Ie57e7fdab3d15c0b69d85ed6282bfa6aa04133b4
Signed-off-by: jing wang <jing.j.wang@intel.com>
Current API description of net_nbuf_compact() is not very clear.
The first parameter needs to be the first net_buf in the chain.
The changes to this API are needed in order to clarify following
use cases:
1) User provides fragment that is not first of the chain and compact is
successfully done. In this case there is no free space in fragment list
after the input fragment. But there might be empty space in previous
fragments. So fragment chain is not completely compacted.
2) What if input fragment has been deleted and api returns the same
buf?
So this commit simplifies the API behavior. Now net_nbuf_compact()
expects the first parameter to be either TX or RX net_buf and then it
compacts it. It fails only if the input fragment is a data fragment.
Change-Id: I9e02dfcb6f3f2e2998826522a25ec207850a8056
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The net_nbuf_push() API is not used by anyone. Semantics are not
clear and following patch requires changes to push api, so removing
this API for now. If needed this can be re-introduced later.
Change-Id: I1d669c861590aa9bc80cc1ccb08144bd6020dac5
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Test with max data in order to test the fragmentation code better.
Change-Id: I301a96eae1dd637f0291354120389c2bd7575695
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This commit changes the net_buf getter functions in nbuf.h
by adding a timeout parameter. These function prototypes
are changed to accept a timeout parameter.
net_nbuf_get_rx()
net_nbuf_get_tx()
net_nbuf_get_data()
net_nbuf_get_reserve_rx()
net_nbuf_get_reserve_tx()
net_nbuf_get_reserve_data()
net_nbuf_copy()
net_nbuf_copy_all()
net_nbuf_push()
net_nbuf_append()
net_nbuf_write()
net_nbuf_insert()
Following convinience functions have not been changed
net_nbuf_append_u8
net_nbuf_append_be16
net_nbuf_append_be32
net_nbuf_insert_u8
net_nbuf_insert_be16
net_nbuf_insert_be32
net_nbuf_write_u8
net_nbuf_write_be16
net_nbuf_write_be32
so they call the base function using K_FOREVER. Use the
base function if you want to have a timeout when net_buf
is allocated.
Change-Id: I20bb602ffb73069e5a02668fce60575141586c0f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This was ported to the new kernel, no need to keep the old one around.
Change-Id: I02d39c8e39843cee1862448296e9c1d0dfde75b9
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Adds to BT shell app functionality to trigger to be found on remote
A2SRC UUID. Implements user callback to read resolved response data
and uses existing SDP client API to read attributes values.
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 77
Count: 1
> ACL Data RX: Handle 77 flags 0x02 dlen 48
Channel: 64 len 44 [PSM 1 mode 0] {chan 0}
SDP: Service Search Attribute Response (0x07) tid 2 len 39
Attribute bytes: 36
Continuation state: 0
Combined attribute bytes: 89
Attribute list: [len 84] {position 0}
Attribute: Service Record Handle (0x0000) [len 2]
0x00010005
Attribute: Service Class ID List (0x0001) [len 2]
UUID (3) with 2 bytes [0 extra bits] len 3
Audio Source (0x110a)
Attribute: Protocol Descriptor List (0x0004) [len 2]
Sequence (6) with 6 bytes [8 extra bits] len 8
UUID (3) with 2 bytes [0 extra bits] len 3
L2CAP (0x0100)
Unsigned Integer (1) with 2 bytes [0 extra bits] len 3
0x0019
Sequence (6) with 6 bytes [8 extra bits] len 8
UUID (3) with 2 bytes [0 extra bits] len 3
AVDTP (0x0019)
Unsigned Integer (1) with 2 bytes [0 extra bits] len 3
0x0102
Attribute: Browse Group List (0x0005) [len 2]
UUID (3) with 2 bytes [0 extra bits] len 3
Public Browse Root (0x1002)
Attribute: Bluetooth Profile Descriptor List (0x0009) [len 2]
Sequence (6) with 6 bytes [8 extra bits] len 8
UUID (3) with 2 bytes [0 extra bits] len 3
Advanced Audio Distribution (0x110d)
Unsigned Integer (1) with 2 bytes [0 extra bits] len 3
0x0102
Attribute: Unknown (0x0100) [len 2]
Advanced Audio [len 15]
Attribute: Unknown (0x0311) [len 2]
0x0001
< ACL Data TX: Handle 77 flags 0x00 dlen 12
L2CAP: Disconnection Request (0x06) ident 10 len 4
Destination CID: 65
Change-Id: I8938d9eebda31f3d252ff49adc1a96abfcbc5751
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Makes use ProfileDescriptorList atribute API to get remote Hands-Free
profile version.
Jira: ZEP-1112
Change-Id: I3752691057e15c3a9a681dd3277ac160096792e9
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Adds pool memory for storing SDP client query results and introduces
command allowing add HFPAG UUID to be resolved when connection to peer
is already set. When resolved data arrives, UUID callback handler
tries to identify RFCOMM protocol specific information, in this case
remote HFPAG Server Channel Number, stored in Protocol's Descriptor List
attribute data.
> HCI Event: Number of Completed Packets (0x13) plen
Num handles: 1
Handle: 77
Count: 1
> ACL Data RX: Handle 77 flags 0x02 dlen 55
Channel: 64 len 51 [PSM 1 mode 0] {chan 0}
SDP: Service Search Attribute Response (0x07) tid 2 len 46
Attribute bytes: 43
Continuation state: 0
Combined attribute bytes: 96
Attribute list: [len 91] {position 0}
Attribute: Service Record Handle (0x0000) [len 2]
0x00010003
Attribute: Service Class ID List (0x0001) [len 2]
UUID (3) with 2 bytes [0 extra bits] len 3
Handsfree Audio Gateway (0x111f)
UUID (3) with 2 bytes [0 extra bits] len 3
Generic Audio (0x1203)
Attribute: Protocol Descriptor List (0x0004) [len 2]
Sequence (6) with 3 bytes [8 extra bits] len 5
UUID (3) with 2 bytes [0 extra bits] len 3
L2CAP (0x0100)
Sequence (6) with 5 bytes [8 extra bits] len 7
UUID (3) with 2 bytes [0 extra bits] len 3
RFCOMM (0x0003)
Unsigned Integer (1) with 1 byte [0 extra bits] len 2
0x03
Attribute: Browse Group List (0x0005) [len 2]
UUID (3) with 2 bytes [0 extra bits] len 3
Public Browse Root (0x1002)
Attribute: Bluetooth Profile Descriptor List (0x0009) [len 2]
Sequence (6) with 6 bytes [8 extra bits] len 8
UUID (3) with 2 bytes [0 extra bits] len 3
Handsfree (0x111e)
Unsigned Integer (1) with 2 bytes [0 extra bits] len 3
0x0106
Attribute: Unknown (0x0100) [len 2]
Handsfree Gateway [len 18]
Attribute: Unknown (0x0301) [len 2]
0x01
Attribute: Unknown (0x0311) [len 2]
0x0027
< ACL Data TX: Handle 77 flags 0x00 dlen 12
L2CAP: Disconnection Request (0x06) ident 5 len 4
Destination CID: 64
Source CID: 64
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 77
Count: 1
> ACL Data RX: Handle 77 flags 0x02 dlen 12
L2CAP: Disconnection Response (0x07) ident 5 len 4
Destination CID: 64
Source CID: 64
Jira: ZEP-1112
Change-Id: Ibda606fabe367ca3d0353f77c7093da8c4f175c8
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
riscv defines the machine-mode timer registers that are implemented
by the all riscv SOCs that follow the riscv privileged architecture
specification.
The timer registers implemented in riscv-qemu follow this specification.
To account for future riscv SOCs, reimplement the riscv_qemu_driver by
the riscv_machine_driver.
Change-Id: I645b03c91b4e07d0f2609908decc27ba9b8240d4
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
If we send unicast NS, then the destination IPv6 address needs
to be in the neighbor cache, otherwise we have a NS sending loop.
Change-Id: I11e8f5d5740248024a0becc77055786cd2e32199
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The compact function was never really properly tested
but it is used by other routines that have unit tests.
This commit makes sure there is a special testing for
the buffer compact function.
Change-Id: I35c108fd8459a9482ccae68a51ffa28fb2e0ae99
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This tests access to standard libraries. Adapted
to use ZTEST.
Jira: ZEP-932
Change-Id: I3564bfa61221b2456323c1018402237b6129b5ca
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some header files were defining MON and causing a conflict, so call this
something unique and avoid future conflicts.
Change-Id: If9d2553a20b3afae50a09f4c0e10733ee1cdd58d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is the microkernel version of the FPU sharing test from legacy
modified to use unified APIs directly.
Jira: ZEP-932
Change-Id: I133a1466ea75201a97c2f8b83c3586fea0a19447
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Each GCC target backend is at liberty to define its own SIZE_TYPE. GCC
uses this for various purposes, not lease it drives the machinery that
spits out format specifier diagnostics when format specifiers are
applied to objects with inappropriate type. GCC exposes the current
definition of SIZE_TYPE via the preprocessor symbol __SIZE_TYPE__.
The GCC build processes also generates various standard library header
files that directyle expose stanard types in a form consistent with
the current configuration of GCC. Conventionally standard library
build processes (for glibc and newlib) pick up the header files
generated by the GCC build.
In the minimal libc we have no such build process, we don't pick up
the header files that the GCC build process generated. Instead we
define our own alternative header files and align them with GCC
manually.
The current definition of ssize_t in minimal libc is out of step with
GCC which means that any use of the %z[du] format modifier will issue
a diagnostic.
We replace the open coded architecture detection in minimal libc and
use GCCs __SIZE_TYPE__ directly.
Change-Id: I63b5e17bee4f4ab83d49e492e58efd3bafe76807
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
tests: fs: Fix printf warning when using newlib
Current code uses %ld format specifier to print data of
type ssize_t. This causes type warnings when built with
newlib. The correct format specifier to be used for
ssize_t is %zd.
Change-Id: I02a3c628e3d6e8a36a09cd694220406d8faf1730
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
We ended up having "benchmark" and "benchmarks". This
fixes that.
Change-Id: I7ebc409e002e11f5bc9dc821310dd84f3982b8d4
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Right now works only on x86, filed bug to address all architectures
(ZEP-1414).
Change-Id: Iba53b3688b2b78a4189df0b50578070a8d2ac8b2
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This test was not using any legacy APIs, so simply
removed legacy from conf and ini's.
Jira: ZEP-932
Change-Id: I5a4b475ac5056b6d6aa64baef6bda53f20d8548e
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
This change ports tests/legacy/benchmark/sys_kernel stuff to
use unified APIs.
Change-Id: If6fbaa5586502205e9f4dc6e79ff1c1a1c1b8102
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
These were part of latency_measure benchmark, but was
used in all benchmarks.
legacy symbols in timestamp.h were replaced to unified
ones. Tick based checks have been replaced with ms based
checks in line with the new APIs.
Change-Id: I1d27310023be4cafbceccf50cb87d72b6681443d
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Instead of using a hard-coded string, make the sample use the Kconfig
variable for the device name.
