Create support for registering a callback that will be called
if the device leaves or joins IPv6 multicast group.
Jira: ZEP-1673
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Commit cd35742a2 missed one unref too many on pending packet which was
triggering a crash which commit 0b8434f08 tried to fix, but it generates
a leak when there is not pending entries left in arp core. Finally,
fixing what cd35742a2 should have done: removing the extra unecessary
unref after sending the pending packet.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Errors has been ignored when using TLV writer to create/write object
instance/resources. Modify to propagate the error back to the caller.
To reproduce the issue, try to create IPSO light control object
instances twice. Since the default instance count is 1, the second one
should be rejected and responded w/ error. But the current
implementation will respond w/ 2.04.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
We did not check the requested object/object instance/resource exists or
not before we adding an observer. Correct it by checking the existence
first.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
We should stop sending out notification to the peer when the
object/object instances requested to be observed is removed
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
We were using sys_slist_remove() to remove object, object instance and
observer w/o passing the previous sys_snode_t to it (NULL).
This will instruct the function to treat the node as the list head and
result in unexpected behavior after the removal.
Correct it by using sys_slist_find_and_remove() or passing the previous
node to the function.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
When a request demands to create a new object instance, it will search
whether the request object instance exists or not. However, current
implementation does not reset the lwm2m_engine_obj_inst at the time it
is deleted. It only removes the object instance from the sys list.
Correct the behavior by resetting both object instance and resource
instances at the time it's deleted. Also, consolidate function
lwm2m_delete_handler() and lwm2m_delete_obj_inst().
To reproduce the issue, try to create light control object instance
(/3301), delete the created instance and create it again. You shall find
following error message dumped.
> [ipso_light_control] [ERR] light_control_create: Can not create
instance - already existing: 0
> [lib/lwm2m_engine] [ERR] lwm2m_create_obj_inst: unable to create obj -
3311 instance 0
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
If the packet is put pending because ARP request need to be
done, then do not unref original packet.
Fixes#1416
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add a command "net arp" to net-shell. This new command will
print ARP cache contents if IPv4 and Ethernet are enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit 725be227 ("net/mgmt/event: Commands must be > 0 so
masking them works") prevented IPv6 address setting when an
application was initialized. The check in subsys/net/lib/app/init.c
needs to be adjusted because of that change.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There were bunch of config options in tests/net, net-shell and
wpan_serial sample, and those options had wrong name so they
were ignored by the code.
Fixes#1428
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When new connection is accepted, the TCP context variables like
sequence number etc. were not properly set.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For IPv6 check_ip_addr in subsys/net/ip/net_core.c makes a
NET_DBG call to report when a net_pkt is missing a destination
address. An analogous NET_DBG call has been added to the IPv4
destination address checking.
Signed-off-by: John Andersen <john.s.andersen@intel.com>
prepare_arp() was unreferencing original pkt (called pending there) in
case of error.
net_prepare_arp() was always unreferencing pkt, though it could have
been already unreferenced by prepare_arp() as seen previously which is
an extra bogus unref in this case.
And in case it returned NULL, ethernet_send() would return NET_DROP
which in turn would make net_if's tx code to unref again the pkt.
This patch ensures pkt is unrefed only once and at the right place.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The TCP state string is only printed if CONFIG_NET_DEBUG_TCP is
defined. If that is not the case, then the "net conn" command
should not print the "State" column name as the state will not
be printed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This reverts commit 817245c564.
In certain cases the peer seems to discard the FIN packet we are
sending, which means that the TCP stream is not closed properly.
This needs more work so revert this for time being.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When new socket context is created on accepting connection to a
listening socket, its recv_q FIFO should be initialized. Without
initialization, this worked by a chance when FIFO structure was
simple, but recent change to add dlist to it (which now needs
proper initialization) exposed this issue.
Jira: ZEP-2576
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If the query name is already in numeric format, there is no
need to send the query string to DNS server as we can just
convert it ourselves.
Jira: ZEP-2562
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit removes IP address parsing from DNS init and
replaces it by call to net_ipaddr_parse().
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_ipaddr_parse() will take a string with optional port
number and convert its information into struct sockaddr.
The format of the IP string can be:
192.0.2.1:80
192.0.2.42
[2001:db8::1]:8080
[2001:db8::2]
2001:db::42
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If network context is closed, send FIN by placing it to the end
of send queue instead of sending it immediately. This way all
pending data is sent before the connection is closed.
Jira: ZEP-1853
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
TLS and DTLS are not related to each other so allow DTLS to be
enabled even if TLS is disabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The "net app" command was accessing NULL pointer if TLS and UDP were
enabled but DTLS was not.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Earlier we modified the original pkt chain when creating IPv6
fragments. This is not a proper way as the original chain might
still be used in TCP when re-sending a message. So when fragmenting
the packet, clone it first and leave original packet intact. This
occupies litle more memory but is now safe.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is very unlikely to happen but the device will access null
pointer if we do not properly check the return value of header
check function.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When trying to figure out where ICMP / TCP / UDP header is located
in net_buf, print more information about what we were doing if the
header cannot fit the first fragment. This is much needed infomation
in debugging weird issues.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Using memcpy() to copy net_pkt is not safe because there are
pointers inside. So use the new net_pkt_clone() to do that.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is needed when one wants to copy the whole fragment chain
and its head pointer net_pkt.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IP header was stripped by _net_app_ssl_mux() when it received
IP packet. This is fine but if the application expects the get
the IP header, then there is a problem. Fix this by saving IP
header to ssl_context and then putting it back in front of the
packet when the data is passed to application.
Note that this IP header is not used by net_app when the packet
is sent because TLS/DTLS creates a tunnel for transferring packets
and user can only sent packets via this tunnel.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
k_delayed_work_cancel now only fail if it hasn't been submitted which
means it is not in use anyway so it safe to reset its data regardless
of its return.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The original commit 8ebaf29927 ("net: http: dont timeout
on HTTP requests w/o body") was intended to handle a case
where an HTTP response had been retrieved from the server but
the HTTP parser couldn't meet the criteria for calling
"on_message_complete". For example, a POST to a REST API
where the server doesn't return anything but an HTTP
status code.
It was a really bad idea to check a semaphore count. There
is a lot of kernel logic built into semaphores and how the
count is adjusted. The assumption that the value is 0
after the k_sem_give() is incorrect. It's STILL 0 if
something is pending with a k_sem_take(). By the time
k_sem_give() is done executing the other thread has now
been kicked and the count is back to 0.
This caused the original check to always pass and in turn
breakage was noticed in the http_client sample.
Let's do this the right way by setting a flag when
on_message_complete is called and if that flag is not set
by the time we reach recv_cb, let's give back the semaphore
to avoid a timeout.
Jira: ZEP-2561
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The HTTP header field pointers are saved for each HTTP request.
But the counter that saves the pointers was never reset to initial
value when the connection was dropped. This meant that the header
field values were only proper for first HTTP request.
Jira: ZEP-2463
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The server needs global enable/disable status instead of only being
able to enable or disable just the TLS server part.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we have specified AF_UNSPEC when initializing application
server local address, then we try to bind to both IPv4 and IPv6
addresses. The old code did not honor the port number in this
case but used some random value for port.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user has specified a specific local address, then honor that
and do not try to bind IPv4 context if only IPv6 is defined,
and vice versa for IPv6.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Zeroing-out all bytes from a connection structure when it's
unregistered ensures all state from a previous connection is gone and
can't be mistakenly reused.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
If either a remote or a local address were supplied to the
net_conn_register() function, the IP stack would proceed to copy
sizeof(struct sockaddr) bytes from the respective remote_addr
or local_addr pointers, regardless of the actual size of the storage
these pointers point to.
Use the proper size depending on the socket address family.
Coverity-ID: 173630
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
If CONFIG_NET_DEBUG_APP was defined, but neither NET_APP_SERVER nor
NET_APP_CLIENT, build failed due to net_app_cb() haven't beeen
defined. So, define it to empty in this case.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Setting just IPv4 address as was allowed before isn't enough for
real-world usage (e.g. accessing DNS and outside servers in general).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Per LwM2M spec (7.3.2.4 Operation on Object):
"If the payload (New Value) conveys an Object Instance ID in conflict
with one already present in the LwM2M Client, the complete request
MUST be rejected and a "Bad Request" error code MUST be sent back."
