Using find_package to locate Zephyr.
Old behavior was to use $ENV{ZEPHYR_BASE} for inclusion of boiler plate
code.
Whenever an automatic run of CMake happend by the build system / IDE
then it was required that ZEPHYR_BASE was defined.
Using ZEPHYR_BASE only to locate the Zephyr package allows CMake to
cache the base variable and thus allowing subsequent invocation even
if ZEPHYR_BASE is not set in the environment.
It also removes the risk of strange build results if a user switchs
between different Zephyr based project folders and forgetting to reset
ZEPHYR_BASE before running ninja / make.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This is joint work with Kumar Gala (see signed-off-by).
Document the changes to the generated node macros in macros.bnf,
moving the old file to legacy-macros.bnf and putting it in its own
section.
The actual generated macros are now a low-level detail, so rewrite the
foregoing sections as examples in terms of the new <devicetree.h> APIs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We rename the nRF51 Dev Kit board target (nrf51_pca10028)
to nrf51dk_nrf51422. We update all associated references
in the supportive documentation and all nRF51-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Allocates segmented message buffers as slabs in a common pool for RX and
TX. This reduces memory requirements for both TX and RX, as TX messages
can be stored without the network and advertising buffer overhead, and
RX can use only the slabs it needs, instead of allocating a full size
segmented message. This approach also removes the need for decrypting
the segments for each retransmission, reducing overall processing load.
Slab based segmentation for tx also introduces queuing of segmented
messages, which allows the application layer to send multiple messages
to the same destination without violating Bluetooth Mesh specification
v1.0.1, section 3.6.4.1. This mechanism is provided through a flag that
blocks segmented messages to a destination which a message is already
being sent to until the previous message finishes.
This changes the SDU size configuration to a symmetrical
RX_SEG_MAX/TX_SEG_MAX pair of configurations, plus a new segment pool
side configuration. It also removes the binding between the TX_SEG_MAX
config and the advertising buffers, reducing the minimum advertising
buffer count from 6 to 3.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Name all subsystem reference consistently with an '_api' postfix and
clean up naming and folder structure in some cases.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Remove data length and phy update set to 'n' on board that does not
support these features anyway. BT_CTLR_DATA_LEN_SUPPORTED and
BT_CTLR_PHY_UPDATE_SUPPORTED are both set to 'n'.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Remove BT_CTLR_DTM_HCI=y config which is not supported for this board.
This produced the following warning:
warning: BT_CTLR_DTM_HCI was assigned the value
'y' but got the value 'n'. Check these unsatisfied dependencies:
BT_CTLR_DTM_HCI_SUPPORT (=n).
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Refactor conf files to use prj.conf + board/<board>.conf configuration.
This allows us to have put common configurations into the prj.conf and
have board specific configs in each board file.
This also respects adding additional prj.conf files such as
-DCONF_FILE='nrf5.conf debug.conf' to add debug configuration.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Update main stack size for nrf5 boards. This is to support an
alternative hci_driver that has a higher stack size usage in hci driver
open. Measured stack usage in this case to 808/1024.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This sample has nrf51_pca10028 on its platform_whitelist but lacks
configuration and overlay files that would make it possible to build
this sample for that board. This commit provides such files.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Handle connected callback with error status not releasing the default
conn object in central samples. This can happen when the initiator fails
to create the connection within 3 seconds and is canceled by the host.
Also restart the scan role in this case.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The one page on devicetree is too long. Split it into multiple pages
to make it easier to digest and more squintable. This is basically
just moving content around; minimal changes have been made apart from
redoing some transitions and adding a couple of introductory paragraphs.
Rename the 'device-tree' Sphinx :ref: target while we are here.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The default DTS of VEGABoard does not enable the necessary nodes
for the SW LL to function; as such an overlay is needed for
each sample that is intended to be run on the VEGABoard. Some
of the samples miss this overlay so this patch adds them.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
The existing stack_analyze APIs had some problems:
1. Not properly namespaced
2. Accepted the stack object as a parameter, yet the stack object
does not contain the necessary information to get the associated
buffer region, the thread object is needed for this
3. Caused a crash on certain platforms that do not allow inspection
of unused stack space for the currently running thread
4. No user mode access
5. Separately passed in thread name
We deprecate these functions and add a new API
k_thread_stack_space_get() which addresses all of these issues.
A helper API log_stack_usage() also added which resembles
STACK_ANALYZE() in functionality.
Fixes: #17852
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
VEGABoard BLE controller implementation supports HCI over UART;
as such enable this configuration when building the hci_uart
sample.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
The DIS service requires BT_SETTINGS otherwise it will not have a
settings handler. Instead DIS will only use Kconfig to set it's
values.
