Allow to flash either Cortex M4 or M7 with OpenOCD
(depending on which Board/Core has been compiled)
Command: west flash
Warning: Dependency with recent OpenOCD patch:
Windows: https://gnutoolchains.com/arm-eabi/openocd/
version 20200408
Linux : http://openocd.zylin.com/
SHA1: 0a804222da63c5f849efa23b019a59e2dea76842
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
The Kconfig I2C_[0-9] sybmols don't have any meaning for the majority of
SoCs. The drivers doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* Define USB driver for base stm32wb device.
* Enable USB for the nucleo_wb55rg board.
* Properly initialize USB power + clock for the platform.
Signed-off-by: Pete Johanson <peter@peterjohanson.com>
Enable I2S_STM32 in the soc common part, so it will no
longer be required in board default configuration.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Rename a few cases of DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY that snuck
in after the initial global change.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the asynchronous UART API testing support on the SAM
E54 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Following other drivers, Kconfig based instances are now entirely
removed. In order to do this change, PWM nodes in board DT files have
been given a pwm{N} label so that both:
- DT API checks such as #if DT_HAS_NODE(DT_NODELABEL(pwmN)) can be
used (N being PWM instance number).
- DT references can be written as pwms = <&pwmN x y>; instead of
pwms = <&{/soc/timers@XXXXXXXX/pwm} x y>;
This approach is also used on the Linux Kernel.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
For auto doc generation purpose, get name value of boards' yaml files
in sync with name provided as board name in .rst file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The Kconfig PWM_[0-3] sybmols don't have any meaning for kinetis family
SoCs. The driver doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Kconfig PWM_[0-3] sybmols don't have any meaning for nrf family of
SoCs. The driver doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the `i2c-0` alias for the Atmel SAM R21 Xplained Pro
board, as required by the I2C test.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the `i2c-0` alias for the Atmel SAM E54 Xplained Pro
board, as required by the I2C test.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit configures the SERCOM2 peripheral to I2C mode for the Atmel
SAM D21 Xplained Pro board.
Note that the SERCOM2 on PA08/PA09 is the I2C peripheral/pin designated
by the board user guide.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit configures the SERCOM2 peripheral to I2C mode for the Atmel
SAM D20 Xplained Pro board.
Note that the SERCOM2 on PA08/PA09 is the I2C peripheral/pin designated
by the board user guide.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Remove the USART 2 definition from the nucleo_g474re board
as it could cause a pin conflict on LPUART1 TX pin (PA2).
The USART2 is not present on this nucleo hardware and then
the g474re board definition is aligned with the nucleo_g431rb.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The OpenOCD JTAG reset causes the SAM E54 SoC to prematurely start code
execution before the SoC is ready, and this causes hard faults when the
MPU is enabled -- causing OpenOCD to hang.
This commit disables the JTAG SRST reset mechanism and falls back to
using the Cortex-M SYSRESETREQ emulation reset mechanism, which does
not have experience this issue.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the ARM memory protection unit for the SAM D54
Xplained Pro board, since `CPU_HAS_ARM_MPU` is now selected by the SoC
Kconfig.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the QEMU icount mode for `mps2_an521`, in order to
decouple the host clock from the emulated guest clock.
This prevents guest timing instability from causing test failures when
the host CPU load is very high.
The icount `shift` value of 7 was empirically chosen to allow the tests
to complete in both realistic and reasonable amount of time.
The following are quick notes on the parameters used:
* -icount shift=7: Execute one instruction every 128ns of virtual time
* -icount align=off: Do not synchronise the host and guest clocks
* -icount sleep=off: Advance virtual time without sleeping/waiting
* -rtc clock=vm: Isolate the guest RTC time from the host
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
For autogeneration on board pages and indexes, consistency in naming is
required, few board names did not match the images of the boards.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Removing this flag allows to find the spi binary generation tool
in cmake's default paths. This also aligns this CMakeList with
the version currently found in the MEC EVB
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Add board definition for the NXP LPCXpresso55S16 development
board. Only non-secure (ns) access is supported for now.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Kukui has two I2C ports with various peripherals including a battery
charger and a TCPCi-compatible port controller
Enable I2C so that these can be used. No drivers are provided so far.
Also update the GPIO documentation while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove dts_fixup.h files that are not used (empty) or the defines aren't
used anymore and thus can be removed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Do not assume in the SoC level device trees that NXP Kinetis FlexTimer
nodes will always be configured as PWM. Instead, configure FlexTimer
nodes for PWM at the board level for NXP Kinetis boards.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The board efr32_radio_brd4250b replaces this removed board. This
commit removes this duplication.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
The HTML documentation generation does not work properly if
we try to put more than one board into same directory. So rename
the directory to reflect this.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit enables the QEMU icount mode for `mps2_an385`, in order to
decouple the host clock from the emulated guest clock.