Change-Id: Ib09f594e1cba221f9064318572bd90d38bd2733a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Change BREDR_NAME to DEVICE_NAME so it can also be used as the LE
device name.
Change-Id: I9ef55d9dff098372d47d9d5754ad7a7163a65bc0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The for loop could exit with a out of bounds (variable j) value for
the delayed_threads array, we verify for the variable value before
operating on the array
This issue was reported by Coverity
Coverity-CID: 160078
Change-Id: I6aa1cc325cc363be48cd72b2a58d0a55ec3854bc
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Option CONFIG_NET_IPV6_NO_DAD is not used anymore, clean project
configuration files.
Change-Id: I368e076d2f79f1d4bc86edee11ff5befe37362c8
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Routing tests uses ND so do not disable it, otherwise tests might fail
if disabling ND supported.
Change-Id: Ie020de8dac4447931d1067f1ed781a72cf05e8af
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The cause for this change is TCP. Until now, the radio strategy driver
(ALOHA or CSMA) was providing the actual nbuf, and not the buffer
fragment, counting on the fact that the loop was using
net_buf_frag_del() which made so, iteration after iteration, buffer
framgent to be always buf->frags. The problem with this logic is loosing
the fragments that might be still referenced by TCP, in case the whole
buffer did not make it so TCP can retry later and so on.
Instead, TX now takes the nbuf and the actual frag to send. It could
have been working with just a pointer on the data, and the whole length
of the frame. But it has been avoided due to possible future devices,
that will be smarter and run CSMA directly in the hw, thus it will
require to access the whole buffer list through the nbuf.
Change-Id: I8d77b1e13b648c0ec3645cb2d55d1910d00381ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The option is no longer used so it can be removed.
Use CONFIG_NET_IPV6_ND option instead.
Change-Id: Ibaa3d3deb52b8b176e85f8b9e1d8c80c1026aea1
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use printk(), snprintk() instead of printf() and snprintf().
CONFIG_STDOUT_CONSOLE is anyway disabled by default so printf()
will not output anything without it.
Change-Id: I5899741df2e187dae7b4602d074e9b4cbb9952aa
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The debug config was incorrect.
Change-Id: Id32cbcfb809acc9e4ab202b401d25e41a7531c42
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
We're using SPDX tags for Apache 2.0 licensing instead of the
Apache 2.0 boilerplate comment block.
Change-Id: I9e56f918ab4ed4d127dbe64538c9fa62886386a8
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Remove dev driver and integrate it in the default pinmux driver.
Jira: ZEP-958
Change-Id: I55670240f8a21749d3a6ae22e300e16ba80a2fb6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
According to include/gpio.h, GPIO_INT_LEVEL is 0,
which means the branch to test GPIO_INT_LEVEL is
always false and GPIO_INT_LEVEL cases will always
pass.
This patch also fixes another minor bug in main.c.
Coverity-CID: 160074
Change-Id: I1fefa978e65bf801f244b4c2960cb87a26b0829e
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
According to Coverity, rand() is a risk function.
So we use another method to generate random value.
Coverity-CID: 160070
Change-Id: Icb7e06cd43cb8bade6596cc37e9d04bfc59e1de7
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
In RISCV, stack always grows by a multiple of 16 bytes, even if we are saving
data of size < 16 bytes onto the stack.
Hence, for riscv32 architecture increase stack size to 512 for
threads_customdata, otherwise we experience stack overflow.
Change-Id: I805bc346b8a2c2f4ad6d0db622eb262290af942b
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
In RISCV, stack always grows by a multiple of 16 bytes, even if we are saving
data of size < 16 bytes onto the stack.
Hence, for riscv32 architecture a bigger stack size is required for
test_mpool_concept, otherwise we experience stack overflow.
Change-Id: I938aa511efcae66f0131fa1bc23bd68600421885
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
When trying to build with newlib we get:
hci_driver.c: In function 'hci_driver_open':
hci_driver.c:389:10:
error: format '%d' expects argument of type 'int', but argument 2 has
type 'uint32_t {aka long unsigned int}' [-Werror=format=]
BT_ERR("Required RAM size: %d, supplied: %u.", err,
^
This is because we have different types for {u}int32_t between newlib
and mini-libc. We have to decide how we are going to handle this going
forward. Various options include use of PRIu32, making mini-libc match
newlib's types, disabling the -Werror=format, etc.
Change-Id: I5df8fa05dd7658e1f6b2eeb8fa84e3270f3dd208
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
"struct k_mbox_msg mmsg" should be initialized before using.
"int" value returned by k_mem_pool_alloc() should be checked.
Coverity-CID: 160083
Coverity-CID: 160470
Change-Id: I35714bf9d76723c5fdd8c2963bf76b42ae1b1867
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
assert should not contain "i++" which might work differently in a non-debug
build.
Coverity-CID: 160469
Change-Id: Id8fd50127dd93de1676b812ac0888c9ec2e1b5de
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
"int" value returned by k_mem_pool_alloc() should be checked.
Coverity-CID: 160471
Change-Id: I7ec19147e7a51997fed890075b06eba30bef9126
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
This patch changes Quark SE power drivers to support multicore scenarios
e.g. both LMT and ARC core are enabled and manage power.
Handling LPS states in multicore scenarios are dead simple because LPS
states are core-specific states. It means that putting the LMT core in
LPS doesn't affect the ARC core, and vice-versa. DEEP_SLEEP state, on
the other hand, affects both cores since it turns power off from the SoC
and both cores are shutdown. It means that if LMT puts the system in
DEEP_SLEEP, ARC core is shutdown even if it is busy handling some task.
In order to support the multicore scenario, this patch introduces the
SYS_POWER_STATE_DEEP_SLEEP_2 state to both ARC and x86 power drivers.
On ARC, this state works as following:
1) Save ARC execution context;
2) Raise a flag to inform the x86 core that ARC is ready to enter in
DEEP_SLEEP;
3) Enter in the lowest core-specific power state, which in this case is
LPSS.
On x86, DEEP_SLEEP_2 is very similar to DEEP_SLEEP. The difference relies
in the post_ops() which calls _arc_init() in order to start ARC core so
it can restore its context.
This patch also adds the test/power/multicore/ directory which provides
sample application to x86 and ARC cores in order to easily verify the
multicore support. In test/power/multicore/README.rst you can find more
details regarding the applications.
Jira: ZEP-1103
Change-Id: Ie28ba6d193ea0e58fca69d38f8d3c38ca259a9ef
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
"ret" returned from k_msgq_put() should be checked.
Coverity-CID: 160084
Change-Id: I192db3a67ab9489e8338f6636d4c2a6935e98d74
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
This avoids asm files from having to explicitly define the _ASMLANGUAGE
symbol themselves.
Change-Id: I71f5a169f75d7443a58a0365a41c55b20dae3029
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
The K_<thread option> flags/options avaialble to users were hidden in
the kernel private header files: move them to include/kernel.h to
publicize them.
Also, to avoid any future confusion, rename the k_thread.execution_flags
field to user_options.
Change-Id: I65a6fd5e9e78d4ccf783f3304b607a1e6956aeac
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
Convert testcases to use the CMSIS NVIC APIs or direct NVIC register
access rather than the internal ones so we can remove them in the future.
Change-Id: I2a5a3eae713e66944cf105e7fffa603b88522681
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
_NvicSwInterruptTrigger is only utilized by a testcase for irq handling
on ARM-V7M. Just put the code into the testcase so we dont need to
support an additional interface.
Change-Id: I763c63c32a7a52918250458351d08b8fa54069dd
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some new tests were added that had the Apache 2.0 boilerplate licensing
instead of the SPDX licensing tag.
Change-Id: I4bde8c9c6e7a6d44bceeffb6bbcff9f62d417648
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
It is useful that the user API can know whether the connection
was established properly or not. So this commit adds status
parameter to connect callback in net_context API.
The call to connect callback needs to be set properly in TCP
code. This commit does not fix the connect callback call which
is not properly done right now in net_context.c.
Change-Id: I284a60ddd658ceef9e65022e96591f467a936a09
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the prefix length % 8 is not 0, then the remaining
bit length was calculated incorrectly and the prefixes
were claimed to match even though they might not be the
same.
Adding a test cases for testing this properly.
Coverity-CID: 157591
Change-Id: I9cb5a73d5cc211ec183176400fa5e2dfd209e2da
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
- Introduce NET_LINK_ADDR_MAX_LENGTH which is either 6 or 8
depending on whether CONFIG_NET_L2_IEEE802154 is used
- Instead of being a placeholder single index array of uint8_t,
let's use NET_LINK_ADDR_MAX_LENGTH to assign the size of the
"addr" array field in the net_linkaddr_storage structure.
- Now that the "addr" field of net_linkaddr_storage contains the
true size of the link address, we can remove "storage" field
which was hard coded to 8 bytes (2 uint32_t's).
- Fix 2 references to the "storage" field of the net_linkaddr_storage
structure.
Change-Id: I2ea12058280b289f65085964eb7d503d4fd260c2
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Add kernel pipe test cases which cover basic pipe apis usage
across thread and isr
Change-Id: I11899411b305535297f2e25056678d5b7df8fb95
Signed-off-by: jing wang <jing.j.wang@intel.com>
Add fifo/fifo test cases with unified kernel, which cover
basic apis across differnt contexts - thread and isr
Change-Id: Icb61d3dcd564167b0bd70419c652e0b000869959
Signed-off-by: jing wang <jing.j.wang@intel.com>
TestPurpose: verify memory pool concepts.
All TESTPOINTs extracted from kernel documentation.
https://www.zephyrproject.org/doc/kernel/memory/pools.html#concepts
ZEP-1210
Change-Id: I6250e4c26ddf361e74a76c23082cfdb376705560
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
TestPurpose: verify memory pool APIs.
All TESTPOINTs extracted from kernel-doc comments in <kernel.h>
ZEP-1210
Change-Id: I7dcc0638e7b9c4d6b5ffe282e4fe41ca520d003f
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
TestPurpose: verify API thread safe in multi-threads environment.
Thread safe test is explained with more details here:
https://gerrit.zephyrproject.org/r/#/c/9464/7/ test_mpool_threadsafe.c
Please comment if you think it necessary as an extensive kernel test.
Jira: ZEP-1209
Change-Id: I52a7ff393d72785622c047289e7d92286e131cc7
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
TestPurpose: verify memory pool concepts.
All TESTPOINTs extracted from kernel documentation.
https://www.zephyrproject.org/doc/kernel/memory/slabs.html#concepts
ZEP-1209
Change-Id: I95c6cd666212218b9928356f9439e67a2fcf9b73
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
TestPurpose: verify memory slab APIs.
All TESTPOINTs extracted from kernel-doc comments in <kernel.h>
ZEP-1209
Change-Id: I80bc85e96110e7106b3fc5883b982d71c6a7e50b
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
tests/kernel/mem_slab --> tests/kernel/mem_slab/test_mslab
For the purpose to hold other mslab test apps.