Fixes: #22478
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Update bluetooth hcp_spi sample to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Introduce define for dt generated gpio flags
- Update 96b_carbon_nrf51.dts according to new bindings
- Gpio IRQ pin is configured to output inactive
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
BT_DEBUG is a promptless helper symbol, defined in
subsys/bluetooth/common/Kconfig. It is selected by BT_DEBUG_LOG, which
these configuration files also enable.
Flagged by https://github.com/zephyrproject-rtos/zephyr/pull/20742.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add support for requesting an inverted PWM pulse (active-low) when
setting up the period and pulse width of a PWM pin. This is useful
when driving external, active-low circuitry (e.g. an LED) with a PWM
signal.
All in-tree PWM drivers is updated to match the new API signature, but
no driver support for inverted PWM signals is added yet.
All in-tree PWM consumers are updated to pass a flags value of 0
(0 meaning default, which is normal PWM polarity).
Fixes#21384.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The TCP code expects that we know when the socket has called accept()
in order to continue connection attempt.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
By this commit user gets possibility to register USB
device satutus callback. This callback represents device state
and is added so user could know what happend to USB device.
Callback is registered by providing it to usb_enable()
USB api is extended by this callback handler.
Samples using using USB are by default provide no callback
and the usb_enable() is called with NULL parameter.
Status callback registered by hid class is deleted as now
USB device has global callback for all classes within device.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This commit provides a sample dummy application demonstrating
the usage of the added dynamic Tx power control over the HCI
commands and HCI interfaces.
Signed-off-by: Andrei Stoica <stoica.razvan.andrei@gmail.com>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Split Link Layer implementation uses 80 bytes more ISR stack
in comparison to Legacy Link Layer, hence increase the
required ISR_STACK_SIZE for the BBC micro:bit and other
nRF51 QFAA SoC based mesh and mesh_demo samples.
Fixes#20414.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This sample demonstrates BLE peripheral for ST BLE Sensor.
You can test button notification and LED service using
ST BLE Sensor Android application
Signed-off-by: Marcio Montenegro <mtuxpe@gmail.com>
Removes redundant and invalid configurations from the bluetooth/mesh
sample. Removes some stale disabled config entries.
Fixes L2CAP related warning in config step of sample.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Switch to using the synchronous bt_init call before starting the main
loop in the peripheral samples. This is to avoid sending notifications
before bluetooth has been properly initialized.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This define is not of use anymore since there's a global net_buf user
data Kconfig variable and its definition already guarantees a
sufficient minimum for Bluetooth.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix scanning so that we always use active scanning in case the UUID we
are looking for is in the scan response, and disable duplicate filtering
to handle devices that modify their advertising data at runtime, such as
smartphones reacting to apps being opened and closed.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix build reply function. The sample uses return value
from net_pkt_read() to determine data length,
but the return value is 0 on success.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add a special target that's marked build_only so the BLE SW LL
implementation on VEGABoard is built daily. This helps ensuring
that it doesn't get inadvertedly broken by subsequent updates.
The name of the target is peripheral_hr_rv32m1_vega_ri5cy
and it can be run with the following command:
sanitycheck -v --all -p rv32m1_vega_ri5cy \
-x=CMAKE_REQUIRED_FLAGS=-Wl,-dT=/dev/null \
--test samples/bluetooth/peripheral_hr/\
sample.bluetooth.peripheral_hr_rv32m1_vega_ri5cy
Note: The extra CMake flags are required if running with the official
VEGABoard compiler, due to this linker issue:
https://github.com/pulp-platform/pulpino/issues/240
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Add the required specific HW configuration for SW defined
BLE LL on RV32M1 SoC, by means of DTS overlays:
- enable INTMUX0 channels 2 & 3
- route Generic FSK RF0 interrupt to INTMUX channel 3
- route LPTMR1 interrupt to INTMUX channel 2
This change is done for all Bluetooth samples that are intended to
run on RV32M1 using BLE SW LL.
Signed-off-by: George Stefan <george.stefan@nxp.com>
Signed-off-by: Radu Alexe <radu.alexe@nxp.com>
Signed-off-by: Ionut Ursescu <ionut.ursescu@nxp.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Adds the model extension concept to the access layer, as described in
the Mesh Profile Specification, Section 2.3.6. Extensions are
implemented as a tree, using two pointers in each model:
The extends pointer points to the first extended model, and the next
pointer points to the next sibling or (if the NEXT_IS_PARENT flag is
set) the parent model in the tree, forming a cyclical "Left-child
right-sibling" (LCRS) tree. The tree root can be obtained by calling
bt_mesh_model_root_get(), and the extended models can be walked by
calling bt_mesh_model_tree_walk().
