To meet CPU time usage restricts inside radio ISR on nRF51
SoCs, use ccflags -Ofast when using fast encryption setup
implementation in the controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Default to n the support for Data Length Update and
PHY update procedures on nRF51 SoCs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixed an assert when peer responded with unknown rsp to
slave feature request when an existing another control
procedure was in progress.
This assert happened with a BT v4.0 peer implementation that
was performing a channel map update and local controller
initiated a slave feature request, receiving an unknown
response.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Without this fix there is an issue when doing PB-ADV provisioning
with PTS. We keep retransmitting Public Key which is ACKed by PTS and
this leads to transaction timeout as PTS does not send confirm probably
because it keep receiving PK from us.
This patch also makes sure that transaction id is between 0x80 - 0xFF
Signed-off-by: Łukasz Rymanowski <lukasz.rymanowski@codecoup.pl>
Needed for following PTS test cases:
MESH/NODE/PROV/UPD/BV-10-C
MESH/NODE/PROV/BI-02-C
Signed-off-by: Łukasz Rymanowski <lukasz.rymanowski@codecoup.pl>
Fix the control and data packet management implementation
discovered during conformance testing.
This fixes:
TP/SEC/MAS/BV-12 [Master Start Encryption: Overlapping
Procedure]
TP/SEC/MAS/BV-13 [Master Start Encryption: Overlapping
Procedure with LL_SLAVE_FEATURES_REQ]
conformance tests in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Privacy on nRF51 is not passing the conformance and qualification tests
due to the time it takes to execute the privacy code while in ISR. Until
we come up with a way of optimizing and/or deferring the work, do not
allow privacy on nRF51 targets.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the macros generated during the build and located in version.h to
fill in the version information in the Read Version Information VS
command. Additionally reply with the correct hardware identifiers when
running on Nordic hardware.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Seems due to incorrect rebase in commit 07270e52ba
("Bluetooth: controller: Coding style and refactoring"),
commit 95d55a2bfc ("Bluetooth: controller: Do not skip
one-shot tickers with slot"), and
commit 4ba2bb0d1c ("Bluetooth: controller: Be fair when
pre-empting a ticker"), a pointless expression was
introduced, fixed it.
Coverity-CID: 171563
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This reverts commit 817245c564.
In certain cases the peer seems to discard the FIN packet we are
sending, which means that the TCP stream is not closed properly.
This needs more work so revert this for time being.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code was setting the wrong bit of the Static OOB Type when a
static value has been provided.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When new socket context is created on accepting connection to a
listening socket, its recv_q FIFO should be initialized. Without
initialization, this worked by a chance when FIFO structure was
simple, but recent change to add dlist to it (which now needs
proper initialization) exposed this issue.
Jira: ZEP-2576
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If the query name is already in numeric format, there is no
need to send the query string to DNS server as we can just
convert it ourselves.
Jira: ZEP-2562
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit removes IP address parsing from DNS init and
replaces it by call to net_ipaddr_parse().
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_ipaddr_parse() will take a string with optional port
number and convert its information into struct sockaddr.
The format of the IP string can be:
192.0.2.1:80
192.0.2.42
[2001:db8::1]:8080
[2001:db8::2]
2001:db::42
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fixes an assert during connection establishment when the
initiator overflows the initiator window in time while
sending the CONNECT_IND PDU. The actual window is one low
frequency tick less, hence corrected the check that permits
the transmission of CONNECT_IND PDU inside the initiator
window.
Symptom was, stopping of the scanner's ticker succeeds on
connection establishment, but next interval prepare was
already run when continuous scanning was used, breaking the
design, hence there was an assert.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If network context is closed, send FIN by placing it to the end
of send queue instead of sending it immediately. This way all
pending data is sent before the connection is closed.
Jira: ZEP-1853
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Implement the Zephyr Read Key Hierarchy Roots command, returning the IR
and ER present in nRF5x ICs when compiling for those.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the first Vendor-Specific Command of the Zephyr specification
other than the 3 mandatory ones already present in the codebase, along
with a Kconfig option to enable and disable the presence of the VS
commands.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
TLS and DTLS are not related to each other so allow DTLS to be
enabled even if TLS is disabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The "net app" command was accessing NULL pointer if TLS and UDP were
enabled but DTLS was not.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Earlier we modified the original pkt chain when creating IPv6
fragments. This is not a proper way as the original chain might
still be used in TCP when re-sending a message. So when fragmenting
the packet, clone it first and leave original packet intact. This
occupies litle more memory but is now safe.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is very unlikely to happen but the device will access null
pointer if we do not properly check the return value of header
check function.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When trying to figure out where ICMP / TCP / UDP header is located
in net_buf, print more information about what we were doing if the
header cannot fit the first fragment. This is much needed infomation
in debugging weird issues.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Using memcpy() to copy net_pkt is not safe because there are
pointers inside. So use the new net_pkt_clone() to do that.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is needed when one wants to copy the whole fragment chain
and its head pointer net_pkt.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IP header was stripped by _net_app_ssl_mux() when it received
IP packet. This is fine but if the application expects the get
the IP header, then there is a problem. Fix this by saving IP
header to ssl_context and then putting it back in front of the
packet when the data is passed to application.
Note that this IP header is not used by net_app when the packet
is sent because TLS/DTLS creates a tunnel for transferring packets
and user can only sent packets via this tunnel.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
k_delayed_work_cancel now only fail if it hasn't been submitted which
means it is not in use anyway so it safe to reset its data regardless
of its return.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This is necessary in order for k_queue_get to work properly since that
is used with buffer pools which might be used by multiple threads asking
for buffers.
Jira: ZEP-2553
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Refactor the Connection Parameter Request Procedure to be
separate from and not overlap the variables of the
Connection Update Procedure.
Also, added missing implementations to pass all Connection
Parameter Request Procedure related Conformance Tests.
Jira: ZEP-1918
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Implement the LE Read Channel Map HCI command, along with making the
reading of the multi-byte channel map value from the connection pointer
thread-safe in case the ISR triggers while we are reading the value.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Although the current BLE controller only supports a single TX power (0
dBm), the qualification tests require the 2 Read TX Power to be
present and supported in the controller, so implement them while
returning always 0 dBm.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When the CONFIG_BT_CTLR_CONN_RSSI option is set, the connection RSSI is
available in the controller, and can be reported to the Host via the
Read RSSI command. Implement the command, which is required for
qualification.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The original commit 8ebaf29927 ("net: http: dont timeout
on HTTP requests w/o body") was intended to handle a case
where an HTTP response had been retrieved from the server but
the HTTP parser couldn't meet the criteria for calling
"on_message_complete". For example, a POST to a REST API
where the server doesn't return anything but an HTTP
status code.
It was a really bad idea to check a semaphore count. There
is a lot of kernel logic built into semaphores and how the
count is adjusted. The assumption that the value is 0
after the k_sem_give() is incorrect. It's STILL 0 if
something is pending with a k_sem_take(). By the time
k_sem_give() is done executing the other thread has now
been kicked and the count is back to 0.
This caused the original check to always pass and in turn
breakage was noticed in the http_client sample.
Let's do this the right way by setting a flag when
on_message_complete is called and if that flag is not set
by the time we reach recv_cb, let's give back the semaphore
to avoid a timeout.
Jira: ZEP-2561
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The HTTP header field pointers are saved for each HTTP request.
But the counter that saves the pointers was never reset to initial
value when the connection was dropped. This meant that the header
field values were only proper for first HTTP request.
Jira: ZEP-2463
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The server needs global enable/disable status instead of only being
able to enable or disable just the TLS server part.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we have specified AF_UNSPEC when initializing application
server local address, then we try to bind to both IPv4 and IPv6
addresses. The old code did not honor the port number in this
case but used some random value for port.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user has specified a specific local address, then honor that
and do not try to bind IPv4 context if only IPv6 is defined,
and vice versa for IPv6.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Zeroing-out all bytes from a connection structure when it's
unregistered ensures all state from a previous connection is gone and
can't be mistakenly reused.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
If either a remote or a local address were supplied to the
net_conn_register() function, the IP stack would proceed to copy
sizeof(struct sockaddr) bytes from the respective remote_addr
or local_addr pointers, regardless of the actual size of the storage
these pointers point to.
Use the proper size depending on the socket address family.
Coverity-ID: 173630
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
There are 2 possible interpretations regarding the address to return in
response to the Read Peer RPA HCI Command:
1) The RPA that the local controller generates to be used in certain
packets it sends
2) The RPA generated and used by the peer device in its packets
We used to return 1) but our interpretation turned out to be incorrect
when reading the HCI test specification, so this commit switches to
returning 2).
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
If CONFIG_NET_DEBUG_APP was defined, but neither NET_APP_SERVER nor
NET_APP_CLIENT, build failed due to net_app_cb() haven't beeen
defined. So, define it to empty in this case.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
In the ll_rl_pdu_adv_update() function, the check to verify if we are
dealing with an item from the resolving list or else with a simple
standard non-privacy enabled device was left over from the previous
iteration, which used negative values. Replace that check with the
proper current one, using the size of the rl array as an indicator of
whether the index is valid.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Due to varying remainder value, first interval will need to
consider the remainder value used in microsecond timing from
the start of the initiator window.
Also the tx chain delay and ready delay must be substract
after the window offset is calculated.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The Read Remote Version Information command is supported on the BLE
controller, enable the bit in Read Local Supported Commands to reflect
this.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Setting just IPv4 address as was allowed before isn't enough for
real-world usage (e.g. accessing DNS and outside servers in general).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Per LwM2M spec (7.3.2.4 Operation on Object):
"If the payload (New Value) conveys an Object Instance ID in conflict
with one already present in the LwM2M Client, the complete request
MUST be rejected and a "Bad Request" error code MUST be sent back."
Let's do that.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Per LwM2M specification 7.3.2.4, "Optional Resources MAY be conveyed
in the "New Value" parameter as well; the LwM2M Client MAY ignore the
optional resources it doesn't support."
Update TLV/JSON writer to ignore error when object fields are not
found (treated as optional resource). This will allow the resources
supported being written.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: re-worked patch post addition of CREATE
operation.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Prior to this patch, a CREATE operation was handled as a WRITE operation
after the object instance was created. This becomes problematic when
handling of optional resources differs between these 2 operations.
Let's introduce an actual CREATE operation and use it later to create
these differences.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
We are returning EINVAL from content format write ops when an object
field definition is not found (an optional field which is not
implemented). Instead, return ENOENT which lets the LwM2M engine
know to send ZOAP_RESPONSE_CODE_NOT_FOUND to the LwM2M server at the
end of handle_request().
NOTE: This behavior is not correct when we call the writer right after
a CREATE operation where the data is assigned to resources for the
first time. This case will be handled in a follow-up patch once we're
able to distinguish between a WRITE and a CREATE in the write op
handler.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
POSIX requires struct sockaddr's field to be named "sa_family"
(not just "family"):
http://pubs.opengroup.org/onlinepubs/009696699/basedefs/sys/socket.h.html
This change allows to port POSIX apps easier (including writing
portable apps using BSD Sockets compatible API).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Fix controller assert due to a bug introduced in commit
07270e52ba ("Bluetooth: controller: Coding style and
refactoring").
This reverts implementation to original way it was and the
calculation of the ticker expiry will now not overflow the
range of the RTC peripheral, which is a 24 bit counter.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
net_pkt_get_reserve_data ignores the timeout parameter when in isr,
using K_NO_WAIT instead, which can lead to invalid fragment.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Per LwM2M specification 5.3.1 Register, report "ct=11543" when JSON is
supported. Also, report the resource type as rt="oma.lwm2m" when "ct="
presents.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Per LwM2M specification 5.3.1 Register. When object instances are
available, object ID can be ignored in registration message
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
According to LwM2M specification 5.2.7.3 Bootstrap DISOCVER,
security object is only reported to the bootstrap server.
Correct the behavior to (1) report server object to the server
(2) do not report security object at registration time
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Fix checks for BT_HCI_RAW and move default range after the other range
options, required by Kconfig to avoid overwriting other options.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
This is how it's called in the main docs, so use this same phrase in
Kconfig and samples too.
Also, added some articles to docs.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The RSSI value is an 8-bit signed integer. Since the Link Layer works
only with positive unsigned integers, translate into a negative number
at the HCI layer.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This option enables full debugging output for memory allocations.
As that can produce lot of output and slow down the device under test,
it is disabled by default.
The previous CONFIG_NET_DEBUG_NET_PKT will collect information about
memory allocations but will not print any output. Use "net mem" or
"net allocs" commands in net-shell to see the memory allocation status.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Because the name of the memory pool can be quite long, print
it last so that the columns get aligned nicely.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we are not in ESTABLISHED state, then there is no need to
try to resend any pending data packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the expire send timer expires, then it sends the packet.
If that happens, then we must not try to send the same packet
again if we receive ACK etc. which can cause re-sends to happen.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the packet sending is slow then we must NOT increment the ref
count when re-sending it. This is unlikely but can happen if there
are lot of debug prints etc. extra activities that prevent the driver
to actually send the packet fast enough.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that the sent flag is only set after we have really
sent the packet and the driver has verified that.
If the net_pkt_set_sent() is called while still in tcp.c, then
depending on how fast the device is, it might happen that the
retry timer expires before the packet is actually sent. This was
seen in frdm-k64f with ethernet and various debug prints activated.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is a backlog entry when TCP context is released, then
cancel the ACK timer if one exists.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that a network packet is sent after calling
http_response_send_data(). Othwerwise the packets might be
piling up and not sent in timely manner.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some older C libraries do not have errno for EPFNOSUPPORT.
Fixes issues with newlib in some versions of Xtensa XCC compiler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The initial function prototype did not have 'inline' in it,
resulting in a compiler warning with XCC.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
It's never a good idea to redefine functions as macros if intended
to be unused in some configuration
- "statement with no effect" warnings
- "unused argument" warnings
- No type checking done if the macros are used
These have been redefined as empty inline functions.
Fixes compiler warnings with XCC.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The second 'const' is misguided, indicating that the returns pointer
value itself cannot be changed, but since pointers are passed by value
anyway this is not useful and was generating warnings with XCC.
The leading 'const' indicates that the memory pointed to is constant,
which is all we needed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Inline functions declared in header files need to be declared
static. Fixes a compiler warning with XCC compiler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Older value of 256 was introduced in 1.7 times. Testing on
BOARD=96b_carbon with 2 weeks old codebase however showed that TX
thread stack however can grow to 324 bytes. Finally, with the
latest master, following stacks are reported on BLE disconnect
(with CONFIG_INIT_STACKS enabled):
rx stack (real size 1024): unused 452 usage 572 / 1024 (55 %)
tx stack (real size 384): unused 16 usage 368 / 384 (95 %)
Two outcomes:
1. TX stack needs increase.
2. Over time, the stack usage grows, plus variations in SPI
drivers should also be taken into account.
So, increase the stack size to 416 bytes, to leave some headroom
beyond the immediate values seen on 96b_carbon.
Jira: ZEP-2510
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Currently, the HTTP_NETWORK_TIMEOUT setting is hard-coded as 20 seconds.
Not every application may want to wait that long, so let's change this
to a CONFIG option: CONFIG_HTTP_CLIENT_NETWORK_TIMEOUT
NOTE: This also removes HTTP_NETWORK_TIMEOUT from the public http.h
include file. It was not being used externally to HTTP client sources.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Add a sample application that allows a Zephyr-based Bluetooth
controller to interface with an HCI driver via SPI. This sample
implements the same BT SPI protocol already as Zephyr's HCI SPI
driver.
Currently, the sample only supports the legacy SPI API.
Provide a single configuration file, avoiding board-specific
files. Some board-specific configuration information must be provided
via other means:
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_DEV_NAME
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_IRQ_DEV_NAME
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_IRQ_PIN
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Since Extended Scanner Filter Policies is an independent feature from
Controller-based Privacy, split it out so it can be built independently
and included without it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
A TCP FIN message is passed on to user apps as a tcp_received_callback
with a NULL pkt parameter. This means the connection is closing and
the app should do whatever cleanup it needs as there will be no further
callbacks for the current TCP connection.
Currently, if a HTTP client request doesn't receive a "body" which
the HTTP parser can use to trigger on_message_complete, then the request
will end up timing out and most apps will think an error has occurred.
Instead, let's handle the TCP FIN message and return the waiting
semaphore, leaving the app to deal with whatever has been set in the
current HTTP context response data (IE: http_status).
This fixes using HTTP client to send POST data to servers which
only respond with HTTP_OK status and no body.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Unless offset was specified, it should default to 0, whereas
previously, value from the last command was used.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
"Network Application Support" itself is renamed from "Network
Applications" and also includes net_app API.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Whenever privacy is enabled, we support the Extended Scan Filter
Policies functionality, and therefore we must show it in the bitfield of
LE supported features for the controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Rename the BT_CONTROLLER prefix used in all of the Kconfig variables
related to the Bluetooth controller to BT_CTLR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Avoiding segmentation in the GATT-based Mesh Proxy protocol requires
having an RX buffer length of at least 77. We could round it up to 80
since there's otherwise wasted space, however there's also
BT_HCI_RESERVE to consider, so to avoid pushing over the 4-byte
boundary for certain HCI drivers just leave the size at 77.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is needed in order to get information which function is
doing the ref. With inline function this was not possible.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of printing [net/net_pkt], print [net/pkt] if debug log
is enabled for network packet allocator. The double net in earlier
print is redundant information.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of always have CONFIG_NET_IPV6_MAX_NEIGHBORS parents,
use CONFIG_NET_RPL_MAX_PARENTS when creating the parent table.
Default value for max parents is the max neighbors so no
functionality changes are introduced here.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of always having CONFIG_NET_IPV6_MAX_NEIGHBORS number
of items in neighbor pool, store the neighbor count in the pool
and use that value when traversing the neighbor table.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Allow user to define what kind of network the RPL should serve.
Currently options will be either ANY or IEEE802154. If there
is only one network interface in the system, then ANY will take
the default network interface and use that. If there are multiple
network interfaces, then one should not use ANY as the default
network interface might not be the expected one.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print network interface where the DIO, DIS or DAO was sent. This is
useful if we have multiple network interfaces in the system.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When printing network interface specific data, print also
the type of the network interface (ethernet, bluetooth etc).