Jira: ZEP-1209
Change-Id: I4a72b02a0a5095bb7cfbf73396b6d003ea63f92e
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Coverity was warning about an array overrun that should never happen.
Add an extra check to verify that is indeed the case.
Coverity issue 152017.
Change-Id: Ie6269acaa85387ba051dbff87b4bfaab860517a6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Having TX buffers split into numerous pools has the downside of
increased memory consumption. This patch takes the initial step to
consolidate these pools into a single one, saving about 248 bytes of
RAM for a basic configuration.
Change-Id: I449ba18b44a9a6af68e9a2c44f19a9286eb88b14
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Added TICK_IRQ definition for CONFIG_PULPINO_TIMER and
CONFIG_RISCV_QEMU_TIMER
skip definition of HAS_POWERSAVE_INSTRUCTION for
CONFIG_SOC_RISCV32_QEMU, since it does not provide
power saving instruction.
Otherwise, not passing sanitycheck.
Change-Id: I2faa823226cd76d129d2bc3db961c9b862aaf784
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
Added TICK_IRQ definition for CONFIG_PULPINO_TIMER and
CONFIG_RISCV_QEMU_TIMER
skip definition of HAS_POWERSAVE_INSTRUCTION for
CONFIG_SOC_RISCV32_QEMU, since it does not provide
power saving instruction.
Otherwise, not passing sanitycheck.
Change-Id: I43a5c5112d694efdc14c5a0bcb4cafdc196d2680
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
The commit verify below PWM apis
pwm_pin_set_cycles()
pwm_pin_set_usec
test PWM apis under always-on, half-on and alway-off modes
Change-Id: I2251be23ad9c443703dac44e138651a63d2d7211
Signed-off-by: jing wang <jing.j.wang@intel.com>
Precursor patches have arranged that conditional compilation hanging
on CONFIG_CPU_CORTEX_M3_M4 provides support for ARMv7-M, rename the
config variable to reflect this.
Change-Id: Ifa56e3c1c04505d061b2af3aec9d8b9e55b5853d
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Merges the ksdk pinmux dev driver into the regular ksdk pinmux driver,
which now exposes the public pinmux API. Removes the private ksdk pinmux
API and converts the frdm_k64f and hexiwear_k64 boards to use the public
pinmux API.
Jira: ZEP-958, ZEP-1432
Change-Id: Ie5f60b604133093050b9c596050cad776d7b7cb3
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
A few CONFIG options got set twice in sensors_n_z.conf, remove the
duplicates as we get warnings associated with this:
warning: override: reassigning to symbol GPIO
warning: override: reassigning to symbol SENSOR
warning: override: reassigning to symbol SPI
warning: override: reassigning to symbol SYS_LOG_SENSOR_LEVEL
Change-Id: I7a723218db8e365bdb45c004e93bd2c4f55ab5ac
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This will replace the current goal of 'make qemu' with 'make run' and
moves Qemu handling into its own file and into the boards instead of
being architecture specific.
We should be able to add new boards that support some other type of
emulation (by adding scripts/Makefile.<emu type>) and allow the board to
define their own options for the use type of emulation.
'make qemu' will still work, however it will be deprecated, starting
with this commit it is recommended to use 'make run'.
Jira: ZEP-359
Change-Id: I1cacd56b4ec09421a58cf5d010e22e9035214df6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
These samples/tests fail to build on some of the nRF5x platforms. We
don't need Bluetooth enabled for these tests so we can reduce footprint
by turning it off.
Change-Id: I87e62a1d70f80d2bc22414d6a9e591e36ad9fa06
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
RAM size has increased on arduino_101_ble which causes it to no longer
be able to build test_controller_dbg.
Change-Id: Iab8ed2857db23d048cfa6b04e2d1fea31efbb13c
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some thread fields were 32-bit wide, when they are not even close to
using that full range of values. They are instead changed to 8-bit fields.
- prio can fit in one byte, limiting the priorities range to -128 to 127
- recursive scheduler locking can be limited to 255; a rollover results
most probably from a logic error
- flags are split into execution flags and thread states; 8 bits is
enough for each of them currently, with at worst two states and four
flags to spare (on x86, on other archs, there are six flags to spare)
Doing this saves 8 bytes per stack. It also sets up an incoming
enhancement when checking if the current thread is preemptible on
interrupt exit.
Change-Id: Ieb5321a5b99f99173b0605dd4a193c3bc7ddabf4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Add global option for legacy configurations and enable by default for
backward compatibility. Disable option on tests and keep it on legacy
samples and tests.
Jira: ZEP-964
Change-Id: I0831e2aa74d438b1ac74eb762186cb220a504beb
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Disk IO functions are used by both FS and USB Mass Storage.
This patch refactors those from FS directory to a separate one.
In addition existing, config options were modified to make
stuff meaningful.
Jira: ZEP-1276
Change-Id: Ia2a2e18f3dbbbdb964c3dc0427d8138ad86134cd
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Remove legacy option and use SYS_CLOCK_EXISTS where appropriate.
Change-Id: I3d524ea2776e638683f0196c0cc342359d5d810f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The source address for a TCP SYNACK must (obviously) be the same as
the destination address of the SYN that produced it. But the existing
IP packet creation routines would simply fill in a default address
from the net_context struct, which is correct for *established*
connections, but for the listening socket is generally INADDR_ANY
(i.e. all zeroes) and will result in an arbitrary choice for source
address (e.g. a link-local address on the same interface) which can
easily be wrong.
So we need to pass the correct address all the way down from the SYN
packet handler code through the net_ipv*_create() packet creation
functions. This requires lots of API plumbing, but relatively little
logic change.
Change-Id: Ic368f8cef6689f8a27cbafd5933a4964d5cc457e
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Add Kconfig configuration and conditional compilation of
RSSI measurement during a connection.
Change-id: I5a2f23f76a7cbbd9569d53d31899a472bf39d3ee
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig configuration to conditionally enable Data
Length Update procedure support in the Controller.
This will save CPU time, flash and RAM, if this feature is
not desired.
Change-id: I4515c0c7cf9aeb333a289397ae3c9bac04a08e4e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig configuration to conditionally enable LE Ping
feature in the Controller.
This will save CPU time, flash and RAM, if this feature is
not desired.
Change-id: I5fbbdbe8f45ac01c9b0d7b11e002a0d1db4d272e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add a test configuration to build a controller that
supports only Bluetooth v4.0 features.
This is copy of prj_controller.conf, but Kconfig defines
will be added in subsequent commits to conditionally
compile out feature not in Bluetooth v4.0 specification.
Also, added nrf52840_pca10056 and arduino_101_ble board
builds be tested.
Change-id: I36891bfc54cc36a8588c9b019de582e3193e8aa3
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
This helps simplify code that was previously combining net_buf_add()
with memcpy().
Change-Id: If44cf9cd651aba5e544e36567869f147468663eb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Stack for fiber idtSpurFiber at tests/legacy/kernel/test_static_idt
for nanokernel is not big enough since printk parse context refactor
(commit 3ab6046), causing sanity check to fail with CONFIG_DEBUG=y.
Change-Id: Iddc74a2800163a22be985067ce828ac859ae4a24
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
By default, when a 'fatal fault' message is seen in the output of any
testcase, it is consider an inmediate fatal condition and the test
case is aborted.
However, this testcase is provoking the situation to verify the
condition is caught. This, it shall NOT be considered a fatal fault
and the default overriden to allow it to proceed.
This was done in the legacy testcases and now is moved to this
testcase, ported from legacy.
Change-Id: Icac6cf55cae2ffd9b071e9dd1f35918b7b30de5e
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Stack for task tStartTask at tests/legacy/kernel/test_sema/microkernel
is not big enough since unfied kernel was enabled by default for all
test (since commit c2de216).
Change-Id: I3332cd5e14ca384428834697a1841fa680a68b00
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Fix build error (picked by GCC 6.x):
error: ‘stack_size’ defined but not used [-Werror=unused-const-variable=]
Change-Id: I402324fedaea9d0a10ee6533ba957ce18fa0fb83
Signed-off-by: Juro Bystricky <juro.bystricky@intel.com>
To customise test builds and support test related features such as time
stamps and a boot banner, introduce a Makefile variant that is dedicated
to testing.
Initially we introduce a new config overlay that is used for all tests, in
this case we enable BOOT_BANNER and BUILD_TIMESTAMP. This will print the
current version and the date, useful when reporting bugs and also an
indicator that the system has booted before the test has started.
For example:
[QEMU] CPU: qemu32
***** BOOTING ZEPHYR OS v1.6.99 - BUILD: Dec 21 2016 19:57:13 *****
tc_start() - Test Nanokernel CPU and thread routines
Initializing nanokernel objects
...
..
Change-Id: I224318cdeb55a301964ea366dbc577e2e3a09175
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Let's make net stack having its own level of debugging through sys_log.
It replaces NET_DEBUG by NET_LOG_ENABLED, which is then semantically
better: someone wanting to log the errors might want that not only for
debugging.
Along with it, CONFIG_NET_LOG_GLOBAL option is added, in order to enable
all available logging in network stack. It is disabled by default but
might be found useful when warning/errors need to be logged, so it is
then unnecessary to selectively enable by hand all CONFIG_NET_DEBUG_*
options.
It is possible, locally, to override CONFIG_SYS_LOG_NET_LEVEL by setting
the level one want to NET_SYS_LOG_LEVEL. This can be useful on samples
or tests.
Change-Id: I56a8f052340bc3a932229963cc69b39912093b88
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
quark_d2000_crb does not build as ROM and RAM space are way too little
for it.
Change-Id: I1a5992dcd49f90fa6604cd8ab76db7e170be7cd4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add a test for the available space for the payload, so the problem with
the payload length doesn't regresses.
Change-Id: Ifef541d8428947eb482729aa773a7e9ddd2b6f81
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
It will be thus possible to enable only the error logging, or the other
sys_log levels.
Change-Id: I0c0ed789f7cfbb4811320e8f8249151288274873
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fixes:
error: format '%u' expects argument of type 'unsigned int'
Change-Id: I02aaaea79150967d7831d89d0c05427bf2685708
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This moves the shell component into its own subsys and groups all
related files and options into a single place.
Additionally, one Kconfig option will now be required to enable the
shell:
CONFIG_CONSOLE_SHELL=y
The header files was also moved to include/shell/shell.h and can be now
referenced with
#include <shell/shell.h>
instead of
#include <misc/shell.h>
Updated documentation as well.
Change-Id: Iffbba4acfa05408055e9fd28dffa213451351f94
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
the commit include 5 ztest cases, cover the basic gpio APIs
including callback relevant and pin read/write functions.
It proves workable on intel quark c1000 and
arduino 101 platform
Change-Id: Iab30aa841cfa440c1f773b5a8c5ce0d68346c353
Signed-off-by: jing wang <jing.j.wang@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
the commit cover below apis by testing callback under RISE polarity
*) aio_cmp_configure
*) aio_cmd_disabel
Change-Id: Idc9ec3a2694950d0074b69d164ee2c1edac35c9a
Signed-off-by: jing wang <jing.j.wang@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
the commit cover basic message queue api testing across contexts
and some typical scenario
Change-Id: I82bb0c6a5df9d4436f5a98f78d1ad989e32282c8
Signed-off-by: jing wang <jing.j.wang@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
add semaphore test case which cover basic sema apis
across thread/thread and thread/isr contexts.
