This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
When tickless is available, all existing devices can handle much
higher timing precision than 10ms. A 10kHz default seems acceptable
without introducing too much range limitation (rollover for a signed
time delta will happen at 2.5 days). Leave the 100 Hz default in
place for ticked configurations, as those are going to be special
purpose usages where the user probably actually cares about interrupt
rate.
Note that the defaulting logic interacts with an obscure trick:
setting the tick rate to zero would indicate "no clock exists" to the
configuration (some platforms use this to drop code from the build).
But now that becomes a kconfig cycle, so to break it we expose
CONFIG_SYS_CLOCK_EXISTS as an app-defined tunable and not a derived
value from the tick rate. Only one test actually did this.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
We use the following commands to rename any
LED._GPIO_{CONTROLLER,PIN,FLAGS} to
DT_ALIAS_LED._GPIOS_{CONTROLLER,PIN,FLAGS}
git grep -l LED._GPIO_CONTROLLER | xargs sed -i 's/LED\(.\)_GPIO_CONTROLLER/DT_ALIAS_LED\1_GPIOS_CONTROLLER/g'
git grep -l LED._GPIO_PIN | xargs sed -i 's/LED\(.\)_GPIO_PIN/DT_ALIAS_LED\1_GPIOS_PIN/g'
git grep -l LED._GPIO_FLAGS | xargs sed -i 's/LED\(.\)_GPIO_FLAGS/DT_ALIAS_LED\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We use the following commands to rename any
SW._GPIO_{CONTROLLER,PIN,FLAGS} to
DT_ALIAS_SW._GPIOS_{CONTROLLER,PIN,FLAGS}
git grep -l SW._GPIO_CONTROLLER | xargs sed -i 's/SW\(.\)_GPIO_CONTROLLER/DT_ALIAS_SW\1_GPIOS_CONTROLLER/g'
git grep -l SW._GPIO_PIN | xargs sed -i 's/SW\(.\)_GPIO_PIN/DT_ALIAS_SW\1_GPIOS_PIN/g'
git grep -l SW._GPIO_FLAGS | xargs sed -i 's/SW\(.\)_GPIO_FLAGS/DT_ALIAS_SW\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We use the following commands to rename any _PWM_{CONTROLLER,CHANNEL}
to *_PWMS_{CONTROLLER,CHANNEL}
Used the following commands to make these changes:
git grep -l '[A-Z_0-9]*_PWM_CONTROLLER' | xargs sed -i 's/\([A-Z_0-9]*\)_PWM_CONTROLLER/DT_ALIAS_\1_PWMS_CONTROLLER/g'
git grep -l '[A-Z_0-9]*_PWM_CHANNEL' | xargs sed -i 's/\([A-Z_0-9]*\)_PWM_CHANNEL/DT_ALIAS_\1_PWMS_CHANNEL/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/printk.h to sys/printk.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pwm.h to drivers/pwm.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_.*_GPIO_{CONTROLLER,PIN,FLAGS} ->
DT_.*_GPIOS_{CONTROLLER,PIN,FLAGS)
Used the following commands to make these conversions:
git grep -l DT_.*_GPIO_CONTROLLER | xargs sed -i 's/DT_\(.*\)_GPIO_CONTROLLER/DT_\1_GPIOS_CONTROLLER/g'
git grep -l DT_.*_GPIO_PIN | xargs sed -i 's/DT_\(.*\)_GPIO_PIN/DT_\1_GPIOS_PIN/g'
git grep -l DT_.*_GPIO_FLAGS | xargs sed -i 's/DT_\(.*\)_GPIO_FLAGS/DT_\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Quark D2000 SoC files and first-order related DT bindings.
A few config options have been moved from the CONFIG_* space to
the DT_* space, as they were defined in the D2000 Kconfig files
and "leaked" into the other Quark trees.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Cleanup references to boards in some of the example and use the same
boards through the examples. Other minot cleanups and make the text more
generic and not specific to certain boards.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Hardware PWM make sense for servo control even in a sample, add HW PWM
choice for NRF52 family, which support it.
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Add a minimal sample that showcases minimal ROM sizes. It can be built
in several configurations, all very restrictive when it comes to
features enabled in order to verify the fact that we can fit in small
devices and to be able to accurately measure the sizes of the kernel's
basic features.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This sample did not enable gpio driver, so nothing happens after flash
firmware into a board.
By enabling gpio driver to fix it.
