It may be useful for the app to know what the initial NetKeyIndex that
it was given during provisioning is.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is in anticipation of soon adding health client support, which
could then cause confusion due to the ambiguous API names.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that there's support for configuration client as well, rename cfg
to cfg_srv to avoid any confusion.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some of the provisoning routines, such as node reset assume that we
have a valid bt_mesh_prov pointer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add the ability to track the provisioning bearer through an extra
parameter to link_open/close. Also introduce new public functions to
enable/disable specific provisioning bearers. This also means that one
now needs to explicitly enable provisioning bearers after calling
bt_mesh_init().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It is possible to access past end of url buffer by one byte.
Coverity-CID: 178790
Fixes#4784
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In http_request() a CRLF is added to the header information after
the protocol is added. 2 CRLF in a row means the header information
is done, so following header information will be ignored.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
All current socket samples as one of the points show portability to
POSIX platforms, and provide POSIX makefiles to let user build such
a version of application easily. These Makefiles were lost during
CMake conversion.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
KBuild would write the .inc file to the source directory, this was
changed during the CMake migration because whenever possible it should
be avoided to write files outside of the build directory.
But Makefile.posix assumes that these files are generated in the
source directory so we need to keep generating them there for now.
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Avoid applications defining empty model arrays by themselves by
documenting the BT_MESH_MODEL_NONE helper macro (renamed to be more
intuitive) and using it in the mesh sample app.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Update the sample README with the latest changes during the
1.10 development cycle. We removed the 2 concurrent IPv4
and IPv6 connections and now the sample will make a single
connection based on whatever is configured (currently IPv6
takes precedence over IPv4).
Added instructions for how to switch the sample to IPv4.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
The QEMU_NET_STACK is enabled automatically if building
a networking application to QEMU so no need to do it for
each networking sample.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Update the documentation for the Bluetooth samples not to refer to the
old style of building using make. Instead, simply refer to the general
instructions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Rename netusb project file to be more general and support sanity build
for 96b_carbon board.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Create http library that uses net-app instead of net_context
directly. The old HTTP API is deprecated.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This sample tesecase provides sample code :-
1. Triggers Low Power tasks into nrf52 SOC (CONST LAT and LOW PWR)
2. Triggers System Off state.
3. Wake up device through port Event by GPIO (Button 1).
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
This is similar fix as in commit 643cc4a22c but this one fixes
the thread parameter in UDP DTLS thread.
Fixes this function parameter datatype warning:
expected ‘k_thread_stack_t * {aka struct _k_thread_stack_element *}’
but argument is of type ‘u8_t * {aka unsigned char *}’
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The length and the start of the coap payload was not correct
because the received packet did not had IP and UDP header in place.
Fixes#4630
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This should clear up some of the confusion with random number
generators and drivers that obtain entropy from the hardware. Also,
many hardware number generators have limited bandwidth, so it's natural
for their output to be only used for seeding a random number generator.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Some "random" drivers are not drivers at all: they just implement the
function `sys_rand32_get()`. Move those to a random subsystem in
preparation for a reorganization.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Previously, post_write and execute callbacks returned 1 when handled
and 0 for error condition. However, this wasn't detailed enough and
the engine can't propagate any sort of error back to users -- so it
doesn't even check the return values in many cases!
Let's adjust the resource callback functions of all objects and the
lwm2m_client sample to return 0 for success or a valid error code.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Now that we can access resource data in the lwm2m subsys, let's use
the user provided firmware push buffer (5/0/0) to also store the
firmware pull data.
This way the size of the firmware pull buffer is completely up to the
application.
NOTE: This patch adds a 64 byte firmware buffer to the lwm2m_client
sample for this purpose.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Now that the LwM2M library can parse across multiple fragements,
let's remove the larger than normal buffer size setting.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Add configuration to http_server sample making it possible to work
with USB Device stack with Ethernet ECM protocol.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Given that 6lowpan/BLE support is still work in progress, uses
debugging interfaces to setup, has known issues, and otherwise
not widely known or adopted, provided detailed instructions,
including reasonable diagnosing steps on how to set up and test
such a connection.
Tested using 96b_carbon.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This reverts commit 1da0a9eebd.
The workaround caused a severe performance penalty, and only worked
for USB packets of 4-15 bytes in length (16+ byte packets weren't
subject to the hardware bug). Single-byte packets (very common for
cdc_acm serial port transfers) would still be duplicated sometimes.
The upcoming DMA implementation does not share the performance
penalty, and also is not subject to the bug for those sizes of packets
(though it DOES still have a problem with single-byte packets!).