Let's do that.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Per LwM2M specification 7.3.2.4, "Optional Resources MAY be conveyed
in the "New Value" parameter as well; the LwM2M Client MAY ignore the
optional resources it doesn't support."
Update TLV/JSON writer to ignore error when object fields are not
found (treated as optional resource). This will allow the resources
supported being written.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: re-worked patch post addition of CREATE
operation.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Prior to this patch, a CREATE operation was handled as a WRITE operation
after the object instance was created. This becomes problematic when
handling of optional resources differs between these 2 operations.
Let's introduce an actual CREATE operation and use it later to create
these differences.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
We are returning EINVAL from content format write ops when an object
field definition is not found (an optional field which is not
implemented). Instead, return ENOENT which lets the LwM2M engine
know to send ZOAP_RESPONSE_CODE_NOT_FOUND to the LwM2M server at the
end of handle_request().
NOTE: This behavior is not correct when we call the writer right after
a CREATE operation where the data is assigned to resources for the
first time. This case will be handled in a follow-up patch once we're
able to distinguish between a WRITE and a CREATE in the write op
handler.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
POSIX requires struct sockaddr's field to be named "sa_family"
(not just "family"):
http://pubs.opengroup.org/onlinepubs/009696699/basedefs/sys/socket.h.html
This change allows to port POSIX apps easier (including writing
portable apps using BSD Sockets compatible API).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
net_pkt_get_reserve_data ignores the timeout parameter when in isr,
using K_NO_WAIT instead, which can lead to invalid fragment.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Per LwM2M specification 5.3.1 Register, report "ct=11543" when JSON is
supported. Also, report the resource type as rt="oma.lwm2m" when "ct="
presents.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Per LwM2M specification 5.3.1 Register. When object instances are
available, object ID can be ignored in registration message
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
According to LwM2M specification 5.2.7.3 Bootstrap DISOCVER,
security object is only reported to the bootstrap server.
Correct the behavior to (1) report server object to the server
(2) do not report security object at registration time
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
This is how it's called in the main docs, so use this same phrase in
Kconfig and samples too.
Also, added some articles to docs.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This option enables full debugging output for memory allocations.
As that can produce lot of output and slow down the device under test,
it is disabled by default.
The previous CONFIG_NET_DEBUG_NET_PKT will collect information about
memory allocations but will not print any output. Use "net mem" or
"net allocs" commands in net-shell to see the memory allocation status.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Because the name of the memory pool can be quite long, print
it last so that the columns get aligned nicely.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we are not in ESTABLISHED state, then there is no need to
try to resend any pending data packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the expire send timer expires, then it sends the packet.
If that happens, then we must not try to send the same packet
again if we receive ACK etc. which can cause re-sends to happen.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the packet sending is slow then we must NOT increment the ref
count when re-sending it. This is unlikely but can happen if there
are lot of debug prints etc. extra activities that prevent the driver
to actually send the packet fast enough.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that the sent flag is only set after we have really
sent the packet and the driver has verified that.
If the net_pkt_set_sent() is called while still in tcp.c, then
depending on how fast the device is, it might happen that the
retry timer expires before the packet is actually sent. This was
seen in frdm-k64f with ethernet and various debug prints activated.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is a backlog entry when TCP context is released, then
cancel the ACK timer if one exists.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that a network packet is sent after calling
http_response_send_data(). Othwerwise the packets might be
piling up and not sent in timely manner.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some older C libraries do not have errno for EPFNOSUPPORT.
Fixes issues with newlib in some versions of Xtensa XCC compiler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The initial function prototype did not have 'inline' in it,
resulting in a compiler warning with XCC.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
It's never a good idea to redefine functions as macros if intended
to be unused in some configuration
- "statement with no effect" warnings
- "unused argument" warnings
- No type checking done if the macros are used
These have been redefined as empty inline functions.
Fixes compiler warnings with XCC.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The second 'const' is misguided, indicating that the returns pointer
value itself cannot be changed, but since pointers are passed by value
anyway this is not useful and was generating warnings with XCC.
The leading 'const' indicates that the memory pointed to is constant,
which is all we needed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Inline functions declared in header files need to be declared
static. Fixes a compiler warning with XCC compiler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Currently, the HTTP_NETWORK_TIMEOUT setting is hard-coded as 20 seconds.
Not every application may want to wait that long, so let's change this
to a CONFIG option: CONFIG_HTTP_CLIENT_NETWORK_TIMEOUT
NOTE: This also removes HTTP_NETWORK_TIMEOUT from the public http.h
include file. It was not being used externally to HTTP client sources.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
A TCP FIN message is passed on to user apps as a tcp_received_callback
with a NULL pkt parameter. This means the connection is closing and
the app should do whatever cleanup it needs as there will be no further
callbacks for the current TCP connection.
Currently, if a HTTP client request doesn't receive a "body" which
the HTTP parser can use to trigger on_message_complete, then the request
will end up timing out and most apps will think an error has occurred.
Instead, let's handle the TCP FIN message and return the waiting
semaphore, leaving the app to deal with whatever has been set in the
current HTTP context response data (IE: http_status).
This fixes using HTTP client to send POST data to servers which
only respond with HTTP_OK status and no body.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
"Network Application Support" itself is renamed from "Network
Applications" and also includes net_app API.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This is needed in order to get information which function is
doing the ref. With inline function this was not possible.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of printing [net/net_pkt], print [net/pkt] if debug log
is enabled for network packet allocator. The double net in earlier
print is redundant information.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of always have CONFIG_NET_IPV6_MAX_NEIGHBORS parents,
use CONFIG_NET_RPL_MAX_PARENTS when creating the parent table.
Default value for max parents is the max neighbors so no
functionality changes are introduced here.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of always having CONFIG_NET_IPV6_MAX_NEIGHBORS number
of items in neighbor pool, store the neighbor count in the pool
and use that value when traversing the neighbor table.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Allow user to define what kind of network the RPL should serve.
Currently options will be either ANY or IEEE802154. If there
is only one network interface in the system, then ANY will take
the default network interface and use that. If there are multiple
network interfaces, then one should not use ANY as the default
network interface might not be the expected one.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print network interface where the DIO, DIS or DAO was sent. This is
useful if we have multiple network interfaces in the system.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When printing network interface specific data, print also
the type of the network interface (ethernet, bluetooth etc).
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the user has not specified CONFIG_NET_APP_MY_IPV4_ADDR or
CONFIG_NET_APP_MY_IPV6_ADDR, the value is set to "" in this case.
This will be converted to ANY IP address which is not useful
to be set to the network interface. So check this and just
continue the init in this case without setting the IP address.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The documentation says that the API will automatically append the
net_buf fragment to the end of network packet fragment chain.
This was not the case and current only user for this API in
echo-server sample appended the fragment itself. The fix is to
automatically append the fragment to the end of fragment chain.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
1. According to the specification 5.3.1, it's a MUST to specify
(1) content format: app link format (2) supported lwm2m version.
Also, we should use text/plain instead of LWM2M's (obsolete).
2. Use LWM2M_FORMAT_OMA_TLV as default accept format when accept option
is not given from the caller for TLV is a MUST have in LwM2M spec and
it can deals w/ multiple resources read
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Save in observe_node_data so that later on we can select the correct
content format requested by the caller at the first time
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Function do_write_op_tlv() uses in->inbuf and in->insize as a looping
condition to iterate through items in TLV payload and call
do_write_op_tlv_item() to update the value.
However, do_write_op_tlv_item() will override the value before calling
for fitting the usage of lwm2m_write_handler() function without restore
them. (lwm2m_write_handler() is also called by plain text/json writer
and is expecting in->inbuf is the start of buffer and in->insize as the
length of the buffer)
This will result in errors in do_write_op_tlv().
