Add SPI support to the NXP TWR-KE18F development board. There are no
onboard SPI devices, but both SPI busses are available on the primary
Tower System elevator connector.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This enables the ROM bootloader on the CC13x2 / CC26x2 LaunchPad
development boards. The bootloader can be started by holding BTN-1
during reset. This can be useful during development to recover a board
if DAPs get disabled.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
All three boards use a Skyworks SPDT switch to control whether the
antenna is connected to a PCB antenna or an external u.FL connector.
None of them power up in a state that properly enables an antenna.
Add startup code to configure for the PCB antenna.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/14123
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
[mike@foundries.io: adjusted code to use Zephyr GPIO APIs. boron is
now also based on DTS.]
Signed-off-by: Michael Scott <mike@foundries.io>
MCUboot needs nearly all 8 pages, on some commits even more. This leads
to a overwrite of parts of mcuboot code when an application is flashed.
By improving the size of the boot partition to 10 pages (from 8) and
decrease both application slots by 1 page, MCUboot fits in the boot
loader partition. This is also fixable by an extra .dts, but having an
out of the box working configuration is preferable.
Signed-off-by: Stefan Kraus <stefan.kraus@fau.de>
Add partition table to support MCUBoot. A paragraph of
usage comments was also added in the board documentation.
Signed-off-by: Jun Li <jun.r.li@intel.com>
Use the generic pinmux APIs provided by zephyr to select
alternate functions.
This also contains a fix for a formatting issue in the
documentation for this board. Additionally, the serial
console is now on UART2.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
USB_DC_STM32 comes from Kconfig. We have to add the CONFIG_ prefix
to use USB_DC_STM32 in C code.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Create a dedicated connector file to hold arduino connector
information for disco_l475_iot board.
This should enhance board dts file readability.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adds a new argument to the jlink runner to reset the device after
loading code to flash. This fixes a problem with the lpcxpresso54114
board where it was necessary to manually reset the board to get new code
to start running after the 'ninja flash' command. This new argument is
optional and false by default because there are some cases were we must
not reset after load, such as when we load the application into ITCM on
imx rt devices.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1060_evk
board. Updates the board documentation and yaml supported list
accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Since there is no NFC antenna connector on the dongle and the pins
P0.09 and P0.10 that are dedicated to NFC functionality are in the
group of just a few ones available for external connections, it seems
more reasonable to configure these pins by default as regular GPIOs,
as users will most likely want to use them in this way.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
These definitions were left incorrect after a gpio-map change was
added to the PR introducing the boron support for the SARA-R4 modem.
Correct the gpio defintions here so that the boron build doesn't
break.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/16289
Signed-off-by: Michael Scott <mike@foundries.io>
Enable pull-up on UART TX pin to reduce power consumption.
If the board is powered by battery the SoC consumes more
power than expected.
The consumption increases because TX pin is floating
(High-Impedance state of pin B from Dual-Supply Bus Transceiver).
Similar to commit b5b728495b
("boards: reel_board: enable pull-up on UART RX pin")
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The Particle.io Boron is an nRF52840-based board with a connected
u-blox SARA-R4 modem. The main board was previously upstreamed
without modem support.
Now that we have a driver to support the SARA-R4 modem, let's enable
it for the Boron board.
Signed-off-by: Michael Scott <mike@foundries.io>
Let's change the specific WNC-M14A2A check into a more generic
MODEM check for enabling ethernet. Many of these pins are used
on the Arduino headers.
Signed-off-by: Michael Scott <mike@foundries.io>
This commit adds a DTS node for the ARM MPU peripheral in the
device tree of ARMv8-M SoCs (for the secure and the non-secure
DTS descriptions) and updates the fixup files. SoCs:
- nrf9160
- musca_a
- musca_b1
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
MHU (Message Handling Unit) enables software to raise interrupts to
the processor cores. It is enabled in SSE 200 subsystems.