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
A new role :zephyr_file: is available that renders to a link to the file
or folder in GitHub. Find appropriate references using :file: and
convert to :zephyr_file: to take advantage of its linking capability.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Most of the basic tests trigger LEDs or expect button press and would
hang in device testing because we can't parse success or failure from
the console. Define harness for this with the intent to skip those in
sanitycheck device testing and until we have a better way to test those.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some boards' configuration does not enable GPIO by default,
like nrf52_pca10056, it causes ASSERTION FAIL when running
this application. This fix is to enable GPIO by default for
the basic threads sample, like basic blinky sample does.
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
commit ddf744deee ("drivers: pwm_nrfx: Use Device Tree label as
instance name") removed the config setting for PWM names and replaced
it with DT_NORDIC_NRF_PWM_PWM_*_LABEL.
This change is causing the blink_led and fade_led samples to break
when compiled for nRF52 boards.
Let's update the samples to use the DT setting.
Signed-off-by: Michael Scott <mike@foundries.io>
Update the filters that are extracting info from DT to use a define that
has a DT_ prefix so its clear that its coming from DT_. Also this lets
us remove any non-DT prefixed defines in the conf db.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Indicate that PWM is supported on several Nordic DK boards so that
the pwm_nrf5_sw and pwm_nrfx drivers are covered by CI builds.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable HW PWM driver instead of the SW one on nRF SoCs where the PWM
peripheral is present.
Default PWM instances are also enabled on Nordic DK boards so that it
is possible to build the basic fade_led sample for them without extra
adjustments.
After the above changes are applied, some configuration alterations
in basic samples blink_led and fade_led become no longer needed.
These are removed. And the blink_led sample is corrected so that it
works with the nRF HW PWM driver as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Supported PWM at pins A0, D3, D5 and D6 which are also Arduino
compatible. Also the onboard red LED can be used with PWM.
The basic/{fade_led, blink_led} samples to apply to this board
seemlessly and operate on the onboard red LED.
Also supported RTC.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
Move to latest cmake version with many bug fixes and enhancements.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
blinky/button and disco samples are now using definitions
generated from boards dts files.
Update samples README files accordingly.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
It is safe to assume that if X_GPIO_CONTROLLER is defined (hence
generated) X_GPIO_PIN should also be defined.
If this is not the case, this is an issue and letting the sample
build will reveal the issue.
Update the yaml filter to rely only on _GPIO_CONTROLLER #define's
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In disco basic sample, same GPIO controller was used for LED0
and LED1, which is actually a particular case.
This change implements the general case, where LED0 an LED1 might
not have the same gpio controller.
Tested on nucleo_f429zi and frdm_k64f.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since the Arduino 101 and the Quark SE C1000 are not actively developed
boards, default to other boards that are maintained and used.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Do not limit to whitelisted boards, instead make it build/run for any
board that defines required DTS macros.
Remove QMSI kconfigs and depend on DTS only.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not limit to whitelisted boards, instead make it build/run for any
board that defines required DTS macros.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not limit to whitelisted boards, instead make it build/run for any
board that defines required DTS macros.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
1. Modified fade_led PWM example to include
nRF HW PWM option.
2. Added fade_led nrf52_pca10040.overlay
in order to enable PWM node and choose
output PWM GPIO for channel 0. Channel 1
GPIO enable but not used in sample src.
Signed-off-by: Gaute Gamnes <gaute.gamnes@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Now that we set LED info in the device tree for all boards we don't need
to special case handle in the name/led pin (it comes from DT). We can
also remove include board.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The only difference between the F413xH and F413xG is flash memory size.
STMF413xH: 1536 Kbytes
STMF413xG: 1024 Kbytes
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
We update 'blink_led', 'fade_led' and 'rgb_led' to support dt generated
defines for the PWM info needed for each. Since hexiwear_k64 supports
generating the info, moved the support for hexiwear_k64 to just use the
dt generated defines.
For 'blink_led' and 'fade_led' we use an alias in dt called 'pwm-led0'.
For 'rgb_led' we use aliases 'red-pwm-led', 'green-pwm-led' and
'blue-pwm-led'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For blink_led, fade_led, and rgb_led, we only need board.h for the
hexiwear_k64 board. Remove other references to board.h and only
include it if we are building on hexiwear_k64
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When using an IDE (e.g. Eclipse, Qt Creator), the project name gets
displayed. This greatly simplifies the navigation between projects when
having many of them open at the same time. Naming every project "NONE"
defeats this functionality.
This patch tries to use sensible project names while not duplicating
too much of what is already represented in the path. This is done by
using the name of the directory the relevant CMakeLists.txt file is
stored in. To ensure unique project names in the samples (and again, in
the tests folder) folder, small manual adjustments have been done.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Remove redundant 'sample' tag and add something that matches the
functionality and features being tested, demonstrated.
Avoid short abbriviations and using full names for fs.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add support for nRF boards by using the software-based PWM driver. The
prescaler has to be configured so that the clock runs slower in order to
make the on-board LED blink in the way it is described in the Readme.