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
RFC-7230 "HTTP/1.1 Message Syntax and Routing" Section 5.4
describes the "Host" header formatting. If Zephyr user
specifies a host string as a part of the HTTP client request
structure, we end up sending an incorrect HTTP header due
to a missing "Host :" text.
Fix this by prepending "Host: " to the header data before
the user supplied host string.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
sprint_token is only used by SYS_LOG_DBG, so only build it when
CONFIG_SYS_LOG_LWM2M_LEVEL > 3.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Separate response can happen when handling block transfer for firmware
updates, and to avoid duplicating the lwm2m_udp_receive function, create
and additional flag to allow handling CoAP separate response messages.
This is required to avoid removing the reply callback, since a new
message (with a valid token) will be received later from the server.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Simplifly net_context_sendto calls and also allows to easily debug every
send/receive lwm2m call.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
If the device has multiple network interface, then we must not
blindly use the default one but get the IEEE 802.15.4 network
interface when setting radio parameters in the shell.
Jira: ZEP-2432
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print route information by groupping them for each network
interface like this:
IPv6 routes for interface 0xa8007140
====================================
IPv6 prefix : 2001:db8::212:4b00:0:3/128
neighbor : 0xa80065e0
link addr : 00:12:4B:00:00:00:00:03
IPv6 prefix : 2001:db8::212:4b00:0:1/128
neighbor : 0xa8006660
link addr : 00:12:4B:00:00:00:00:01
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add "net rpl" command to net-shell which will return both static
RPL configuration from Kconfig, and dynamic run time configuration
of the nodes and parents.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create net_rpl_foreach_parent() function that will traverse
through all the parents and return their information via callback.
This is needed by net-shell in later commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If debug level was low but debugging was activated, then some
of the debug variables were left unused.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_rpl_repair_root() and net_rpl_set_root_with_version()
functions were static which prevented global repair when using
an instance id. Making those functions global allows RPL network
repairing from shell for example.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit b14586c3ca ("net: rpl: RPL route entry was fetched
too late") dropped the DAO packet too early which prevents the
RPL root node functionality. Rework the earlier commit so that
Coverity issues are fixed but the RPL DAO message is also properly
handled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
IPSO Smart Objects are a set of template objects based on the LwM2M
object framework which are designed to represent standard hardware
such as temperature and humidity sensors or light controls.
Let's add a place for these objects to live as well as an initial
temperature sensor object.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Origin: SICS-IoT / Contiki OS
URL: https://github.com/sics-iot/lwm2m-contiki/tree/lwm2m-standalone-dtls
commit: d07b0bcd77ec7e8b93787669507f3d86cfbea64a
Purpose: Introduction of LwM2M client library.
Maintained-by: Zephyr
Lightweight Machine-to-Machine (LwM2M) is a protocol stack extension
of the Constrained Application Protocol (CoAP) which uses UDP
transmission packets.
This library was based on source worked on by Joakim Eriksson,
Niclas Finne and Joel Hoglund which was adopted by Contiki and then
later revamped to work as a stand-alone library.
A VERY high level summary of the changes made:
- [ALL] sources were re-formatted to Zephyr coding standards
- [engine] The engine portion was re-written due to the heavy reliance
on ER-CoAP APIs which are not compatible to the Zephyr CoAP APIs as
well as other Zephyr specific needs.
- [engine] All LWM2M/IPSO object data is now abstracted into resource
data which stores information like the data type, length, callbacks
to help with read/write. The engine modifies this data directly (or
makes callbacks) instead of all of the logic for this living in each
object's code. (This wasn't scaling well as I was implementing
changes).
- [engine] Related to the above change, I also added a generic set of
getter/setter functions that user applications can call to change
the object data instead of having to add getter/setting methods in
each object.
- [engine] The original sources shared the engine's context structure
quite extensively causing a problem with portability. I broke up the
context into it's individual parts: LWM2M path data, input data and
output data and pass only the needed data into each set of APIs.
- [content format read/writer] sources were re-organized into single
.c/h files per content formatter.
- [content format read/writer] sources were re-written where necessary
to remove the sharing of the lwm2m engine's context and instead only
requires the path and input or output data specific to it's
function.
- [LwM2M objects] re-written using the new engine's abstractions
Signed-off-by: Michael Scott <michael.scott@linaro.org>
In the 08 Feb 2017 V1.0 LwM2M specification page 80 mentions: in
response to a "Notify" operation for which it is not interested in
any more, the LwM2M Server can send a "Reset Message".
Leshan server sends this CoAP RST response and it does not contain
the originating message token (which is also how the packet flow looks
on page 81 of the LwM2M spec). Using the current ZoAP sources, the
client has no way of matching back to observation which needs to be
cancelled.
Let's add a match for message ID of a reply where there is no token
to handle this case.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
[ricardo.salveti@linaro.org: Handle both piggybackend and separate
response (id doesn't need to match, only token).]
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
For an accepted socket, we should set our receive callback and start
to queue packets ASAP (in the accept callback itself). Otherwise,
(if done in accept() call like before) we may miss to queue some
packets.
This issue wasn't exposed with slow SLIP and with emulated QEMU, but
easily exposed with Ethernet on a real hardware.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
We need to define __LINUX_ERRNO_EXTENSIONS__ if newlib is being
used otherwise there is a compile error about ESHUTDOWN errno
value missing.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
- Fix typo'd "&&" when checking bit value
- Don't use NET_EVENT_IPV6_ADDR_ADD for checking mask value
due to combination of bits: _NET_EVENT_IPV6_BASE |
NET_EVENT_IPV6_CMD_ADDR_ADD
Instead use NET_EVENT_IPV6_CMD_ADDR_ADD so the check works
when NET_EVENT_IPV6_ROUTER_ADD is enabled.
Tested fix with echo_server on x86 qemu where it was previously
broken.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Unlikely to happen but make sure parent neighbor exists when
probing it.
Coverity-CID: 173635
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is no parent found with a specific dag, then we have
to check this in order not to access NULL pointer.
Coverity-CID: 173637
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the parent is not found when adding DAG, then just return.
We must check the parent pointer as it can be NULL.
Coverity-CID: 173638
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
No need to complex overflow checks that are error prone.
Coverity complained that the original diff check was always
false.
Coverity-CID: 173639
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There was dead code when handling IPv6 Hop-by-hop option.
The extra option value check can be removed as it is useless.
Coverity-CID: 173642
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Coverity complains about non-checked return values here. This is false
positive as the return values do not need checking in this special
case because we are closing the socket.
Coverity-CID: 173646
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Coverity complains about reversed src and dst fields when sending
DAO ack back to originator. This is false positive.
Coverity-CID: 173650
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Check the return value of k_poll() as instructed by Coverity.
If debugging is enabled we print error if this happens, otherwise
this error is ignored. In our case the return value should always
be 0.
Coverity-CID: 173652
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It is be possible that the local address was not properly
resolved in which case the local_addr variable could be NULL.
This will cause NULL pointer access if the variable is used.
Coverity-CID: 173656
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The RPL route entry variable "extra" was resolved inside an
if-statement and the code was always returning from it.
This meant the the later code dealing with "extra" was never
executed. Fixed by moving the resolving of "extra" a bit
earlier so that the "extra" variable has always a proper value.
Coverity-CID: 173659
Coverity-CID: 173654
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The TX send function will return status < 0 if there is an error
when sending. This status value was incorrectly checked.
Coverity-CID: 173660
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As we buffer incoming packets in receive callbacks, we must decrease
receive window to avoid situation that incoming stream for one socket
uses up all buffers in the system and causes deadlock. Once user app
consumes queued data using recv() call, we increase window again.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This fixes the existing situation that "if application buffers data,
it's the problem of application". It's actually the problem of the
stack, as it doesn't allow application to control receive window,
and without this control, any buffer will overflow, peer packets
will be dropped, peer won't receive acks for them, and will employ
exponential backoff, the connection will crawl to a halt.
This patch adds net_context_tcp_recved() function which an
application must explicitly call when it *processes* data, to
advance receive window.
Jira: ZEP-1999
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This enables IPSP node role which requires IPSS GATT service to be
registered.