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the user has not specified CONFIG_NET_APP_MY_IPV4_ADDR or
CONFIG_NET_APP_MY_IPV6_ADDR, the value is set to "" in this case.
This will be converted to ANY IP address which is not useful
to be set to the network interface. So check this and just
continue the init in this case without setting the IP address.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The documentation says that the API will automatically append the
net_buf fragment to the end of network packet fragment chain.
This was not the case and current only user for this API in
echo-server sample appended the fragment itself. The fix is to
automatically append the fragment to the end of fragment chain.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
1. According to the specification 5.3.1, it's a MUST to specify
(1) content format: app link format (2) supported lwm2m version.
Also, we should use text/plain instead of LWM2M's (obsolete).
2. Use LWM2M_FORMAT_OMA_TLV as default accept format when accept option
is not given from the caller for TLV is a MUST have in LwM2M spec and
it can deals w/ multiple resources read
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Save in observe_node_data so that later on we can select the correct
content format requested by the caller at the first time
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Function do_write_op_tlv() uses in->inbuf and in->insize as a looping
condition to iterate through items in TLV payload and call
do_write_op_tlv_item() to update the value.
However, do_write_op_tlv_item() will override the value before calling
for fitting the usage of lwm2m_write_handler() function without restore
them. (lwm2m_write_handler() is also called by plain text/json writer
and is expecting in->inbuf is the start of buffer and in->insize as the
length of the buffer)
This will result in errors in do_write_op_tlv().
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
RFC-7230 "HTTP/1.1 Message Syntax and Routing" Section 5.4
describes the "Host" header formatting. If Zephyr user
specifies a host string as a part of the HTTP client request
structure, we end up sending an incorrect HTTP header due
to a missing "Host :" text.
Fix this by prepending "Host: " to the header data before
the user supplied host string.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
openocd object was put in a library causing it to be stripped. We want
those symbols in the final ELF to allow debugging with openocd, building
those as objects like the rest of the kernel keeps the symbols in the
kernel.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
sprint_token is only used by SYS_LOG_DBG, so only build it when
CONFIG_SYS_LOG_LWM2M_LEVEL > 3.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Separate response can happen when handling block transfer for firmware
updates, and to avoid duplicating the lwm2m_udp_receive function, create
and additional flag to allow handling CoAP separate response messages.
This is required to avoid removing the reply callback, since a new
message (with a valid token) will be received later from the server.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Simplifly net_context_sendto calls and also allows to easily debug every
send/receive lwm2m call.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Implement the 4.2 event LE Directed Advertising Report, used for
scanners in a privacy-enabled controller to report directed advertising
events whose TargetA cannot be resolved by the local controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add implementation to support PHY update procedure with
packet transmit time restrictions.
This fixes:
TP/CON/SLA/BV-49-C [Initiating PHY Update Procedure Packet
Time Restrictions]
TP/CON/SLA/BV-50-C [Responding to PHY Update Procedure
Packet Time Restrictions]
TP/CON/SLA/BV-52-C [Initiating PHY Update Procedure Packet
Time Restrictions, No Change]
TP/CON/SLA/BV-53-C [Responding to PHY Update Procedure
Packet Time Restrictions, No Change]
TP/CON/MAS/BV-49-C [Initiating PHY Update Procedure Packet
Time Restrictions]
TP/CON/MAS/BV-50-C [Responding to PHY Update Procedure
Packet Time Restrictions]
conformance tests in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The CONFIG_BT_WAIT_NOP define is used only by
zephyr/subsys/bluetooth/host/hci_core.c.
It is also the only config in drivers/bluetooth that is in use when
BT_CONTROLLER is enabled. Moving it into the bluetooth subsystem
allows us to restructure the drivers/kconfig code such that the entire
Bluetooth driver menu option is omitted when the BT_CONTROLLER is
enabled.
Moving it will also mean that all configs in drivers/bluetooth will
now be related to configuring the source code in drivers/bluetooth.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
If the device has multiple network interface, then we must not
blindly use the default one but get the IEEE 802.15.4 network
interface when setting radio parameters in the shell.
Jira: ZEP-2432
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print route information by groupping them for each network
interface like this:
IPv6 routes for interface 0xa8007140
====================================
IPv6 prefix : 2001:db8::212:4b00:0:3/128
neighbor : 0xa80065e0
link addr : 00:12:4B:00:00:00:00:03
IPv6 prefix : 2001:db8::212:4b00:0:1/128
neighbor : 0xa8006660
link addr : 00:12:4B:00:00:00:00:01
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add "net rpl" command to net-shell which will return both static
RPL configuration from Kconfig, and dynamic run time configuration
of the nodes and parents.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create net_rpl_foreach_parent() function that will traverse
through all the parents and return their information via callback.
This is needed by net-shell in later commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If debug level was low but debugging was activated, then some
of the debug variables were left unused.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_rpl_repair_root() and net_rpl_set_root_with_version()
functions were static which prevented global repair when using
an instance id. Making those functions global allows RPL network
repairing from shell for example.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit b14586c3ca ("net: rpl: RPL route entry was fetched
too late") dropped the DAO packet too early which prevents the
RPL root node functionality. Rework the earlier commit so that
Coverity issues are fixed but the RPL DAO message is also properly
handled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
IPSO Smart Objects are a set of template objects based on the LwM2M
object framework which are designed to represent standard hardware
such as temperature and humidity sensors or light controls.
Let's add a place for these objects to live as well as an initial
temperature sensor object.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Origin: SICS-IoT / Contiki OS
URL: https://github.com/sics-iot/lwm2m-contiki/tree/lwm2m-standalone-dtls
commit: d07b0bcd77ec7e8b93787669507f3d86cfbea64a
Purpose: Introduction of LwM2M client library.
Maintained-by: Zephyr
Lightweight Machine-to-Machine (LwM2M) is a protocol stack extension
of the Constrained Application Protocol (CoAP) which uses UDP
transmission packets.
This library was based on source worked on by Joakim Eriksson,
Niclas Finne and Joel Hoglund which was adopted by Contiki and then
later revamped to work as a stand-alone library.
A VERY high level summary of the changes made:
- [ALL] sources were re-formatted to Zephyr coding standards
- [engine] The engine portion was re-written due to the heavy reliance
on ER-CoAP APIs which are not compatible to the Zephyr CoAP APIs as
well as other Zephyr specific needs.
- [engine] All LWM2M/IPSO object data is now abstracted into resource
data which stores information like the data type, length, callbacks
to help with read/write. The engine modifies this data directly (or
makes callbacks) instead of all of the logic for this living in each
object's code. (This wasn't scaling well as I was implementing
changes).
- [engine] Related to the above change, I also added a generic set of
getter/setter functions that user applications can call to change
the object data instead of having to add getter/setting methods in
each object.
- [engine] The original sources shared the engine's context structure
quite extensively causing a problem with portability. I broke up the
context into it's individual parts: LWM2M path data, input data and
output data and pass only the needed data into each set of APIs.
- [content format read/writer] sources were re-organized into single
.c/h files per content formatter.
- [content format read/writer] sources were re-written where necessary
to remove the sharing of the lwm2m engine's context and instead only
requires the path and input or output data specific to it's
function.
- [LwM2M objects] re-written using the new engine's abstractions
Signed-off-by: Michael Scott <michael.scott@linaro.org>
In the 08 Feb 2017 V1.0 LwM2M specification page 80 mentions: in
response to a "Notify" operation for which it is not interested in
any more, the LwM2M Server can send a "Reset Message".
Leshan server sends this CoAP RST response and it does not contain
the originating message token (which is also how the packet flow looks
on page 81 of the LwM2M spec). Using the current ZoAP sources, the
client has no way of matching back to observation which needs to be
cancelled.
Let's add a match for message ID of a reply where there is no token
to handle this case.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
[ricardo.salveti@linaro.org: Handle both piggybackend and separate
response (id doesn't need to match, only token).]
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
There are two kinds of HCI implementations. Bluetooth drivers in
drivers/bluetooth that implement HCI by using a wired serial
transport layer to talk to an external controller chip. And a
bluetooth controller in subsys/bluetooth/controller that directly
talks to an internal on-chip controller node.
Currently, when the the subsys/bluetooth/controller is used there
still exists exposed to the user a bluetooth driver configuration
menu, even though no external bluetooth driver is in use. This is due
to a dependency on certain configs in driver/bluetooth that are needed
even though no external controller is used.
This patch moves one of these configs, BLUETOOTH_HCI_RESERVE, from
drivers/bluetooth/hci/Kconfig to subsys/bluetooth/host/Kconfig such
that eventually we can omit the entire Bluetooth driver menu option.
This re-organization does not change when the config can be enabled.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Fix incorrect return data type, which causes controller to
hang generating random numbers.
Fixes bug introduced in commit d90095b556 ("Bluetooth:
controller: Use random numbers in adv and enc setup")
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The specification requires the scanner to verify that the AdvA present
in a scan response matches the AdvA that was sent in the original scan
request.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added implementation to get random numbers in ISR. And fixed
implementation to use random numbers in advertisement random
delay and encryption setup procedure.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
For an accepted socket, we should set our receive callback and start
to queue packets ASAP (in the accept callback itself). Otherwise,
(if done in accept() call like before) we may miss to queue some
packets.
This issue wasn't exposed with slow SLIP and with emulated QEMU, but
easily exposed with Ethernet on a real hardware.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
We need to define __LINUX_ERRNO_EXTENSIONS__ if newlib is being
used otherwise there is a compile error about ESHUTDOWN errno
value missing.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
- Fix typo'd "&&" when checking bit value
- Don't use NET_EVENT_IPV6_ADDR_ADD for checking mask value
due to combination of bits: _NET_EVENT_IPV6_BASE |
NET_EVENT_IPV6_CMD_ADDR_ADD
Instead use NET_EVENT_IPV6_CMD_ADDR_ADD so the check works
when NET_EVENT_IPV6_ROUTER_ADD is enabled.
Tested fix with echo_server on x86 qemu where it was previously
broken.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The existing check for the TargetA address in directed advertising
events was incorrect. In fact the specification states:
"An initiator that has been instructed by the Host to use
Resolvable Private Addresses shall not respond to directed connectable
advertising events that contain Public or Static addresses for the
target’s address (TargetA field)."
Hence, reject TargetA values that have not been successfully resolved
when the controller is generating its own RPAs.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Unlikely to happen but make sure parent neighbor exists when
probing it.
Coverity-CID: 173635
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is no parent found with a specific dag, then we have
to check this in order not to access NULL pointer.
Coverity-CID: 173637
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the parent is not found when adding DAG, then just return.
We must check the parent pointer as it can be NULL.
Coverity-CID: 173638
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
No need to complex overflow checks that are error prone.
Coverity complained that the original diff check was always
false.
Coverity-CID: 173639
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There was dead code when handling IPv6 Hop-by-hop option.
The extra option value check can be removed as it is useless.
Coverity-CID: 173642
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Coverity complains about non-checked return values here. This is false
positive as the return values do not need checking in this special
case because we are closing the socket.
Coverity-CID: 173646
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Coverity complains about reversed src and dst fields when sending
DAO ack back to originator. This is false positive.
Coverity-CID: 173650
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Check the return value of k_poll() as instructed by Coverity.
If debugging is enabled we print error if this happens, otherwise
this error is ignored. In our case the return value should always
be 0.
Coverity-CID: 173652
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It is be possible that the local address was not properly
resolved in which case the local_addr variable could be NULL.
This will cause NULL pointer access if the variable is used.
Coverity-CID: 173656
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The RPL route entry variable "extra" was resolved inside an
if-statement and the code was always returning from it.
This meant the the later code dealing with "extra" was never
executed. Fixed by moving the resolving of "extra" a bit
earlier so that the "extra" variable has always a proper value.
Coverity-CID: 173659
Coverity-CID: 173654
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The TX send function will return status < 0 if there is an error
when sending. This status value was incorrectly checked.
Coverity-CID: 173660
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix compiler warnings resulting from passing C string literals to
functions expecting an unsigned char pointer.
Jira: 2443
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To be able to get a hit on the AAR whenever a Scan Response is received,
enable it in the state transition.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add missing checks for the logic that discriminates between whitelisting
and non-whitelisting filtering, so that we do not fall into an
unsuspected false positive.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As we buffer incoming packets in receive callbacks, we must decrease
receive window to avoid situation that incoming stream for one socket
uses up all buffers in the system and causes deadlock. Once user app
consumes queued data using recv() call, we increase window again.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This fixes the existing situation that "if application buffers data,
it's the problem of application". It's actually the problem of the
stack, as it doesn't allow application to control receive window,
and without this control, any buffer will overflow, peer packets
will be dropped, peer won't receive acks for them, and will employ
exponential backoff, the connection will crawl to a halt.
This patch adds net_context_tcp_recved() function which an
application must explicitly call when it *processes* data, to
advance receive window.
Jira: ZEP-1999
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This enables IPSP node role which requires IPSS GATT service to be
registered.
Jira: ZEP-2451
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds NET_REQUEST_BT_ADVERTISE which can be used to advertise
IPSS service so the remote devices can connect to it.
Jira: ZEP-2451
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some network interfaces such as bluetooth 6lowpan can start without
an assigned IP address and then later once the connection is up a
router advertisement broadcast will assign the IP address.
The net_app framework will timeout out during network init if a value
cannot be parsed from CONFIG_NET_APP_MY_IPV6_ADDR. Let's adjust
the framework to handle a missing value there and fill it in later
when the IPv6 address is added to the interface.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Rework the ctrl_lrpa_get() function so that it doesn't require an
assignment to be present inside the if statement, yielding smaller and
safer code.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Advertising reports generated by a scanner require the controller to
look up the resolving list to supply the host with an ID address instead
of the RPA that has been sent over the air.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the actual scanner address to copy the generated RPA into, instead
of mistakenly copying it into the advertiser's address.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Whenever trying to generate a local RPA to send a scan request or a conn
ind, verify that it can be generated (i.e. no NULL IRK provided by the
Host) and fall back to using the public/random address if required.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the hardware expects big-endian IRKs but the common generation
function expects it in little-endian, copy and reverse the peer IRK
before generating RPAs.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
ReST defines interpreted text roles where text enclosed by single quotes
can be "intrepreted", for example :ref:`some name` becomes a link to
a label anywhere in the doc set named "some name", :c:func:`funcname()`
becomes a link to the API documentation for "funcname", and
:option:`CONFIG_NAME` becomes a link to, in our case, the documentation
for the generated Kconfig option.
This patch fixes uses of `some name` (without a role) by either adding
an explicit role, or changing to ``some name``, which indicates inline
code block formatting (most likely what was intended).
This is a precursor to changing the default behavior of interpreted
text to treat `some name` as :any:`some name` (as configured in
doc/conf.py), which would attempt to create a link to any available
definition of "some name".
We may not change this default role behavior, but it becomes an option
after the fixes in this patch. In any case, this patch fixes incorrect
uses of single-quoted text (possibly introduced because GitHub's
markdown language uses single-quoted text for inline code formatting).
Jira: ZEP-2414
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Implement the LE Enhanced Connection Complete HCI event, but include it
only when controller-based privacy is enabled, since it is only relevant
with it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since a connection attempt can fail and will still generate an LE
Connection Complete event, check the status from the LL control module
before incrementing the HCI connection count used for flow control.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The Test ID was incorrectly being added as 4 bytes (size of a pointer)
instead of the intended 1 byte.
This fixes Coverity CID 173643.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current 960 is at least too small under qemu_x86:
ecc stack (real size 1024): unused 36 usage 988 / 1024 (96 %)
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The nRF5 AAR requires the packet pointer to be placed exactly 3 bytes
before the beginning of the address. Since we don't use the S1 extra
length byte, substract one from the address of the radio packet pointer.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The currently supported hardware in the LL requires big-endian IRK
values to properly function. Reverse the order of the IRK bytes coming
from HCI to address this issue.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The nRF5's AAR was being improperly configured, leading to a NULL
scratch pointer which made it not function at all.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Historically, stacks were just character buffers and could be treated
as such if the user wanted to look inside the stack data, and also
declared as an array of the desired stack size.
This is no longer the case. Certain architectures will create a memory
region much larger to account for MPU/MMU guard pages. Unfortunately,
the kernel interfaces treat both the declared stack, and the valid
stack buffer within it as the same char * data type, even though these
absolutely cannot be used interchangeably.
We introduce an opaque k_thread_stack_t which gets instantiated by
K_THREAD_STACK_DECLARE(), this is no longer treated by the compiler
as a character pointer, even though it really is.
To access the real stack buffer within, the result of
K_THREAD_STACK_BUFFER() can be used, which will return a char * type.
This should catch a bunch of programming mistakes at build time:
- Declaring a character array outside of K_THREAD_STACK_DECLARE() and
passing it to K_THREAD_CREATE
- Directly examining the stack created by K_THREAD_STACK_DECLARE()
which is not actually the memory desired and may trigger a CPU
exception
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
A new net-shell command "net app" will print information about
network app users in the system.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add API that allows net-shell to get net_app context information
that can be used to debug net_app connections.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In order to make sure that the ISR never gets an incomplete or partial
local RPA, use pointers to share the local RPA between thread mode and
ISRs. Pointer updates are guaranteed to be atomic at least on ARM
Cortex-M.
Additionally add support for using local RPAs when initiating a
connection or sending a scan request.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the hardware is only able to resolve the first address in the
packet, use the existing functionality to resolve a potential TargetA
RPA in software to verify if it matches the local device.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit introduces controller-based privacy for both the scanner and
the initiator roles. All the features in the specification are
implemented except:
* RPA resolution for directed advertising (TargetA address)
* RPA generation for scan requests and conn ind packets
Follow-up patches will cover the 2 items of functionality still missing
from the basic implementation. Hosts not using controller-based privacy
should not be affected by this change.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
If peer has previously configure to received service changes indications
any changes to the database during the time it has been disconnected
shall be indicated once it reconnects:
[bt] [DBG] sc_process: (0x004065b4) start 0x000a end 0x0014
[bt] [DBG] sc_save: (0x004065b4) peer b8:8a:60:d8:17:d7 (public)
start 0x000a end 0x0014
[bt] [DBG] bt_gatt_connected: (0x00405240) conn 0x00405aa0
[bt] [DBG] gatt_ccc_changed: (0x00405240) ccc 0x00400b30 value 0x0002
[bt] [DBG] sc_ccc_cfg_changed: (0x00405240) value 0x0002
[bt] [DBG] sc_restore: (0x00405240) peer b8:8a:60:d8:17:d7 (public)
start 0x000a end 0x0014
[bt] [DBG] sc_process: (0x004065b4) start 0x000a end 0x0014
[bt] [DBG] gatt_indicate: (0x004065b4) conn 0x00405aa0 handle 0x0008
[bt] [DBG] sc_indicate_rsp: (0x00405240) err 0x00
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
bt_gatt_indicate return 0 in case of success, not true, so
SC_INDICATE_PENDING was flag was not set when it should.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Control and Data packet Tx queue management updated to be
optimal and defer control packet responses when Tx is paused
during encryption setup.
