Key overwrite feature allows to overwrite old pairing key
records when key storage is full and a new pairing request occurs,
or new keys are distributed. If enabled when key storage is full and
a keys storage slot is requested, the oldest keys added will be
removed. So new devices can be paired with no limitations and no need
to determine, which devices should be unpaired to free key storage
space explicitly in application. To enable the feature set
CONFIG_BT_KEYS_OVERWRITE_OLDEST=y.
Oldest keys are determined by minimum value of up-counting aging
counter. If you set CONFIG_BT_KEYS_SAVE_AGING_COUNTER_ON_PAIRING=y
aging counter values will be updated each time the secure connection
is established. This might increase flash wear out if at least two
secure connections are established and shut down periodically. When
the option disabled aging counter is still updated on each new secure
connection, but not stored to flash.
Signed-off-by: Sergiy Nikolayenko <sergiy_nikolayenko@jabil.com>
This commit moves the BLE GATT heart rate service from
samples/bluetooth/gatt to subsys/bluetooth/services and adds a Kconfig
entry to enable and configure the service.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This commit moves the BLE GATT Battery service
from /samples/bluetooth/gatt to /subsys/bluetooth/services and
adds a Kconfig entry to enable and configure the service;
when enabled, it will register itself automatically.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
GATT long messages require buffers to store multiple packets. The actual
configuration for the bluetooth peripheral sample defines only two
buffers to store these messages. As the default ATT payload size is
18 bytes, the maximum payload size for a long ATT message is 36 bytes.
As the variable `vnd_long_value[]` has a defined size of 74 bytes, it
cannot be fully modified due to the 36 bytes limitation.
Set CONFIG_BT_ATT_PREPARE_COUNT=5 so all the maximum payload size goes
to 90 bytes and all the 74 bytes can be written to `vnd_long_value[]`.
Signed-off-by: Joao Cordeiro <jvcc@cesar.org.br>
This commit moves the BLE GATT Device Information service
from /samples/bluetooth/gatt to /subsys/bluetooth/services and adds
a Kconfig entry to enable and configure the service;
when enabled, it will register itself automatically.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
This force CONFIG_BT_DEVICE_NAME_MAX to be set even in boards where
CONFIG_BT_SETTINGS won't be defined so it exercise such configuration.
In addition to that set a long name that would not fix in the
ScanData.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Introduce a basic skeleton for peristent storage based on the settings
subsystem. Also enable support for this to the peripheral sample
application, so the new code gets exersized by CI. For now, the
implementation provides the same level support as the bt_storage API
ever did, i.e. for the identity address and the IRK.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
GAP is mandatory service and now that the db can only be build
dynamically there is no reason to keep the applications registering it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Removes CONFIG_BLUETOOTH_GATT_DYNAMIC_DB in preparation to the
introduction of bt_gatt_unregister.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Instead of using a hard-coded string, make the sample use the Kconfig
variable for the device name.
Change-Id: Ib09f594e1cba221f9064318572bd90d38bd2733a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Restructure the Bluetooth options more logically.
- Both host and controller are now behind the same high level
CONFIG_BLUETOOTH.
- Selecting controller support disables other HCI driver selection, so
the controller isn't in the same list as HCI drivers any more.
- Under the top-level there's a "Custom stack" option, which when
enabled opens up the option of choosing CONFIG_NBLE.
There are various other cleanups and simplifications in this patch as
well, since splitting these up would have been fairly tricky while
making sure all test cases still build.
Change-Id: I5bb715cb9d20201cb8b72fbd149c8a09a4b2d7d2
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
CONFIG_ARC_INIT defaults to 'n' now days so there's no reason to try
to explicitly disable it in the sample config files.
Change-Id: I88df06ba23bdac697f0767384f7b88e3bd9fced9
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Setting CONFIG_ARC_INIT=n in prj.conf make it possible to use same
config for both QEMU and Arduino 101 targets.
Change-Id: Ie4f549d5721f2b87077fba8787f5b1e2a8f07680
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
This adds a buffer for incoming prepare writes which can be
tunned using BLUETOOTH_ATT_PREPARE_COUNT, these buffers are then used in
execute write to commit the data thus making flush callback obsolete:
[bt] [DBG] bt_att_recv: (0x001159c0)Received ATT code 0x16 len 50
[bt] [DBG] att_prepare_write_req: (0x001159c0)handle 0x0022 offset 0
[bt] [DBG] prep_write_cb: (0x001159c0)handle 0x0022 offset 0
[bt] [DBG] bt_att_recv: (0x001159c0)Received ATT code 0x16 len 34
[bt] [DBG] att_prepare_write_req: (0x001159c0)handle 0x0022 offset 45
[bt] [DBG] prep_write_cb: (0x001159c0)handle 0x0022 offset 45
[bt] [DBG] bt_att_recv: (0x001159c0)Received ATT code 0x18 len 2
[bt] [DBG] att_exec_write_req: (0x001159c0)flags 0x01
[bt] [DBG] write_cb: (0x001159c0)handle 0x0022 offset 0
[bt] [DBG] write_cb: (0x001159c0)handle 0x0022 offset 45
Change-Id: Iae071d7b4b5b042285952da57e3f7a853cf58afb
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This add CONFIG_BLUETOOTH_DEBUG_LOG which depends on SYS_LOG since the
later can actually use either CONFIG_PRINTK or CONFIG_STDOUT_CONSOLE.
Change-Id: Ib2974d1331f6c91d119a218ec95e8bf01069377b
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This prepares for adding other debug types besides the printf-style
logging to the console.
Change-Id: Ic2ed305192491734da991c4f61fdaace03fd60f2
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add initial support for the Privacy Feature, including the ability to
manage a local IRK and to use Resolvable Random Addresses.
Change-Id: I1c70aea67078dd2a5d07f3b797c37746ebe9ab61
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
TinyCrypt provides implementation of AES CMAC so there is not need
for internal implementation in SMP code.
Change-Id: I15fe0daf8fca8c44b002636983b46502419c57a5
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
sys_rand32_get appears to get stuck with same number for a while so
instead just increment the heart rate by 1 until 160 and then return it
back to 90.
Change-Id: I2aea870c68539271a1bb6190a958a7e2d1914dc3
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add a single option for enabling use of TinyCrypt library for
crypto. This option selects all required TinyCrypt options
depending on BT features enabled. Thanks to this applications
only need to select single option instead of set of required
TinyCrypt features.
Change-Id: I2862e9ad3e204635f2ed3199433982bcfb7112f6
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
There is no need to keep arch specific prj.conf for these samples are
they are always the same.
Change-Id: I0f93b5a47458f9800a6654cc45914b911b42b3e3
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2016-02-05 20:25:20 -05:00
Renamed from samples/bluetooth/peripheral/prj_x86.conf (Browse further)