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
If NET_L2_IEEE802154 and NET_IPV6 are enabled:
- NET_6LO is enabled
- NET_L2_IEEE802154_FRAGMENT is enabled
Thus removing setting this config options to yes where applicable.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is similar to the LPD8806 sample, but uses the WS2812 driver
instead. The app configuration is a bit more finicky, so try to
provide helpful references. This could be made more beginner-friendly
with the addition of timing diagrams, etc., but this should be enough
for an experienced developer to use.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This sample displays the colors red, green, and blue on consecutive
LEDs in an LED strip, moving the starting point where red begins
further down the strip at each time step. The color band wraps around
to the beginning when it reaches the end.
Since this is the first application in samples/drivers to have
documentation, add samples/drivers/drivers.rst as well, and include it
in the top-level toctree from samples/samples.rst.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Remove CONFIG_NET_L2_ETHERNET, as it's automatically set by the
board. This effectively makes prj_frdm_k64f.conf fairly portable,
e.g. the same config can be used for frdm_kw41z whcih uses 802.15.4
connectivity instead.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
LwM2M is intended for constrained devices. The default samples
settings are quite large by that standard and can be reduced to
reflect actual usage.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
After the LwM2M sample was introduced several HW related defaults were
added to Kconfig. We no longer need separate prj*.conf files for K64F
and qemu_x86. Let's combine them into a single prj.conf file and
adjust documentation.
NOTE: This also adjusts README.rst
Signed-off-by: Michael Scott <michael.scott@linaro.org>
We removed the default values for:
* CONFIG_USB_DEVICE_VID
* CONFIG_USB_DEVICE_PID
So put some dummy values in the sample.yaml to get things building
again.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fixes this function parameter datatype warning:
expected ‘k_thread_stack_t * {aka struct _k_thread_stack_element *}’
but argument is of type ‘u8_t * {aka unsigned char *}’
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The relay functionality was supposed to be always enabled rather than
always disabled on the micro:bit.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The IEEE 802.15.4 UART pipe config files in
echo_server/prj_qemu_802154.conf and echo_client/prj_qemu_802154.conf
did not had proper configuration options set. This prevents
qemu<->qemu communication between the echo-server and echo-client.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use platform_whitelist to specify supported boards to make sure
mem_domain_apis_test sample will be built during sanitycheck.
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
Vendor ID and Product ID should be assigned on build time by
respective process.
For sanity check we assign some random values which are only used for
build tests and should not be used for real products.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
It's been observed that that the relay toggling functionality is not
very useful, and that it's better left enabled always. Change the
purpose of the second button to instead modify the target address that
messages sent through the first button get directed to. By default the
destination is the group address, i.e. all nodes receive the message.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This sends out 2KB+ payload (i.e. guaranteedly more than 1 network
packet). When this sample was initially written, using such payload
quickly let to a deadlock somewhere in the network stack. However
as of now, running with such payload can sustain testing with
"ab -n10000" (10000 consecutive HTTP requests using Apache Bench),
so set is as a default, to serve as a mark point against possible
future regressions.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Applications may want to be notified when various events
happen in the LwM2M rd client. Let's implement an event
callback which sends: connect, disconnect and update events.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
1. Add handling block1 option in handle_request(). The basic idea is
to declare structure block_context at compiled time and use "token"
as a key to pick up the on-going block cotext. It should be able to
support multiple blockwise transfer concurrently
2. Use write callback implemented in lwm2m_obj_firmware to deal w/ the
update state transition and than call the callback registered by the
application
3. move default_block_size to lwm2m_engine.c to share between
lwm2m_engine and lwm2m_obj_firmware_pull
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: rebased on LwM2M net_app changes.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
1. Parse firmware pull URI
2. Add lwm2m_firmware_get/set_update_cb() for application to register
callback. This is because we want to check the update_state before
we pass to the application
3. Add lwm2m_firmware_get/set_update_result() and
lwm2m_firmware_get/set_update_stat() to manage the state transition
as well as the sanity check
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: rebased on net_app framework and
lwm2m_message refactoring.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This application does not do anything itself, it just waits
mDNS queries and responds to them.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Previously, there was boolean CONFIG_SLIP_DEBUG, which effectively
switched between "logging off" and "debug-level logging". Instead,
switch to CONFIG_SYS_LOG_SLIP_LEVEL (the naming of the option follows
existing conventions) which allows to select any of the standard 5
logging levels.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Explicitly call net_pkt_ref()/net_pkt_unref() to avoid packet being
freed after calling net_context_sendto() at retransmit_request().