This fixes:
TP/SEC/MAS/BV-12 [Master Start Encryption: Overlapping
Procedure]
TP/SEC/MAS/BV-13 [Master Start Encryption: Overlapping
Procedure with LL_SLAVE_FEATURES_REQ]
conformance tests in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix handling of different procedure collision when receiving
a PHY update request and handling of reject extended
indication.
This fixes:
TP/CON/MAS/BV-47-C [Handling Protocol Collision – Different
Procedure – Channel Map],
TP/CON/SLA/BV-46-C [Handling Protocol Collision – Different
Procedure – Channel Map] and
TP/CON/SLA/BV-48-C [Handling Protocol Collision – Different
Procedure – Connection Update]
conformance test in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix missing PHY update event generation on same procedure
collision,
This fixes TP/CON/SLA/BV-44-C [Handling Protocol Collision –
Same Procedure] conformance test in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix PHY update procedure intiation to use correct No Change
value in MtoS and StoM when there is no change to respective
PHYs. Also, added missing HCI event generation under this
case.
This fixes TP/CON/MAS/BV-41-C [Initiating PHY Update
Procedure] conformance test in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
As ticker can only drift in 32kHz units, the slave Rx
window should consider a +/- one 32kHz unit in addition to
+/- 16us jitter of the master. Hence, for the current
implementation the slave Rx window jitter is +/- 48us.
Future improvement can be done by using remainder of 32kHz
unit drift to reduce this jitter to +/- 16us.
With this fix 20ppm clock accuracy passes conformance TIM
tests (else 251-500ppm had to be used).
Problem was not seen in real life as master do not have a
+/- 16us jitter.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix terminate procedure timeout when supervision timeout
equals connection interval. In this case, avoid timing out
in the first event of procedure initiation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix slave implementation to initiate reject_ext_ind if peer
supports reject_ext_ind.
This fixes:
TP/SEC/SLA/BV-11-C [Slave Sending Reject_Ind_Ext]
conformance test in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix handling invalid control PDUs by generating
LL_UNKNOWN_RSP PDU.
This fixes:
TP/PAC/SLA/BV-01-C [Unknown Packet from Master]
TP/PAC/MAS/BV-01-C [Unknown Packet from Slave]
conformance tests in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix access address generation to correctly have two
transitions in the six MS bits and add other missing checks.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Minor cleanup of Encryption Restart Procedure; No need to
pause rx for slave role on reception of PAUSE_ENC_RSP PDU as
its already paused.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This commit adds http_client_set_net_pkt_pool() function that allows
caller to define net_buf pool that is used when sending a TCP packet.
This is needed for those technologies like Bluetooth or 802.15.4 which
compress the IPv6 header during send.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For IPv6 header compressed packet, the IP header offsets will
be wrong. In this case there is no need to print error when
trying to print TCP packet information.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds http_server_set_net_pkt_pool() function that allows
caller to define net_buf pool that is used when sending a TCP packet.
This is needed for those technologies like Bluetooth or 802.15.4 which
compress the IPv6 header during send.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The buf variable may have been unrefed by net_buf_frag_del thus it shall
not be used to store the sent data nor it should be in the
chan->tx_queue.
Jira: ZEP-2395
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix assert in the controller on master connection creation
due to the CONNECT_IND PDU being transmitted beyond the
calculated scan window.
This is related to commit 80a796b493 ("Bluetooth:
controller: Fix scanner to use correct slot ticks")
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix an assert in next role event preparation when a
connection terminated during the connection event being
aborted/pre-empted out by the next role event.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
CONFIG_MQTT_LIB_TLS is introduced to enable TLS support.
Also, prj_frdm_k64f_tls.conf is added to demostrate the whole idea.
jira:ZEP-2261
Signed-off-by: Aska Wu <aska.wu@linaro.org>
Use net app API since we want to enable MQTT with TLS.
mqtt_connect() and mqtt_close() are added to build and close the
connection to the broker. The caller doesn't need to deal with
the net context anymore and the most of network setup code in
mqtt_publisher is removed.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
As SLIP TAP is now the default after the commit ca0ad13a61
("net: enable SLIP only on QEMU targets"), clarify the comments
and settings in various Kconfig files that talk about slip.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
If the network interface is down, then IPv6 DAD (Duplicate
Address Detection) cannot be done if new IPv6 address is added
to the network interface. This can happen in Bluetooth, where
network interface is taken up only after there is a BT connection.
The DAD is delayed and done later after the network interface is up.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Normally network interface is always UP, but Bluetooth
interfaces are down until connected. So if this is the case,
then check the interface status before trying to access variables
that are NULL. This was seen with "net iface" shell command when
BT was enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In case the application is using NET_L2_BLUETOOTH the SLIP drivr shall
not be selected as bus they cannot coexist since they use the same UART
port:
arch/x86/soc/ia32/Kconfig.defconfig:
config BLUETOOTH_UART_ON_DEV_NAME
default "UART_1"
config UART_PIPE_ON_DEV_NAME
default "UART_1"
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In many networking tests we had to configure SLIP in the prj.conf
leaving those configurations Qemu specific. This change enables SLIP for
QEMU targets automatically and allows reuse of prj.conf for multiple
boards.
Additionally, the TUN options is removed. This option was not used
anywhere.
To enable self-contained networking tests that do not depend on SLIP, we
introduce the new option NET_TEST which disables TAP and allows testing
in QEMU without the need for a host interface.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
* Fix the indentation which was caused by uint32_t -> u8_t changes.
* Make sure there is no unused variable warning if debugging is
enabled but debug level is low.
* Add assert that checks that Imax_abs is > 0 which it should be.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there are no neighbors or there is no route to one specific
neighbor, then check the NULL pointer before accessing the route.
This issue was seen with "net route" shell command.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_stack_analyze function wants to look at the stack buffer,
but it is making assumptions on where this data is that are no
longer valid. Change to use the proper APIs for referencing this.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Since we generate BLUETOOTH_MONITOR_ON_DEV_NAME based on dts we need a
!HAS_DTS check around it. Otherwise we can get into odd build errors.
Its also possibly that we don't specify "zephyr,bt-mon-uart" and in that
case we default to CONFIG_UART_CONSOLE_ON_DEV_NAME (ie 'zephyr,console'
on DTS platforms).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If IEEE 802.15.4 is enabled, then setup the network settings
automatically so that the device is ready for IP configuration.
This is only done if CONFIG_NET_APP_AUTO_INIT is enabled, which
is currently the default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add an initial implementation for the Bluetooth Mesh Profile
Specification. The main code resides in subsys/bluetooth/host/mesh and
the public API can be found in include/bluetooth/mesh.h. There are a
couple of samples provided as well under samples/bluetooth and
tests/bluetooth.
The implementation covers all layers of the Bluetooth Mesh stack and
most optional features as well. The following is a list of some of
these features and the c-files where the implementation can be found:
- GATT & Advertising bearers (proxy.c & adv.c)
- Network Layer (net.c)
- Lower and Upper Transport Layers (transport.c)
- Access Layer (access.c)
- Foundation Models, Server role (health.c & cfg.c)
- Both PB-ADV and PB-GATT based provisioning (prov.c)
- Low Power Node support (lpn.c)
- Relay support (net.c)
- GATT Proxy (proxy.c)
Notable features that are *not* part of the implementation:
- Friend support (initial bits are in place in friend.c)
- Provisioner support (low-value for typical Zephyr devices)
- GATT Client (low-value for typical Zephyr devices)
Jira: ZEP-2360
Change-Id: Ic773113dbfd84878ff8cee7fe2bb948f0ace19ed
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The address lifetime timer was cancelled always even if the address
timer was never installed.
Jira: ZEP-2397
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
poll() allows to (efficiently) wait for available data on sockets,
and is essential operation for working with non-blocking sockets.
This is initial, very basic implementation, effectively supporting
just POLLIN operation. (POLLOUT implementation is dummy - it's
assumed that socket is always writable, as there's currently no
reasonable way to test that.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Use net_context_put(), not net_context_unref(). This makes sure
that after sending response, connections are properly closed.
Jira: ZEP-2362
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Introduce net_context_bind_default() to ensure that local address is
set for context if not yet (via explict bind() call). This fixes
dereferences of NULL pointer to local address which was exposed when
MMU was enabled for qemu_x86.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
When populating the hardware filter, add only slots that are marked as
taken to avoid the hardware being confused by all-0 addresses. This
solves an EBQ issue with whitelist filtering.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To avoid warnings (seen on some machines) that a function reaches its
end without returning a value, conditionally compile the function in a
way that this cannot happen.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix master terminate procedure so that if slave responded to
the ack from master for the LL_TERMINATE_IND then the master
correctly disconnected.
This fixes TP/CON/MAS/BV-09-C [Master Accepting Termination]
in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Tested-by: Ulrich Myhre <ulmy@nordicsemi.no>
Fix implementation to maintain a connection in the slave
role not taking slave latency into use before receiving an
acknowledgement from the master.
This fixes TP/CON/ADV/BV-03-C [Master Missing Slave Packets]
in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Tested-by: Ulrich Myhre <ulmy@nordicsemi.no>
According to RFC7959 page 30, "The end of a block-wise transfer is
governed by the M bits in the Block options, _not_ by exhausting the
size estimates exchanges."
Therefore, we should check the M bit instead of total size (which
is not always available, too)
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
When the controller is configured to have its worker and job
be run at different interrupt priority, check for mayfly
priority being equal was incorrect.
Fixed by conditionally compiling the correct check of mayfly
priority level.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixed a defect wherein anchor for first scanner event was in
the past (when looking for a free timeslice to avoid
overlapping with master role events) when actually there
were no master roles active. This defect caused the scanner
role to assert, when started with other roles active (eg.
advertiser), when trying to catch-up to current tick.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This reverts commit 3c23c6f53d ("Bluetooth: controller:
Fix assert due to stale tick count") as this leads to
connection events to be skipped, failing conformance tests.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This reverts commit b5235207d3 ("Bluetooth: controller:
Fix for scanner Rx window hang") as this leads to
connection events to be skipped, failing conformance tests.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If either UDP or TCP is enabled but not both, then connectivity
fails. This was a side effect of commit 3604c391e ("net: udp:
Remove NET_UDP_HDR() macro and direct access to net_buf")
Jira: ZEP-2380
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When IPv6 fragments were sent, the last IPv6 fragmented packet
was accessing NULL pointer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix calculation of T_Terminate and other procedure timers by
using ceil on calculated connection interval units.
This fixes TP/CON/MAS/BI-02-C [Master T_Terminate Timer] and
TP/CON/SLA/BI-02-C [Slave T_Terminate Timer] in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Ulrich Solli Myhre <ulmy@nordicsemi.no>
Fix implementation so that both slave and master behave same
during connection setup and generate disconnection complete
with reason 0x3e (connection failed to be established).
This fixes TP/CON/ADV/BV-02-C [Accepting Connections
Timeout] in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Ulrich Solli Myhre <ulmy@nordicsemi.no>
Whenever not using the whitelist the resolving list is traversed to
verify that the device is allowed depending on its current privacy mode.
In the case where the device is not found by address in the resolving
list, allow the request to go through, since we are then dealing with an
unknown devices and the resolving list restrictions do not apply.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This causes num of packets command handling to dead lock since it
is done on RX buffer destroy if used on TX it may not be destroyed
on time causing.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The specification states that the AdvA in a Scan Request packet should
be identical to the one sent in the original advertising packet, so
check this when processing a Scan Request.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When the initiator is using an RPA and we match it using the filtering,
we should return early and allow the device packet through instead of
going through the whole resolving list.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The specification states that filter policies shall be ignored for
directed advertising, so reflect this behaviour in the code.
Additionally when the local device is using RPAs but the peer uses an
identity address, the resolving list index needs to be updated when
traversing the RL to reflect that there has indeed been a device match
even though the IRK match did not happen.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The AdvA in the CONN_IND packet must match the AdvA in the advertising
packet that triggered it regardless of the advertising type.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added BUILD_ASSERT check for Tx and Rx thread priorities.
The Tx thread priority shall be higher than Rx thread
priority in order to correctly detect transaction violations
in ATT and SMP protocols. The Number of Completed Packets
for a connection shall be processed before any new data is
received and processed for that connection.
The Controller's priority receive thread priority shall be
higher than the Host's Tx and the Controller's Rx thread
priority.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When the ARP message is received when the device is starting up,
the network interface might not yet have IPv4 address setup
correctly. In this case, the IP address pointer could be NULL
and we must not use it for anything.
Fixes#752
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Coverity reported false positives, add comment about these in
the code.
Jira: ZEP-2344
Jira: ZEP-2345
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch fixes a regression which the original patch introducing
this code (improving concurrent connection handling) had on
*sequential* connection handling. Without this patch, with the
default CONFIG_NET_TCP_BACKLOG_SIZE of 1, after each connection
request, there was 1s (ACK timeout) "dead time" during which new
connection wasn't ptocessed.
This is because k_delayed_work_remaining_get() was checked the
wrong way. But there's no need to use k_delayed_work_remaining_get()
at all, instead just call k_delayed_work_cancel() and dispatch on
its return code.
Note that there's still a problem of synchronizing access to
the global array tcp_backlog, as worker (which modifies it) may
preempt packet handling code (which also modifies it).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The sequence number validator was checking the seq numbers
incorrectly. This caused some valid RST packets to be dropped
and the TCP stream to hang.
Added also a TCP test case that tests the seq validator.
Jira: ZEP-2289
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Usually it is not enough to have just one IPv6 multicast
address defined for the network interface. So allocate three
IPv6 multicast addresses for the network interface as IPv6
by default uses multicast a lot. This hopefully will avoid
some mysterious errors if the addresses run out.
Note that this will increase memory usage a bit so you might
need to lower the count in your conf file if memory is low.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit 210c30805b ("net: context: Close connection fast
if TIME_WAIT support is off") was not a proper way of closing
the connection. So if Zephyr closes the connection (active close),
then send FIN and install a timer that makes sure that if the peer
FIN + ACK is lost, we close the connection properly after a timeout.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit 00ac0487b0 ("net: context: Remove tcp struct SYN-ACK
timer handling") removed also the passive close ACK timer.
Adding that ACK timer back so that we can close the connection
properly even if the last ACK from peer is lost.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This adds a second vendor service testing if service changed indications
works with more than one change in a row and as a bonus it implements
echo attribute which notifies any data that is written to it:
> ACL Data TX: Handle 3585 flags 0x00 dlen 9
ATT: Write Command (0x52) len 4
Handle: 0x0013
Data: 0000
< ACL Data RX: Handle 3585 flags 0x02 dlen 9
ATT: Handle Value Notification (0x1b) len 4
Handle: 0x0013
Data: 0000
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
With introduction of bt_gatt_service_unregister it is now possible to
unregister service at runtime.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There could be situations where many services are changed in a row which
would cause k_sem_take to block on the second change, but if the calling
thread is actually the RX thread then this will deadlock since the RX
thread is the one processing the confirmations of indications and it is
blocked k_sem_give is never called.
To solve this the services changes are now offloaded to the system wq
and the code will attempt to consolidate the range being changed so only
one indication is send. If for some reason another changes is caused
while confirmation is pending we just reschedule it to run later to
avoid blocking the system wq in the same way.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For consistency with the Resolving List, rename the whitelist filter to
match its type and the privacy-enabled version to align it with the
short name used in the RL.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To correctly handle the allocation and deallocation of resolving list
items, the ll_rl_find and wl_pees_find functions have been modified to
return an invalid index instead of a negative value in case of error.
This is to avoid the ambiguity when mixing indices and negative numbers,
which does not play well with the first index 0.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Upcoming memory protection features will be placing some additional
constraints on kernel objects:
- They need to reside in memory owned by the kernel and not the
application
- Certain kernel object validation schemes will require some run-time
initialization of all kernel objects before they can be used.
Per Ben these initializer macros were never intended to be public. It is
not forbidden to use them, but doing so requires care: the memory being
initialized must reside in kernel space, and extra runtime
initialization steps may need to be peformed before they are fully
usable as kernel objects. In particular, kernel subsystems or drivers
whose objects are already in kernel memory may still need to use these
macros if they define kernel objects as members of a larger data
structure.
It is intended that application developers instead use the
K_<object>_DEFINE macros, which will automatically put the object in the
right memory and add them to a section which can be iterated over at
boot to complete initiailization.
There was no K_WORK_DEFINE() macro for creating struct k_work objects,
this is now added.
k_poll_event and k_poll_signal are intended to be instatiated from
application memory and have not been changed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This fixes coverity CID 171565 which may be valid in case of the
connection is not properly setup, or its memory is corrupted, it
may cause use of invalid addresses to be set using
net_if_set_link_addr.
JIRA: ZEP-2344
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the TCP data packet needs to be re-sent after the packet is lost,
then the acknowledgment number will be changed. This then means that
the TCP checksum needs to be recalculated too.
Signed-off-by: june li <junelizh@foxmail.com>
When a node receives consistent DIO messages with same data from
Border Router just ignore those messages. Need not to proceed
further.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Link metric is part IPv6 neighbour data struct. But RPL code is
trying to access it from RPL parent table where link metric doesn't
exist. So provided an api to get IPv6 neighbour data from RPL parent
data.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
DAG rank will be properly written with net_pkt_write_be16() in
network packet. API will take care of endianness. So need
not to convert it using htons().
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Sender rank (16 bit uint) was properly read with net_frag_read_be16()
api and need not to convert it again using ntohs().