This prevents guest timing instability from causing test failures when
the host CPU load is very high.
The icount `shift` value of 7 was empirically chosen to allow the tests
to complete in both realistic and reasonable amount of time.
The following are quick notes on the parameters used:
* -icount shift=7: Execute one instruction every 128ns of virtual time
* -icount align=off: Do not synchronise the host and guest clocks
* -icount sleep=off: Advance virtual time without sleeping/waiting
* -rtc clock=vm: Isolate the guest RTC time from the host
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SoC node has compatibles for the specific SoC in place, having the
same compatible at the top level is technically a conflict and the
top-level one should really just be about the board. Remove the SoC
related compatibles at the top-level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert old style ifdef(DT_NS16550_400F2400_BASE_ADDRESS) to
if DT_HAS_NODE(DT_NODELABEL(uart0)) to decide to config pins for UART0
and similarly for UART1.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of CAN_X Kconfig symbols by access to dt instances
Control of enabled instances is now done using dts nodes status
field ('okay'/'disabled'). For boards supporting only can2,
can1 instance is disabled.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update STM32WB HCI lib support to version 1.5.0.
Additionally provide a doc section to clarify compatibility
with stm32wb wireless co-processor binaries.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
The pinmux_mchp_xec is also being updated since it's using DT
from GPIO.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Pinmux needs to be set for UART_2 if it is enabled. So use
the new DT macro to refer to the DT node.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Pinmux needs to be set for UART_2 if it is enabled. So use
the new DT macro to refer to the DT node.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This commit renames the Kconfig `FLOAT` symbol to `FPU`, since this
symbol only indicates that the hardware Floating Point Unit (FPU) is
used and does not imply and/or indicate the general availability of
toolchain-level floating point support (i.e. this symbol is not
selected when building for an FPU-less platform that supports floating
point operations through the toolchain-provided software floating point
library).
Moreover, given that the symbol that indicates the availability of FPU
is named `CPU_HAS_FPU`, it only makes sense to use "FPU" in the name of
the symbol that enables the FPU.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options and dts fixups for GPIO instances.
A side-effect to using DT_INST_FOREACH is that GPIO ports A0 and A3
are now enabled, whereas they were originally disabled by default as
an optimization.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Reworked spi_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit enables the ARM memory protection unit for the SAM 4S
Xplained board, since the `CPU_HAS_ARM_MPU` is now selected by the SoC
Kconfig.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the ARM memory protection unit for the SAM 4E
Xplained Pro board, since the `CPU_HAS_ARM_MPU` is now selected by the
SoC Kconfig.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Sort the supported lists alphabetically for some boards. I'm not
trying to do this for all boards, just some DKs I'm using for testing.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Tests were failing as they were looking for an alias which didn't exist
Also, because some code in kscan_handlers.c wasn't compilable
Signed-off-by: Mark Olsson <mark@markolsson.se>
Changes dependency for I2C so that it's enabled if kscan is enabled.
This is to allow the kscan_ft5336 sample to run.
Note: LVGL has KSCAN as a dependency.
Applies to the mimxrt10{50,60,64}_evk boards.
Signed-off-by: Mark Olsson <mark@markolsson.se>
Adds device tree nodes, pinmux definitions and configures Kconfig
defaults for the ft5336 touch panel driver on the
stm32f746g_disco board.
Signed-off-by: Mark Olsson <mark@markolsson.se>
Adding port information for uart tx and rx pins in dts, so that it can
be more systematically retrieved in the uart driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Convert driver to use DT_INST_ defines. As part of this conversion we
remove the Kconfig options for per GPIO controller enables and instead
get that information from device tree. This means we now disable each
GPIO controller by default in the DTS and have each board dts enable the
GPIO controller ports it needs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the asynchronous UART API testing support on the SAM
R21 Xplained Pro board.
The SERCOM3 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM3 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Adding support for nRF9160 based InnBlue board V2.1. Supports both
Secure and Non-Secure configurations along with various sensors
(lis2dh12 / hts221) and devices(i2c / pwm).
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Move the FPGA GPIO init to use the devicetree.h macros instead of
dts_fixup.h. This allows us to remove dts_fixup.h on mps2 based
platforms.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
SPI1, which is used by the LoRa radio, has the following
configuration:
SCK: PB_3
MISO: PA_6
MOSI: PA_7
NSS: PA_15
Update the pinmux configuration and documentation to reflect this.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Convert old DT defines of the form DT_ARM_SCC_BASE_ADDRESS to
DT_REG_ADDR(DT_INST(0, arm_scc)). This allows us to remove dts_fixup.h
on musca boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In conversion of nodelabels to match SoC docs, we missed a case in the
board dts files. However these delete-node commands are not needed as
we normally handle this via the 'status' property being disabled which
enet2 is by default in the SoC dtsi files. So we can safely just remove
the stale /delete-node/ eth1 lines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adding support for nRF9160 based InnBlue board V2.2. Supports both
Secure and Non-Secure configurations along with various sensors
(lis2dh12 / hts221) and devices(i2c / pwm).