This patch aims to implement inter processor communication.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Add support for the NXP TWR-KE18F development board. This board
feautures an NXP MKE18F16 MCU, a selection of user LEDs and
push-buttons, potentiometer, thermistor, CAN interface, and FlexIO
header.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The mikroe_mini_m4_for_stm32 board is developed by Mikroelektronika
not by STMicroelectronics.
Also use more appropriate "mini-m4-for-stm32" board name for
compatible dt property.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Enable the counter capability in the board and add a .conf file for the
nRF52810 running on the PCA10040 board.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The supported field is used by sanitycheck to select which tests will be
run on a particular board. The issue with the counter drivers, and in
particular on nRF ICs, is that the timer peripherals are disabled by
default and need to be enabled on a per-board basis inside a .conf file.
Since this board doesn't have a .conf file in
tests/drivers/counter/counter_basic_api/boards/ the test cannot be run
on this board.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit adds support for board: nrf52811_PCA10056.
The nRF52840 DK: PCA10056 is the recommend development kit, it emulates
the nRF52811, and can be used as a starting point for development
before moving over to a custom board.
Please note that this development kit does not support Bluetooth
Direction Finding. What is more it cannot be used with most of Arduino
shields because of PCA10056 PIN layout.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit adds J-Link runner for efr32_slwstk6061a board. To use it
it is necessary to install J-Link Software and Documentation Pack.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit enables internal SoC DC-DC converter on efr32_slwstk6061a
board.
RF components on efr32_slwstk6061a board are connected to the internal
SoC DC-DC converter. Upon startup the DC-DC converter is configured in
the bypass mode. Such configuration provides enough power for the SoC to
boot and perform basic operation. It is not enough however to operate
the radio subsystem. Without this patch enabling radio in Rx or Tx mode
causes voltage drop and triggers brown out detector reset.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Hook up SERCOM1 to I2C, it is connected to the EXT3 header and
the EDBG embedded debugging interface.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
The ADC driver in this PR has been tested working on these nucleo
boards, so ADC support is added to the boards doc.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Some configuration for the boards have to be added into test_adc.c file
so user can test driver with the test cases. Several nucleo boards are
added including F091RC/F103RB/F207ZG/F302R8/F401RE/F746ZG/L073RZ/L476RG.
And also ADC dts and pinmux configuration are added into boards own
pinmux.c and dts file.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Let allow users to select the revision B of the chip on the SAM E70
Xplained Board. The same board exists with SoC revision A or B.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
At the moment there are two images for Nucleo-64 STM32 family board
connectors (img/nucleo_xxxxxx_connectors.png).
The images have the same canvas size (800x619) but different file
size in bytes and different color coding.
The first one (192K, 8-bit colormap) is used for
* nucleo_f070rb
* nucleo_f091rc
* nucleo_f103rb
* nucleo_l053r8
* nucleo_l073rz
The second one (464K, 8-bit/color RGBA) is used for
* nucleo_f030r8
* nucleo_f302r8
* nucleo_f334r8
Applying simultaneous black/white threshold to the images and
comparing them with imagemagick tools shows that the images
have no significant difference. Therefore we can use
nucleo_l073rz_connectors.png for nucleo_f030r8, nucleo_f302r8
and nucleo_f334r8.
Please see https://github.com/zephyrproject-rtos/zephyr/pull/15926
for details.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
The Holyiot YJ-16019 board is a small, coin cell driven board based on
the Nordic Semiconductors nRF52832. It provides one LED and one push
button.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The approved trademark name is Wi-Fi so update references to WiFi and
other spellings to Wi-Fi in documentation and Kconfig help strings.
(Note that use of spelling variatios of "wifi" in module names, CONFIG
names, link names and such are untouched.)
https://www.wi-fi.org/
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The stm32_min_dev board blue/black variant support USB device,
but the usb node removed by merge PR #15245, so add it back.