Jira: ZEP-2451
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds NET_REQUEST_BT_ADVERTISE which can be used to advertise
IPSS service so the remote devices can connect to it.
Jira: ZEP-2451
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some network interfaces such as bluetooth 6lowpan can start without
an assigned IP address and then later once the connection is up a
router advertisement broadcast will assign the IP address.
The net_app framework will timeout out during network init if a value
cannot be parsed from CONFIG_NET_APP_MY_IPV6_ADDR. Let's adjust
the framework to handle a missing value there and fill it in later
when the IPv6 address is added to the interface.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
ReST defines interpreted text roles where text enclosed by single quotes
can be "intrepreted", for example :ref:`some name` becomes a link to
a label anywhere in the doc set named "some name", :c:func:`funcname()`
becomes a link to the API documentation for "funcname", and
:option:`CONFIG_NAME` becomes a link to, in our case, the documentation
for the generated Kconfig option.
This patch fixes uses of `some name` (without a role) by either adding
an explicit role, or changing to ``some name``, which indicates inline
code block formatting (most likely what was intended).
This is a precursor to changing the default behavior of interpreted
text to treat `some name` as :any:`some name` (as configured in
doc/conf.py), which would attempt to create a link to any available
definition of "some name".
We may not change this default role behavior, but it becomes an option
after the fixes in this patch. In any case, this patch fixes incorrect
uses of single-quoted text (possibly introduced because GitHub's
markdown language uses single-quoted text for inline code formatting).
Jira: ZEP-2414
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Historically, stacks were just character buffers and could be treated
as such if the user wanted to look inside the stack data, and also
declared as an array of the desired stack size.
This is no longer the case. Certain architectures will create a memory
region much larger to account for MPU/MMU guard pages. Unfortunately,
the kernel interfaces treat both the declared stack, and the valid
stack buffer within it as the same char * data type, even though these
absolutely cannot be used interchangeably.
We introduce an opaque k_thread_stack_t which gets instantiated by
K_THREAD_STACK_DECLARE(), this is no longer treated by the compiler
as a character pointer, even though it really is.
To access the real stack buffer within, the result of
K_THREAD_STACK_BUFFER() can be used, which will return a char * type.
This should catch a bunch of programming mistakes at build time:
- Declaring a character array outside of K_THREAD_STACK_DECLARE() and
passing it to K_THREAD_CREATE
- Directly examining the stack created by K_THREAD_STACK_DECLARE()
which is not actually the memory desired and may trigger a CPU
exception
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
A new net-shell command "net app" will print information about
network app users in the system.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add API that allows net-shell to get net_app context information
that can be used to debug net_app connections.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds http_client_set_net_pkt_pool() function that allows
caller to define net_buf pool that is used when sending a TCP packet.
This is needed for those technologies like Bluetooth or 802.15.4 which
compress the IPv6 header during send.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For IPv6 header compressed packet, the IP header offsets will
be wrong. In this case there is no need to print error when
trying to print TCP packet information.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds http_server_set_net_pkt_pool() function that allows
caller to define net_buf pool that is used when sending a TCP packet.
This is needed for those technologies like Bluetooth or 802.15.4 which
compress the IPv6 header during send.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
CONFIG_MQTT_LIB_TLS is introduced to enable TLS support.
Also, prj_frdm_k64f_tls.conf is added to demostrate the whole idea.
jira:ZEP-2261
Signed-off-by: Aska Wu <aska.wu@linaro.org>
Use net app API since we want to enable MQTT with TLS.
mqtt_connect() and mqtt_close() are added to build and close the
connection to the broker. The caller doesn't need to deal with
the net context anymore and the most of network setup code in
mqtt_publisher is removed.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
As SLIP TAP is now the default after the commit ca0ad13a61
("net: enable SLIP only on QEMU targets"), clarify the comments
and settings in various Kconfig files that talk about slip.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
If the network interface is down, then IPv6 DAD (Duplicate
Address Detection) cannot be done if new IPv6 address is added
to the network interface. This can happen in Bluetooth, where
network interface is taken up only after there is a BT connection.
The DAD is delayed and done later after the network interface is up.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Normally network interface is always UP, but Bluetooth
interfaces are down until connected. So if this is the case,
then check the interface status before trying to access variables
that are NULL. This was seen with "net iface" shell command when
BT was enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In case the application is using NET_L2_BLUETOOTH the SLIP drivr shall
not be selected as bus they cannot coexist since they use the same UART
port:
arch/x86/soc/ia32/Kconfig.defconfig:
config BLUETOOTH_UART_ON_DEV_NAME
default "UART_1"
config UART_PIPE_ON_DEV_NAME
default "UART_1"
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In many networking tests we had to configure SLIP in the prj.conf
leaving those configurations Qemu specific. This change enables SLIP for
QEMU targets automatically and allows reuse of prj.conf for multiple
boards.
Additionally, the TUN options is removed. This option was not used
anywhere.
To enable self-contained networking tests that do not depend on SLIP, we
introduce the new option NET_TEST which disables TAP and allows testing
in QEMU without the need for a host interface.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
* Fix the indentation which was caused by uint32_t -> u8_t changes.
* Make sure there is no unused variable warning if debugging is
enabled but debug level is low.
* Add assert that checks that Imax_abs is > 0 which it should be.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there are no neighbors or there is no route to one specific
neighbor, then check the NULL pointer before accessing the route.
This issue was seen with "net route" shell command.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_stack_analyze function wants to look at the stack buffer,
but it is making assumptions on where this data is that are no
longer valid. Change to use the proper APIs for referencing this.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
If IEEE 802.15.4 is enabled, then setup the network settings
automatically so that the device is ready for IP configuration.
This is only done if CONFIG_NET_APP_AUTO_INIT is enabled, which
is currently the default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The address lifetime timer was cancelled always even if the address
timer was never installed.
Jira: ZEP-2397
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
poll() allows to (efficiently) wait for available data on sockets,
and is essential operation for working with non-blocking sockets.
This is initial, very basic implementation, effectively supporting
just POLLIN operation. (POLLOUT implementation is dummy - it's
assumed that socket is always writable, as there's currently no
reasonable way to test that.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Use net_context_put(), not net_context_unref(). This makes sure
that after sending response, connections are properly closed.
Jira: ZEP-2362
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Introduce net_context_bind_default() to ensure that local address is
set for context if not yet (via explict bind() call). This fixes
dereferences of NULL pointer to local address which was exposed when
MMU was enabled for qemu_x86.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
According to RFC7959 page 30, "The end of a block-wise transfer is
governed by the M bits in the Block options, _not_ by exhausting the
size estimates exchanges."
Therefore, we should check the M bit instead of total size (which
is not always available, too)
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
If either UDP or TCP is enabled but not both, then connectivity
fails. This was a side effect of commit 3604c391e ("net: udp:
Remove NET_UDP_HDR() macro and direct access to net_buf")
Jira: ZEP-2380
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When IPv6 fragments were sent, the last IPv6 fragmented packet
was accessing NULL pointer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When the ARP message is received when the device is starting up,
the network interface might not yet have IPv4 address setup
correctly. In this case, the IP address pointer could be NULL
and we must not use it for anything.
Fixes#752
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Coverity reported false positives, add comment about these in
the code.
Jira: ZEP-2344
Jira: ZEP-2345
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch fixes a regression which the original patch introducing
this code (improving concurrent connection handling) had on
*sequential* connection handling. Without this patch, with the
default CONFIG_NET_TCP_BACKLOG_SIZE of 1, after each connection
request, there was 1s (ACK timeout) "dead time" during which new
connection wasn't ptocessed.
This is because k_delayed_work_remaining_get() was checked the
wrong way. But there's no need to use k_delayed_work_remaining_get()
at all, instead just call k_delayed_work_cancel() and dispatch on
its return code.
Note that there's still a problem of synchronizing access to
the global array tcp_backlog, as worker (which modifies it) may
preempt packet handling code (which also modifies it).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The sequence number validator was checking the seq numbers
incorrectly. This caused some valid RST packets to be dropped
and the TCP stream to hang.
