Rather than redefining a macro which might be generated we should create
a new define name that should get used in the code. Replace redefining
DT_ALIAS_LED0_GPIOS_* and just use the LED_GPIO_* defines that already
exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove DT_ADC_{0..2}_NAME from dts_fixup.h, if this casues the
dts_fixup.h file to be empty we remove the file as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix BT_LE_CONN_OPT_NONE renamed to BT_CONN_LE_OPT_NONE missed in 2
places in conn.h
Regression from commit: fdb3da8aff
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Get rid of legacy timeout API and move to new timeout API for LoRa.
This involves changes to API, SX1276 driver and sample application.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
The LoRa APIs are expected to undergo some change as the usecase get's
increased. So let's mark it as experimental until the APIs got
stabililized.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
The RTC/Counter implementation doesn't fit for the upcoming LoRaWAN
as most of the Counter drivers in Zephyr works with 1s granularity
which is not enough for LoRaWAN stack. So, k_timer calls are used in
place of Counter's alarm and k_uptime_get() APIs are used in place of
Counter's time keeping.
While at it, lets also fixup the broken alarm implementation.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
fix bss section be copy to binary.
When compiling with non-xip.
All sections will be placed in the ram.
If NOBITS section isn't placed at the end of ram,
objcopy will placed these section to binary file.
The modify only for no-userspace.
In userspace the section will be adjust,
kobject_data size increase,
the bss be shifted, the content of kobject_data
will no mactch to kernel obj of bss.
Signed-off-by: Frank Li <lgl88911@163.com>
Reworked sam_gmac driver to get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from soc_pinmap.h that are no longer needed due to
getting all that information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The OpenOCD JTAG reset causes the SAM E54 SoC to prematurely start code
execution before the SoC is ready, and this causes hard faults when the
MPU is enabled -- causing OpenOCD to hang.
This commit disables the JTAG SRST reset mechanism and falls back to
using the Cortex-M SYSRESETREQ emulation reset mechanism, which does
not have experience this issue.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the ARM memory protection unit for the SAM D54
Xplained Pro board, since `CPU_HAS_ARM_MPU` is now selected by the SoC
Kconfig.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The Atmel SAM D5x and E5x series SoCs include the ARM memory protection
unit that supports up to 8 memory regions.
This commit adds the missing device tree MPU node to `samd5x.dtsi`,
which is used by both the SAM D5x and E5x series SoCs.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the `devicetree.h` header inclusion in the Atmel SAM-
family SoC header files, as required by the ARM SoC conventions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the `devicetree.h` header inclusion in the Atmel SAM0-
family SoC header files, as required by the ARM SoC conventions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Remove the BT_LE_CONN_OPT_2M option and update documentation.
This was a misunderstand about the init PHY HCI parameter.
The init PHY in the extended connection create command does not
determine which PHYs are accepted as the initial PHY of the
connection. This is instead determined by the secondary PHY of the
extended advertiser.
The init PHY parameter only specifies which conn parameters are
provided, and since we only provide one conn parameter this option
has no effect.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This configures the nucleo_f411re board for testing the SPI loopback
with DMA V1 transfer. DMA instance 2 is used.
This test requires pin SPI_A_MISO (D12) to be connected
to pin SPI_A_MOSI (D11) on the nucleo_wb55rg boardtest dma_V1
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This configures the nucleo_l476rg board for testing the SPI loopback
when with DMA transfer.
It requires pin MOSI to be connected to pin MISO of the SPI1
SPI tx/rx are assigned to the request ID 1 of dma1 channels 3 and 2
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patch is defining the DMA1 & 2 for the sm32l4 series
with 7 channels and support of mem2mem transfers
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds a new testcase in the spi_loopback test application
to use several buffers for the DMA transfer.
It requires the MOSI to be connected to the MISO of the SPI1.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This changes the spi_loopback test application to use the DMA transfer.