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
We had various asserts when checking network packet length but
printed also error when there was none. Fix this by checking
do we really have a too short message.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_TCP_HDR() macro as we cannot safely access TCP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the TCP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_UDP_HDR() macro as we cannot safely access UDP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the UDP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_ICMP_HDR() macro as we cannot safely access ICMP header
via it if the network packet header spans over multiple net_buf
fragments.
Jira: ZEP-2306
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IPv6 HBH option PAD1 ext header was not parsed properly
as the code read one extra byte from the ext header. The
PAD1 length is only 1 byte.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add utility function that helps to figure out if the
protocol headers can be directly accessed when they fit one
net_buf fragment, or if they need to accessed using various
net_pkt helpers that know about reading data from two
different net_buf's.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of directly setting pointer to where to start to calculate
the various IP related checksums, use the net_frag_skip() to first
find out what is the fragment where the calculation should start.
This needs to be like this so that if the IP header + possible
extension are so long that they do not fit the first fragment,
we need to be prepared to look into second fragment.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The following error and warning is received when connecting
to certain central devices:
[bt] [ERR] hci_num_completed_packets: packets count mismatch
[bt] [WRN] bt_att_recv: Ignoring unexpected request
This could happen if Tx-ed packet is not added to pending
list before a num of completed packets event and/or new Rx
packet is received.
This is fixed by reducing the Rx thread priorities in the
Host and the Controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
net_context_unref() is protocol agnostic, after being un-referenced,
the same context might end up being used then for UDP,
if context->tcp is not reset to NULL, calling net_context_unref()
after this UDP usage will again try to release this TCP pointer
which might lead to random error.
Signed-off-by: june li <junelizh@foxmail.com>
The code in send_frag() depends on being able to allocate a new
pending tx contexts with 100% certainty. We must therefore notify
*all* connections instead of the current one in order to ensure that
there are free contexts available in free_tx.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some cases the lladdr might not be set, currently this is
seen with RPL unit tests, in which case we must not access
the lladdr.
Jira: ZEP-2330
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is no route to the neighbor, then do not try to delete
it because the route pointer is NULL.
Jira: ZEP-2329
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move a way from misc/ and put in its own subsystem to allow enhancements
in the future and make it a core part of Zephyr, not just something
misc.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The num_handles parameter of the Number Of Completed Packets event is
8-bits and not 16-bits, so no helper variable or byte order conversion
is needed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case both conn->tx_notify and conn->tx_queue have data in them we
should first process the notify queue and only then new outgoing
packets.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Due to the missing remainder support in the ticker_start
function for first interval, fix implementation so as to
round the first interval/offset during master connection
setup and connection update to within +/-16us.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The SYN-ACK timer is now handled by the TCP backlog functionality,
while the remaining ACKs for established connections use the tcp
struct ack timer. With this, code setting tcp struct SYN-ACK state
timers can now be removed.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Add timer for sent TCP SYN-ACKs. If the timer is already
scheduled to run before canceling it is attempted, set
the cancelled flag and let the callback remove the
delayed work.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Add an array of configurable size that holds TCP backlog entries.
The array is shared between all incoming TCP connections in order
to make it possible to get away with less memory consumed than
with a connection based approach.
The backlog entries are created when a SYN is received for a
listening TCP socket and removed once the corresponding ACK is
seen. With an incoming RST the corresponding backlog entry is
cleared, if any.
The size of the global backlog array is defined with the
CONFIG_NET_TCP_BACKLOG_SIZE Kconfig variable.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
The worst-case maximum number of CCC entries we need is actually
MAX_CONN + MAX_PAIRED. Provide a helper define for it and use it
whenever appropriate.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI Read Remote Version Information Complete event structure was
incorrect, leading to qualification test failures. This patch fixes the
structure and also the storing of the data in an endianness-agnostic
manner.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To avoid manipulation of the irkmatch_ok and irkmatch_id, rely instead
on Resolving List indices for all checks in the advertising ISR.
Although we do incur in a small overhead to look it up initially, the
overall gains are worth the change.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The Controller reserved more than required time for
advertisement event length. Due to this, directed
advertisements did not meet the required <= 3.75ms
interval. It is now fixed by having event lengths based
on the advertisement PDU types.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Correct the default value (0x0) for the Event Mask Page 2 and add the
command to set it to the list of supported commands.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When neither IPv4 nor IPv6 are selected the limit that is
passed to k_sem_init will end up being 0, which will trigger
the folowing assertion in k_sem_init;
__ASSERT(limit != 0, "limit cannot be zero");
Fixed by not passing count as initial and limit value but
only as initial value and use UINT_MAX as limit.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Correctly filter out the Authenticated Payload Timeout Expired event
based on the bit present on page 2 of the Event Mask.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to be able to filter events present in Page 2 of the Event
Mask, this command allows the Host to set the Page 2 of the bitmask
through the corresponding command.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Reset and initialize filters correctly based on whether privacy is
enabled in the controller. Particularly relevant in the case of the
whitelist, which is handled in a completely different way if privacy is
enabled. Additionally reset the peer IRK list in the resolving list
whenever the list itself is cleared.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When flashing in synchronous mode with BLE roles active,
ticker function calls will be deferred to avoid radio ISR
latencies. Increase the total operations supported by 1, to
accommodate flash driver's use of ticker operations.
It has been observed, without this increase, either the
flash driver returned -ECANCEL or the BLE Controller
asserted on data transmit as a slave (trying to force data
transmit on earliest connection event interval).
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Locking interrupts for a long duration is in general bad design, and
is particularly bad for the controller which depends on low latency
interrupts. Instead of using interrupt locking introduce a new flag to
track the shared buffer usage and simply drop characters if the flag
is set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Implement privacy-enabled filtering in the advertiser role. This
includes all required checks when running address generation and
resolution so that the advertiser complies with the relevant
specification sections.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix missing re-initialization of ret_cb to
TICKER_STATUS_BUSY before every new call to ticker interface
functions' with operation's callback.
One issue was undirected advertisement disable to return
failure status in the scan_adv sample.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
With the fix in commit 3c23c6f53d ("Bluetooth: controller:
Fix assert due to stale tick count") it is required that a
skipping event shall abort the previous role in order to
enable the ticker_job to resume and reschedule next ticker
expiry.
In the scan_adv sample, with continuous scanning, an
advertiser would pre-empt it, but if the advertiser skipped
its event without aborting the scanner, the scanner is hung
with its rx window without a timeout, and HCI command to
stop the advertiser will wait forever to complete.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The scanner was reserving a little less slot ticks which
caused other roles to overlap before scan window could
close.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The network application API is a higher level API for creating
client and server type applications. Instead of applications
dealing with low level details, the network application API
provides services that most of the applications can use directly.
This commit removes the internal net_sample_*() API and converts
the existing users of it to use the new net_app API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This doesn't make much practical difference, however it should resolve
Coverity CIDs 170740 and 170748.
Jira: ZEP-2343
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If ICMP packets do not fit in 1 net_pkt fragment the checksum
will be calculated incorrectly.
The problem shows up when using ping with the -s option to
create large ping requests. Eventhough the ping command does
accept the reply without complaining, Wireshark warns that
the icmp checksum is incorrect.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
With the ticker for flash driver added, the Controller was
corrupting memory outside its allocations by incorrectly
using the flash ticker instance to be a BLE role and
corrupting memory. This is now fixed by checking for the
ticker ids to be within the Controller's use before using
them.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In some cases applications may want better control of advertising
instead of the stack doing automated re-enablement. Introduce a new
option that can be used to do more "manual" advertising control.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BT_DEV_ADVERTISING flag already does a suffient job with tracking
the actual advertising state, so there's no need for bt_le_adv_stop()
to return an error if KEEP_ADVERTISING is set. We still need to clear
KEEP_ADVERTISING, but it should not be considered an error if it was
not set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fixed uninitialised auto variables, that had caused compile
errors under CONFIG_DEBUG=y.
Jira: Zep-2334
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If a socket is closed without reading all data from peer or accepting
all pending connection, they will be leaked. So, flush queues
explicitly.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
With CONFIG_NET_SOCKETS_POSIX_NAMES=y, "raw" POSIX names like
socket(), recv(), close() will be exposed (using macro defines).
The close() is the biggest culprit here, because in POSIX it
applies to any file descriptor, but in this implementation -
only to sockets.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This adds Kconfig and build infrastructure and implements
zsock_socket() and zsock_close() functions.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Temporarily, disable scan request notification reports when
LE Advertising Extensions feature is enabled; as support for
enabling scan request notification is not yet added to the
Controller's Link Layer interface functions, yet.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Intention is to test flash driver along with BLE radio.
Added flash shell module with commands for erase, write-check, read and
co-operation with radio stress test.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Extend radio ticker nodes for support in-timeslice execution
Added interface for abort the radio
Added interface for check whether the radio is idle
Added interface for get ticker IDs for timeslice ticker node
Added interface for check whether radio ticker is running
Added interface for check whether radio ticker is initialized
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
In order to associate a hit on the hardware IRK filtering with an entry
of the resolving list, add an array of correspondance between the IRKs
and the resolving list entries.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order for some of the required checks in the ISR to be performed, we
need to keep track of which of the items in the resolving list are in
the whitelist as well. Track them using a single bit in the resolving
list entries.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to obtain the ID (index) of the device matched in a hardware
filter, a new API call has been added along with the required
implementation for nRF5x devices.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When force scheduling a ticker use the number of times the
tickers have already skipped their intervals to decide if
the forced ticker can pre-empt the colliding ticker. This
introduces a fairness amongst tickers contesting for the
overlapping time slice.
Flashing in co-operation with Radio needs to be fair in
order to avoid connection supervision timeouts.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In preparation towards mesh advertise implementation, avoid
one-shot tickers with slots, that have been scheduled to
expire, from being removed by a forced start or update
operation on another ticker.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The global mbedtls heap is set automatically now so no need to
set it individually in the http library.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move the PRNG initialization after reading local supported commands,
so that we don't send HCI_LE_Rand if the controller doesn't support it
(we still need to fail the init however). The patch also removes a few
unnecessary #ifdefs related to crypto.h.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To avoid iterating twice through the list, have ll_rl_find() return the
first free empty slot on the list.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add handling of the LE Set Privacy Mode HCI Command along with the logic
required to take it into account when populating the hardware filters.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order for privacy to work correctly with and without peer IRKs, an
additional hardware filter is required to help match the peer device in
the case address resolution is not possible for a peer since the Host
has not provided a peer IRK for it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When removing a device from the resolving list, if it contained a peer
IRK then it is necessary to update the indices that point to the peer
IRK list, since the list itself is contiguous in memory.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When using privacy, an additional cache of the actual privacy peers is
required to avoid additional processing in the ISR (since some of the
peers in the whitelist will be disabled by the corresponding privacy
settings). Add the cache and populate the actual whitelist just before
advertising, scanning or initiating a connection.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Properly use the role and feature Kconfig variables to populate both the
supported commands and the supported states in the controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the peripheral role depends on the broadcaster one, and the
central role depends on the observer one, select them automatically
instead of using defaults.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Three response codes are missed in zoap_header_get_code() which will
result in the response code returned from the function being set as
ZOAP_CODE_EMPTY. Check include/net/zoap.h for the missing code
definition.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
It's possible that the controller will emit the number of completed
packets event before bt_send() returns, or possibly preempt
send_frag() before it manages to call add_pending_tx(). We have to
therefore add the pending TX entry before calling bt_send().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fixed assert due to stale tick count in role event
preparation. This happens when ticker timeout expiry is
delayed from the requested realtime anchor, due to thread
mode processing overheads and occurring interrupts therein,
if any, that added a delay between requested anchor tick
and actual scheduling for the requested ticker timeout.
The assert is reproduced in bt shell by starting advertising
and following it with continuous scanning (interval 2.5ms,
window 2.5ms), on nRF51x. If the overheads and/or a
advertiser event delayed the scheduling of scanner by over
2.5ms, then the preparation of scanner asserted.
The assert has been fixed by checking for stale tick count
at expiry in role event preparation and skip the event
gracefully.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
For whitelist and resolving list handling, avoid trying to start the
advertiser and scanner roles when they are already running.
Additionally, and since simultaneous scanning and initiating is not
supported, correctly report this to the host both in the supported
states and in the HCI command via an error code, instead of silently
disabling scanning.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
We have conflicting types between the decleration and implementation of
several radio functions. We should be using u32_t everywhere. This
shows up when we try and build with newlib enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added HAL Radio abstractions to use SoC specific Radio Timings
as documented in SoC's electrical characteristics.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In LISTEN state ignore a TCP RST. In SYN RCVD state, reset TCP
connection state to LISTEN when a valid RST segment is received. In all
other states close the connection - except that these other states will
not be handled in tcp_syn_rcvd() function.
Jira: ZEP-2279
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
An OCF is a 10-bit value as defined by HCI, and therefore requires a
16-bit integer to store it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fixed assert due to incorrect implementation of stopping of
advertiser role under directed advertisement timeout, and
also, fixed assert due to adv stop ticker not being stopped
on advertisement disable from thread mode.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added checks for advertiser and initiator/target addresses
received in CONNECT_IND when performing directed
advertising.
This is required to pass TP/CON/ADV/BV-04-C [Directed
Advertising Connection].
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When directed advertisements timed out, connection context
associated was not being released. Subsequent connectable
advertising or connection creation failed.
This is now fixed by releasing the connection context on
directed advertisement timeout.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If the CONFIG_NET_TCP_TIME_WAIT support is disabled, then do not
start to wait for reply to sent FIN in active close, but unref
the corresponding net_context in order to close the connection
as soon as possible.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Refactor whitelist handling into generic filter management in
preparation for future resolving list ID address filters.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Rename bt_gatt_unregister_service to bt_gatt_service_unregister to be
consistent with other APIs such as bt_gatt_service_register.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This initial commit adds the following:
* Handling of privacy HCI commands
* New Link Layer filter module for both whitelist and resolving list
* Advertising RPA generation with timeouts
Follow-up commits will expand the functionality.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Enforce the logical dependency between SMP, RPA generation and privacy
in the Kconfig files for the Bluetooth subsysem.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
For consistency with the return value and to conform with other naming
schemes, rename mem_is_zero() to mem_nz().
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This is unmaintained and currently has no known users. It was
added to support a Wind River project. If in the future we need it
again, we should re-introduce it with an exception-based mechanism
for catching out-of-bounds memory queries from the debugger.
The mem_safe subsystem is also removed, it is only used by the
GDB server. If its functionality is needed in the future, it
shoudl be replaced with an exception-based mechanism.
The _image_{ram, rom, text}_{start, end} linker variables have
been left in place, they will be re-purposed and expanded to
support memory protection.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Use globally available find_lsb_set in Zephyr instead of a
custom find first set function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Moving the net_buf_pool objects to a dedicated area lets us access
them by array offset into this area instead of directly by pointer.
This helps reduce the size of net_buf objects by 4 bytes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The net_pkt_split() was incorrectly checking fragA pointer
even before it was allocated.
The unit test is fixed and converted to ztest.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
gatt-unregister-service can be used to remove the test service at
runtime causing service changed to be indicated:
00:1b:dc:07:31:88 (public)> gatt-unregister-service
[bt] [DBG] gatt_indicate: (0x0011e100) conn 0x0011d880 handle 0x0008
[bt] [DBG] bt_att_req_send: (0x0011e100) conn 0x0011d880 req 0x0011db00
[bt] [DBG] att_send_req: (0x0011e100) req 0x0011db00
Unregistering test vendor service
< ACL Data TX: Handle 3585 flags 0x00 dlen 11
ATT: Handle Value Indication (0x1d) len 6
Handle: 0x0008
Data: 0a001000
> ACL Data RX: Handle 3585 flags 0x02 dlen 5
ATT: Handle Value Confirmation (0x1e) len 0
Jira: ZEP-2225
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
With the introduction of Service Changed support it is now possible to
unregister services at runtime.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds bt_gatt_register_service using bt_gatt_service which contains
the attribute array that is then added to the database saving a pointer
in each and every attribute declared.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
GATT is mandatory service and now that the db can only be build
dynamically there is no reason to keep the applications registering it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
GAP is mandatory service and now that the db can only be build
dynamically there is no reason to keep the applications registering it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes applications able to select the value used for the
GAP appearance attribute.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Removes CONFIG_BLUETOOTH_GATT_DYNAMIC_DB in preparation to the
introduction of bt_gatt_unregister.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In certain cases a response may happen even before number of complete
packets is generated by the controller:
[bt] [DBG] att_req_destroy: (0x0011cfe0) req 0x0011daa0
[bt] [DBG] att_process: (0x0011cfe0)
[bt] [DBG] att_req_sent: (0x0011d780) conn 0x0011d820 att 0x0011d9a0
att->req 0x00000000
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In preparation towards Privacy 1.2, move implementation that
swapped scan response PDU double buffer to same place as
where adv data PDU double buffer is swapped. So that, change
in AdvA in adv data PDU can be reflected in scan response
PDU buffer.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added fix to avoid adv data set function call from
corrupting a ADV_EXT_IND PDU under LE Extended Advertising.
Also, avoid redundant code execution under directed
advertising.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Only ADV_IND, ADV_DIRECT_IND, and CONNECT_IND PDUs can have
ChSel bit set in Advertising channel.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The Bluetooth subsystem assumes execution of its system threads in
cooperative priority, including the system workqueue and the thread
that interact with the controller (i.e. calling bt_send). This commit
adds a compile-time check for the system workqueue priority and
documentation for the bt_send API call.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fixed compile error due to the missing header file
dependency on bluetooth/hci.h, for bt_addr_le_t, in the
Link Layer header file.
Merge of PR #475 introduced the new dependency that broke
compilation after merge of #474.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added a callback function ll_adv_scan_state_cb from the
Controller that gets called on either an advertiser or a
scanner getting started as the Controller's first enabled
state. The callback is also called on the Controller's
last disabled advertising or scanning state.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix missing implementation to reset the advertiser state
when directed advertisements stop without a connection being
established.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add Bluetooth Link Layer LE Advertising Extensions commands
for manual testing the feature during development. First one
being advx command to start non-connectable non-scannable
extended advertising.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In order to reuse code, the reset() function is used both to handle the
reset HCI command but also to initialize the internal HCI variables when
bringing up the system. In the latter case, avoid setting the reset bit
in the state atomic and signalling the polling API, since that is not
required during initialization.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As a preparation for advanced filtering (Controller-based privacy) this
commit refactors whitelisting so that it becomes its own module and
actually correctly performs state tracking to avoid modifying the
whitelist when it's in use.