Added also a TCP test case that tests the seq validator.
Jira: ZEP-2289
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Usually it is not enough to have just one IPv6 multicast
address defined for the network interface. So allocate three
IPv6 multicast addresses for the network interface as IPv6
by default uses multicast a lot. This hopefully will avoid
some mysterious errors if the addresses run out.
Note that this will increase memory usage a bit so you might
need to lower the count in your conf file if memory is low.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit 210c30805b ("net: context: Close connection fast
if TIME_WAIT support is off") was not a proper way of closing
the connection. So if Zephyr closes the connection (active close),
then send FIN and install a timer that makes sure that if the peer
FIN + ACK is lost, we close the connection properly after a timeout.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit 00ac0487b0 ("net: context: Remove tcp struct SYN-ACK
timer handling") removed also the passive close ACK timer.
Adding that ACK timer back so that we can close the connection
properly even if the last ACK from peer is lost.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Upcoming memory protection features will be placing some additional
constraints on kernel objects:
- They need to reside in memory owned by the kernel and not the
application
- Certain kernel object validation schemes will require some run-time
initialization of all kernel objects before they can be used.
Per Ben these initializer macros were never intended to be public. It is
not forbidden to use them, but doing so requires care: the memory being
initialized must reside in kernel space, and extra runtime
initialization steps may need to be peformed before they are fully
usable as kernel objects. In particular, kernel subsystems or drivers
whose objects are already in kernel memory may still need to use these
macros if they define kernel objects as members of a larger data
structure.
It is intended that application developers instead use the
K_<object>_DEFINE macros, which will automatically put the object in the
right memory and add them to a section which can be iterated over at
boot to complete initiailization.
There was no K_WORK_DEFINE() macro for creating struct k_work objects,
this is now added.
k_poll_event and k_poll_signal are intended to be instatiated from
application memory and have not been changed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This fixes coverity CID 171565 which may be valid in case of the
connection is not properly setup, or its memory is corrupted, it
may cause use of invalid addresses to be set using
net_if_set_link_addr.
JIRA: ZEP-2344
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the TCP data packet needs to be re-sent after the packet is lost,
then the acknowledgment number will be changed. This then means that
the TCP checksum needs to be recalculated too.
Signed-off-by: june li <junelizh@foxmail.com>
When a node receives consistent DIO messages with same data from
Border Router just ignore those messages. Need not to proceed
further.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Link metric is part IPv6 neighbour data struct. But RPL code is
trying to access it from RPL parent table where link metric doesn't
exist. So provided an api to get IPv6 neighbour data from RPL parent
data.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
DAG rank will be properly written with net_pkt_write_be16() in
network packet. API will take care of endianness. So need
not to convert it using htons().
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Sender rank (16 bit uint) was properly read with net_frag_read_be16()
api and need not to convert it again using ntohs().
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
We had various asserts when checking network packet length but
printed also error when there was none. Fix this by checking
do we really have a too short message.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_TCP_HDR() macro as we cannot safely access TCP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the TCP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_UDP_HDR() macro as we cannot safely access UDP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the UDP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_ICMP_HDR() macro as we cannot safely access ICMP header
via it if the network packet header spans over multiple net_buf
fragments.
Jira: ZEP-2306
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IPv6 HBH option PAD1 ext header was not parsed properly
as the code read one extra byte from the ext header. The
PAD1 length is only 1 byte.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add utility function that helps to figure out if the
protocol headers can be directly accessed when they fit one
net_buf fragment, or if they need to accessed using various
net_pkt helpers that know about reading data from two
different net_buf's.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of directly setting pointer to where to start to calculate
the various IP related checksums, use the net_frag_skip() to first
find out what is the fragment where the calculation should start.
This needs to be like this so that if the IP header + possible
extension are so long that they do not fit the first fragment,
we need to be prepared to look into second fragment.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
net_context_unref() is protocol agnostic, after being un-referenced,
the same context might end up being used then for UDP,
if context->tcp is not reset to NULL, calling net_context_unref()
after this UDP usage will again try to release this TCP pointer
which might lead to random error.
Signed-off-by: june li <junelizh@foxmail.com>
In some cases the lladdr might not be set, currently this is
seen with RPL unit tests, in which case we must not access
the lladdr.
Jira: ZEP-2330
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is no route to the neighbor, then do not try to delete
it because the route pointer is NULL.
Jira: ZEP-2329
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The SYN-ACK timer is now handled by the TCP backlog functionality,
while the remaining ACKs for established connections use the tcp
struct ack timer. With this, code setting tcp struct SYN-ACK state
timers can now be removed.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Add timer for sent TCP SYN-ACKs. If the timer is already
scheduled to run before canceling it is attempted, set
the cancelled flag and let the callback remove the
delayed work.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Add an array of configurable size that holds TCP backlog entries.
The array is shared between all incoming TCP connections in order
to make it possible to get away with less memory consumed than
with a connection based approach.
The backlog entries are created when a SYN is received for a
listening TCP socket and removed once the corresponding ACK is
seen. With an incoming RST the corresponding backlog entry is
cleared, if any.
The size of the global backlog array is defined with the
CONFIG_NET_TCP_BACKLOG_SIZE Kconfig variable.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
When neither IPv4 nor IPv6 are selected the limit that is
passed to k_sem_init will end up being 0, which will trigger
the folowing assertion in k_sem_init;
__ASSERT(limit != 0, "limit cannot be zero");
Fixed by not passing count as initial and limit value but
only as initial value and use UINT_MAX as limit.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
The network application API is a higher level API for creating
client and server type applications. Instead of applications
dealing with low level details, the network application API
provides services that most of the applications can use directly.
This commit removes the internal net_sample_*() API and converts
the existing users of it to use the new net_app API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If ICMP packets do not fit in 1 net_pkt fragment the checksum
will be calculated incorrectly.
The problem shows up when using ping with the -s option to
create large ping requests. Eventhough the ping command does
accept the reply without complaining, Wireshark warns that
the icmp checksum is incorrect.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
If a socket is closed without reading all data from peer or accepting
all pending connection, they will be leaked. So, flush queues
explicitly.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
With CONFIG_NET_SOCKETS_POSIX_NAMES=y, "raw" POSIX names like
socket(), recv(), close() will be exposed (using macro defines).
The close() is the biggest culprit here, because in POSIX it
applies to any file descriptor, but in this implementation -
only to sockets.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This adds Kconfig and build infrastructure and implements
zsock_socket() and zsock_close() functions.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The global mbedtls heap is set automatically now so no need to
set it individually in the http library.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Three response codes are missed in zoap_header_get_code() which will
result in the response code returned from the function being set as
ZOAP_CODE_EMPTY. Check include/net/zoap.h for the missing code
definition.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
In LISTEN state ignore a TCP RST. In SYN RCVD state, reset TCP
connection state to LISTEN when a valid RST segment is received. In all
other states close the connection - except that these other states will
not be handled in tcp_syn_rcvd() function.
Jira: ZEP-2279
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
If the CONFIG_NET_TCP_TIME_WAIT support is disabled, then do not
start to wait for reply to sent FIN in active close, but unref
the corresponding net_context in order to close the connection
as soon as possible.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Moving the net_buf_pool objects to a dedicated area lets us access
them by array offset into this area instead of directly by pointer.
This helps reduce the size of net_buf objects by 4 bytes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The net_pkt_split() was incorrectly checking fragA pointer
even before it was allocated.
The unit test is fixed and converted to ztest.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
From
http://pubs.opengroup.org/onlinepubs/7908799/xns/netinetin.h.html:
in_addr_t
An unsigned integral type of exactly 32 bits.
[] the in_addr structure [] includes at least the following member:
in_addr_t s_addr
In other words, POSIX requires s_addr to be a single integer value,
whereas Zephyr defines it as an array, and then access as s_addr[0]
everywhere. Fix that by following POSIX definition, which helps to
port existing apps to Zephyr.