Change-Id: I2041969fcdc70a4dfc95438f067fbef8ebb31b19
Signed-off-by: jing wang <jing.j.wang@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
add unified kernel mutext test cases which covere basic
mutex apis under different conditions - timeout,
no_wait, forever
Change-Id: Iaab5bba80a6eebd89bfe675352d67b27024ad7bb
Signed-off-by: jing wang <jing.j.wang@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
add stack test cases which cover basic api usage across
threads and thread/isr.
Change-Id: I1f42fa1139899c932a14da18753b93972f561bc8
Signed-off-by: jing wang <jing.j.wang@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In unified kernel, memory maps are renamed as memory slabs.
This change ports tests/legacy/kernel/test_map stuff to
use unified APIs.
Change-Id: Ibf4d60fb53e45a119e6828a09f2638ee7def76b7
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is the port of the legacy/kernel/test_critical test case to
the unified kernel, and to use the ztest framework
Change-Id: I10834cbb51446b4a12fc680c0b65438d550f4d85
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is the port of the legacy/kernel/test_context test case to
the unified kernel
Change-Id: I344ac240eb3b48042477f8875115fdc3fca1154a
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The commit cover Interrupt Reset mode and Reset mode by 2 test cases.
They can't be tested in one shot, but need test separately.
api converage:
wdt_enable()
wdt_disable()
wdt_set_config()
wdt_get_config()
Change-Id: I44b20cfe97d860e8b25b2cab76f9d9398cfd8e69
Signed-off-by: jing wang <jing.j.wang@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
the test include 2 ztest cases, verfy below apis:
rtc_enable()
rtc_disable()
rtc_read()
rtc_set_config()
rtc_set_alarm()
rtc_get_pending_int()
Change-Id: Ifca2541312c5ec8d450803f1b6e4f5064098e7fe
Signed-off-by: jing wang <jing.j.wang@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This test case is under test set "lifecycle" against
https://www.zephyrproject.org/doc/kernel_v2/threads/lifecycle.html
Change-Id: I0d43c1a1798411c786efc45d76e6fd7c024c47dd
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change-Id: Iaadba1a720130a496a83c245c7da4b95dff168fd
Signed-off-by: Sharron LIU <sharron.liu@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This allows to specify length of discovery from command line.
Change-Id: I3ad80e74b5cdc263e549ce309b75c1f5c117b653
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Make the buffer length for tx and rx are the same for
spi_transceive API call. QMSI only supports equal length.
This is clearly specifed in spi header file.
Also correct some coding style issues.
Change-Id: Ifd34683e8813dae9b692ad453176a93cb3848427
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
From code inspection, the driver always took timeouts in milliseconds.
The only sub-ms wait uses k_busy_wait(), which has microseconds
granularity, but its granularity does not depend on the system clock
tick rate.
Change-Id: If48363fd1fbeeb8e5ff0f0f2ca86e671d63bc571
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
the commit cover alert send and receive with 4 types -
DEFAULT, IGNORE, PENDING, CONSUMED which across thread and isr
context.
Change-Id: I41dae9ba2dc980bcd768f1220f55b5492bc8ae37
Signed-off-by: jing wang <jing.j.wang@intel.com>
Move logging out of misc/ to its own subsystem. Anything related to
logging and any new logging features or backends could be added here
instead of the generic location in misc/ which is overcrowded with
options that are not related to eachother.
Jira: ZEP-1467
Change-Id: If6a3ea625c3a3562a7a61a0ba5fd7e6ca75518ba
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
rename NANOKERNEL_TICKLESS_IDLE_SUPPORTED to
TICKLESS_IDLE_SUPPORTED and remove nanokernel occurances in Kconfig
files.
Make TICKLESS_IDLE depend on hardware that supports it.
Change-Id: I6a2e4fb0f7cf4b45475b48e71823ea089ee98759
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There are static initializer macros available for most kernel objects
which we should use whenever possible.
Change-Id: I496f4d05d26801eddd21fae53bdd4fcdc3246fe3
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Moved all libc Kconfigs to where the code is and remove the default
Kconfig for selecting the minimal libc. Minimal libc is now the default
if nothing else is configured in.
Removed the options for extended libc, this obviously was restricting
features in the minimal libc without a good reason, most of the
functions are available directly when using newlib, so there is no
reason why we need to restrict those in minimal libc.
Jira: ZEP-1440
Change-Id: If0a3adf4314e2ebdf0e139dee3eb4f47ce07aa89
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fixes this:
error: ‘zero_addr’ defined but not used [-Werror=unused-const-variable=]
...
Change-Id: I5b0baf597e62f3206e15638a63e129503b76b048
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
When going into DEEP_SLEEP mode, the ARC core now saves
its context. This includes:
- All core registers
- Stack pointer
- Program counter (restored by jumping to the restore code)
The arc reset code now checks if the GPS0 bit 2 is set.
This is similar to the behavior of the x86 core done by
the QMSI bootloader which is setting GPS0 bit 1 in order
to call the restore path instead of cold boot path.
The sample has been adapted in order to support the ARC.
Jira: ZEP-1222
Change-Id: I375f03b16b8a5fd1f07ead55cf7e4947d6290c9f
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Since the user data size is now stored in the pool there's very little
value in storing it as well per-buffer.
Change-Id: I17a99123b232423c52a2179b4eccd813728d51b1
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to keep the initialization process light-weight, remove
net_buf_pool_init() and instead perform the initialization of the pool
and buffers in a "lazy" manner. This means storing more information
in the pool, and removing any 'const' members from net_buf. Since
there are no more const members in net_buf the buffer array can be
declared with __noinit, which further reduces initialization overhead.
Change-Id: Ia126af101c2727c130651b697dcba99d159a1c76
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is only for use with custom destroy callbacks, so that the
application gets isolated away from the details of how exactly the
buffers are managed. This opens up the possibility of switching away
from k_fifo to potentially better solutions, such as k_lifo.
Change-Id: I0d8322fdec3500d8ae060ae471b9448aeaa4572a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Ethernet build-all test was not being filtered base on RAM size so
build step LINK was failing with "region `RAM' overflowed by 192
bytes" error when running daily sanitycheck.
Added filter so this test is not attempted for boards with smaller
RAM such as quark_d2000_crb, which was causing daily build failure
Change-Id: I4ed3bef4f1c78e83890331db34fb1f2b2b066414
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Restructure the RANDOM Kconfig to match the structure used in other
drivers with a single top level menu. Move the true random number
generators to appear first in the menu, with pseudo generators at the
bottom. Do not present pseudo generators if a true random generator
is presented.
This change implies that tests, samples and applications that require
the random driver interface must now select CONFIG_RANDOM_GENERATOR.
In order for tests and samples to build (and run) on platforms that
have no random driver it remains necessary to select
the CONFIG_TEST_RANDOM_GENERATOR.
Note that CONFIG_TEST_RANDOM_GENERATOR retains its original purpose of
enabling a random driver that delivers non random numbers for the
purpose of testing only.
Change-Id: I2e28e44b4adf800e64a885aefe36a52da8aa455a
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Remove CONFIG_TEST_RANDOM_GENERATOR from each test and sample where it
is not required.
Change-Id: I949f8e93c2cb1881622a5e48efeb87c43122a170
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Until now it has been necessary to separately define a k_fifo and
an array of buffers when creating net_buf pools. This has been a bit
of an inconvenience as well as blurred the line of what exactly
constitutes the "pool".
This patch removes the NET_BUF_POOL() macro and replaces it with a
NET_BUF_POOL_DEFINE() macro that internally expands into the buffer
array and new net_buf_pool struct with a given name:
NET_BUF_POOL_DEFINE(pool_name, ...);
Having a dedicated context struct for the pool has the added benefit
that we can start moving there net_buf members that have the same
value for all buffers from the same pool. The first such member that
gets moved is the destroy callback, thus shrinking net_buf by four
bytes. Another potential candidate is the user_data_size, however
right not that's left out since it would just leave 2 bytes of padding
in net_buf (i.e. not influence its size). Another common value is
buf->size, however that one is also used by net_buf_simple and can
therefore not be moved.
This patch also splits getting buffers from a FIFO and allocating a
new buffer from a pool into two separate APIs: net_buf_get and
net_buf_alloc, thus simplifying the APIs and their usage. There is no
separate 'reserve_head' parameter anymore when allocating, rather the
user is expected to call net_buf_reserve() afterwards if something
else than 0 headroom is desired.
Change-Id: Id91b1e5c2be2deb1274dde47f5edebfe29af383a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Disable MDEF option and set it only in legacy projects.
Change-Id: I2e1f011eb1f876af929140e36f71f0efb5e955c1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The random driver, if enabled, is initialized by the kernel
initialization function. There is no need for applications or tests
to re-initialize the driver.
Change-Id: Ib4712dda937a7a83a8079c8aa662cec03c5416f8
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Stop using the specific k64 pinmux driver by default and start using the
more generic ksdk pinmux driver instead.
Jira: ZEP-1393
Change-Id: Id65b59518c386e6ba33cfa5c4c5bd541664d2b41
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This is used to disconnect a dlc.
Syntax:
>br-rfcomm-disconnect
Change-Id: I8f345d9fbb1f1f84bfb1f697322d9a87ff531797
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
There's now snprintk available that's more light-weight on the stack
than snprintf.
Change-Id: I6b3e4409703ca92fe6b8f4146ff47c490ab826cb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These correspond to the libc snprintf and vsnprintf APIs.
Change-Id: If3944972ed95934a4967756593bb2932c3359b72
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Not enough memory on this device with 8K of SRAM
Change-Id: I359cce806098cac7e0e2a9e00ce40c91bc535c5b
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch introduces a test that verifies the behavior of
CONFIG_RUNTIME_NMI at runtime.
The test is meant to be only for ARM Cortex-M targets.
Change-Id: I805a88e67fe47d396ac9e29e1275e5452a4b8a36
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
* Moved networking code into subsys/net.
* Renamed net/yaip to net/ip at the same time.
* Fixed the tests/net to compile
* Fixed the Makefiles and Kconfig files in subsys/net
to use the new location of the IP stack
Change-Id: Ie45d9e8cb45a93fefdf969b20a81e3b1d3c16355
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Check that we change the ll address in neighbor cache
properly when receiving NA.
Change-Id: Ib0373751abebdfe1c5e83fd38ec91b9587797e32
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Peer address is used when sending NS so that it is added
properly to neighbor cache.
Change-Id: I51c2e236a0b137f7ab086a782f3baced13aa3ee3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Also disable prefix lifetime overflow test as it does not work
properly.
Change-Id: I54c8716f6a6d4f5bec76b0a61fe0e18e983924f4
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the native IP stack is now the default, there is no need
for corresponding Kconfig option.
Change-Id: I08e4992f540f928a2b7378e8803e634e38725348
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit removes the legacy Contiki based uIP stack.