Additionally it also removes the duplicate separate entries for
advertising and scanning, since the specification only allows one single
global whitelist singleton.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add internal functions to read advertiser and scanner filter
policy if the roles are enabled. This is required to
restrict updates to whitelist and resolving lists when
filter policy are being used by the roles.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Under invalid host behavior, trying to start advertising
while already active would corrupt the advertiser context.
This is fixed by having an explicit flag to check whether
advertiser is already running.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Under invalid host behavior, trying to start scanning while
already active would corrupt the scanner context. This is
fixed by having an explicit flag to check whether scanner is
already running.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
From
http://pubs.opengroup.org/onlinepubs/7908799/xns/netinetin.h.html:
in_addr_t
An unsigned integral type of exactly 32 bits.
[] the in_addr structure [] includes at least the following member:
in_addr_t s_addr
In other words, POSIX requires s_addr to be a single integer value,
whereas Zephyr defines it as an array, and then access as s_addr[0]
everywhere. Fix that by following POSIX definition, which helps to
port existing apps to Zephyr.
Jira: ZEP-2264
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If we receive a HTTP request and if the earlier context is still
active and it is not the same as the new one, then close the earlier
one. Otherwise it is possible that the old context will be left into
TCP ESTABLISHED state and would never be released. Example of this
is that we had IPv4 connection active and then IPv6 connection is
established, in this case we will disconnect the IPv4 connection
after this commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Given that K_NO_WAIT is passed as a timeout to net_context_recv(), it's
unlikely this function will return any error value. It's cheap to
check, though, so do it.
Coverity-CID: 170580
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The shell takes care of removing the module name so it is no longer
necessary to have this adjustment.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The command callback might not recognize commands if the input comes
with the module name as first parameter as both argc and argv will be
off by one.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the command cannot be execute code should return a proper since this
may not be a user input.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds shell_exec which can be used to execute commands directly
without the use of a console which is useful for both testing as well
as interfacing with applications/upper layer which would like to have
access to shell commands directly.
In addition to that this may be more trivial to interface with instead
of using fifos like uart_register_input and telnet_register_input do.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In certain TCP states we should not try to send RESET segment
to peer. So check this and do not try to use NULL pkt to send
a message.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The "net http monitor" command turns on HTTP monitoring,
which means that for each incoming HTTP or HTTPS request,
a information about source and destination address, and
the HTTP request URL is printed.
User can disable the monitoring by "net http" command.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If CONFIG_NET_DEBUG_HTTP_CONN is enabled, then start to collect
currently active HTTP connections to HTTP server.
This is only useful for debugging the HTTP connections.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Restrict encryption support on nRF51 series SoC to Bluetooth
LE 1M PHY and max. 27 bytes PDU. If 251 bytes PDU using Data
Length Update procedure is desired, then LE Encryption
procedure will not be supported (until a software CCM is
implemented in future).
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add Kconfig option to be able to conditional compile the
Bluetooth v4.0 LE Encryption procedure.
This is needed in order to be able to not support encryption
on nRF51 series when using Data Length Update procedure with
upto 251 byte payloads until a software-based CCM support is
implemented.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If we cannot send network data, then print the error code when
printing debug information about the issue. This is needed when
debugging the issue.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add HTTPS support into http-client library. The init of the
HTTPS client connection is different compared to HTTP client,
but the actual HTTP request sending is using the same API as
HTTP client.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is done so that both http_client and http_server functionality
can share the same heap.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When src and dst addresses are compressed based on context
information, uncompression method should verify CID bit,
SAC and DAC bits and context ID's. But it has missed some
cases which resulted in invalid uncompressed IPv6 header.
e.g. CID is set, SAC is 0 and DAC is 1 and context id's provided.
Uncompression method assumed that src address is compressed based
on context information but it is not.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Empty RPL HBH header will be inserted while finalizing IPv6 packet
but updated after finding nexthop and sent the packet. In case of
Bluetooth or multicast dst address it was missed. Resulted in
empty RPL HBH header and packet dropped at peer node. It should
be updated in all circumstances.
Jira: ZEP-2088
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The mbedtls debugging function was set before the ssl config
struct was initialized. This meant that it was not possible
to activate mbedtls debug prints. This commit sets the debug
print option after the config struct has been initialized.
Fixed also the debug prints which print extra \n which looks
very bad in debugging outputs.
This commit does not enable mbedtls debugging, it just makes it
possible to output mbedtls debug prints. In order to get mbedlts
debug prints one needs to do this:
* set DEBUG_THRESHOLD to >0 in http_server.c
* enable CONFIG_NET_DEBUG_HTTP in project config file
* enable MBEDTLS_DEBUG_C in mbedtls config file (see file pointed
by CONFIG_MBEDTLS_CFG_FILE option)
* in qemu, one needs to increase the size of the available RAM,
this setting does the trick, CONFIG_RAM_SIZE=300
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Semantics of ENOENT error as used previously is "named entity not
found", whereas for "I/O handle is not valid", there's EBADF. For
example, POSIX/SUSV2 doesn't even list ENOENT as a possible error
for accept(), connect(), recv(), etc. whereas it lists EBADF, e.g.:
http://pubs.opengroup.org/onlinepubs/7908799/xns/connect.html
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add a repeat param to gatt-write-without-response so that
it covers what gatt-write-without-response-repeated was
doing. gatt-write-without-response was removed in the
commit 26eae70da.
gatt-write-signed too will have repeat param with this
change.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
At the moment all bluetooth logs are prefixed with [bt] making it
difficult to understand where the logs belong to.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Instead of waiting forever for a free net_buf, set a timeout to
the allocations (500 ms). This way the application will not be
blocked by memory exhaustion.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In some cases the net_pkt can be null when freeing it,
this will print error from net_pkt library. Avoid this by
checking the value of net_pkt before calling net_pkt_unref().
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we re-connect to same peer server, then we should select a new
source port. Noticed that if the same source port as before is
used for the new connection, the peer might drop the packet. This
was seen when connecting to Linux peer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Defines a new tunable, CONFIG_NET_TCP_RETRY_COUNT, that determines the
number of segment retransmissions that the IP stack will attempt to
perform before resetting the connection.
The default value is 9 retransmissions, which amounts to 1:42 minutes,
as close as possible to the minimum recommended by RFC1122.
Jira: ZEP-1956, ZEP-1957
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
It's mandatory to set chan->ops so explicit checks for it are
redundant. What's worse, inconsistent checking for this triggers
static code analyzer warnings. This patch fixes Coverity CID 151984.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
buf->len should be validated before accessing it since remote can
send invalid frame_len which can result in out of bound memory
access.
This also fix the len check wrt cstate, since current check is
not considering the cstate length size and frame_len size.
Jira: ZEP-2110
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Added shell module for the Bluetooth Controller's ticker
interfaces.
For now, info command enumerates active tickers' details.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If we receive unknown option in neighbor advertisement message,
then skip those properly. Old code did not check the length of
the extension options which could cause infinite loop.
Jira: ZEP-2219
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
If we received a bad HTTP request, then subsequent good requests
were also returning 400 error code. The parsing state needs to
be initialized after each received HTTP request.
Jira: ZEP-2181
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fixes the following issue:
"In expression 1UL << chan - 1U, left shifting by more than 31
bits has undefined behavior. The shift amount, chan - 1U, is
4294967295."
Coverity-CID: 167140
Jira: ZEP-2131
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
In console shell, add explicit, 'exit' command to leave the current
module. Currently this is being achieved by overloading select command
(without an argument).
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
This makes gatt-write-signed to reuse cmd_gatt_write_without_rsp since
it is quite similar and that adds the ability to send multiple octecs
instead of just a single byte.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes gatt-write-without-response-repeated and makes
gatt-write-without-response similar to gatt-write which was the
intention of gatt-write-without-response-repeated.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
All the files under shell subdir shall only be build if
CONFIG_BLUETOOTH_SHELL is selected.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In order to properly queue request there need to be a bt_att_req
storage but none of the calls to gatt_write_ccc were using the params
causing gatt_send to use bt_att_send and not bt_att_req_send.
To fix this now all the callers of gatt_write_ccc do set the params
properly but this means that bt_gatt_unsubscribe has to wait for it
to be completed before the application can reuse the
bt_gatt_subscribe_params.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Print also network buffers that are allocated by the IPv6
fragment handler. This is very useful in debugging.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the user really wants, it is possible to increase the
maximum size of the fragmented packet. According to RFC 2460
chapter 5, we do not need to accept larger than 1500 byte IPv6
packets, so the max pkt limit is set to 2. But if really needed
the limit can be raised by defining NET_IPV6_FRAGMENTS_MAX_PKT
to some new value. Currently there is no Kconfig option for
doing this as it is unlikely that this is needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The cancellation of reassembly did not work as expected because
K_WORK_INITIALIZER() did not setup the timeout function properly.
So do the timer initialization at runtime instead.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IPv6 fragmentation was not working properly when the large
IPv6 packet was being sent. There is unit tests in next commit
that will test the IPv6 fragmentation sending.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the fragmented IPv6 packet was very large, we could run out
of resources. When that happened, we leaked the memory for the
pending fragments that were waiting reassembly.
Jira: ZEP-2166
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The previous default 60 seconds is way too long for our limited
amount of memory. It might be that the 5 sec is still too long
but that can be changed in the future.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
While returning 32-bit values from radio status interfaces,
explicitly compare radio h/w event registers to be non-zero,
dont just return the direct 32-bit h/w register content.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added extra assert checks to detect controller failure if
a role event preparation function was not followed by the
role event start function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Shell itself already have a help command, so instead of creating a net
specific help just fill the help description of each command.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Shell modules are registered at link time thus it makes no sense to
leave it behind net_shell_init.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the HTTPS connection is closed, then properly handle call to
HTTP parser init in case of error and also remove any pending
data that belong to old connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive unknown option in neighbor solicitation message,
then skip those properly. Old code did not check the length of
the extension options which could cause infinite loop.
Jira: ZEP-2174
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we could not split the packet properly, make sure that the
fragments that we managed to allocate are unreffed and marked
as NULL.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print also the character when hexdumping a memory area.
This is useful so that one does not need to convert hex
values to characters in head. Unprintable chars are printed
as '.'
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For some write requests, such as CCC, the code doesn't use an ATT
request context but we still need to clear the request timeout when
the response comes. Move the k_delayed_work_cancel() call to the right
place and add some debug logs that helped pinpoint this issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Both scan on and scan passive performed passive scanning,
fixed scan on command to use active scanning.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In commit c41d3edda when implementing the alternative
encryption setup implementation, the original fast
encryption setup implementation was broken. When host is
slow in responding to LTK request, the controller asserted
when fast encryption implementation is selected. This is
now fixed.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix the assert in the controller during connection setup
when peer does not support CSA#2 feature and free Rx buffer
queue does not have enough buffers to generate CSA event.
The assert was reproduced by turning on advertisement
indication and scan request notification features in the
controllers advanced features, and a peer that does not
support CSA#2 initiated a connection.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Since role support is fundamental to both the Host and the Controller,
move the role configuration options to the top-level file and rename
them to fit the GAP specification, avoiding confusion between GAP and LL
names.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Only include connection-related options when CONFIG_BLUETOOTH_CONN is
selected, since otherwise this can lead to inconsistencies between
features and supported commands.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This replaces the use of shell_register_prompt_handler with
SHELL_REGISTER_WITH_PROMPT which doesn't overwrite other modules
prompt.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enables modules to define its own prompt handler instead of always
using the default_module_prompt.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If CONFIG_BLUETOOTH_GATT_CLIENT is not defined disable command that
would depend on it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to several changes in the way stacks are calculated, 320 bytes is no
longer enough for the controller-only build. After measuring usages of
up to 320 bytes (locally) and 376 (reported by Ricardo Salveti), the
stack size is increased by 128 bytes, up to 448 bytes.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The msgtype value is created using 'hdr & 3' which means that the
resulting value can never be greater than 3. This fixes Coverity CID
166771.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
No need to check attr and path variables for null as they
cannot be null.
Coverity-CID: 157595
Coverity-CID: 157602
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Added implementation to auto-update LE Data Length to max.
Tx octets supported by the local and peer controllers.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added implementation to handle an incoming Reject Ext Ind PDU in
response to a sent Length Req PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When initiating Data Length Change at the same instant the
crossover condition was not handled correctly causing the
controller to assert.
This fix will allow crossover of Data Length Update
procedure, and this collison is harmless as per Bluetooth
specification, and gracefully handled by the controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Return error codes for HCI Tx buffer overflow conditions are
missing which would lead to silent dropping of Tx packets if
host implementations do not follow number of completed packets
or use correct buffer counts as returned by HCI Read Buffer
Size command.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Allow the caller to delay the closing of the HTTP connection
for a number of milliseconds. The purpose for this is that
the client can send still some data back to us for a short
period of time.
This is needed for example for Basic authentication so that
server is able to receive authentication values back.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Since the PHY update complete event can be generated due to the
procedure being initiated by the peer, use a flag to
differentiate between local auto update initiated on connection
complete versus peer initiated anytime in the connection. This
is necessary to avoid repeated initiation of auto-update
procedures intended only to be issued on connection complete.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The address family of the UDP port listener was not set. This
caused weird debug prints in net-shell. Now the listener will
be registering IPv4 any address as it should.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When a connection handler was registered, the checker function
introduced in commit 43b37cef ("Check duplicate UDP/TCP connection
handlers") did not check the address family (IPv4 or IPv6) of
the local end point properly. This caused duplicate connection
error to be returned to the caller.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The uncompressed source address in packets was not handled properly if
NET_6LO_CONTEXT was enabled.
This implementation is identical to the contextless case.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
If we do not receive last ACK when the connection is tore down,
then do not wait forever as that would eat all the resources in
the network stack. So when we enter the LAST_ACK state, we setup
a timer that will unref the connection if the last ACK is not
received.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Without change to add ACK to FIN, invalid TCP packet is generated,
where ack sequence number is non-zero. Without adjusting sequence
number as done, ACK which we send in response to peer's FIN/ACK is
not recognized by peer, and peer keeps retransmitting its FIN/ACK.
Jira: ZEP-2104
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
When connection handler was unregistered, we did not remove
it from cache. This caused invalid connection to be passed to
net_context after connection unregister if connection caching
was enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We did not check UDP or TCP checksum to be valid after receiving
the packet. Fix this so that the checksum is validated when
packet is received in connection handler. As the checksum validation
can be resource intensive, do it after we have verified that
there is a connection handler for this connection.
The checksum calculation can be turned OFF if needed, but it is
ON by default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit "net: tcp: Handle retransmitted packets from peer"
introduced over 80 character line that was missed in review.
Fixing it now.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user has enabled RPL and STATISTICS, then enable RPL
statistics by default as that is probably what user want.
Same thing for MLD statistics.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When we receive a packet with the sequence we already seen (and
processed), the most likely cause of it is that our ACK was lost,
and peer has to retransmit that packet. Then, we should just ACK
it, because otherwise peer will retransmit it again and again,
falling into exponential backoff and hosing the entire TCP
connection.
This makes changes to send_ack(), adding a flag to force sending
an ACK regardless of its cached status, and remove inline modifier,
as the function is big and called from many places.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
We must check if we receive RST in any of the TCP states.
If we do not do this, then the net_context might leak as it
would never be released in some of the states. Receiving RST
in any TCP state is not described in TCP state diagram but is
described in RFC 793 which says in chapter "Reset Processing"
that system "...aborts the connection and advises the user and
goes to the CLOSED state."
We need to also validate the received RST and accept only those
TCP reset packets that contain valid sequence number.
The validate_state_transitions() function is also changed to
accept CLOSED state transition from various other states.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
With the support for 2M PHY added, the controller can now Rx/Tx
upto 18/19 minimum sized L2CAP packets per 7.5ms connection
intervals.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
net_if_get_default() was documented as returning "Default interface
or NULL if no interfaces are configured.", but actually didn't
return NULL in the latter case. Instead, it effectively returned
a pointer to random area of memory, shared with other system
structures, so calling functions like net_if_ipv4_set_netmask(),
etc. could trash unrelated memory.
Jira: ZEP-2105
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
RFC793, "Transmission Control Protocol", defines sequence numbers
just as 32-bit numbers without a sign. It doesn't specify any adhoc
rules for comparing them, so standard modular arithmetic should be
used.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
To better debug the flow of events into the Host, log the subevent code
whenever processing an LE Meta Event.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When required Rx MTU is less than configured Rx MPS, the
resultant initial credits was 0 which prevented any L2CAP
packet to be received.
Fixed by ceiling the initial credits count in the credits
calculation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This places a sentinel value at the lowest 4 bytes of a stack
memory region and checks it at various intervals, including when
servicing interrupts or context switching.
This is implemented on all arches except ARC, which supports stack
bounds checking directly in hardware.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Sometime it is observed on the Arduino 101 that when we write more than
4 bytes into TX USB Endpoint, first 4 bytes are getting repeated
(frequency of occurrence ~1/3000).
This patch does following :-
1. In sample application "cdc_acm", it adds capability to
handle partial transfer data incase data is transferred partially
if exceeds maximum data transfer size.
2. It restricts write of more than 4 bytes into TX USB Endpoint.
This is work around to avoid issue occarance.
Jira: ZEP-2074
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit creates a HTTP server library. So instead of creating
a complex HTTP server application for serving HTTP requests, the
developer can use the HTTP server API to create HTTP server
insteances. This commit also adds support for creating HTTPS servers.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When a new UDP or TCP connection handler is to be registered,
we need to check if identical handler has already been created.
If a duplicate is found, the registering call will return -EALREADY.