Signed-off-by: Harry Jiang <explora26@gmail.com>
The TI CC1352R LaunchPad (LAUNCHXL-CC1352R1) is a development kit that
features the CC1352R SoC.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
The TI CC26x2R LaunchPad (LAUNCHXL-CC26X2R1) is a development kit that
features the CC2652R SoC.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Fix "arduino_i2c not found" issue, similar to #13708
Add arduino interfaces in dts to board nrf52_10040
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Enables BT_CTLR if BT is enabled, connects shell-uart to uart0,
and enabled NRFX uart driver by default.
Signed-off-by: Tavish Naruka <tavishnaruka@gmail.com>
Implementation of pinmux for the stm32mp157c_dk2 board.
Some UART pin mux definition has been added (mainly for
UART console and UART/SPI Arduino shield support).
This can be completed with pin mux for other stm32mp157c
UART.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for stm32mp1 basic UART API with Zephyr.
UART Console and UART shell are also supported.
Async UART API and USART support is to be done.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Move SERCOM peripherals to use the raw defines generated from DTS
parsing. This adds aliases to the DTS so that the SERCOM number
can still be used for clocking and pinmux.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
The 96Boards Argonkey mezzanine board has been officially
published on ST website:
https://www.st.com/en/evaluation-tools/steval-mki187v1.html
Update documentation with official picture and website info.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The mimxrt1015_evk board image was corrupted and did not display
properly in the board documentation. Fix it.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This was tested with the hello world application. UART 0 was used
as console for displaying "Hello World! mec15xxevb_assy6853" to
the serial terminal.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
soc : arm : microchip_mec Use rename fault clear function
The Cortex-M core function to clear faults was rename by
upstream. Update to use new name.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
The Atmel SAMD21 (and therefore also the SAMR21) comes with the same
RTC peripheral as the Atmel SAMD20.
Enable it in dts_fixup.h and enable it in the dts for samr21_xpro.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Add the Atmel SAM R21 Xplained Pro Evaluation Kit to zephyr.
So far, UART, SPI, I2C (depends on #14128), debug LED and user button
have been tested.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Since STM32_OSPEEDR_VERY_HIGH_SPEED flag is required for all I2S_CK
pins, lets add this to the STM32F4 pinmux header and remove the
duplicates in board files. While we are at it, let's add the missing
pinmux definitions for I2S_2 also.
Fixes: #9028
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Replace image and reword some sections to indicate the presence of two
board variants: stm32_min_dev_(blue|black)
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Add support for blue pill and black pill variants of the STM32
minimum development board by splitting board configuration into
stm32_min_dev_blue and stm32_min_dev_black.
CODEOWNERS: Add myself (@cbsiddharth) as codeowner for stm32_min_dev
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
We shall not enable by default a system timer in ARM
platforms, namely the SysTick, the Nordic, or the SAM0
RTC timer, simply by assessing the hardware capabilities
(e.g. by conditioning on CPU_CORTEX_M_HAS_SYSTICK).
Instead, now, all ARM platforms needs to explicitly set
their system timer module. Note that this has already
been the case for ca 80% of the ARM platforms.
This clean-up allows us to decouple HW capabilities from
system configuration (for example, Nordic platforms may
enable option CPU_CORTEX_M_HAS_SYSTICK, and still use
the platform-specific RTC timer for system timing).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add board support for 96Boards WisTrio LoRa Tracker board from
RAK Wireless. This board is one of the 96Boards IoT Edition platform.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add configuration, pinmux, dts and documentation for the STM32MP157
Discovery board based on the STM32MP157 SoC.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Mark the three distinct choices for how to program the board as
separate options, and add some clarifications on each. For the MCUboot
route, use smp_svr instead of blinky, to give the user a hint about
how to keep their devices up to date from application land.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
This patch adds support to the nRF9160 for using a dedicated
GPIO pin to reset controllers running on nrf52840_pca10090.
It resets the controller before opening the H4 device, and it
delays the controller from booting until all bytes traveling
to the host have been received and drained from the UART,
thus ensuring that communication can begin from a clean state.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Let one of the MCU interface pins be configured to act
as a reset line. This mitigates the lack of a connection
between the nRF9160 and nRF52840 PINRESET.