Also, do not return when net_context_sendto() returns error. Instead,
we should keep retrying.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Original coap_client implementation does not setup "appdatalen" of
net_pkt correctly and does not strip the IP + UDP headers when doing
the retransmit. This will result in malformed coap packet. Fix it by
adding a strip_headers() function to set appdatalen and get rid of
IP + UDP headers.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
This helps to debug issues with mass connection handling (e.g. when
issues happen at ~500th connection).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
1. After calling sendto(), the packet will be unreferenced.
Call coap_pending_cycle() to make sure the packet is referenced until
we got the response from the peer or retransmission timeout.
2. In retransmit_request(), we rearrange the order to avoid the issue.
3. Remove IPv4 configuration for source code is expecting IPv6
4. Correct a typo in README.rst
5. Initialize the interface w/ IPv6 address
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
When testing against etsi_coaptest.sh, test cases TD_COAP_BLOCK_03/04
will get stuck. This is because these testcases send out a blockwise
transfer but with an empty payload. Although this should be a legit
request, large-update/create handlers did not check "MORE" flag in
block1 option and always return an error when request comes with empty
payload.
Corrected as below
1. Initialize coap_block_context when first block arrives.
(SIZE1 option is not always available. In the case that SIZE1 is
unavailable, the zoap_block_context will be re-initialized each time
a new block has arrived)
2. Check "MORE" flag of block1 option. If it's the last block, then
an empty payload should be allowed.
3. Response w/ 2.04 CHANGED when the last block has arrived for
large-update
4. Response w/ 2.02 CREATE when the last block has arrived for
large-create
5. Remove adding block2 option to the response since we are not sending
back any data to the caller
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Keep the flash shell up to date with the latest flash driver updates.
- Get the driver name from soc.h
- Add a write_block_size command
- Implement flash_shell_page_layout() using flash_page_foreach()
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
At 32 bytes the snprintk call to fill the help buffer was most often
running out of room and returning an error. Let's expand it to 64.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Users can private message the bot and the bot should respond directly
back to that user rather than rudely ignoring them.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Let's create a static global var for nickname so that we can use it
later without having to pass it all the way through callbacks, etc.
Also limit the size to 16 bytes as IRC servers will truncate anything
beyond.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
These structures were originally intended to prototype an IRC library
which would be later moved into the subsys/net/lib/irc folder.
Unfortunately, that effort has faded and they make this code much more
complex than necessary. Let's remove them in favor of simplicity.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
For style points let's declare the text shown at the beginning
of main() function to the top of our source as APP_BANNER so that
it's obvious and presents nicely.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Let's simplify the parsing function which scans incoming traffic
for carriage returns and let the net_pkt_read() function cross
multiple buffers if needed. Also, gracefully skip lines which
are longer than the command buffer.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Some L2 layers such as bluetooth need to have extra buffer pools to
hold copies of packets for use with TCP. Let's add support for that
so that future enablement of other boards won't get bitten.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Let's migrate from using NET_LOG_* functions to the SYS_LOG
facility which allows for granular control over the display
of info, debug and error messages unique to the file that
you're in.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Let's remove all of the extra coding to handle DHCP, DNS and event
management. This is all handled by the net_app API.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
It's useless now, arduino_101 has proven not working very well with x86
gpios and CC2520 never got to work properly there.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Only ieee802154 should have been using it, but it ended in various
samples that did not require it anymore once they've been using
net_app. Unlike former samples settings, net_app settings are tied to
net_app, so let's just forget about all of it and silently use net_app.
If something goes wrong in setting net options, it will be a unique
place.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This app now depends on net_app API, so it must be enabled for all
project configs we have.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
From section 3.4.5.3 in the Mesh Profile Specification 1.0:
"A node shall implement a Local Network Interface."
Removing the Kconfig option also helps clean up quite a lot of code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The code was causing only one byte of data to be placed in timeout
instead of sizeof(timeout) as intended.
Coverity-CID: 170744
Fixes#4057
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's dumb, because it doesn't really parse HTTP request, just always
sends the same page in response. Even such, it's useful for socket
load testing with tools like Apache Bench (ab) and for regression
checking in the net subsystem.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
CONFIG_NET_L2_BT_ZEP1656 shall only be used with hosts that are known to
not comply with RFC 7668.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CONFIG_NET_APP_BT_NODE is required in order for the Bluetooth L2 driver
to register IPSS service.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Composite multifunction USB devices should be able to know about
configuration change, implement it through existing callback.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
