This shield uses a non-standard UART exposed via Arduino-R3
compatible header pins.
It has configurations for FRDM_K64F and nRF52840_PCA10056.
Signed-off-by: Michael Scott <mike@foundries.io>
Be consistent in how board docs are named and move all to index.rst.
This will make the URL to the board documentation predictable and easier
to remember.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use auto-generated device tree macros in LPS25HB driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DS0 driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS3MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS2MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DSL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add LSM303AGR ecompass (accelerometer + magnetometer) sensor support.
The LSM303AGR accelerometer and LSM303AGR magnetometer are s/w
compatible with respectively LIS2DH and LIS2MDL sensors and can
share same driver with those sensors.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The frdm_kw41z can be used as a standalone board or as an arduino
shield. Zephyr already supports the standalone configuration, this
change introduces support the arduino shield configuration.
In the arduino configuration, the frdm_kw41z operates as a ble
controller over serial hci. It can be attached to another board, such as
the frdm_k64f or mimxrt1050_evk, which runs the ble host.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Cleanup unused leftover from shield development.
These flags are not actually useful, nor used as dts connectors
are sufficient to control board to shield binding is
operational and dtc provides meaningful error message
when this is not the case.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to provide a way to control boards/shields compatibility,
provide connector flags.
One should select this flag in Kconfig.board to state connector
compatibility for the board.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