The new native IP stack must be used after this commit.
The commit also removes following things:
- legacy cc2520 driver
- legacy ethernet drivers
- legacy IP stack samples
and changes these things:
- disabled tests that only work for legacy IP stack
- select new IP stack by default
- enable random number generator by default as it is needed
by the new IP stack
Change-Id: I1229f9960a4c6654e9ccc6dac14a7efb9394e45d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Current reassembly of 802.15.4 packets works only if fragments are
in correct order. But as per RFC 6282 reassembly should be based on
offset parameter in fragmentation header.
Change-Id: Icdcb10b9aa8f5837063b0201a64f8eb050c75681
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
There were different tags defined in testcase.ini files for
networking tests. Unify these and change the tag to "net"
in all networking tests. This makes it easy to execute
all network tests via sanitycheck.
Change-Id: I8ce7ccf8cccca35234602e37f6568db0b986d181
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_buf tests were including net_ip.h which requires some
extra config options to be usable when the new native IP stack
is used. In order to avoid this dependency, define struct in6_addr
locally in the source file.
Change-Id: Iafe0d2b5b507665baaed23f5e2c55a9d9a300d47
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Which happens only when internal DEBUG is set to 1
Change-Id: I175943f32065ae81b1a4453dde40f36738c28084
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of having to write "NET_TCP_BUF(buf)->flags & NET_TCP_CTL"
every single time, provide a NET_TCP_FLAGS macro that expands to this
expression.
Change-Id: Ie876c538599fabae6b800a53613b6ad17dc45620
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Dropping legacy API. This commit also contains updated
unit tests in order to pass the test.
Change-Id: Ibc7426837e2f4f23bb5f3ed3719635c5c3d0ed0f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds the frdm_k64f board to the testcase.ini while list.
It also updates the README file with the build instructions and
firmware version used in this test.
Change-Id: Ia0e989d483aede51aa53e7453bbd1c260223372d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
More logical place for net_ipv6_unspecified_address() is in ipv6.c
instead of net_if.c. Removing the net_if_ipv6_unspecified_addr()
variant as it is no longer needed.
Change-Id: Ib5b4f6748030a8bf50fb848a87eef2968e2bcbc8
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adapting all unit tests so:
- main task's prj.mdef is already provided by unified kernel with a
default stack of 2kb.
- unified is the only kernel to be used now, removing unecessary kernel
type make option.
- removing all NANOKERNEL/MICROKERNEL related #ifdefs and so on.
Change-Id: I9b853dbd2aef971d355188cbf7fe2ececaaa80c1
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This creates a `struct net_conn_handle` that's only used as an opaque
pointer. The purpose is to avoid assigning a void* to a void** in
connection registering/unregistering functions, avoiding a
previously-caught bug by issuing an incompatible pointer types warning:
warning: passing argument 7 of 'net_tcp_register' from
incompatible pointer type [-Wincompatible-pointer-types]
Suggested by Andy Ross in 5beec6. This particular commit didn't catch
any bugs, but the one caught in 5beec6 wouldn't exist if this were in
place at the time.
Change-Id: I5c13fb4c5826adce6397feb7b400d36e426c4a87
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Added a test to send HBH option to IP stack. Currently
the test will always pass, activate some more debugging
to see what the IP stack is doing with the option.
Change-Id: Id0ab1590eb8216f5f67c4d43ce2e882186334198
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This can be used to store routing protocol specific data
into neighbor entry. By default no extra data is allocated.
Change-Id: Iabff0a1df676398a47b86adbc398c4f566dcc40a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Microkernel test for 6lo was giving error because the
prj.mdef file was refering to wrong function name.
Change-Id: I4197c509fb266a908eb03cc0bda34e39c66b229c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
fragment is only about testing 15.4 6lo fragmentation, so let's put it
in dedicated tests/net/ieee802154/ directory.
Change-Id: Ib838600e571753ab976c74dac78ee774f628c2ab
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
So reordering files in order to put more specific tests in it.
Change-Id: I000bc5efb8442d02e9a50e1b85cb45e0bec12789
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
No reassembly logic is changed besides removing the final reassembled
pointer. Instead of requiring such pointer, let's just use the frag one.
Such changes will ease the usage of ieee802154_reassemble():
the given frag buffer, in case it finally got reassembled and thus
provided a NET_CONTINUE verdict, will directly be handled by net_core.
This makes things consistent as well with verdicts:
- in case of NET_OK, buf has been consumed and thus unrefed
- in case of NET_DROP, buf needs to be unrefed by caller
- in case of NET_CONTINUE, buf is updated with reassembled and
decompressed data packet, up to net_core to handel it accordingly.
Change-Id: Ibd1588debd22a7f4571b36713dd46bf8b1d88329
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As soon as fragment is put into the cache and as long as it is not
identified to be the last one: let's return NET_OK to notifiy the
fragment has been consumed by ieee802154 L2.
That way, net_core will not try to interpret it - and fail - unnecessary
increasing the drop statistics.
On the contrary, once the buffer is fully reassemble, let's return
NET_CONTINUE in order to let net_core consume the buffer relevantly.
Change-Id: I715b687e451f4643656e122b0d119f114696340b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Buffer sent by 802.15.4 L2 might have more than one fragment, thus
handling it properly.
Change-Id: I12fef8a9c5de56615c3a084c57f438e71b320fcf
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Since "22e919872206b1d net: Adapt to new behavior of net_buf_frag_add"
net_buf_frag_add() takes onwership of the fragment, so this _unref()
after a net_buf_frag_add() is wrong.
Change-Id: I1559c2978cf8d800891d6e752478537fbee7c02b
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This enables the tests for the observer feature to be run using the
native IP stack.
Change-Id: I325dcd1f5d9fffe3821eed1bd950a717e5f17b67
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Earlier test results was updated as soon as test server ACK client
dhcpv4 request. But update results on IPv4 address add event on
interface.
Change-Id: I212309a4d1d2eae88f73470e00754db1d6fecda5
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
RFC2131 requires that a client must choose XIDs in order to minimize
the chance of collision with another client. Selection of a random
XID at boot is a valid approach. Adjust the XID representation from
array of bytes to the more convenient uint32_t representation,
initialize the XID to a random number and increment for each request.
Refactor the dhcp test case to generate response messages with the XID
from the received message.
Change-Id: I93f180e6aa02430f807e0a97186577dc956fb653
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The test "Test block sized transfer" does not work with
new IP stack so disable it temporarily for new stack.
This needs to be fixed later.
Change-Id: Ie89dd101270ab9b8a9b056757de79cd3da009180
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Rename project configuration to be architecture independent and do not use ARCH
in Makefile.
Change-Id: Ic793751e3187bc74fd14cec929754d691b01a799
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This provides only initial set of functionality tests
for TCP. More tests are to be written.
Change-Id: I157fed85f561523bf063732ce86eaae551c2d384
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Current net_nbuf_write() api just appends data to last fragment. And
doesn't write data based on offset. That's why renaming this api.
New net_nbuf_write() apis based on offset will be coming soon.
Change-Id: Ie8e13e5f6091a279b62b6d8b0b3928a5187e75b0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This ports zoap to the native stack.
Just for reference, and totally not scientific, here are the numbers
using the old stack:
$ size outdir/qemu_x86/zephyr.elf
text data bss dec hex filename
34657 10316 16916 61889 f1c1 outdir/qemu_x86/zephyr.elf
With yaip:
$ size outdir/qemu_x86/zephyr.elf
text data bss dec hex filename
30575 9148 6164 45887 b33f outdir/qemu_x86/zephyr.elf
Jira: ZEP-818
Change-Id: I7992a3e2af7d419081ee5a64d7cc2d49fb628ead
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Valid case:
1) If the offset is more than current fragment length, adjusts offset
from next relevant fragment and starts reading or skipping.
2) If the read or skip length is more than available data length,
then throw an error.
In case of an error, frag is 'NULL' pos is '0xffff'. Rest of the cases
are successful read and skip.
Change-Id: I88c4b85e14e5821f681966b5148ba9519b91cca4
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
RFC 6282, 3.1.1 (If SAC == 1 and M = 0, DAC = 1).
Source and Destination address compression support if addresses are
based on context based information from Router Advertisement message.
Change-Id: I23a3bf4f111016a8e54be5f0181a113353ad4b88
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Test is only for parsing 6CO data. Nothing more than that.
Change-Id: I7e5851f389216473379a9e50b83dfb03fbe1e68e
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The memcmp() could reach after the buffer that is used for verification
ends, which was causing this test to fail on the qemu_cortex_m3 board.
Change-Id: Ia05df823f201d9017acb35c7634fa506389ae9f1
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
linearize() expects the amount of room available in the buffer.
Change-Id: I1062912f76951758177b7dd6588e7e0ae280dc03
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Quark D2000 doesn't not have enough RAM for these tests.
Change-Id: Iba79eaadb15eb8f1eae4bfdbc6865985d3da3fd3
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Buffer leaks are fixed in 6lowpan compression and ieee802154
fragmentation. So lower the count in tests.
Change-Id: Ic9581f898156fedc20a3e445be8b7a466ee15d99
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
A fake network device and interface are setup. Test implies add and
removing an IPv6 address which should trigger the related notification.
Change-Id: I6035cfbfaf80c8f4352b5d31b47ca1445434d926
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
While doing some documentation for it, I realized names were not all
good and it missed some stuff:
- what belongs to event should contain "event" in it
- we have a structur as callback so let's type the handler as a handler
- let's add the request handler signature
Change-Id: I18822cbcdc3c10e33600d6db38abab5ca73a228c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use ?= for the CONF_FILE variable to match the default assignement for
BOARD ?= qemu_x86.
Change-Id: I0b6cf1e967eeb437d99aa7286cf560426d48fbf9
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
It mimics how event could be thrown through a dedicated thrower (a
fiber). The amount and event it can throw is gived through parameters.
Change-Id: I484bc72bdb730a77ce976b0b2998411d9918b7fc
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Basic unit tests for Router Advertisement message handler.
Change-Id: Ia99cd160632972a12e2099a3ff6e41e6ea48ff9b
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The buf parameter cannot point to a data fragment in
net_nbuf_write() because we need to use user data inside
that function and the fragments do not have that information.
Change-Id: I45b9c23869df08a0852bd99c0b453210ad2300b5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tests for net_nbuf_read, net_nbuf_write and net_nbuf_skip API's.
Change-Id: I77f702dda8c9df7892120f47ff03a6b256191d31
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
One second timeout seems to be too short as some test runs
fail when run in Jenkins.
Change-Id: Ifb01929148415961712468e3cc85387aac5eb2bb
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It's an empty beacon frame, juste to validate the Beacon frame parsing
logic.
Change-Id: I90916eb87187c9eae9b2267f34dc93bee554d4b5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If ethernet address is broadcast or multicast, l2 layer does not
send any ARP messages. Handle this scenario in ethernet tests.
Change-Id: I8e11832803e1539887152447090d1286c7fa3eb0
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If the connection establishment has an error, the accept
callback needs to be able to return that error to user space
so that the application can know about it.