The earlier code did not check this but allowed two identical
handlers to be created. The latter handler was never called in
this case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This helper copies desired amount of data from network packet
buffer info a user provided linear buffer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
To be consistent with other subsystem menu, use menu for
Bluetooth support in Kconfig instead of menuconfig which
showed up as checkbox.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To allow for hci_uart builds that do not include the controller code,
move the UART Kconfig option used by the sample up one level so that it
is shared by all configurations using Bluetooth:
Jira: ZEP-2132
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since more and more code is going to be reused by both the Host and the
Controller, this commit introduces a common/ folder that will contain
everything that is not tied to one of the two components but shared by
them.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This reverts commit 698de88916 ("Bluetooth: controller:
Cleanup redundant ticker busy loop")
Scan enable asserted in ctrl.c line 3756 due to the fact that a
role event was active and ticker job has hence been disabled.
Add back the busy loop so that scan enable can wait until the
active role event completes gracefully.
The ticker busy loop is mandatory in all ticker interface calls
if a blocking behavior is desired.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The calculation in packet_rx_reserve_get() was already handled by
packet_rx_acquired_count_get(). So, let's use that code instead
and remove the duplication.
Change-Id: Ic76f70f1e78bebc74f5bef36cd92a3c332e489e9
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This calculation can be used in packet_rx_reserve_get() where currently
the code is duplicated from packet_rx_acquired_count_get().
Let's allow use of packet_rx_acquired_count_get() regardless of whether
CONFIG_BLUETOOTH_CONTROLLER_DATA_LENGTH is enabled.
Change-Id: I613bde0a407f3caccabb22f369098575965e98ad
Signed-off-by: Michael Scott <michael.scott@linaro.org>
During testing, lr->max_rx_octets and lr->max_tx_octets were
at times set to 0. If we use these 0 values, we end up with
very erratic behavior. Best, to check for a sane value and
if invalid, default to the value in _radio.conn_curr->max_*x_octets.
Change-Id: I57c0e3790d988f0de17993cebe5c5c2ab0fc07a6
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When Controller to Host flow control is enabled, output informational
messages for certain operations to help tune and debug the feature.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the HCI driver debug option applies to both files in
drivers/bluetooth and subsys/bluetooth, the configuration option itself
now lives in the top-level Kconfig file for consistency.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added implementation to auto-update Bluetooth PHY to 2Mbps
if the local Controller supports it.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added support for Bluetooth v5.0 PHY Update Procedure in the
Controller.
Asymmetric PHY connections do not work for now due to the
Radio mode not being setup in time in the ISR during tIFS
period and the Radio already ramping up in the cached
previous Radio mode to meet tIFS deadline.
Subsequent commits will add this feature, by either double
buffering the mode in software or using fast radio ramp up
which gives enough time in the ISR to change the mode.
Jira: ZEP-2086
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Scale the ctrl pkt enqueue implementation to allow multiple
ctrl packets to be enqueued. This will aid in the graceful
implementation of parallel control procedure collisions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added HCI macros to check LE Features. Also, added test
macros for 2M and Coded PHY support in HCI Controller.
Earlier a common test macro was used between BR/EDR and LE,
but since LE features do not use pages for feature, an
explicit macro for testing LE feature is added now.
Also, features field in LE device structure is now a single
dimension array of 8 octets.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The APIs for allocating RX buffers were modified recently and hci_raw
had not reflected those changes properly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When we send TCP data segment, we need to set the length
of the application data by calling net_pkt_set_appdatalen().
This is done so that sequence number can be properly
advanced when we receive ACK to that pending packet.
Signed-off-by: xiaorui hu <xiaorui.hu@linaro.org>
fix misspelling in Kconfig files that would show up in configuration
documentation and screens.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The event mask population used to let the Controller know which events
are relevant to the Host needs to take into account the features
supported by the Controller itself, in order to only enable those that
are indeed valid.
Jira: ZEP-2050
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the framework for LE Scan Request Received Event.
The feature is available under the Controller's advanced
features and will be selected implcitly when Bluetooth v5.0
LE Advertising Extensions feature is implemented.
Jira: ZEP-2073
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove unreferenced function hci_evt_is_discardable after
introduction of hci_get_class function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In preparation for refactoring the Controller implementation
into seperate state and role based source files, add Kconfig
options for states and roles in the Controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To guarantee code that is endianness-independent, the sys_le* macros
must be used everywhere when accessing multi-byte values from the
command parameters.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In HCI, the response buffer to a command is the same as the one for the
command itself, requiring command parameters to be processed before the
response is formed on the same memory area.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Instead of separate sample application that does everything
related to HTTP client connectivity, create a HTTP client library
that hides nasty details that are related to sending HTTP methods.
After this the sample HTTP client application is very simple and
only shows how to use the client HTTP API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Since Controller to Host flow control is a feature that affects both
sides equally, move it to the top-level Kconfig file and consolidate its
use in both Controller and Host.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This feature was removed some time ago, but turns out it's important
to have it available for split host-controller setups.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Enable the bits corresponding to the new 3 commands supported when
enabling Controller to Host Flow Control, in order for the Host to be
able to enable the feature.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to achieve proper sharing of configuration options, everything
that is common to both the Host and the Controller should now be placed
in the top-level Kconfig file, and Controller-only options are in the
controller/ Kconfig one.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Introduce alternative TRX switching using dedicated timers
and peripheral interconnect. This will enable the
possibility to independently configure the Tx and Rx
settings between the tIFS.
Note, this will also provide the opportunity to design a
soft realtime Radio ISR.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The Bluetooth Specification allows for optional Controller to Host flow
control based on the same credit-based mechanism as the Host to
Controller one. This is particularly useful in 2-chip solutions where
the Host and the Controller are connected via a physical link (UART, SPI
or similar) where the Host is sometimes required to ask the Controller
to throttle its data traffic while still making sure that relevant
events get through the line.
This implementation is based on a simple queue of pending events and
data that is populated whenever the Controller detects that the Host is
out of buffers and then emptied whenever the Host notifies the
Controller that is ready to receive data again. Events relevant to the
connections are also queued to preserve the order of arrival.
At this point the Controller ignores the connection handle sent by the
Host and treats all connections equally, and it also queues events even
for connections that have no data pending in the queue. Both this items
can be improved if necessity arises.
Note that Number of Completed Packets will still flow freely from the
Controller to the Host regardless of the pending ACL data packets, which
might lead to inconsistencies in the sequential order of certain
operations that include bi-directional data transfer.
Jira: ZEP-1735
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When adding link-local address to the cache the type needs to be
properly set as net_ipv6_addr_create_iid will attempt to use it
when generating the IPv6 address.
Jira: ZEP-2077
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This is related to commit "net: tcp: Make sure ACK timer is not
run if cancelled" which did not set the cancel flag when the timer
was cancelled from tcp.c.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
And print a warning if that happens.
This will also avoid to raise an ASSERT on net_if_tx_thread()'s k_poll
as this one will be called with no events to work with.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This ensures that an unknown request won't cause ATT to timeout since
no response is currently generated.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Rename ll_address_* to ll_addr_*. Also, update ll_addr_get
to return reference to stored public or random address.
Change-id: I22cb0135d2223f679c4d9321f4724f8b7de0aede
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Fix the attr->handler reference to attr->handle.
Change-Id: I4a6ccee7860abf800f51df404979eac18eb26e8e
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Rename occurences of bt_hci_ev_* to more widely used
bt_hci_evt_* namespace.
Change-id: I742fb86f8f835a0f6072638e1e997ad08891d43d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
In the Controller's radio hal, explicitly differentiate
between Advertisement and Data channel packet
configuration.
Also, remove nRF5x specific extra overhead in Advertisement
PDU structure.
Change-id: I942b88a160af78f8900d7e49fb5f36c8aa493b97
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
L2CAP Dynamic Channel feature uses the global connection Tx
pool for segmentation either when there is no free buffers
in the original application pool or when the original data
buffer has no headroom to add L2CAP headers.
This eliminates the need for a dedicated fallback pool for
Dynamic Channel segmentation.
Change-id: Ia5452c814169d17ef261ecef425a8fcf2e7e1e84
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
This function already has an 'i' variable on the top-level, so no need
to declare a second one that'd just shadow the original.
Change-Id: I5dfa4df2c4793be220a40ac642b19bf440e80220
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The segment allocation function can't fail (it eventually waits with
K_FOREVER for a buffer to become available), so there's no point in
checking its return value for NULL. Also, the connection state check
is because of this particular waiting and not the semaphore waiting
(which is done with K_NO_WAIT).
Change-Id: I9698760541de810869cffc1c60cf97c5f8f7df8d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
L2CAP Tx segmentation used BT_L2CAP_RX_MTU value which is
the value used by fixed channel protocols. Decoupling the
buffer size provides the opportunity to reduce RAM used per
connection.
Change-id: Id064f9b2e3f02073402815d09c3ea13a35df2a6c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Remove BT_ prefix from BT_L2CAP_MAX_LE_MPS and
BT_L2CAP_MAX_LE_MTU as they are internal to l2cap.c file.
Change-id: I6abec0a1f07b8aef49940ab7abeaacbd19947e0b
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The switch from C99 integer types to u16_t, etc. caused misalignment
in structs and function definitions with multi-line parameter lists.
Change-Id: I1448b159ab1afe50ff88b7a6bd1b254c44858d4c
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This information should be part of the main BR/EDR context struct,
rather than there being a separate member in struct bt_dev. If/when
the needed ESCO information grows we can consider having a separate
struct, but even then it should be part of the main BR/EDR struct
instead of sitting directly in bt_dev.
Change-Id: I3edf120606ea6c6974f515bba90de2b25fc6fac6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The switch from C99 integer types to u16_t, etc. caused misalignment
in structs and function definitions with multi-line parameter lists.
Change-Id: Ic0e33dc199f834ad7772417bca4c0b2d2f779d15
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This should fix the grouping for debugging options appearing in the
main "menuconfig" menu.
Change-Id: I7ddf3a6f3d025bf82ba63099b30e47a40d7c3187
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The highest endpoint number supported by the STM32F4xx USB device
controller is 3. Change the cdc_acm driver to use endpoint 2
instead of endpoint 4 so that it will work with this platform.
Change-Id: I4a3cd08f546a7fe01558528de0990156f642d93b
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Instead of returning EIO let's bubble the error from net_context_send
back up to the caller in the following functions:
mqtt_tx_connect()
mqtt_tx_disconnect()
mqtt_tx_pub_msgs()
mqtt_tx_publish()
mqtt_tx_pingreq()
mqtt_tx_subscribe()
mqtt_tx_unsubscribe()
Change-Id: I9bb4396b227b8902ac1195a97bc37eb1959b643e
Signed-off-by: Michael Scott <michael.scott@linaro.org>
With CONFIG_NET_DEBUG_NET_PKT enabled, the log messages are full of
errors regarding NULL parameters passed into net_pkt_unref in almost
every TX function for handling MQTT messages:
mqtt_tx_connect()
mqtt_tx_disconnect()
mqtt_tx_pub_msgs()
mqtt_tx_publish()
mqtt_tx_pingreq()
mqtt_tx_subscribe()
mqtt_tx_unsubscribe()
mqtt_parser()
Let's clean up the unref handling so that our debug log isn't quite
so full of error spam (as opposed to the normal amount of spam from
the net buf log).
Change-Id: Ib49d1192f51abe4329e6dc9da3c51a4a36290082
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The data->len of an inbound netbuf can be larger than a single
MQTT packet. For instance when a PINGRESP is also included
in the same netbuf. For this reason we should not be using
the data->len to determine how large the rest of the MQTT data is.
Specific Example: we've seen in testing that PINGRESP packets
can be included with a SUBACK packet in the same netbuf. Under
this case the current code uses the data->len incorrectly and
tries to find 3 QoS elements for the SUBACK packet when there
is only 1 (the rest of the data is for PINGRESP).
NOTE: A larger patch to iterate through the netbuf data parsing
individual MQTT packets will be needed to fix the MQTT subsys.
This patch only corrects the SUBACK parsing.
Change-Id: I7f6cebaaed9570b778d466de84331cf8c5060755
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Currently, app type MQTT_APP_PUBLISHER_SUBSCRIBER is not supported.
mqtt_init() will return EINVAL because the context rcv function is
either mqtt_publisher_parser or mqtt_subscriber_parser (not both).
Let's combine these functions into mqtt_parser and remove the app
type check from mqtt_init().
Change-Id: I60460e011395864706e293c997e9f8a65681b368
Signed-off-by: Michael Scott <michael.scott@linaro.org>
We need to set the mqtt context recv function prior to calling
net_context_recv which installs the mqtt_recv callback.
If not, we risk a race condition where an unprotected reference
to mqtt->rcv(mqtt, buf) is made in mqtt_recv().
Change-Id: If90ee58f4ea6f7879ef7c12b969ba27647426acc
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Some applications may want to reuse implementations of these
commands for debugging/diagnostics purpose even if they don't
use net shell per se, or implement an alternative shell.
Jira: ZEP-2064
Change-Id: I48cb66ccc41bd41a75a4eb8eb3c366316ec5a096
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
net_if_ipv6_router_add() will return router pointer on success.
This information must be cached in RPL instance, otherwise RPL
instance doesn't know about default route.
Change-Id: Ic6d80ebfa95c9a64df9adf2621ae2631d9bdb990
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When router or default router timer expired, interface will remove
router from the list. In this case RPL does not know about this.
When RPL node receives DIO messages it only verifies whether parent
exists or not. This extra checks will verify whether router really
in "used" state or not.
Jira: ZEP-2080
Change-Id: I4b36b3a2d495e76a38caddd058451daff08fab0c
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
net_if_ipv6_router_rm() is the correct API to remove IPv6 router
from the interface as it also cancels the timer and raises a mgmt
event. The net_if_router_rm() only sets router as unused and
nothing else.
Change-Id: I55114288c9ae748520b67b206edcd4f5e420b1af
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If the ./well-known/core response is bigger than L2 MTU then
response will be sent in multiple fragments. In mesh kind of networks
getting response from farthest node might loose packets. So better to
send response in a block wise fashion. Block size is configurable.
Change-Id: Id421c66597fe448c12a7215f04f63f4a284c14ab
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Value 0xFF represents End Of Options marker in CoAP message.
Use #define than magic numbers in code.
Change-Id: I3bef21ea827987f7c2e670447ee20574cb6288ae
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Add timeout for packet and buffer requests. If there are no
buffers available gracefully drop the request.
Change-Id: I56fe2b606556149c83751aadc1c5eee7828a84a8
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Bluetooth only cares about the actual payload so net_pkt can be unref
as soon as the data fragments are detached.
Jira: ZEP-2070
Change-Id: Id528d5440f42903378883f5e696b3f663bbfa313
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For stream-based protocols (TCP), adding less data than requested
("short write") is generally not a problem - the rest of data can
be sent in the next packet. So, make net_pkt_append() return length
of written data instead of just bool flag, which makes it closer
to the behavior of POSIX send()/write() calls.
There're many users of older net_pkt_append() in the codebase
however, so net_pkt_append_all() convenience function is added which
keeps returning a boolean flag. All current users were converted to
this function, except for two:
samples/net/http_server/src/ssl_utils.c
samples/net/mbedtls_sslclient/src/tcp.c
Both are related to TLS and implement mbedTLS "tx callback", which
follows POSIX short-write semantics. Both cases also had a code to
workaround previous boolean-only behavior of net_pkt_append() - after
calling it, they measured length of the actual data added (but only
in case of successful return of net_pkt_append(), so that didn't
really help). So, these 2 cases are already improved.
Jira: ZEP-1984
Change-Id: Ibaf7c029b15e91b516d73dab3612eed190ee982b
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Instead of just plain assert, check that the packet we receive
is ok before passing it to processing function.
Jira: ZEP-2057
Change-Id: I5754c82d16e1522d8fcee561eea280eadeec31ee
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The TCP trace values were not printed because of incorrect
config option used. Print also seq and ack values in decimal
in order to make it easier to correlate the values in other
prints in tcp.c.
Change-Id: I44d1535a84dcba8c6c937d348516ba801193ca23
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use ready-made utility function which can take care of endianness
Change-Id: I1edd0b2ce1a086dd637e97308145f9b434e48a1f
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
When connect to diffrent router with the same gateway ip address,
need to clear arp cache when disable interface,
or it will use the wrong gateway mac address.
Call net_arp_clear_cache function replace to set arp_table 0.
Change-Id: Ib403a0c0030832ba48824db4d2d3fcb8add63d16
Signed-off-by: june li <junelizh@foxmail.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Change-Id: I9ccb7c01a7d8c4ad8b1e55a1b45622aad2a57e57
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds a new event type to the kernel event logger that tracks
thread-related events: being added to the ready queue, pending a
thread, and exiting a thread.
It's the only event type that contains "subevents" and thus has a
non-void parameter in their respective _sys_k_event_logger_*()
function. Luckily, as isn't the case with other events (such as IRQs
and thread switching), these functions are called from
platform-agnostic places, so there's no need to worry about changing
the assembly guts.
This is the first patch in a series adding support for better real-time
profiling of Zephyr applications.
Jira: ZEP-1463
Change-Id: I6d63607ba347f7a9cac3d016fef8f5a0a830e267
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: Icbf9e542b23208890a3a32358447d44cdc274ef1
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I4ec03eb2183d59ef86ea2c20d956e5d272656837
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There was compiler error if CONFIG_NET_DEBUG_CONN was set.
Change-Id: Ibb6721c55dd2c56cd0097359a53563c6221859ea
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need to set the connect_cb for the context before sending SYN packet.
This is required if we have a loopback connection in which case everything
is happening more or less synchronously and the connect_cb would not be
called in this case because its value would still be null.
For remote network connections this patch makes no difference.
Change-Id: Id7f837cd9e81cd79c4666c98cae84f6cb1a77af0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We must not let ACK timer to run if we have already cancelled it.
So keep track that the timer is cancelled and refuse to run it
if it was indeed cancelled. The reason why the timer might be run
in this case is because the timer might be scheduled to be triggered
after which one cannot cancel it.
Change-Id: I1c8b8cee72bc7a644e02db154d9d009b8d98ade2
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The local port was set to 0 for IPv6 when registering
the connection handler. For IPv4, the code was not setting
the port in local_addr struct.
Change-Id: I82f0c08641a94d75d255ac306eca7bec6c332fba
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Without this info it is a bit difficult to notice what is going
on in loopback case.
Change-Id: I8f61330c01d025e41f00d663bd26947b8cafb5c0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support to print connection handler information in net-shell.