According to the Mesh Profile Specification Section 4.2.3, all models in
the same extension tree share one subscription list per element. This is
implemented by walking the model's extension tree, and pooling the
subscription lists of all models in the same element into one. If the
config server adds a subscription to a model, it may be stored in any of
the model tree's models' subscription lists. No two models in the same
extension tree and element will have duplicate groups listed. This
allows us to increase extended models' capacity for subscriptions
significantly.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Key overwrite feature allows to overwrite old pairing key
records when key storage is full and a new pairing request occurs,
or new keys are distributed. If enabled when key storage is full and
a keys storage slot is requested, the oldest keys added will be
removed. So new devices can be paired with no limitations and no need
to determine, which devices should be unpaired to free key storage
space explicitly in application. To enable the feature set
CONFIG_BT_KEYS_OVERWRITE_OLDEST=y.
Oldest keys are determined by minimum value of up-counting aging
counter. If you set CONFIG_BT_KEYS_SAVE_AGING_COUNTER_ON_PAIRING=y
aging counter values will be updated each time the secure connection
is established. This might increase flash wear out if at least two
secure connections are established and shut down periodically. When
the option disabled aging counter is still updated on each new secure
connection, but not stored to flash.
Signed-off-by: Sergiy Nikolayenko <sergiy_nikolayenko@jabil.com>
The Peripheral Device Information Service (DIS) sample implements it's
own custom settings backend in order to load runtime settings.
This results in errors when the BT stack tries to save entries through
the custom handler since no save handler exists.
Error messages:
- bt_settings: Failed to save ID (err -2)
- bt_gatt: Failed to save Database Hash (err -2)
Since this is not a sample of how to do custom settings backend it is
best simply to remove using the custom backend, as it is not required
in order to load runtime settings.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
samples/bluetooth/peripheral couldn't build on nucleo_f429zi
since settings dependency on flash erase bock size.
On this series, flash erase are done per sector with sector
having varying size, so erase block size can't be used directly.
This has to be sorted, but for now nucleo_f429zi is removed from
sample withelist to unlock CI.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Re-run with updated script to convert integer literal delay arguments
to k_thread_create and K_THREAD_DEFINE to use the standard timeout
macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DTSpec writes this as a single word, presumably to make it easier to
grep for / more precise. Follow along in the rest of the docs now that
our main DT docs page agrees with this usage.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
This option determines the name under which the device represented by
the `sw_pwm` node is registered in the system. But when the value of
this option does not match the `label` property of the `sw_pwm` node,
a problem arises when the `sw_pwm` node is referenced by a "pwm-leds"
compatible node, since the `*_PWMS_CONTROLLER` macro that is generated
for this referencing node contains a non-existing device name (as it is
the `label` property value, not the Kconfig option value).
This commit solves the issue described above by removing the Kconfig
option and replacing all of its occurrences in sample applications
by the standard macro generated for the `sw_pwm` node, containing
the value of the `label` property of this node.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit implements generic function to decide
witch functions to call for selected value name with given
loading parameters.
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
This commit allows loading data from settings permanent storage
directly to the given callback function.
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
This adds support to set different permissions to CCCD so security can
be checked when enabling notification which conforms to:
BLUETOOTH CORE SPECIFICATION Version 5.1 | Vol 3, Part G page 2360:
'3.3.3.3 Client Characteristic Configuration
Authentication and authorization may be required by the server to
write the configuration descriptor.'
In addition to that also ensure that notification are not re-enabled
until the proper security level is reached to conform to the following
statement:
'10.3.1.1 Handling of GATT indications and notifications
A client “requests” a server to send indications and notifications
by appropriately configuring the server via a Client Characteristic
Configuration Descriptor. Since the configuration is persistent
across a disconnection and reconnection, security requirements must
be checked against the configuration upon a reconnection before
sending indications or notifications. When a server reconnects to a
client to send an indication or notification for which security is
required, the server shall initiate or request encryption with the
client prior to sending an indication or notification. If the client
does not have an LTK indicating that the client has lost the bond,
enabling encryption will fail.'
Fixes#17983
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Removes the special stack config setting in the Bluetooth Mesh sample to
allow it to run with other Bluetooth controllers.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Renames the nrf51_blenano config file to something generic and uses that
same config for the nrf51_ble400 board, which has the same constraints.
Cannot rely on the CONFIG_SOC_NRF51_QFAA variable, as the CONF_FILE
variable must be set before the boilerplate.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Rename AUTHENTICATION, to AUTH, since this is a well established short
form of the word.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename bt_conn_security to bt_conn_set_security, this makes the API
naming more consistent.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename security level enum, using level and number instead of low,
medium, high and fips.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add security error to security_changed callback. Call this callback when
security has failed and provide current security level and error.