This is especially important in TCP where application needs
to start to listen again if reset is sent during connection
establishment.
Change-Id: I55f36e4f101c7237c1288f09baf6e602b33da2b3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some of the DEBUG options for the new IP stack still used
the CONFIG_NETWORK_IP_STACK_DEBUG_ prefix.
Change-Id: I8f039ac5e303a7c571a870403ce17d758db540d5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
- new stack options are renamed and placed in their respective menus
- new stack Kconfig gets normalized (tabs vs spaces, etc...)
Change-Id: Ia68f6589fed464bbdd76dc0812775684b2f94a58
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add socklen_t addrlen parameter to net_context_bind(),
net_context_sendto() and accept callback.
Currently the address length option is not really mandatory
as we can figure out the length from the address family.
But if we are going to support other protocol address families
it might be needed.
Change-Id: I59206465c3259050c469c5b2150221646a9a08d7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Because of printk fixes in master, some of the networking
unit tests will fail in next merge.
Change-Id: I3e28aae72c0c10b402b78c0f406ecb3513b967a7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Earlier all unit tests are with IPv6 and UDP as next header.
Modified tests with IPv6 only, IPv6 + UDP and IPv6 + IPHC next
headers.
Change-Id: Ie02cecb37e07ceae8a06a0653e2ccdfe0db91239
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
We are not just checking the test build but this time
the tests are also run.
Change-Id: I7b0b24c51dfc2dc58f290cca7a593be431b8077f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For consistency as well as for helping when grepping etc.
Change-Id: Ib5e6b3369e510dd2b996f735d801c2b80291ad7f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is only meant for the new IP stack.
Change-Id: I643b0556f87423f09555274749db93397ef66c59
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Reassembly IEEE 802.15.4 fragments as per it's datagram size
and datagram tag. Uncompress IP header fragment as soon as it
arrives. Size matches only after uncompression of IP header with
total length.
Support added for multiple IP packet reception. Default is one full
IP packet at a time. Cache size can be modified via Kconfig option
(NET_L2_IEEE802154_FRAGMENT_REASS_CACHE_SIZE).
Note: If you increase the size by 1 means, you should have N number
of data buffers available at max.
e.g. One full IP packet (1280 MTU) needs 15~16 data fragments means,
multiply size by same number of fragments. It requires more memory.
Offset based reassembly yet to be done (fragments can come in any order
[e.g. mesh]). Now assuming that fragments are in right order.
Change-Id: I17baee30a1087eb9ec6dc25f03ed64bbe0df2917
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Add support for IPv6 header dispatch (without IPv6 compression
and uncompression). Only IPv6 dispatch header will be added at the
beginning of the buffer.
Change-Id: I7400a4dd115ac3b4b3d9deecd3cdb9ea292573fb
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
6lowpan compression and uncompression done on original
input buffer. So no need to return paramter as net_buf *.
If the compression or uncompression fails, unref the buffer
as it cannot be used further.
Change-Id: I64f496e22b2008a91a358fff65de1b87659cd9eb
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
UDP length was wrongly set and test count was hardcoded.
Change-Id: Iade959e1b8c3580b43aa2a9ff1fc10eb5a462f2f
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
- Parsing a proper ACK reply
- Generating a ACK reply from a data packet requesting it, and comparing
it to a proper one.
Change-Id: I1717fedc899eafa0aa849e1e253f02cd3dc3d4fc
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
First test is a unit test for frame parsing
Change-Id: I080d64a71fe4b6ff00e071a0cdee97ab9cd922d5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Allocate the right amount of space for L2's context.
Change-Id: Ia2f4f4162334e9e9c26dc95230abdfde5986e052
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is related to changes in commit 7dcbbc39e7
("build: move from srctree to ZEPHYR_BASE for app include paths")
Change-Id: Ie902ed66bb74188ed54aae44e2f4289f954ec351
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When a UDP packet has been received and if a watcher match
is found, then a callback is called. It is useful to have
a pointer to net_conn when calling the callback.
Change-Id: Ifa97b37c22b1fc9cac7eadfba23aa68dfd473fda
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the net_conn needs port information, use struct sockaddr
internally as it has the port numbers built in.
Change-Id: Idb1c87afa956dfe55dc8d533d867fa7845545b12
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
No need to print debug prints if debugging is not activated.
Change-Id: I42a6453b4f3e11106119561b580ebea41e56452d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When checking the IP address from network interface, return
also the used network interface.
Change-Id: If7b8385193da4cb1b469f697e219cfae3b6477dd
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
IPv4/6 functions follows this scheme: net_if_ipv<4/6>_<name>.
Applying that to net_if_set_gw/net_if_set_netmask which are IPv4
functions.
Change-Id: I2dcbb16ce81cfdffbfbb5cae24ad76ddf2b9919a
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Using macros does not let the compiler verifying about the type we are
providing, which usually give an error easier to understand.
Also, this will let the compiler deciding how to actually optimize
(inline or not) the code.
Change-Id: Iba49590b620ef0a1bd0ed5621453524fcfea747c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Disable IPv6 DAD and ND for IP address test as there is
no need to do neighbor discovery in the test. We also
would like to see network interface debugging and use
dummy L2 driver instead of ethernet one.
Change-Id: Ia9f218c8d4c13afa1482302691d2ef72af4a7b13
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The driver_api pointer was set to NULL and send() pointer
was missing which caused a crash in TX fiber.
Change-Id: I7204c975691476dd9ab2c61bfd11b7664343e47c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
ARP is IPv4 only so no need to have IPv6 functionality.
Change-Id: Ie70242f5763ba4945c311898643414851f7e8660
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
These tests will verify that we can successfully insert
some space in front of the net_buf fragment chain.
Change-Id: Idf52ed56c52d66268783fb4fecd44b70fc852734
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The driver_api pointer was set to NULL which will cause
a crash in TX fiber.
Change-Id: If1c9a1e44904970f3a0019741eaaad4bf62d2c73
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The tests will make sure net_nbuf_copy() works as expected.
Change-Id: I48dc3b794c70ec4d6436feb76508952c88bbf09b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The ARP unit test is not able to pass packets between fiber
and task. Because of this the test is run from fiber.
Change-Id: I1825a0abdc1b04a78de76d58425f4d2a2ce26ab7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The ARP packet header contained ethernet header. This is very
confusing so separate the link layer header. Fixed also the
unit tests to run properly.
Change-Id: I8b00bde280ad9f49494766370acb2a8e9cade033
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Now uses net_nbuf_ll() to point to link layer header.
Also the ARP req test passes properly.
Change-Id: If649ff19a064490bff33d03b4ce70ef11bfa7cd5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of using hard coded net_if, get the default network
interface using net_if_get_default() function.
Change-Id: I6248555ce57ae5196adea7baa9db325660a71255
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Right now there are tests for IP packet checksum calculation.
Change-Id: I1e9e72d01d4690728269c4484f8628350cf95729
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
These tests will check that caller is able to set IPv4 address
to a network interface and check if an address is one of the
assigned to a network interface.
Change-Id: I8aa748c40fbc02eef50ccf76d10a0057ef29021b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tests have issues right now so these will be activated later.
Change-Id: Ib5549f9ed5600a20b2cfddbddcde8e7f7b297eef
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
User should use the net_nbuf API that is supporting a concept
of RX, TX and DATA buffers, instead of using directly the net_buf
low level API.
Change-Id: I3b8f5f13cd37d42d2322a58b35573e117d520c54
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Having CONFIG_ASSERT=y and CONFIG_DEBUG=y was causing these tests to
overflow their stacks and crash.
Change-Id: Ibcd57abe044a2203d1a954a4c5755218af48f302
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Tag all legacy kernel tests and samples as such.
Change-Id: I43b24acb71c282ed14ff6e6ef06c9542bad86f6a
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Legacy FIFO operations were failing and thus the TC was failing to run.
Stop using k_fifo_get() for allocation and use a bitmap allocator. A
couple of the bitmap operations should be moved to a common header
once ZEP-1347 is completed.
Passes on all arches and boards, whitelist removed; ARM excluded
though due to missing bitfield implementation as per ZEP-82.
Note there is a false checkpatch positive in the decl of
sys_bitfield_find_first_clear().
Change-Id: I1d3ce8e988bf799573041026e419e3946d153590
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
snprintf() implements the ability to foce a negative value through the
(unsigned) size_t len parameter to allow the formatter to use a
maximum size string.
This is point less, we don't have as much memory and this is a recipe
for all kinds of vulnerabilities.
Kill the whole thing, the testcase it represents and thank Coverity
for finding this thing. Whatever use it had before, it has no more.
Change-Id: If422246548664699d8aa328a1b9304ef13cab7ea
Coverity-ID: 131625
Coverity-ID: 131626
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This patch provides a test that verifies the correct functionality of
CONFIG_RUNTIME_NMI at build time.
Change-Id: I92c8af78d327f6f2b8b87573dbf132068ff80a45
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This adds basic support for width modifier when printing integers.
Supported specifiers are u,i,d,x,X. Width '*' is not supported.
Flag '0' for left-pading number with zero is also supported.
examples:
printk("0x%x 0x%02x 0x%04x 0x%08x\n", 1, 1, 1, 1);
0x1 0x01 0x0001 0x00000001
printk("0x%x 0x%2x 0x%4x 0x%8x\n", 1, 1, 1, 1);
0x1 0x 1 0x 1 0x 1
This should make printk usable for pretty printing u8 and u16 integers.
Change-Id: I58fa869e9c295a052f97fbf052291ef4d132811e
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
This commit updates the pinmux test case application
to match with the hello_world sample app.
Change-Id: I86f459062527b7e2831bd7a3dfaf6bf8b28ef132
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Remove nano kernel references found at the README file.
Change-Id: Ib71a9a2900a5cb02a3b6038f74e51e5f860792be
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The app passes the index into an array storing power states
instead of the power state to _sys_soc_power_state_post_ops
Jira: ZEP-1341
Change-Id: I6ddf0a2dbadfd06aafbcafa88be7441e99694a51
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Enable this option to test any usage of structs and variables inside
macros.
Change-Id: I6ec64fb865e87fc0771ae10f0c4eb63f6144c88a
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The divide-by-zero test was using an uninitialized variable that
Coverity was unhappy about. Simple fix to just initialize to any non
zero value.
Change-Id: I9e5865a99e7a8eb3ee52421cc3dcb6717dca1ad1
Coverity-ID: 152053
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Coverity complained about the use of strncpy() to fill up a buffer of
size N with a string of the same size didn't leave room for the final
\0.
This is a valid concern; however, the usage is valid too, as the
writer intended to create a pattern that later can be tested--addind a
\0 would break the pattern.
So instead, use memcpy() for the same function.
Change-Id: If52d02ce41731348f4a2d750c79f9e1c51f3afcf
Coverity-ID: 151947
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Coverity complains about using an uninitialized variable; there is no
reason to do so; thus fixed to avoid maintaining a whitelist.