Jira: ZEP-2264
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If we receive a HTTP request and if the earlier context is still
active and it is not the same as the new one, then close the earlier
one. Otherwise it is possible that the old context will be left into
TCP ESTABLISHED state and would never be released. Example of this
is that we had IPv4 connection active and then IPv6 connection is
established, in this case we will disconnect the IPv4 connection
after this commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Given that K_NO_WAIT is passed as a timeout to net_context_recv(), it's
unlikely this function will return any error value. It's cheap to
check, though, so do it.
Coverity-CID: 170580
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The shell takes care of removing the module name so it is no longer
necessary to have this adjustment.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In certain TCP states we should not try to send RESET segment
to peer. So check this and do not try to use NULL pkt to send
a message.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The "net http monitor" command turns on HTTP monitoring,
which means that for each incoming HTTP or HTTPS request,
a information about source and destination address, and
the HTTP request URL is printed.
User can disable the monitoring by "net http" command.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If CONFIG_NET_DEBUG_HTTP_CONN is enabled, then start to collect
currently active HTTP connections to HTTP server.
This is only useful for debugging the HTTP connections.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we cannot send network data, then print the error code when
printing debug information about the issue. This is needed when
debugging the issue.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add HTTPS support into http-client library. The init of the
HTTPS client connection is different compared to HTTP client,
but the actual HTTP request sending is using the same API as
HTTP client.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is done so that both http_client and http_server functionality
can share the same heap.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When src and dst addresses are compressed based on context
information, uncompression method should verify CID bit,
SAC and DAC bits and context ID's. But it has missed some
cases which resulted in invalid uncompressed IPv6 header.
e.g. CID is set, SAC is 0 and DAC is 1 and context id's provided.
Uncompression method assumed that src address is compressed based
on context information but it is not.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Empty RPL HBH header will be inserted while finalizing IPv6 packet
but updated after finding nexthop and sent the packet. In case of
Bluetooth or multicast dst address it was missed. Resulted in
empty RPL HBH header and packet dropped at peer node. It should
be updated in all circumstances.
Jira: ZEP-2088
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The mbedtls debugging function was set before the ssl config
struct was initialized. This meant that it was not possible
to activate mbedtls debug prints. This commit sets the debug
print option after the config struct has been initialized.
Fixed also the debug prints which print extra \n which looks
very bad in debugging outputs.
This commit does not enable mbedtls debugging, it just makes it
possible to output mbedtls debug prints. In order to get mbedlts
debug prints one needs to do this:
* set DEBUG_THRESHOLD to >0 in http_server.c
* enable CONFIG_NET_DEBUG_HTTP in project config file
* enable MBEDTLS_DEBUG_C in mbedtls config file (see file pointed
by CONFIG_MBEDTLS_CFG_FILE option)
* in qemu, one needs to increase the size of the available RAM,
this setting does the trick, CONFIG_RAM_SIZE=300
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Semantics of ENOENT error as used previously is "named entity not
found", whereas for "I/O handle is not valid", there's EBADF. For
example, POSIX/SUSV2 doesn't even list ENOENT as a possible error
for accept(), connect(), recv(), etc. whereas it lists EBADF, e.g.:
http://pubs.opengroup.org/onlinepubs/7908799/xns/connect.html
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Instead of waiting forever for a free net_buf, set a timeout to
the allocations (500 ms). This way the application will not be
blocked by memory exhaustion.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In some cases the net_pkt can be null when freeing it,
this will print error from net_pkt library. Avoid this by
checking the value of net_pkt before calling net_pkt_unref().
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we re-connect to same peer server, then we should select a new
source port. Noticed that if the same source port as before is
used for the new connection, the peer might drop the packet. This
was seen when connecting to Linux peer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Defines a new tunable, CONFIG_NET_TCP_RETRY_COUNT, that determines the
number of segment retransmissions that the IP stack will attempt to
perform before resetting the connection.
The default value is 9 retransmissions, which amounts to 1:42 minutes,
as close as possible to the minimum recommended by RFC1122.
Jira: ZEP-1956, ZEP-1957
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
If we receive unknown option in neighbor advertisement message,
then skip those properly. Old code did not check the length of
the extension options which could cause infinite loop.
Jira: ZEP-2219
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
If we received a bad HTTP request, then subsequent good requests
were also returning 400 error code. The parsing state needs to
be initialized after each received HTTP request.
Jira: ZEP-2181
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fixes the following issue:
"In expression 1UL << chan - 1U, left shifting by more than 31
bits has undefined behavior. The shift amount, chan - 1U, is
4294967295."
Coverity-CID: 167140
Jira: ZEP-2131
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Print also network buffers that are allocated by the IPv6
fragment handler. This is very useful in debugging.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the user really wants, it is possible to increase the
maximum size of the fragmented packet. According to RFC 2460
chapter 5, we do not need to accept larger than 1500 byte IPv6
packets, so the max pkt limit is set to 2. But if really needed
the limit can be raised by defining NET_IPV6_FRAGMENTS_MAX_PKT
to some new value. Currently there is no Kconfig option for
doing this as it is unlikely that this is needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The cancellation of reassembly did not work as expected because
K_WORK_INITIALIZER() did not setup the timeout function properly.
So do the timer initialization at runtime instead.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IPv6 fragmentation was not working properly when the large
IPv6 packet was being sent. There is unit tests in next commit
that will test the IPv6 fragmentation sending.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the fragmented IPv6 packet was very large, we could run out
of resources. When that happened, we leaked the memory for the
pending fragments that were waiting reassembly.
Jira: ZEP-2166
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The previous default 60 seconds is way too long for our limited
amount of memory. It might be that the 5 sec is still too long
but that can be changed in the future.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Shell itself already have a help command, so instead of creating a net
specific help just fill the help description of each command.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Shell modules are registered at link time thus it makes no sense to
leave it behind net_shell_init.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the HTTPS connection is closed, then properly handle call to
HTTP parser init in case of error and also remove any pending
data that belong to old connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive unknown option in neighbor solicitation message,
then skip those properly. Old code did not check the length of
the extension options which could cause infinite loop.
Jira: ZEP-2174
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we could not split the packet properly, make sure that the
fragments that we managed to allocate are unreffed and marked
as NULL.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print also the character when hexdumping a memory area.
This is useful so that one does not need to convert hex
values to characters in head. Unprintable chars are printed
as '.'
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
No need to check attr and path variables for null as they
cannot be null.
Coverity-CID: 157595
Coverity-CID: 157602
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Allow the caller to delay the closing of the HTTP connection
for a number of milliseconds. The purpose for this is that
the client can send still some data back to us for a short
period of time.
This is needed for example for Basic authentication so that
server is able to receive authentication values back.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The address family of the UDP port listener was not set. This
caused weird debug prints in net-shell. Now the listener will
be registering IPv4 any address as it should.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When a connection handler was registered, the checker function
introduced in commit 43b37cef ("Check duplicate UDP/TCP connection
handlers") did not check the address family (IPv4 or IPv6) of
the local end point properly. This caused duplicate connection
error to be returned to the caller.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The uncompressed source address in packets was not handled properly if
NET_6LO_CONTEXT was enabled.
This implementation is identical to the contextless case.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
If we do not receive last ACK when the connection is tore down,
then do not wait forever as that would eat all the resources in
the network stack. So when we enter the LAST_ACK state, we setup
a timer that will unref the connection if the last ACK is not
received.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Without change to add ACK to FIN, invalid TCP packet is generated,
where ack sequence number is non-zero. Without adjusting sequence
number as done, ACK which we send in response to peer's FIN/ACK is
not recognized by peer, and peer keeps retransmitting its FIN/ACK.
Jira: ZEP-2104
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
When connection handler was unregistered, we did not remove
it from cache. This caused invalid connection to be passed to
net_context after connection unregister if connection caching
was enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We did not check UDP or TCP checksum to be valid after receiving
the packet. Fix this so that the checksum is validated when
packet is received in connection handler. As the checksum validation
can be resource intensive, do it after we have verified that
there is a connection handler for this connection.
The checksum calculation can be turned OFF if needed, but it is
ON by default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit "net: tcp: Handle retransmitted packets from peer"
introduced over 80 character line that was missed in review.