Reason for failure can be.
- Pairing procedure failed, pairing aborted before link encryption.
- Link encrypt procedure failed
- Link key refresh procedure failed.
Fix missing bt_conn_unref on encryption key refresh with error status.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This removes the necessity of registering the storage for CCC and make
it part of the declaration itself.
Fixes#18547
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reduce the RAM usage in two of the Bluetooth samples in order for them
to fit in the BBC Microbit's RAM.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Error codes are listed in header files and in the core spec as hex
values. Always print them in hex in debug for easier error code
checking.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Delete IPSP sample file, this source file is not included in any build
files. The service contains no valuable logic other than advertising
with the IPSP service in the advertising data.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move the HID over GATT service into the sample that demonstrates it.
This avoids long build paths
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move the Current Time service into the sample that demonstrates it.
This avoids long build paths
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move the health thermometer service into the sample folder that
demonstrates it. This avoids long build paths
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This commit moves the BLE GATT heart rate service from
samples/bluetooth/gatt to subsys/bluetooth/services and adds a Kconfig
entry to enable and configure the service.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This commit moves the BLE GATT Battery service
from /samples/bluetooth/gatt to /subsys/bluetooth/services and
adds a Kconfig entry to enable and configure the service;
when enabled, it will register itself automatically.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Tick rate is becoming a platform tunable in the tickless world. Some
apps were setting it due to requirements of drivers or subsystems (or
sometimes for reasons that don't make much sense), but the dependency
goes the other way around now: board/soc/arch level code is
responsible for setting tick rates that work with their devices.
A few tests still use hard-configured tick rates, as they have
baked-in assumptions (like e.g. "a tick will be longer than a
millisecond") that need to be addressed first.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Adding Health Thermometer Service sample. Refer to Health Thermometer
Profile Specification for detailed information about the Health
Thermometer Profile.
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Introduce a separate buffer pool for events which the HCI driver
considers discardable. Examples of such events could be e.g.
Advertising Reports. The benefit of having such a pool means that the
if there is a heavy inflow of such events it will not cause the
allocation for other critical events to block and may even eliminate
deadlocks in some cases.
Also update all mesh samples not to specify explicit RX buffer counts
anymore. Instead, create appropriate defaults in Kconfig so that we
only need to override this in the app for cases like the bbc:microbit
with limited memory.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We use the following commands to rename any
SW._GPIO_{CONTROLLER,PIN,FLAGS} to
DT_ALIAS_SW._GPIOS_{CONTROLLER,PIN,FLAGS}
git grep -l SW._GPIO_CONTROLLER | xargs sed -i 's/SW\(.\)_GPIO_CONTROLLER/DT_ALIAS_SW\1_GPIOS_CONTROLLER/g'
git grep -l SW._GPIO_PIN | xargs sed -i 's/SW\(.\)_GPIO_PIN/DT_ALIAS_SW\1_GPIOS_PIN/g'
git grep -l SW._GPIO_FLAGS | xargs sed -i 's/SW\(.\)_GPIO_FLAGS/DT_ALIAS_SW\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
move misc/stack.h to debug/stack.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/printk.h to sys/printk.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/byteorder.h to sys/byteorder.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move spi.h to drivers/spi.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pwm.h to drivers/pwm.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_.*_GPIO_{CONTROLLER,PIN,FLAGS} ->
DT_.*_GPIOS_{CONTROLLER,PIN,FLAGS)
Used the following commands to make these conversions:
git grep -l DT_.*_GPIO_CONTROLLER | xargs sed -i 's/DT_\(.*\)_GPIO_CONTROLLER/DT_\1_GPIOS_CONTROLLER/g'
git grep -l DT_.*_GPIO_PIN | xargs sed -i 's/DT_\(.*\)_GPIO_PIN/DT_\1_GPIOS_PIN/g'
git grep -l DT_.*_GPIO_FLAGS | xargs sed -i 's/DT_\(.*\)_GPIO_FLAGS/DT_\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Assert if the UART device is NULL to help with debugging whenever
there's an issue locating the correct UART instance.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use Device Tree,and in particular a new 'bt-c2h-uart' to select which
UART is being used to communicate with an external BLE Host when acting
as a Controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The assumption that the value handle is one past the attribute handle
works for Zephyr servers but may not be true for others. Avoid the
hard-coded system-specific assumption.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This updates all client modules to const char processing of
setting names.
Update of peripheral_dis sample
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>