Change-Id: I657f9e7d46b1b9b091e36638c1951b93903fbec3
Coverity-ID: 152048
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This is not a strictly necessary initialization, as the data is not
used, but will keep Coverity happy. It being a testcase, there are no
size or speed penalties to the overall kernel and avoids having to
manage a whitelist for an issue in scanning tools.
Change-Id: I0ddcf43ca1114356d58f93de57232864246ffe07
Coverity-ID: 152052
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Coverity complained about the code using an uninitialized chunk of
memory; harmless, but fixed to avoid having to whitelist.
Change-Id: I5c890ff78fab2799b882b8e4a25c15476702d132
Coverity-ID: 152049
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Those tests are now build with unified kernel.
Change-Id: Idbc42bb77060cea0130d62cccdf2e40aeee89128
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Coverity detected some constant value in the vars, due to the
exclusive config select in the code.
Change-Id: Id27b658f3cd70dce626fef054457a9c726b3b957
CID: 151974, 151972 and 151971
Signed-off-by: Javier B Perez <javier.b.perez.hernandez@intel.com>
This commit fixes some style issues detected by checkpatch:
- Lines over 80 characters
- Comment block
Furthermore test legends are homogenized.
Change-Id: If92bbbdcf915164da945a60c8bcdbb7452ad0da0
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit fixes an issue in the test_ccm_mode.c file:
sizeof(data) is used to compute the length of the array pointed to
by the 'uint8_t *data' pointer.
At the same function scope, there is a variable (dlen) that already
specifies the required length, so we use that variable instead of
the 'sizeof' function call.
This issue was not reported by Coverity, although is worth to fix it.
Change-Id: I27cbf8c7000a4189a42d193f6445996d4b852aa6
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit fixes the dead code issue reported by Coverity.
Coverity-CID: 151977
Change-Id: Iaa31c032456f48e1af1d1c9d722f051ac5519ccf
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit fixes the dead code issue reported by Coverity.
Coverity-CID: 151975
Change-Id: I449341d1f540abe149e8ad9197a64d52cd5722cd
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit replaces spaces by tabs in the TinyCrypt AES test.
Three 'space required before the open brace' issues are also
fixed by this commit.
Change-Id: I27e961484899873a25847452d569b50322dba74d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit solves some style issues found in comment blocks.
Change-Id: I1f4f7344e33b5898ac7d1fb2cd13d75946b4ee5e
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit moves variable declarations at the beginning of the test
routines.
Change-Id: Id1382b64aad4130e9a939c5e51301b75c6958fe5
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit removes the declaration of a data type inside the tests
3 & 4. The new data type 'struct kat_table' is declared at the
beginning of the file.
Change-Id: I7662cd164a865fe0e70f984b9b494d96b4a72af9
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This fixes a string overflow past the end of a buffer
which was reported by coverity.
Coverity-CID: 152044
Change-Id: I5b331135e338fa43b5589a9488b06367e8cad5a7
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
A popular issue "format is not a string literally" was
caught by LLVM. Let's make it a string literally.
Jira: ZEP-1179
Change-Id: I2b4a5aef750b772504bf0e6f005dab2ff9ac3e7c
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Add function return value check. This was caught by
Coverity.
Coverity-CID: 151950
Change-Id: Iee550e15d124f05f0b0514fdad22d06c617beac2
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This commit solves some style issues found at the
tests/include/test_utils.h file:
- Lines over 80 characters
- Unused arguments
- Missing {} in if-else
Change-Id: Ifaee81ec7c57a250b2c368b2efda38dc69d02c81
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This issue was reported by Coverity (CID 151952)
Change-Id: I59a20a3ccbe606ef634db98ac6cc6889a3973ec3
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
testcase.ini was not building for ARC. This app would
run on x86 and arc.
Change-Id: I961d56079aa1db7d84e0fcc87780ba11d7f4d831
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
The variable type mismatching was caught by LLVM.
Jira: ZEP-1179
Change-Id: I37934ef2ee47c521a78086564876843794688d55
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
By default, when a 'fatal fault' message is seen in the output of any
testcase, it is consider an inmediate fatal condition and the test case
is aborted.
However, in all such cases, the testcase is provoking the situation to
verify the condition is caught. In this case it shall NOT be considered
a fatal fault and the default overriden to allow it to proceed.
Change-Id: Id4e9138e5f0fcb8cd77efbb1831897fb0946ba20
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This TC is only exercising the API, as we don't have a feedback loop
mechanism to verify whichever values are fed to the ADC.
Fixed the loop to complete after 10 runs; on each run, print the
values and actually report the difference between them. With no inputs
connected (aka: floating), they should be reporting noise relatively
close to the previous reading, so we might want to use this delta as a
testing pattern (assert if the delta is higher than some value, but
I've seen variations as high as 40M units). For now, the test is just
happy with being able to read them.
The buffer has been re-typed to uint32_t so we can iterate over it
without casting tricks -- it requires then only a single cast when
initializing sample.buffer (which shall be a void* anyway).
Duplicated the buffer, so we can flip/flop between two buffers to
compare against the entries read in the previous run.
v4: fixed missed warnings
Change-Id: If6b48b92231007202d74f5c042f6d0cf3fdcb60a
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This test case just exercises the PCI enumeration and there is no real
way to test success/failure other than running it and the kernel not
crashing.
Moved to ztest.
Retag so it is actually ran on QEMU/x86 and galileo once we deploy in
the HW pool. Note this means that we need to force CONFIG_PCI on
Qemu/x86, which can run this testcase.
Change-Id: I85b64800f7d989357927b4a25777041047293b34
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Move away from legacy APIs and use unified kenrel instead.
Change-Id: Icae86beec66df1b041405cbe3455913630fc8ad1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Switch left-over usage of TICKS_NONE and TICKS_UNLIMITED to the new
unified kernel counterparts K_NO_WAIT and K_FOREVER.
Change-Id: I2f2a16360e816f9f8791eb216deb3c70b8cc87df
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There was a lot of duplication between architectures for the definition
of threads and the "nanokernel" guts. These have been consolidated.
Now, a common file kernel/unified/include/kernel_structs.h holds the
common definitions. Architectures provide two files to complement it:
kernel_arch_data.h and kernel_arch_func.h. The first one contains at
least the struct _thread_arch and struct _kernel_arch data structures,
as well as the struct _callee_saved and struct _caller_saved register
layouts. The second file contains anything that needs what is provided
by the common stuff in kernel_structs.h. Those two files are only meant
to be included in kernel_structs.h in very specific locations.
The thread data structure has been separated into three major parts:
common struct _thread_base and struct k_thread, and arch-specific struct
_thread_arch. The first and third ones are included in the second.
The struct s_NANO data structure has been split into two: common struct
_kernel and arch-specific struct _kernel_arch. The latter is included in
the former.
Offsets files have also changed: nano_offsets.h has been renamed
kernel_offsets.h and is still included by the arch-specific offsets.c.
Also, since the thread and kernel data structures are now made of
sub-structures, offsets have to be added to make up the full offset.
Some of these additions have been consolidated in shorter symbols,
available from kernel/unified/include/offsets_short.h, which includes an
arch-specific offsets_arch_short.h. Most of the code include
offsets_short.h now instead of offsets.h.
Change-Id: I084645cb7e6db8db69aeaaf162963fe157045d5a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The unified kernel is now the only supported kernel, so this
option is unnessary. Eliminating this option also enables
the removal of some legacy code that is no longer required.
Change-Id: Ibfc339d643c8de16a2ed2009c9b468848b8b4972
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
tests: power_states app updated to support SoCWatch collection
Add CONFIG_SOC_WATCH option for enabling the SoCWatch
QMSI driver and associated instrumentation hooks.
Bug fix for soc_watch.c to use local irq_lock/unlock
This will be put into QMSI as well.
JIRA: ZEP-1121
Change-Id: I0514324e81ca02c1d01ffc2d6cf4d31aee491544
Signed-off-by: Jon Moeller <jon.moeller@intel.com>
This test does not work for cortex-m0+ yet, so make
it run only on m3/m4 for now.
Change-Id: I0a90335d264cf88f3a62057860d6f129085c558f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
convert all sensor drivers to use threads and the unified kernel API and
remove all legacy APIs.
Change-Id: Ica43ea74ecbbf85273f718f182c413a9dcd8abc6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The API to disable _sys_soc_resume notification is currently
called _sys_soc_disable_wake_event_notification. This is
misleading because it is possible that the ISR from which
_sys_soc_resume is called could be from a different interrupt
with higher priority that happened before interrupts were
enabled. More accurately, it is a notification of exit from
kernel idling after pm operations.
Jira: ZEP-1271
Change-Id: I83747f2cacac1bc17f135d12f4aa4478970fc02d
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
This test is not a kernel object test and does not use any legacy kernel APIs,
so declare it non-legacy.
Change-Id: I430ac296334dbb8ff2b2d6576f7007a5dcc6f546
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert fiber_start to k_thread_spawn and nano_fiber_fifo_put to
k_fifo_put.
Change-Id: If1ec405ec602e28a538f4c9569ede87519346559
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use defines from k_fifo intead of legacy API.
Change-Id: Ib8cf0d88240ef145da550b8cf83d2580e7140521
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Only net_receive() is using non-special value for net_buf_get_timeout
so this change is included here. Other users are using special values
which are already correctly handling ticks vs ms change.
Change-Id: Ib12d34ac5a546b36fa7b35615f082c82a256bd07
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Use new sleep API or remove sleeps where not needed.
Change-Id: I88c0973e57eb4970b68b3f4fa428683191b1a7f0
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
This can be used to initiate an outgoing connection
Syntax:
>br-rfcomm-connect <channel>
Change-Id: I7ac7aeb61e7ae7e3f55c7cd7e815bdb604b27fb3
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Restructure the Bluetooth options more logically.
- Both host and controller are now behind the same high level
CONFIG_BLUETOOTH.
- Selecting controller support disables other HCI driver selection, so
the controller isn't in the same list as HCI drivers any more.
- Under the top-level there's a "Custom stack" option, which when
enabled opens up the option of choosing CONFIG_NBLE.
There are various other cleanups and simplifications in this patch as
well, since splitting these up would have been fairly tricky while
making sure all test cases still build.
Change-Id: I5bb715cb9d20201cb8b72fbd149c8a09a4b2d7d2
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add Low Power States support to the power shim layer
and show the usage in the quark_se sample.
States are defined as follow:
- SYS_POWER_STATE_CPU_LPS: SS2 with LPSS enabled
- SYS_POWER_STATE_CPU_LPS_1: SS2 with LPSS disabled
- SYS_POWER_STATE_CPU_LPS_2: SS1 with LPSS disabled
Jira: ZEP-994
Change-Id: Ie4b93f6e539cb53fc035be00280b66b2cb0d9fea
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Leave the aon counter in running state after the test.
Arduino 101 loader assumes the counter is running.
Stopping the counter will cause the next app to
not start without a hard reset or power cycle.
Jira: ZEP-961
Change-Id: Ia88f0c642b1df8dc5e2b1ee6c55ff0618b6127d0
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Debug setting is using another mdef file that was no changed by
commit 5b1b2d6123
Change-Id: I406b45e37a112352c88629cf7d494c70784930aa
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Otherwise, local settings in the account will cause headache and
randomly alter the result of the testcase.