Fixing it now.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user has enabled RPL and STATISTICS, then enable RPL
statistics by default as that is probably what user want.
Same thing for MLD statistics.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When we receive a packet with the sequence we already seen (and
processed), the most likely cause of it is that our ACK was lost,
and peer has to retransmit that packet. Then, we should just ACK
it, because otherwise peer will retransmit it again and again,
falling into exponential backoff and hosing the entire TCP
connection.
This makes changes to send_ack(), adding a flag to force sending
an ACK regardless of its cached status, and remove inline modifier,
as the function is big and called from many places.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
We must check if we receive RST in any of the TCP states.
If we do not do this, then the net_context might leak as it
would never be released in some of the states. Receiving RST
in any TCP state is not described in TCP state diagram but is
described in RFC 793 which says in chapter "Reset Processing"
that system "...aborts the connection and advises the user and
goes to the CLOSED state."
We need to also validate the received RST and accept only those
TCP reset packets that contain valid sequence number.
The validate_state_transitions() function is also changed to
accept CLOSED state transition from various other states.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
net_if_get_default() was documented as returning "Default interface
or NULL if no interfaces are configured.", but actually didn't
return NULL in the latter case. Instead, it effectively returned
a pointer to random area of memory, shared with other system
structures, so calling functions like net_if_ipv4_set_netmask(),
etc. could trash unrelated memory.
Jira: ZEP-2105
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
RFC793, "Transmission Control Protocol", defines sequence numbers
just as 32-bit numbers without a sign. It doesn't specify any adhoc
rules for comparing them, so standard modular arithmetic should be
used.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This commit creates a HTTP server library. So instead of creating
a complex HTTP server application for serving HTTP requests, the
developer can use the HTTP server API to create HTTP server
insteances. This commit also adds support for creating HTTPS servers.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When a new UDP or TCP connection handler is to be registered,
we need to check if identical handler has already been created.
If a duplicate is found, the registering call will return -EALREADY.
The earlier code did not check this but allowed two identical
handlers to be created. The latter handler was never called in
this case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This helper copies desired amount of data from network packet
buffer info a user provided linear buffer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When we send TCP data segment, we need to set the length
of the application data by calling net_pkt_set_appdatalen().
This is done so that sequence number can be properly
advanced when we receive ACK to that pending packet.
Signed-off-by: xiaorui hu <xiaorui.hu@linaro.org>
fix misspelling in Kconfig files that would show up in configuration
documentation and screens.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Instead of separate sample application that does everything
related to HTTP client connectivity, create a HTTP client library
that hides nasty details that are related to sending HTTP methods.
After this the sample HTTP client application is very simple and
only shows how to use the client HTTP API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When adding link-local address to the cache the type needs to be
properly set as net_ipv6_addr_create_iid will attempt to use it
when generating the IPv6 address.
Jira: ZEP-2077
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This is related to commit "net: tcp: Make sure ACK timer is not
run if cancelled" which did not set the cancel flag when the timer
was cancelled from tcp.c.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
And print a warning if that happens.
This will also avoid to raise an ASSERT on net_if_tx_thread()'s k_poll
as this one will be called with no events to work with.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of returning EIO let's bubble the error from net_context_send
back up to the caller in the following functions:
mqtt_tx_connect()
mqtt_tx_disconnect()
mqtt_tx_pub_msgs()
mqtt_tx_publish()
mqtt_tx_pingreq()
mqtt_tx_subscribe()
mqtt_tx_unsubscribe()
Change-Id: I9bb4396b227b8902ac1195a97bc37eb1959b643e
Signed-off-by: Michael Scott <michael.scott@linaro.org>
With CONFIG_NET_DEBUG_NET_PKT enabled, the log messages are full of
errors regarding NULL parameters passed into net_pkt_unref in almost
every TX function for handling MQTT messages:
mqtt_tx_connect()
mqtt_tx_disconnect()
mqtt_tx_pub_msgs()
mqtt_tx_publish()
mqtt_tx_pingreq()
mqtt_tx_subscribe()
mqtt_tx_unsubscribe()
mqtt_parser()
Let's clean up the unref handling so that our debug log isn't quite
so full of error spam (as opposed to the normal amount of spam from
the net buf log).
Change-Id: Ib49d1192f51abe4329e6dc9da3c51a4a36290082
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The data->len of an inbound netbuf can be larger than a single
MQTT packet. For instance when a PINGRESP is also included
in the same netbuf. For this reason we should not be using
the data->len to determine how large the rest of the MQTT data is.
Specific Example: we've seen in testing that PINGRESP packets
can be included with a SUBACK packet in the same netbuf. Under
this case the current code uses the data->len incorrectly and
tries to find 3 QoS elements for the SUBACK packet when there
is only 1 (the rest of the data is for PINGRESP).
NOTE: A larger patch to iterate through the netbuf data parsing
individual MQTT packets will be needed to fix the MQTT subsys.
This patch only corrects the SUBACK parsing.
Change-Id: I7f6cebaaed9570b778d466de84331cf8c5060755
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Currently, app type MQTT_APP_PUBLISHER_SUBSCRIBER is not supported.
mqtt_init() will return EINVAL because the context rcv function is
either mqtt_publisher_parser or mqtt_subscriber_parser (not both).
Let's combine these functions into mqtt_parser and remove the app
type check from mqtt_init().
Change-Id: I60460e011395864706e293c997e9f8a65681b368
Signed-off-by: Michael Scott <michael.scott@linaro.org>
We need to set the mqtt context recv function prior to calling
net_context_recv which installs the mqtt_recv callback.
If not, we risk a race condition where an unprotected reference
to mqtt->rcv(mqtt, buf) is made in mqtt_recv().
Change-Id: If90ee58f4ea6f7879ef7c12b969ba27647426acc
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Some applications may want to reuse implementations of these
commands for debugging/diagnostics purpose even if they don't
use net shell per se, or implement an alternative shell.
Jira: ZEP-2064
Change-Id: I48cb66ccc41bd41a75a4eb8eb3c366316ec5a096
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
net_if_ipv6_router_add() will return router pointer on success.
This information must be cached in RPL instance, otherwise RPL
instance doesn't know about default route.
Change-Id: Ic6d80ebfa95c9a64df9adf2621ae2631d9bdb990
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When router or default router timer expired, interface will remove
router from the list. In this case RPL does not know about this.
When RPL node receives DIO messages it only verifies whether parent
exists or not. This extra checks will verify whether router really
in "used" state or not.
Jira: ZEP-2080
Change-Id: I4b36b3a2d495e76a38caddd058451daff08fab0c
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
net_if_ipv6_router_rm() is the correct API to remove IPv6 router
from the interface as it also cancels the timer and raises a mgmt
event. The net_if_router_rm() only sets router as unused and
nothing else.
Change-Id: I55114288c9ae748520b67b206edcd4f5e420b1af
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If the ./well-known/core response is bigger than L2 MTU then
response will be sent in multiple fragments. In mesh kind of networks
getting response from farthest node might loose packets. So better to
send response in a block wise fashion. Block size is configurable.
Change-Id: Id421c66597fe448c12a7215f04f63f4a284c14ab
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Value 0xFF represents End Of Options marker in CoAP message.
Use #define than magic numbers in code.
Change-Id: I3bef21ea827987f7c2e670447ee20574cb6288ae
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Add timeout for packet and buffer requests. If there are no
buffers available gracefully drop the request.
Change-Id: I56fe2b606556149c83751aadc1c5eee7828a84a8
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Bluetooth only cares about the actual payload so net_pkt can be unref
as soon as the data fragments are detached.
Jira: ZEP-2070
Change-Id: Id528d5440f42903378883f5e696b3f663bbfa313
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For stream-based protocols (TCP), adding less data than requested
("short write") is generally not a problem - the rest of data can
be sent in the next packet. So, make net_pkt_append() return length
of written data instead of just bool flag, which makes it closer
to the behavior of POSIX send()/write() calls.