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Set the default value of SYS_PM_MIN_RESIDENCY_SLEEP_1 and
SYS_PM_MIN_RESIDENCY_SLEEP_2 to something more reasonable for these
platforms, as the latency of entering/exiting these sleep modes
is low.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The nvs sample requires a storage_partition of 3 flash pages, but these
boards only provided 2 flash pages. Because of this the nvs sample
failed.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Reworked i2c_sam_twi driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked i2c_sam_twi driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update documentation about IC variations. Now SoC supports both
variations A and B and this board is compatible with both.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Update documentation about IC variations. Now SoC supports both
variations A and B and this board is compatible with both.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage. We also remove dts_fixup.h defines that
are no longer needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Mark all the individual PWMs as disabled in dts and enable the one
explicitly used on the mimxrt1064_evk.dts in the board dts file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change the board defconfig to use the provided 24MHz Crystal instead
of the internal resonator.
This improves the clock precision and stability.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Change the board defconfig to use the provided 24MHz Crystal instead
of the internal resonator.
This improves the clock precision and stability.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Reworked usart_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked uart_sam driver to utilize new DT_INST macros as part of this
rework we also now get pin ctrl/mux configuration information from the
device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We don't need to define DT_NUM_IRQ_PRIO_BITS or DT_NUM_MPU_REGIONS in
dts_fixup.h files anymore, so we can remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit enables the GMAC Ethernet support for the `atsame54_xpro`
board which includes an on-board RMII PHY.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
In order to use its serial peripheral SERCOMs SAMD socs require their
pins to be configured with pinmux. Currently pins are muxed only for the
boards' default serial interfaces. The pinmux code is written to throw
a compiler error if a user tries to use any sercom in a way it wasn't
pre-defined to be used.
This commit changes compiler errors to warnings so that user can provide
custom pinmuxing code in their app.
Fixes#23133
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
This commit enables the newly added GMAC instance in the `sam4e_xpro`
device tree.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This enable GMAC driver by default if the end application selects
NETWORKING. The driver will set MII interface since is the only one
available for SAM4E and will select a random MAC value.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This board contains an on-board Winbond W25Q16.
The chip is connected to spi1 using PB3-PB5 and PB0 as CS.
Signed-off-by: Bjarne Steinsbo <bjarne@gmail.com>
While the Cortex-R arch port does not currently support memory
protection and userspace, the `memory_protection` and `userspace` test
tags should not be ignored because doing so can unintentionally disable
other relevant tests.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Following conversion of stm32 i2c driver to use of DT_NODELABEL
macros, configuration of i2c instance in stm32 boards should
no more be done thanks to Kconfig symbols, but is done thanks
to device tree file.
Clean boards files from these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This adds the support of openocd for nucleo board stm32g474re
It requires the openocd that supports stm32G4xx
(zephyrproject-rtos/openocd#24)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds the support of openocd for nucleo board stm32g431rb
It Requires the openocd that supports stm32G4xx
(zephyrproject-rtos/openocd#24)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds the support of openocd for nucleo board stm32g071rb
It requires the openocd that supports stm32G0xx
(zephyrproject-rtos/openocd#24)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Towards moving uart mcux driver to DT_INST based, we need to convert
uses of CONFIG_UART_MCUX_[0-9] to use DT_NODELABEL instead. This way
the pinmux settings are still based on specific instances of the uart.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit fixes the incorrect memory (FLASH and SRAM) size
specification in the device tree and the board test yaml files.
The `qemu_cortex_r5` board (using `fdt-single_arch-zcu102-arm.dtb` FDT)
has 64MiB RAM at the address 0 and 32MiB QSPI flash at 0xc0000000.
QEMU `info mtree`:
0000000000000000-ffffffffffffffff (prio 0, i/o): memory@00000000
0000000000000000-000000000002ffff (prio 0, ram): ddr_bank1_1@0x0
0000000000030000-000000000003ffff (prio 0, ram): ddr_bank1_2@0x30000
0000000000040000-0000000003ffffff (prio 0, ram): ddr_bank1_3@0x40000
00000000c0000000-00000000c1ffffff (prio 0, i/o): lqspi
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Use the new devicetree API. Remove per-board enabling of ADC_0 by
setting ADC_0 to default y when the 'adc' node label points at an
enabled node of the expected compatible (depending on SoC).
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Those are used only in tests, so remove them from kernel Kconfig and set
them in the tests that use them directly.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as spi. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as usart. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as i2c. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