There exists one connection handler for each UDP/TCP port that we
are listening. These prints are only available if CONFIG_NET_DEBUG_CONN
is enabled because the net_context has the same information. Thus the
connection handler info is only printed if debugging is active in order
to verify that handler information is proper.
Change-Id: I0be39a5adb89b2cdbd85524c5d943e4a562b0fde
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If TCP debugging is enabled but if the loglevel is set to lower
than 4, then compiler prints warning about unused flags variable
in net_tcp_trace().
Change-Id: I2e663644b50fe97b75088202e21b286aa010953e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Only 2 attributes lacked this prefix, which makes sense to have, so
applying it accordingly and changing the helpers as well.
Change-Id: I095b2729f977f8fb1624eff8801a4a4e21416693
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Most of these macros are not exactly exposing a buffer, but a specific
header pointer (ipv6, ivp4, ethernet and so on), so it relevant to
rename them accordingly.
Change-Id: I66e32f7c3f2bc75994befb28d823e24299a53f5c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
IPv6 next headers are processed in a way so it is not required to store
which header has been already seen in the net_pkt, as the processing loop
can store internally which one it has seen already.
Change-Id: I266ba8a3a0081a162318cdafb474a0fc44a3185e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is actually useless as there is only 1 RX memory slab, and thus can
be removed to reduce net_pkt structure size.
Change-Id: I62d716515120e7356ee1e2d75bbe1ec32e22c35d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- net_pkt becomes a stand-alone structure with network packet meta
information.
- network packet data is still managed through net_buf, mostly named
'frag'.
- net_pkt memory management is done through k_mem_slab
- function got introduced or relevantly renamed to target eithe net_pkt
or net_buf fragments.
- net_buf's sent_list ends up in net_pkt now, and thus helps to save
memory when TCP is enabled.
Change-Id: Ibd5c17df4f75891dec79db723a4c9fc704eb843d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix warning using incorrect format specifier
Change-Id: Ib6800c40b2cd769612ae6f107e41a941926d8e66
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
We need to check whether buf_sent was true when resending the TCP
segment, and do a buf ref if needed. If this is not done, the buf
will be unref after send, which will cause unpredictable results.
Change-Id: Ibd4490305de88ac6ffd04ec42bba196e57da5c10
Signed-off-by: june li <junelizh@foxmail.com>
While very unlikely it might happen that fragment pointer is NULL
when going through fragment list.
Coverity-CID: 167148
Change-Id: Ic3dbed7ee29c7b864d4830d726f65d7f62dcea84
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If error occurs while preparing response to .well-known/core request,
do not send partly filled payload by simply changing code part only.
It's better to unref the partly filled reponse and prepare a new error
response and send.
Change-Id: I28013a4e331cfc6f01de873e80af48f765e49494
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Commit "net: zoap: Fix memory overflow issue" fixed and implemented
./well-known/core response in a different way, so this api is not needed
anymore.
Change-Id: I8f945fb5842028be50ecfdef95cbe5da3189a538
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If CoAP .well-known/core services list is bigger than single fragment
then current helper functions overwrites beyond fragment space. Which
corrupted whole stack. Right now sending response in multiple fragments
but preferred way is send response in block by block. This should
overcome packet loss across mesh scenarios. Recommended feature will
be supported with later patches.
Change-Id: I30ca55bde2516d80b3583731241ad295799c6614
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Most of the zoap utilities deal with first fragment of buffer chain.
So accessing of buf->frags directly make less usage of stack than
delcaring another variable for frag and its data. Due to code
refactoring couple of lines removed and in between those lines
coverity complained two issues, which is not valid now.
Coverity-CID: 157597
Coverity-CID: 157598
Change-Id: I3035c0625a131d49a4f0250ff0052875d3382544
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When net_ipv6_finalize_raw() inserts RPL(HBH) header after IPv6 header,
it updates IPv6 next header as HBH and HBH next header as original IPv6
next header.
Then net_ipv6_prepare_for_send() will update RPL HBH header if it exists.
But net_rpl_update_header() is comparing HBH option and IPv6 next header,
which is wrong. Wrong comparion does not update RPL instance id and
sender rank. Peer nodes drops all the packets due to invalid instance
ID and sender rank.
Change-Id: I91c1870a09c60f8e1ebc73e434dcc208caf6299a
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Following flow does not work:
net_context_get
net_context_bind
..
..
net_context_put
net_context_get
net_context_bind
At instance of call to net_context_bind, conn_handler
is not NULL and returns with EISCONN.
This patch sets conn_handler to NULL in net_context_unref
Change-Id: I56a50839101b22161644b3cd7c5f510fa1abae3e
Signed-off-by: Mitul Shah <mitul.a.shah@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I8f57a17f78e674aca5400f005db8975c9f9e150e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If there are many connections there may be some delay before an ATT
PDU really gets transmitted over the air. Use the TX callback to
start the response timer so that it doesn't expire too soon.
Change-Id: Ibdd5bc1029ae4034caf329bf03892ac2093a0c67
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to not overload the TX buffer pool and potentially run out of
them, enforce flow control for outgoing ATT packets so that the send
functions block until the PDU has actually been transmitted over the
air.
Change-Id: Ic065bb88aec8c2d0ac2def8ef62131a427f7051f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This CONTAINER_OF() worked by chance, but was actually wrong, since it
makes it look like bt_l2cap_le_chan is the parent container of bt_att.
Instead bt_l2cap_le_chan is simply a member of bt_att, i.e. we can
dereference it directly.
Change-Id: I7307517bae823e54b45db31f75462655ce6eb50d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no command that should take more than a couple of seconds. If
it does there's something severely wrong with the system. Catch such
situations with a clear assert rather than silently blocking the
sending thread.
Change-Id: Ie981fddcc27059df3e4df586e86ceac2e348f509
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
According to the SMP specification the pairing is only to be
considered complete once the last SMP PDU has been transmitted over
the air. Take advantage of the new TX callback to notify completion
only once the packet has really been transmitted.
Change-Id: Ic87e598cd0e040d99f38344b98e476f67e4d9762
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's not valid for a peer to send another request before getting the
response to a previous one, or to send another indication without
getting the confirmation to a previous one. Take advantage of the
recently introduced TX callback to track when it's ok to accept these
ATT PDUs again.
The HCI USB transport has a potential issue here since a race
condition can occur between the ACL data and HCI event endpoints,
leading to dropping data when in fact both peers were behaving
correctly. To avoid hitting this issue, disable the flow enforcement
by default on the qemu targets that commonly use a USB-based
controller on the host OS.
Change-Id: I2791aaec6f6c0f8fd78a9a809a25e3ce129106c7
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Protocols/profiles may want to know when exactly their PDU has been
transmitted over the air. To make this possible, introduce support for
a callback that will get called when the controller reports that a
packet has been transmitted (through the Number of Completed Packets
HCI event).
Change-Id: Ia3a19b93c5b2111f144bfabe5861187c41525f30
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the ECC code was last time refactored hci_raw.c was forgotten
about. This fixes the issue so that ECC works again with hci_raw.
Change-Id: I1b1df66f1b2a311db611b9936ec074c88caf4143
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This reduces the pressure on TX pool which may constantly block in case
of heavy traffic causing the RX thread to block as well.
Change-Id: Icfdde32031715e882085b7fa371191f157954156
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds net_buf_reset which can be used to reset the state of a buffer.
Change-Id: I4b7c89dfd1a23a2ec8dfa3c99d5b02b9bcbceef3
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes the code attempt to allocate from the original buffer pool
before relying on le_data_pool which shall only be used as last resort
as it is configure with minimal possible buffers (1 per connection).
Change-Id: I85b581627f5c3b1bf1ee7c5fa69099c5aca13d4a
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Added support in the Controller for increased feature set
bit fields in Bluetooth 5.0. Cached feature set in the
connection context is increased to a uint32_t value to
accommodate 17 feature bits.
Change-id: I9ae15d6d90fa7a3de186905d3c68088ee22d2911
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
With the introduction of event mask implementation in the
Controller, it is discovered that peer centrals
initiating LE connection parameter requests timed out as
the Host did not get/enable the HCI LE connection parameter
request event in the set LE event mask command.
Fix by adding the LE connection parameter request event bit
mask while creating set LE event mask command.
Jira: ZEP-2027
Change-id: Ida7750f375addc8a91036fffc47325518a3d2ec0
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To avoid having to define a BIT64() macro in a public namespace, use
instead masks directly instead of bits, and also refactor the host code
so that it uses those instead of the earlier byte array with hardcoded
indices and masks.
Change-id: Ief03db616a96df65349d24289b62566a268ffdd0
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Rename symbol names with channel/chnl to chan.
Change-id: I196ffea79e7e10b0253363949051fdf82be62cb4
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Since the type of int, uint32_t, etc change with newlib we get the
following error:
subsys/bluetooth/host/at.c: In function ‘cme_handle’:
subsys/bluetooth/host/at.c:272:25: error: passing argument 2 of ‘at_get_number’ from incompatible pointer type [-Werror=incompatible-pointer-types]
if (!at_get_number(at, &val) && val <= CME_ERROR_NETWORK_NOT_ALLOWED) {
^
subsys/bluetooth/host/at.c:46:5: note: expected ‘uint32_t * {aka long unsigned int *}’ but argument is of type ‘int *’
int at_get_number(struct at_client *at, uint32_t *val)
^~~~~~~~~~~~~
We we can easily address by making val a uint32_t.
Change-Id: Ie6988368bd862afd4075baede7cb0a66c1628c18
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If we use newlib the isdigit (and other similar functions) return an
error as char can possibly be viewed as signed:
usr/include/ctype.h:57:54: error: array subscript has type ‘char’ [-Werror=char-subscripts]
#define __ctype_lookup(__c) ((__ctype_ptr__+sizeof(""[__c]))[(int)(__c)])
Being explicit about the char being unsigned char deals with this.
Change-Id: I348189e1df11a1fcc58e5810b010b602fd2df33e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For consistency, "chan" and "param" are used wherever "channel" and
"parameters" are the words in the specification.
Change-Id: I778a8501ae6af991618c14cc6e395d765a9ae102
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix doxygen comment typos used to generate API docs
Change-Id: I3efff6f5fa26f87d1e658d6336fef01ce45f5bb0
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Use UNALIGNED_GET and UNALIGNED_PUT throughout the networking stack to
access fields from the IP address structure. These structures can be
mapped directly to buffers and the macros are required for correct
unaligned memory access.
Jira: ZEP-2012
Change-Id: I55f9da7b143a22fa869d5d215c661de988cd9b91
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
This can be useful to override the default value, for testing.
Change-Id: I23b559152c71955ff5aa6fd3643f1f40f5594194
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This permits to tweak the TX power in dbm.
Change-Id: Idadff397941a39010ce3c374d9ca74b777934626
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This does not save any space but sets the fields in the
structs in more natural order. Move IPv6 related
fields in net_if into internal ipv6 struct so that all
IPv6 fields are located inside one struct. Same thing
is done for IPv4 fields which are now located inside
IPv4 internal struct in net_if.
There is no functionality changes by this commit.
Change-Id: I7d72ec0a28e2b88c79a4c294655d5ef6da6ccb25
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
So manipulating it requires to be ready to swap it if the CPU is BE.
Change-Id: I8d657c31cecfc9f3fcd010efbb6d090bf021f5f5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
DNS resolving is better done with DNS resolve API so remove
the DNS client API which is quite hard to use.
Change-Id: Ide4973a5be674414ea6e04a35c938195cce40b6a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need a way to know when IPv6 address is successfully set
into network interface.
If IPv6 DAD (Duplicate Address Detection) succeeds or fails,
we send a management event for that. This can be used by
other components to detect when the network interface is in
usable state.
Change-Id: Ifb22415fe21f31f5dba4f55455d6e0f89b414d32
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some of the IPv6 utility functions were missing const in
one of the parameters that are not modified by the corresponding
function.
Change-Id: Ic9fe53daac288570c14423fd9410dcf15d1c5cfa
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This makes net_ipv6_nbr_add able to update entries so it can be reused
when receiving RA or NS requests, so it now performs a lookup before
creating a new entry (using nbr_new to reuse more code) and in case it
finds a match attempts to update the lladdr.
Change-Id: I305a67a955e037cbbb862fef947a5fcfe131507c
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
net_ipv6_nbr_add shall init the delayed work as nbr_new does, so this
unifies both codes into nbr_init which does take care of initializing
the fields properly.
Change-Id: I91746276d346a3dc3c36be20d49bcf1968245fc5
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Route lifetime was printed using wrong modifier.
Change-Id: Ib503d50b5817491984d51bbdaadf7457fdde178b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure the RPL is compiled ok if CONFIG_NET_RPL_MRHOF is
enabled in the configuration.
Change-Id: I51fc0e20f854164c7e0374fa6a1ebf1d4e4dbc5b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If multicast routing is set meaning that MOP3 (Mode of Operation)
is enabled, then the code was not compiling properly.
Change-Id: Ice8a9f7b705c781536d3c2c5ca6cc2bb77a7acc1
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print information about configured DNS servers when starting
in order to ease the debugging.
Change-Id: I3ba71e514e463db790b82913e4c66a67160366dc
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need to set the resolved IP address family and length
before calling the user callback so that callback does not
need to figure out these values itself.
Change-Id: I724909fc1707608ab8728231a0311795b6a313f3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The default hop limit is defined in struct net_if. It is possible
that user might want to tweak it for each network packet. For this
purpose, a net_nbuf_set_ipv6_hop_limit(buf) function is created.
Change-Id: I7568330358f80f0f5007d6d3c411c120b043c04f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The Kconfig.rpl file was missing option to actually collect
RPL statistics. Unified the config option name to be
CONFIG_NET_STATISTICS_RPL as there was two conflicting settings
in the code and both of them were missing from Kconfig file.
Change-Id: I4ce4fcbaa317b36cac315ea3b3f710fa7a344b25
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The probing_timer is only available if CONFIG_NET_RPL_PROBING
is defined.
Change-Id: I2835d17e6c3d616f815f8beefd87d2571a5ad94c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
After failing to send the buf we need to release it.
This is not done for Bluetooth or IEEE 802.15.4 links which
create a copy of the sent buf and the failure case is already
checked by net_tcp_send_buf().
Change-Id: Ia556376b58ad74f68accb64eb2221a78d59dc2ec
Signed-off-by: june li <junelizh@foxmail.com>
In case CONFIG_NET_BUF_POOL_USAGE is defined use print pool->name
instead of the pointer.
Change-Id: I0be5fd8283a887145e61bdad02f721265453ce20
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use UNALIGNED_GET in net_addr_ntop as the uint16_t pointer used in this
function can point to an unalined address.
Jira: ZEP-2012
Change-Id: Idfbfa8da4c8d4e10299c4ae4d6431b10466cc988
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
If the IPv6 fragmentation support is enabled, then print current
status of the IPv6 packet reassembly in "net conn" command.
Change-Id: I384e35928b67dd39ac720c77683b1767e2a1ce88
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Figure out what is the last extension header in IPv6 packet
and return offset to it. This is needed by IPv6 fragmentation
when fragmentation header is added to the packet.
Change-Id: I925ab806a5de076a425ff354711730d4f4b3c52f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds support for IPv6 packet fragmentation when
receiving (IPv6 reassembly) and when sending larger than 1280 bytes
long IPv6 packet. See RFC 2460 chapter 4.5 for more details.
Jira: ZEP-1718
Change-Id: Ia31c147cce4d456ee48f39276cca99aa09ce81d6
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add net_nbuf_split() function that can be used to split
an existing net_buf fragment into two arbitrary length pieces,
and return the two new fragments to the caller. The data from
the original fragment is copied into these two new fragments.
Existing fragment is not modified.
Change-Id: I463e675232c6e19c2a42929f480893a6d1265873
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Do not try to cancel query if the DNS query index is < 0.
Coverity-CID: 166770
Change-Id: I03c1f274453640d0ff80694628b8e8f18e8de900
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use UNALIGNED_PUT() to store the MSS value into network packet
because the memory location cannot be guaranteed to be properly
aligned.
Change-Id: I77fd7a70ef45eedb657cac29457b0239b0a1d4c2
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
CONFIG_* usually come from Kconfig, rename variables that are locally
defined to avoid confusion about where they are set.
Change-Id: I402713e6f852907e75be4bc2b916a7d15dd5649c
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This fixes regression introduced by
87f2f7afec.
Change-Id: I4a1177ad42c7bb20fe66f8927cd00a30236152af
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the connection process fails the user may still need to do
bt_conn_get_info() in its connected callback, so this needs to give a
meaningful value for the remote address. Start off with the one that
was given to bt_conn_create_le().
Jira: ZEP-2005
Change-Id: I4e9a033dec7c55fa549f5b6746c3bd81c0ccade5
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This replaces custom made list manipulation with sys_slist_t which makes
the code more readable.
Change-Id: I9ee024ad83da3e28f2ecab74b001bf0e795fe489
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use #if defined(...) constructs while using conditional
compilations of advanced event preparation and advanced
scheduling implementations.
Change-id: I728c76d0e7dbbfa378e8978b726ec404d9e55a72
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Move the scan duplicate filter length option and group it along
with rx/tx buffer size Kconfig options.
Change-id: I3df07e667029c7d2571270db442ecb7241a417c2
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The bt_conn_set_state() function will not notify the connected
callback of the connection error if conn->err isn't properly set.
Jira: ZEP-2005
Change-Id: Idc30e736f4d8ba00156bf5c0e37dcccdb151742f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
CONFIG_DEBUG_INFO was disabled for IAMCU targets. As per Jira update forked
arch/code is gone. So it should not block enabling DEBUG_INFO for IAMCU.
Currently CONFIG_DEBUG_INFO depends on (x86 = y && !X86_IAMCU)
CONFIG_DEBUG_INFO can not be set for IAMCU. this patch removes dependency.
Jira: ZEP-601
Change-Id: Ib5635096f83f7b931c277b667a55c6d54f8e946a
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Conditionally declare the iterator variable to avoid a warning when
compiling the controller without any duplicate filter entries.