There're many users of older net_pkt_append() in the codebase
however, so net_pkt_append_all() convenience function is added which
keeps returning a boolean flag. All current users were converted to
this function, except for two:
samples/net/http_server/src/ssl_utils.c
samples/net/mbedtls_sslclient/src/tcp.c
Both are related to TLS and implement mbedTLS "tx callback", which
follows POSIX short-write semantics. Both cases also had a code to
workaround previous boolean-only behavior of net_pkt_append() - after
calling it, they measured length of the actual data added (but only
in case of successful return of net_pkt_append(), so that didn't
really help). So, these 2 cases are already improved.
Jira: ZEP-1984
Change-Id: Ibaf7c029b15e91b516d73dab3612eed190ee982b
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Instead of just plain assert, check that the packet we receive
is ok before passing it to processing function.
Jira: ZEP-2057
Change-Id: I5754c82d16e1522d8fcee561eea280eadeec31ee
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The TCP trace values were not printed because of incorrect
config option used. Print also seq and ack values in decimal
in order to make it easier to correlate the values in other
prints in tcp.c.
Change-Id: I44d1535a84dcba8c6c937d348516ba801193ca23
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use ready-made utility function which can take care of endianness
Change-Id: I1edd0b2ce1a086dd637e97308145f9b434e48a1f
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
When connect to diffrent router with the same gateway ip address,
need to clear arp cache when disable interface,
or it will use the wrong gateway mac address.
Call net_arp_clear_cache function replace to set arp_table 0.
Change-Id: Ib403a0c0030832ba48824db4d2d3fcb8add63d16
Signed-off-by: june li <junelizh@foxmail.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I4ec03eb2183d59ef86ea2c20d956e5d272656837
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There was compiler error if CONFIG_NET_DEBUG_CONN was set.
Change-Id: Ibb6721c55dd2c56cd0097359a53563c6221859ea
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need to set the connect_cb for the context before sending SYN packet.
This is required if we have a loopback connection in which case everything
is happening more or less synchronously and the connect_cb would not be
called in this case because its value would still be null.
For remote network connections this patch makes no difference.
Change-Id: Id7f837cd9e81cd79c4666c98cae84f6cb1a77af0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We must not let ACK timer to run if we have already cancelled it.
So keep track that the timer is cancelled and refuse to run it
if it was indeed cancelled. The reason why the timer might be run
in this case is because the timer might be scheduled to be triggered
after which one cannot cancel it.
Change-Id: I1c8b8cee72bc7a644e02db154d9d009b8d98ade2
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The local port was set to 0 for IPv6 when registering
the connection handler. For IPv4, the code was not setting
the port in local_addr struct.
Change-Id: I82f0c08641a94d75d255ac306eca7bec6c332fba
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Without this info it is a bit difficult to notice what is going
on in loopback case.
Change-Id: I8f61330c01d025e41f00d663bd26947b8cafb5c0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support to print connection handler information in net-shell.
There exists one connection handler for each UDP/TCP port that we
are listening. These prints are only available if CONFIG_NET_DEBUG_CONN
is enabled because the net_context has the same information. Thus the
connection handler info is only printed if debugging is active in order
to verify that handler information is proper.
Change-Id: I0be39a5adb89b2cdbd85524c5d943e4a562b0fde
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If TCP debugging is enabled but if the loglevel is set to lower
than 4, then compiler prints warning about unused flags variable
in net_tcp_trace().
Change-Id: I2e663644b50fe97b75088202e21b286aa010953e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Only 2 attributes lacked this prefix, which makes sense to have, so
applying it accordingly and changing the helpers as well.
Change-Id: I095b2729f977f8fb1624eff8801a4a4e21416693
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Most of these macros are not exactly exposing a buffer, but a specific
header pointer (ipv6, ivp4, ethernet and so on), so it relevant to
rename them accordingly.
Change-Id: I66e32f7c3f2bc75994befb28d823e24299a53f5c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
IPv6 next headers are processed in a way so it is not required to store
which header has been already seen in the net_pkt, as the processing loop
can store internally which one it has seen already.
Change-Id: I266ba8a3a0081a162318cdafb474a0fc44a3185e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is actually useless as there is only 1 RX memory slab, and thus can
be removed to reduce net_pkt structure size.
Change-Id: I62d716515120e7356ee1e2d75bbe1ec32e22c35d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- net_pkt becomes a stand-alone structure with network packet meta
information.
- network packet data is still managed through net_buf, mostly named
'frag'.
- net_pkt memory management is done through k_mem_slab
- function got introduced or relevantly renamed to target eithe net_pkt
or net_buf fragments.
- net_buf's sent_list ends up in net_pkt now, and thus helps to save
memory when TCP is enabled.
Change-Id: Ibd5c17df4f75891dec79db723a4c9fc704eb843d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix warning using incorrect format specifier
Change-Id: Ib6800c40b2cd769612ae6f107e41a941926d8e66
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
We need to check whether buf_sent was true when resending the TCP
segment, and do a buf ref if needed. If this is not done, the buf
will be unref after send, which will cause unpredictable results.
Change-Id: Ibd4490305de88ac6ffd04ec42bba196e57da5c10
Signed-off-by: june li <junelizh@foxmail.com>
While very unlikely it might happen that fragment pointer is NULL
when going through fragment list.
Coverity-CID: 167148
Change-Id: Ic3dbed7ee29c7b864d4830d726f65d7f62dcea84
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If error occurs while preparing response to .well-known/core request,
do not send partly filled payload by simply changing code part only.
It's better to unref the partly filled reponse and prepare a new error
response and send.
Change-Id: I28013a4e331cfc6f01de873e80af48f765e49494
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Commit "net: zoap: Fix memory overflow issue" fixed and implemented
./well-known/core response in a different way, so this api is not needed
anymore.
Change-Id: I8f945fb5842028be50ecfdef95cbe5da3189a538
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If CoAP .well-known/core services list is bigger than single fragment
then current helper functions overwrites beyond fragment space. Which
corrupted whole stack. Right now sending response in multiple fragments
but preferred way is send response in block by block. This should
overcome packet loss across mesh scenarios. Recommended feature will
be supported with later patches.
Change-Id: I30ca55bde2516d80b3583731241ad295799c6614
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Most of the zoap utilities deal with first fragment of buffer chain.
So accessing of buf->frags directly make less usage of stack than
delcaring another variable for frag and its data. Due to code
refactoring couple of lines removed and in between those lines
coverity complained two issues, which is not valid now.
Coverity-CID: 157597
Coverity-CID: 157598
Change-Id: I3035c0625a131d49a4f0250ff0052875d3382544
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When net_ipv6_finalize_raw() inserts RPL(HBH) header after IPv6 header,
it updates IPv6 next header as HBH and HBH next header as original IPv6
next header.
Then net_ipv6_prepare_for_send() will update RPL HBH header if it exists.
But net_rpl_update_header() is comparing HBH option and IPv6 next header,
which is wrong. Wrong comparion does not update RPL instance id and
sender rank. Peer nodes drops all the packets due to invalid instance
ID and sender rank.
Change-Id: I91c1870a09c60f8e1ebc73e434dcc208caf6299a
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Following flow does not work:
net_context_get
net_context_bind
..
..
net_context_put
net_context_get
net_context_bind
At instance of call to net_context_bind, conn_handler
is not NULL and returns with EISCONN.
This patch sets conn_handler to NULL in net_context_unref
Change-Id: I56a50839101b22161644b3cd7c5f510fa1abae3e
Signed-off-by: Mitul Shah <mitul.a.shah@intel.com>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds net_buf_reset which can be used to reset the state of a buffer.
Change-Id: I4b7c89dfd1a23a2ec8dfa3c99d5b02b9bcbceef3
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix doxygen comment typos used to generate API docs
Change-Id: I3efff6f5fa26f87d1e658d6336fef01ce45f5bb0
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Use UNALIGNED_GET and UNALIGNED_PUT throughout the networking stack to
access fields from the IP address structure. These structures can be
mapped directly to buffers and the macros are required for correct
unaligned memory access.
Jira: ZEP-2012
Change-Id: I55f9da7b143a22fa869d5d215c661de988cd9b91
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