Change-Id: I758966a7fe9335a13ce237aea7d6df2ddc5733ce
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Reorganize the code tree so no forward declarations are needed
(basically, move main() to the bottom).
Retag as not build only so it can be run on Quark*
Convert to actually verify counter readouts are increasing /
decreasing over busy empty loops and the alarm is being called.
Change-Id: I746efe595b8d1ac4471dccc2e87f8b36f5cc8ebe
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
sanitycheck already sets this and we need to allow deprecation
warnings.
Change-Id: I3d6bf652403bcbdba47663c8cd0d17682a8a842d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add an Arduino 101-specific configuration that enables flash-based
storage support as well as the file system shell.
Change-Id: Ic10ea958dd2446df4942a8dfd3cce1e3368852b2
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Implement a new "clear" command to exercise the bt_storage API. The
command can either take an address parameter to clear storage for a
specific device, or, if called with the parameter "all", to clear the
entire storage.
Jira: ZEP-181
Change-Id: I1ebd17033f2062951abeeb7d7c448a34a3672577
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch removes "FAT" from files names, config names and
symbol names so as to avoid confusion, when other modules use
them in a more generic way.
Also flash_disk_access.c and ram_disk_access.c now exports generic
disk_access symbols as defined in include/disk_access.h rather
than FAT specific ones in fs/fat_diskio.h. Thus modules like
USB which need to use disk_access interface is not dependent
on symbols from ELMChan FAT module. Also fat_diskio.h
is removed.
Further the shim between ELM chan and Zephyr is modified as
per these changes.
Change-Id: Ifd80f14a629e467ee9c7a9aaff8a4896eed11982
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
This TC cover dma transfer with different channel and burst length
It support 2 ways to execute
*) full-auto: by default, it run all sub test cases defined in array
once flashing done and reset.
*) interactive: when CONFIG_CONFIG_CONSOLE_HANDLER_SHELL=y, it go into
shell first, user can input test command one by one for debugging.
move original test under drivers/dma to test_loop_transfer/
Change-Id: I7e78b730592c80bf2c23b20c8b0eb65a9b353acd
Signed-off-by: jing wang <jing.j.wang@intel.com>
The main task uses stack-hungry() printf(), and the switch to the unified
kernel pushed the necessary space over the edge.
Change-Id: I7b64e7f09d91c5050ffe7fb18506ff24289169fc
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
For systems that have both high base (CPU, bus, etc.) frequency and
small divider of the base frequency for system clock and this way,
do not allow 1 second period for the system clock, set the system
clock period to 0.1.
Change-Id: Iafb4604112d4adb8430f8bf57a5a31de3f6cf91d
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Since the mutex can not be unlocked if it is not locked, fix the test
and make sure that it unlocks the timer exactly same times as it locked
it before.
Change-Id: Ie29d308b789ed00f4fd3cf2faef3aa1f4bc89e3e
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
The SPI_0_CS_GPIO and SPI_0_CS_GPIO_PIN values were defaulting to
something not very usable, because of which e.g. the file system
test app was having to explicitly set the right values in its sample
configuration. Having a proper defaults in the board defconfig means
this isn't needed anymore.
Change-Id: I1399914451c1616588322e25304d40d3dd1151e7
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Test was not completing on CONFIG_DEBUG=y setting, current filter
sets custom stack size for such setting
Jira: ZEP-1203
Change-Id: I3a6ada88bc2e8a1fee757773c4b19b72551926a7
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
We the unified kernel now sizes have gone up and we have some more
testcases that are RAM limited on small memory systems.
Change-Id: I4716a779fac86a420607ba716edd012976d14254
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Commit 4187822d08 removed some filters
at sanitycheck script that were previously preventing foot print test
to run on board quark_d2000_crb.
Added filter excludes such board from min and reg footprint tests.
Change-Id: I2a32e34b1af6d16b3da418cd3113c52b2369eb97
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Making a reference to the common work queue code should not necessarily
drag in the system workqueue, since it is possible to use a workqueue
that is not the system workqueue. This is done by moving the system
workqueue into its own code module.
Moving the system workqueue to its own code module allows removing the
NANO_WORKQUEUE and SYSTEM_WORKQUEUE kconfig options, and compiling the
common workqueue code and system workqueue all the time. They are only
linked in the final image if a reference to them exist, same as the
other kernel modules.
Change-Id: I6f48d2542bda24f4702e7c2e317818dd082b3c11
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This increases number of available L2CAP channels for the test purposes.
This is needed for TC_COS_CFC_BV_05_C test case.
Change-Id: I5df099fb64632e1a0e557852ca55ee45a9cc89ed
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
This fixes configuration file name in testcase.ini file.
Change-Id: I6496f98694415bfc3a76308aa9ee6dfd008e1691
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
This updates README as well as makefile to choose Zephyr BLE firmware
configuration as a default one.
Closes: ZEP-1187
Change-Id: I78dec2a4e2b5bfe634a8b7b8897d4f6ab6b37b44
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
This adds sample configuration file for tester application that
supports controllers with Zephyr-based BLE firmware.
Change-Id: I8b63f93d1395837b8485aba7060b6626be1daab1
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
The README files provided with the samples contain references to NBLE,
which is not a publicly supported solution for Bluetooth. Simply
remove these files. If the need arises to provide application-specific
information in the future we can add back per-application README
files.
Jira: ZEP-1183
Change-Id: I81b3ea5491d50fb16062ccd5a421ddc8fcb7ea42
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove those from Makefiles and testcase.ini, we now support unified kernel
only and sanitycheck script now knows how to deal with this.
Change-Id: I853ebcadfa7b56a4de5737d95f2ba096babb2e13
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Test tests/kernel/test_xip does not fit FLASH region of new platform
cc3200_launchxl that was added by commit 10ea5d0, hence it must be
excluded from such test so daily sanitycheck script completes
successfully.
Jira: ZEP-1201
Change-Id: I01ec2b9af45e34934d91922bd749a83f305746b1
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
The test relies on the workq thread being in the system. It is possible
for the workq to not be in the system even if CONFIG_SYSTEM_WORKQUEUE is
enabled, if nothing makes references to the symbols in the object file,
so we cannot rely on the kconfig option to know if the system workq
thread is in the system or not. So, force it in.
Change-Id: I1ae2613fbd32928b673fc4c74a9dc56502255763
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Port the power management test app to use unified kernel.
Change-Id: I2f10748be5ca7d9792f6e97c35f5f2aabab769e7
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
QMSI 1.3 natively supports restoring the SoC and peripherals
after sleep.
The Zephyr Power Management shim layer is updated
in order to support QMSI functions.
The following functions have been added:
void _sys_soc_set_power_state(enum power_state);
void _sys_soc_power_state_post_ops(void);
In order to fully support deep sleep, the function
_sys_soc_set_power_state now support saving and
restoring CPU context and returns to the application.
_sys_soc_set_power_state function also abstracts
QMSI cpu states and enable the application to choose
between C1/C2 or C2LP states.
The QMSI power states are mapped as follows:
SYS_SOC_POWER_STATE_CPU_LPS -> power_cpu_c2lp
SYS_SOC_POWER_STATE_CPU_LPS_1 -> power_cpu_c2
SYS_SOC_POWER_STATE_CPU_LPS_2 -> power_cpu_c1
SYS_SOC_POWER_STATE_DEEP_SLEEP -> power_soc_deep_sleep
SYS_SOC_POWER_STATE_DEEP_SLEEP_1 -> power_soc_sleep
The following functions have been removed:
void _sys_soc_set_power_policy(uint32_t pm_policy);
int _sys_soc_get_power_policy(void);
FUNC_NORETURN void _sys_soc_put_deep_sleep(void);
void _sys_soc_put_low_power_state(void);
void _sys_soc_deep_sleep_post_ops(void);
Those changes are propagated to the samples.
All calls to QMSI are removed.
Jira: ZEP-1045, ZEP-993, ZEP-1047
Change-Id: I26822727985b63be0a310cc3590a3e71b8e72c8c
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
These testcases can't build on common platforms with 16K or less of
memory.
Change-Id: Iade2aa423f42a1f174a5ebb5d183b362917f503e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Not all platforms enable CONFIG_PRINTK so lets only test if its enabled
Change-Id: I0fc83e21b4be1ff0e8fef94e66793a0b725a3db2
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
QD2000, for example, can't run this.
Change-Id: I86c7ca22e4724844ffc5e64329063baf762470c9
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This test is checking for the wrong results and testing for broken/missing
feature that is actually working.
Jira: ZEP-1124
Change-Id: I7b5f87ac7b47e33e7bbcd4d3967b289f6631cb37
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Microkernel and nanokernel versions of the test now use distinct
sets of source files. This eliminates the dependency on the
MICROKERNEL and NANOKERNEL configuration options, which the
unified kernel doesn't set correctly in all cases.
Change-Id: I59e1d4a73265a433f526d030d2fd04d4b8de1973
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Some HW needs longet timeouts for this TC to complete succesfully.
Change-Id: If6cd4ad93b6e15293f1f8d8e606e159271f0e4d1
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
ztest execute syncronization depends on sem take and give
between TC. Current issues are
*) test execution go to next one before current TC finish
*) one TC failure will block whole testing.
Fix this issue by move k_sem_take from init_testing to
run_test and add k_sem_give in run_test_fail.
Meanwhile, set init sem value range from 0 to 1
Issue: ZEP-1164
Change-Id: I7b2d38501d0965455a71863a4729ee81472a63ec
Signed-off-by: jing wang <jing.j.wang@intel.com>
As we transition to the unified kernel, we need to check on there
being enough memory in said case (nano kernel always had it based on
higher granularity filtering with 'kernel = nano').
Change-Id: Ie21aea2773feb9337d8d34dcf45858e4df879469
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
When running in real HW, testcases take more time to execute than the
default 60s. 200s seems to work for all HW types as of this commit
(FRDM k64f, Arduino Due, Arduino 101 / x86, EMSK 9d).
Change-Id: I663a67161bd7b4c349a483efb8e9cbf14c09421c
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Ability to use Zephyr shell by multiple modules simultaneously, each
module for its own usage.
Old shell implementation enabled the user to call only one module
commands, not all of the modules simultaneously.
Change-Id: I0ef8fa2fd190b7490c44fe91d1016363258302c9
Signed-off-by: Yael Avramovich <yael.avramovich@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Not completely ported to V2 APIs yet, but enough that we pull in
all the kernel.h APIs for the microkernel test, bypassing the legacy
layer.
We pull in a lot more than the legacy test did, so results are not
directly comparable.
Change-Id: I35e74bfd1aa15ee59951f68fb7dd8d811619c3f8
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Nanokernel part of the latency_measure test is a subset of the
microkekernel tests. For unified kernel there is no reason to
have nanokernel test - for unified kernel we have to run whole
the set of tests.
Change-Id: Ief176fd9d25e7355e3d3697c3bbc1e953b16655c
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>