Change-Id: I69e23d4c594db18172dc57d45e7925243fe2da69
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The main issue is that after the latest update to TinyCrypt the
ecc_make_key() API expects a twice as big random number. Fix this, but
also move the variables to the static context since we're limiting one
HCI command at a time. Also place the variables in a union based on
their temporal dependencies. Thanks to this, we can now further reduce
the ECC stack size by 40 bytes (on ARM this then reports 12 bytes of
unused stack after key-pair generation and DHKey calculation).
Change-Id: I1036e0ca15f7c08063cba9e568d7df99e65c9156
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
HCI event masking allows the host to choose which events are reported to
it to avoid interruption and excessive traffic. This patch implements
masking to drop any non-enabled events as specified by the host.
Jira: ZEP-1769
Change-Id: If09d4aa22b0da8f743fc42a3b0db3f369daaff96
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the controller's ability to drop duplicate advertising reports
when instructed by the Host.
Jira: ZEP-1246
Change-Id: I2d1b7abf1ed950dde705e5df30a858c595f3834c
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add Controller advanced Kconfig options to select IRQ
priorities of the Radio, Ticker's Worker and JOB IRQs.
This will provide an opportunity to have peripheral IRQ's
of higher level than Bluetooth Controller.
Change-id: Iaa128c1cd64a309a77d42d485fdefe68f31e4895
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Move the nRF5 specific GPIO debug pin macro definitions to
hal/nrf5/debug.h.
The Controller's hal folder contains prototypes and
hal/<soc> shall contain SoC specific implementation to
realize a software-based Link Layer.
Change-id: Ic7bf283f926bbc3069e7d15c047fe93a6daa894f
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Cleanup redundant ticker busy loop that could hang if the
worker and job IRQ priority levels are misconfigured, and
job gets disabled before all users/mayfly functions using
job complete.
Change-id: I053ad75a4328c51cfe651b820a2fa961e42ae48f
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
In a host plus controller combined build, if no connection
is required, deselect CONFIG_BLUETOOTH_MAX_CONN. This will
reduce RAM and ROM usage in the controller.
Also, make BLUETOOTH_PERIPHERAL, BLUETOOTH_CENTRAL and
BLUETOOTH_CONN switches accessible by the controller kconfig
to select the right roles to enable.
Change-id: I164cf696ab2a6f4859086d2cb18f6d3f2b1399d3
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
BR/EDR sources that was compiled under BLUETOOTH_CONN
if-clause is moved out as independent conditional
compilation based on selected BR/EDR feature support.
Change-id: Iedfafc6056132654a9150ed235b245f8be62b4b1
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
If during hfp_hf_send response callback is not filled with NULL
and you receive unsolicited callback. which will not be taken care.
This patch fixes this issue.
Change-Id: I04007059d62273b9cdddf29e2d4a9086b07a01e5
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
A initiation to send AT commands is given in the application
with prefered AT command as the argument.
This patch supports to send the command within the profile stack.
Change-Id: Id5caa3ce64070fc17e60f4ea61a8c83a961099ba
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
This cause packets that are up to 2 bytes off segment maximum length
to be considered transmitted when in fact that could be some bytes left
to be transmitted which cause any subsequent packet to trigger invalid
SDU on the remote end:
[ 3612.376068] l2cap_le_data_rcv:6757: SDU fragment. chan->sdu->len 66 skb->len 68 chan->sdu_len 67
[ 3612.376073] Bluetooth: Too much LE L2CAP data received
Change-Id: Id2f3469ce1c0b27bb87c4d5bc18e6ede9d93dbde
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Move the Kconfig option BLUETOOTH_MAX_SCO_CONN to BR/EDR if
clause.
Change-id: Iead2bc5a70a9499125f9edf22e85ade4dda8f5ac
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Move the BLUETOOTH_UART_TO_HOST_DEV_NAME options to after
BLUETOOTH_HCI_RAW option to group it together in the
Kconfig while using menuconfig.
Change-id: I21da080a5ffa30a08b1a1aa148ce8116e63a3c18
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Group the stack size related options together to represent a
better order when using menuconfig.
Change-id: Id2968607e5054e30029c42987b3e70cb8cbfc74d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Move the Kconfig BLUETOOTH_CONTROLLER switch from top-level
Bluetooth Kconfig to Bluetooth Controller Kconfig.
Change-id: Iead760c22a0fbbda11e4558c4943b3366ecc8769
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
This makes the code consistent with respect of errors, so instead of
checking directly on bt_gatt_write_without_response let this up to
bt_smp_sign.
Change-Id: Iea8d0bd2020df427b7542e2878ce8d9fd8b94170
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When there's no support for connections there's also no need to track
the controller side buffers.
Change-Id: I7eac3af486f139f1ab32efda8ccfa188ed8359eb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Checking both if signing has been requested _and_ conn->encrypt can
bypass signing leading to the caller to assume that a proper signature
was send in when fact it was not.
To fix now the code explicitly checks if SMP is enabled and in case it
is and signing was requested fails.
Change-Id: Ie17df4a4c2191f2da0172c687db7999395839a97
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In case the controller is receiving PDUs very rapidly, prevent it from
spamming the logs by limiting its stack analysis to at most once every
5 seconds.
Change-Id: I31c70d28e8af62b27172a4a77bf6e614ea3e20eb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move company id and subversion number Kconfig to the
Controller configuration section from the features section.
Change-id: Ic4deb8b24d84d9b1817ba542705eebd612f0e020
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Added a explicit Kconfig option to show the Controller's
advanced feature configurations. These feature
configurations need specific in-depth Controller
implementation knowledge and should not overwhelm normal
users of the Controller.
Change-id: Iae764f2b266b199cf180936c51c7a4ea089ee510
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig option to enable advanced scheduling in the
controller.
Enable non-overlapping placement of observer, initiator and
master roles in timespace. Uses window offset in connection
updates and uses connection parameter request in slave role
to negotiate non-overlapping placement with active master
roles to avoid slave roles drifting into active master
roles in the local controller.
This feature maximizes the average data transmission amongst
active concurrent master and slave connections while other
observer, initiator, master or slave roles are active in the
local controller.
Disabling this feature will lead to overlapping role in
timespace leading to skipped events amongst active roles.
Change-id: I16e4e6c3ca99f93987ab86924af0cb9d76bdbc7e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
HCI drivers are obliged to send HCI Command Status/Complete events
from a separate context than all other data, however the ECC wrapper
was violating this rule (sending everything from the same ECC thread).
This could lead to a deadlock if e.g. the ECC API user decides to
generate a DHKey from the same callback that it got notified of local
key-pair generation.
The obvious solution is to emit the Command Status directly from the
send function, before passing the command to be processed by the ECC
therad (through a k_fifo). However, this is not quite so simple since
bt_buf_get_cmd_complete() reuses the original command buffer, meaning
we'd loose the original parameters after sending a Command Status.
To work around this limitation with bt_buf_get_cmd_complete() we stop
passing the command buffer to the thread and instead store the
parameters in static variables and do the thread communication using
flags and a semaphore. One side effect is that only one command can be
pending at a time, however that works out fine for all of the users of
ECC.
A nice side effect of moving some things to static variables is that
we end up reducing call stack usage in the ECC thread, allowing it to
be shrunk by 180 bytes (verified to be sufficient for both ARM and
x86 boards).
Change-Id: Ic41f0316d3fe4d14b64fd3d0a549b221d168411a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Added Kconfig option to enable advanced event preparation
feature.
Enables advanced event preparation offset ahead of radio
tx/rx, taking into account predictive processing time
requirements in preparation to the event, like control
procedure handling and CPU execution speeds. Crystal
oscillator is retained between closely spaced consecutive
radio events to reduce the overall number of crystal
settling current consumptions.
This feature maximizes radio utilization in an average role
event timeslice when they are closely spaced by using a
reduced offset between preparation and radio event.
By disabling this feature, the controller will use a
constant offset between the preparation and radio event. The
controller will toggle crystal oscillator between two
closely spaced radio events leading to higher average
current due to increased number of crystal settling current
consumptions.
Change-id: I19e640f7395ac7938873ef4bfac38acf8d6f7e0e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The monitor protocol provides support for logging packet drops with
the help of the extended monitor header. Implement support for this.
Change-Id: I7ef7894816cb8d1bd876842d0253ef0980471e69
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The IRQ lock should never be held for long periods of time. Instead of
using the IRQ lock to prevent monitor protocol corruption simply drop
the data. Follow-up patches will add additional drop count tracking so
that these get reported properly over the protocol.
Change-Id: If498125b29f1b58bed676c78ad2062e2aa206318
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Using lookup table to search for unsolicted command and its
handler function.
Change-Id: Id677dad3918d7187e0065ada2985ec12a97f8ed9
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
This helps debugging as printable string of the ICMPv6 type is
printed when packet is received if debugging is active.
Change-Id: I22b84bb6b28db7fba030699af3e561a0775b53d2
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It requires a net_nbuf, so the actual buf, and not a frag here.
Change-Id: I4fd888c9a91f5e3f3dd664ae5e3bf93f90a2f597
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will refactor net_core.c and move IPv4 specific code
into ipv4.c which is a more logical place for it.
Change-Id: Ia60c5bfec488d2d1a664f113dc3df88e7d5badd1
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This will refactor net_core.c and move IPv6 specific code
into ipv6.c which is a more logical place for it.
Change-Id: I5bbecbb760111326b9a6bbef5802c53d7f6efda9
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
DROP is only on error case, here it should return NET_OK if it was a
proper ARP packet and it got properly handled.
Change-Id: If347e80a76b3a56a9455b70d11b735c1fd910117
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The context buffer pool was introduced to deal with TCP holding buffers
when 6LO may modify them, therefore it makes sense to have it enabled
by default when TCP and 6LO are enabled given that the code can deal
with NULL pool in case the application don't implement one.
Change-Id: I600ca31ab40c96ee27937c2e885e332b0cee4995
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CONFIG_NET_BUF_WARN_ALLOC_INTERVAL can be used to configure the interval
used to print allocation warnings.
Change-Id: I914f2e0d43b3f00c201e49ff42a45fa950b2df94
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Shell crashes if you try to retrieve IPv6 nbr reachable time
when CONFIG_NET_IPV6_ND is disabled.
Change-Id: I3c5b3b5614abf80373b892943fa1ab936d235f3c
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Return proper verdict on handling of DIS messages. Otherwise debug
prints will be confusing that packet dropped.
Change-Id: Ia4e18d6238868e3aed4b17e2c9ea11aa432869be
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
No functionality changes, just refactored few rpl functions to
to align nicely.
Change-Id: I05c0397de7a8392cc781de2747802b2dd1bb8146
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Don't assume NULL returns are always errors.
Change-Id: I28d7a0fa6c848e338635010b1fdc9fc3e8440b27
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This might indicate buffer leaks or deadlock is happening.
Change-Id: If91a65ccfe1be9497b210de21e80b533b6739367
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Following changes are made:
1. Output using NET_INFO logging level. This function is not part of
automatic logging, and must be called explicitly by a user application.
But if it outputs using NET_DEBUG, then DEBUG level needs to be
enabled, and the output of this function will be drowned in logging
spam. So, let user to enable just INFO level.
2. Show entire structure of the fragment chain, *including* the head
net_buf which holds net_nbuf structure. It is numbered as -1 in the
output to preserve existing order (and not change existing size
calculations).
3. Show owning pool (and its properties, like buffer size/user_data
size) for each buffer.
4. Check for NULL pointer, e.g. for convenience of calling directly
from net_context receive callback (which will be called with NULL
on TCP peer closed connection event).
With these changes, a newcomer from one look at the output of this
function will be able to have a clear basic picture of network
buffer management in Zephyr, and recurring user will be able to
recall any details at once.
Change-Id: I8f9562748329d749f765cc6af7989a448256d7e0
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
No functionality changes, just refactored net_rpl_update_header
function to align nicely.
Change-Id: I5b3e099593bb964245ca06c9fb2ec85859a0640c
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Search destination address in IPv6 neighbor table. If it doesn't
exist in IPv6 neighbor table then go for routing. Added sanitycheck
to verify destination ll address is not the source ll address of
original packet (that means we are re-routing back to original sender).
Change-Id: I24adace6a0d17fbd1d2a36a5d75c79320de0a883
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
net_ipv6_nbr_lookup_by_index() will always find first matching entry
in IPv6 nbr table with lladdr index. But there can be multiple neighbors
linked to same lladdr index. So find route nexthop with ipv6_nbr_data
from nbr(ipv6 nbr) data pointer.
Change-Id: I5081d40330f5bc1ef0d96def03f4add4808b2fe9
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Router lifetime timer initialized in router_init but not submitted.
Change-Id: If5a77f413832db52eff99e7191f82d2a8fc8f081
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Extra data size was not considered in nbr size calculation.
Change-Id: Idc572abf55c8f9fd19940edb719f58e02e7f8ecd
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Route lookup is necessary only if life time is
NET_RPL_ZERO_LIFETIME, otherwise lookup not required.
Change-Id: I25fb85c53e2d43cfdce08411af385f3ae26384cc
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If DAO message is routed through different nodes or sent directly
to a parent and ACK lost somewhere in noicy network. Node can not
join RPL mesh network properly. So try re-sending DAO message for
max number of trials (Kconfigurable).
Change-Id: I7f6a065deacd1e3942c89118ce8da4fbaa34af51
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When sending TCP data, check if the retry timer needs
to be started.
Change-Id: Iea90716e918dec0b22e60bf32467b11c0d1a296f
Signed-off-by: june li <junelizh@foxmail.com>
k_sem_take() is documented as returning negative value for error and
0 for success. The old code didn't work.
Change-Id: I717b35d73fced476b50e3207410858f86c2ef9bc
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This reverts commit 4e2eaec268.
It's invalid to call k_yield from ISR. In fact, it'll trigger an
__ASSERT.
Change-Id: Icc7b81c07c2e7df63fe7d5029fac446ac6fe508b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If this is not done, there is common pattern that on big input block
(e.g. from a clipboard paste), IRQ routine is called in a tight loop,
leading to circular buffer overflow.
Change-Id: I69a7aa78081b8d74652406f3b3a577ddaf4c5f6f
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This change introduces console_getchar() and console_getline() API
calls which can be used to get pending console input (either one
char or whole line), or block waiting for one. In this regard, they
are similar to well-known ANSI C function getchar/gets/fgets, and
are intended to ease porting of existing applications to Zephyr, and
indeed, these functions (shaped as an external module) are already
used by few applications.
The implementation of the functions is structured as a new "console"
subsystem. The intention is that further generic console code may be
pulled there instead of being in drivers/console/. Besides the
functions themselves, initialization code and sample applications
are included.
At this time, there're may limitations of how these functions can
be used. For example, console_getchar() and console_getline() are
mutually exclusive, and both are incompatible with callback
(push-style) console API (and e.g. with console shell subsystem
which uses this API). Again, the intention is to make a first step
towards refactoring console subsystem to allow more flexible
real-world usage, better reusability and composability.
Change-Id: I3f4015bb5b26e0656f82f428b11ba30e980d25a0
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
It needs to check if current event matches:
- cb's layer
- cb's layer code
- cb's command
If none match, it will not raise the event.
Fixing the unit test as layer must be always != 0.
Jira: ZEP-1940
Change-Id: Iadd63e751fa6e534a10e7da9cae0f5bb5a384461
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Most (if not all) 802.15.4 devices can handle ACK replies by
themselves.
Change-Id: I0319d59de767b20eb67c1592bacaa4a7b7015cad
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that interface is not directly used in data and mac frame creation,
let's just pass context pointer.
Change-Id: If002e6790d044eeffc57cb5685ac9525fbd6e43c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that RFD is default, the extended address can be changed through net
mgmt API, and thus no longer be the same as device's generated mac address.
Change-Id: I07ee647615c2caa1994712147c6c8a2b4306900d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There is no need of interface anymore.
After previous changes, it appears that net_if parameter is not used so
we can remove it.
Change-Id: Id3570f50865696818a9be2280172e2e25fc537f7
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
commit id 7a11439020 changed this.
Hopefully that changed did not affect anything.
Reducing minimal frame length and applying the change everywhere where
relevant.
Change-Id: I5ae203751bfcf70cef833620106d2c2d0e33b7a5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
And use them accordingly in the common code part.
Change-Id: Id91b76e5baea607c0d68eebcde6f84e4e35ca44c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
ORFD was a hack, from the beginning of the IEEE 802.15.4 Soft MAC stack,
but is now useless and can therefore be removed.
Change-Id: I74d5e1995993f4a0749b6d9d553406d5ae162bda
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In order to simplify when 802.15.4 is selected on these samples, let's
setup the device through a common code.
For this to work, RFD is now the default.
Change-Id: I46590864442f77d83f681cc0e854c94344648856
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It's more readable and along with other part of the system.
Change-Id: Ib4be787d74310d838f38b1f1d5624e7357da8969
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These should be used by samples to fix basic 15.4 settings.
Change-Id: I31ad1540008ac760b7aef720e520bf8e72d3a805
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
s/SAMPLES/APP for name shortening. Applying the change where relevant.
Not only IP addresse will be available as samples settings there but
also IEEE 802.15.4 channel, pan_id, and more for instance.
Change-Id: I05dd24989bd0c804d9588092d67044a3e063bc88
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will be needed for Thread/MLE.
Change-Id: Ib421da66cfc4da8111ff131f08cac74a11674928
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These requests are used to set/get the key, the mode and the level of
the IEEE 802.15.4 link layer security.
Only implicit key mode is supported for now.
Change-Id: Ifbc9a5d08f9fbf0d51d6c3e4b650cfdce3d263db
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Initialize the ciphers.
Once the header is parsed and validated, we get all the necessary info
to decrypt the frame properly.
Change-Id: I3142fa572c7566b40efe18cf9d4e3f2b4bce0612
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It's not only about decrypting and authentifying but also setting the
right frag's length after that.
Change-Id: Ifc766b212b37d4e3593c210f6646ee85dff2ab6d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Take into account the current security context to compute the header
size.
Provide the function to fill-in the aux security header in a frame.
Finally, call the generic encryption function which will process the
frame relevantly according to the given security context.
For now, only implicit key mode is supported.
Change-Id: I5412c32179e70217c0946b1b54d9a752375d522f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This provides the means to authentify with/without encryption or
decryption of a frame following a generic 15.4 security context.
Change-Id: Ia5dbb7f43936a8131112fe4b16c9780e30f904c1
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