In case of DMA, some testcases are useless.
It requires the MOSI to be connected to the MISO of the SPI1.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This includes the dma cells as client for the spi
An example of the client part is defined in the dma.yaml
Consequently, bindings for the dmas property becomes then 'not required'
Including dma.yaml is not needed as dma properties
are now part of base.yaml
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The DMA callback function now controls the tx or rx buffers
and reload dma in case of multiple trnasfer before the transfer ends
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Enable dma operations with or w/o a dmamux on STM32
for SPI periph/memory operations.
Use the pi dma client with dma macros
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patch is disabling the dma channel before reloading
source and dest for memory and peripheral addresses
Then the channel is enabled to re-launch the transfer.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit enables the QEMU icount mode for `mps2_an521`, in order to
decouple the host clock from the emulated guest clock.
This prevents guest timing instability from causing test failures when
the host CPU load is very high.
The icount `shift` value of 7 was empirically chosen to allow the tests
to complete in both realistic and reasonable amount of time.
The following are quick notes on the parameters used:
* -icount shift=7: Execute one instruction every 128ns of virtual time
* -icount align=off: Do not synchronise the host and guest clocks
* -icount sleep=off: Advance virtual time without sleeping/waiting
* -rtc clock=vm: Isolate the guest RTC time from the host
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert DT_UART_{0,1}_NAME to DT_NODELABEL() references as the cases are
board specific and this allows us to remove DT_UART_{0,1}_NAME defines
in dts_fixup.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When files were added, matching did not work and we were counting added
files twice. Use sets to make sure we have a unique list of files.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Zephyr has not committed to complying with the upstream requirement
that the SPDX declaration be on the first line of a file, so disable
the warning.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
native_posix supports for some time now generating a 64bit
binary with the native_posix_64 target, but we never got
to document it.
Add a section describing it, and correct the WSL1
note/warning (also with a link with instructions on how to hack
WSL1 to make it run 32 bit binaries)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Fixes: #24903
This commit now includes ${ZEPHYR_BASE}/cmake/python.cmake to locate
python3.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Replace:
DT_FLASH_ERASE_BLOCK_SIZE ->
DT_PROP(DT_CHOSEN(zephyr_flash), erase_block_size)
DT_FLASH_WRITE_BLOCK_SIZE ->
DT_PROP(DT_CHOSEN(zephyr_flash), write_block_size)
As this allows us to phase out the old generator.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Currently there are no test for openthread on zephyr.
Created tests for OpenThread platform radio interface.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
I was missing mocking api to compare data under an address pointed
by a parameter as some functions may copy buffers before passing
further.
Created ztest_expect_data and ztest_check_expected_data.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
The last parameter to hci_cmd_done() is expected to be a valid net_buf
since the function immediately tries to dereference it. Fix this by
passing the appropriate buffer reference to the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Options summary:
-icount shift=5: Execute one instruction every 32ns of virtual time
-icount align=off: Do not synchronise the host and guest clocks
-icount sleep=off: Advance virtual time without sleeping/waiting
-rtc clock=vm: Isolate the guest RTC time from the host
64-bit still has some issues that are being looked at.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We did not have any reference to queues and doxygen information were not
linked correctly. Add a placeholder and pull in doxygen data so whenever
someone adds a reference, a link is created.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Replace having dts_fixup.h files define DT_ADC_{0..2}_NAME with using
the new devicetree.h macros. We test to see what driver compat is
enabled via DT_HAS_COMPAT and set DT_DRV_COMPAT to that compat. Than we
can utilize the DT_INST_LABEL() macro to extract the name of the device.
We also replace the Kconfig ADC_{0..2} symbols with DT_HAS_DRV_INST.
This will allow us to remove those Kconfig symbols as this was the only
usage.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Linux uses for_each in macros that produce loops; Zephyr uses
FOR_EACH. Update the corresponding checks to match Zephyr's spelling.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