Signed-off-by: Johannes Hutter <johannes@proglove.de>
There is no reason why this sample should have a higher version required
of CMake in order to build.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit updates the button sample to use the dts-generated
define to configure the button pull-up when the custom define
is not present.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Rename GPIO_INT_CONF to GPIO_FLAGS in order to be able to use
the definition generated by the devicetree, eliminating the need
for definition in the board.h file
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Prepend the text 'cmake_minimum_required(VERSION 3.8.2)' into the
application and test build scripts.
Modern versions of CMake will spam users with a deprecation warning
when the toplevel CMakeLists.txt does not specify a CMake
version. This is documented in bug #8355.
To resolve this we include a cmake_minimum_required() line into the
toplevel build scripts. Additionally, cmake_minimum_required is
invoked from within boilerplate.cmake. The highest version will be
enforced.
This patch allows us to afterwards change CMake policy CMP000 from OLD
to NEW which in turn finally rids us of the verbose warning.
The extra boilerplate is considered more acceptable than the verbosity
of the CMP0000 policy.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Rework samples using LED and GPIO to enforce use of "CONTROLLER"
as LED and PGIO postifx.
Change impact all samples that could be run by boards yet moved to
GPIO node generations, which is only STM32 for now
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Applies to #4008 and #5159 for this board. Problem is that the
button interrupt callback was only firing once. Solution is to
set the pin pull up flag to GPIO_PUD_PULL_UP.
Signed-off-by: Anders Pitman <tapitman11@gmail.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The GPIO unit on the SAM0 is called 'PORT' which conflicts with the
name used in this sample. Rename to LED_PORT instead.
Signed-off-by: Michael Hope <mlhx@google.com>
The basic/threads sample is printing a log that looks like this:
Toggle USR0 LED: Counter = 0
Toggle USR1 LED: Counter = 0
Toggle USR0 LED: Counter = 1
Toggle USR0 LED: Counter = 2
Toggle USR0 LED: Counter = 3
Toggle USR0 LED: Counter = 4
From that log you would think that it was logging when leds were
blinking, but actually the led-threads might have crashed, and it
would just continue logging anyway. All it's doing is executing
printk's at roughly the same frequency as the LED's are blinking.
This patch rewrites the sample to use a FIFO so that the printk's only
trigger if the LEDs are actually blinking.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Remove build_only and add harness type needed for the sample/test to
allow running with sanitycheck and on devices once we have harness
support.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Still need a better way to filter and a better way to support multiple
platforms with these tests, but for now we remove the build_only tag and
make it depend on real HW.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The following files didn't have any copyright or license headers on them
when they got contributed. So add the SPDX Apache license and
appropriate copyright info:
boards/arm/stm32l476g_disco/pinmux.c
samples/basic/threads/src/main.c
tests/net/socket/tcp/src/main.c
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The hexiwear_k64 board can drive the leds with a pwm, so update the
rgb_led sample to work with this board.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hexiwear_k64 board can drive the leds with a pwm, so update the
fade_led sample to work with this board.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hexiwear_k64 board can drive the leds with a pwm, so update the
blink_led sample to work with this board. Reduces the maximum blinking
frequency from 500 Hz to 64 Hz because your eye can't distinguish these
higher frequencies (the led appears solidly on). Increases the minimum
blinking frequency from 0.5 Hz to 1 Hz because the mcux pwm driver can't
handle frequencies less than 1 Hz.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We have many testcases doing filtering both on the architecture level
and the platform level, which is redundant. Also many testcases are
running the same test twice on the same SoC for no good reason, cleanup
the tests and cleanup the filtering.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This will prepare test cases and samples with metadata and information
that will be consumed by the sanitycheck script which will be changed to
parse YAML files instead of ini.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The STM32F412 has PWM output capabilities. Add support to the blink_led
samples.
Tested using a Nucleo STM32F412ZG board (PWM output on pin 28 of the
CN11 Morpho connector and pin 29 of the CN10 Zio connector).
Change-Id: I75fb986fa97bd1c07c6375938430e7963297cd9d
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The STM32F413 has PWM output capabilities. Add support to the blink_led
samples.
Tested using a Nucleo STM32F413ZH board (PWM output on pin 28 of the
CN11 Morpho connector and pin 29 of the CN10 Zio connector).
Change-Id: I3b25b09cab54265b28088ac9681aec588d9d48b5
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Rename SOC_STM32L476XX to SOC_STM32L476XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: I834bb5b83c24c39e90c0492a2b22a7c7802de361
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08c682bfc0b80dfa88de859e90a011bcd2db2762
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