Minor refactoring and updated comments.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Add board support files for mimxrt1015_evk, the development board for
i.mxrt1015 (CM7) SoC.
- Add pinmux, dts, and doc.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
added three missing LEDS for stm32f4_disco, in order to run the
samples/basic/disco application on the stm32f4_disco
Signed-off-by: Jan Sturm <jansturm92@googlemail.com>
Enables the pyocd runner on mimxrt1060_evk and mimxrt1064_evk boards
using the generic cortex_m target. Note that this target is not capable
of programming flash, therefore can only load an application to internal
SRAM (set CONFIG_CODE_ITCM=y and CONFIG_DATA_DTCM=y) or attach to an
application already programmed to flash by other means (e.g., DAPLink
drag-and-drop).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Same deal as in commit 4638652214 ("Kconfig: Use 'default' instead of
'def_bool' in Kconfig.defconfig files"), fixing new stuff that got
introduced since then.
Some symbols, like ALTERA_AVALON_PIO, are only defined in
Kconfig.defconfig files, and so need the def_bool.
Motivation (from the note at the end of
guides/kconfig/index.html#common-shorthands):
For a symbol defined in multiple locations (e.g., in a Kconfig.defconfig
file in Zephyr), it is best to only give the symbol type for the "base"
definition of the symbol, and to use 'default' (instead of 'def_<type>'
value) for the remaining definitions. That way, if the base definition
of the symbol is removed, the symbol ends up without a type, which
generates a warning that points to the other definitions. That makes the
extra definitions easier to discover and remove.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add configuration, dts and documentation for the MINI-M4 for
STM32 board based on the STM32F415RG SoC.
See https://www.mikroe.com/mini-stm32f4 for more details.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
This commit adds CAN support for nucleo F746zg.
Furtermore CAN was added in stm32f7.dtsi and pinmuc_stm32f7.h
CAN_RX: PD0, CAN_TX: PD1
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
2 identical packages were defined for stm32f412 SoC, invariant "g".
Merge them in new sinclge stm32f412Xg.dtsi.
Update matching boards accordinlgy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
SPI is not normally enabled, but some tests assume that there's a device
available. Conditionally enable SPI_2 which is associated with the
on-board flash.
Closes#15374
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Remove 'counter' as a supported feature on several NRF boards as these
boards fail to build tests/drivers/counter/counter_basic_api. This is
due to the fact that we either need explicit board conf files for the
test or have the counter driver enabled via Kconfig.
Fixes#15460
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
for SDK 0.10.0, it consumes more stack size when coverage
enabled, so adjust stack size to fix stack overflow issue.
Fixes: #15206.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
This is a follow up to commit 436c4262da.
By default the channel 0 of pwm0 is set to the pin that drives led0.
Since the LED is active high, the inversion of polarity is incorrect.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
for SDK 0.10.0, it consumes more stack size when coverage enabled
on qemu_x86 and mps2_an385 platform, adjust stack size for most of
the test cases, otherwise there will be stack overflow.
Fixes: #14500.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Updates the 96b_nitrogen board document to link to the new debugging
guide instead of the opensda page.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the usb_kw24d512 board
document to leverage the new debugging guide covering debug probes and
host tools.
This board does not have an OpenSDA microcontroller, therefore the only
debug probe currently supported is the external J-Link.
Updates the flashing section to reflect that the ``flash`` build system
target is now supported.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the lpcxpresso54114
board document to leverage the new debugging guide covering debug probes
and host tools.
This board supports the LPC-Link2 J-Link onboard debug probe.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the hexiwear board
documents to leverage the new debugging guide covering debug probes and
host tools.
Recommends the OpenSDA J-Link debug probe because the k64 and kw40z
share the same OpenSDA microcontroller, and the kw40z requires Segger
RTT for a console. It is possible to use daplink firmware for the k64,
however it is not recommended because it requires switching the firmware
back to jlink to access the kw40z.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hexiwear_k64f and hexiwear_kw40z share the same OpenSDA
microcontroller on the hexiwear docking station, so make the jlink the
default firmware on both for consistency. We use jlink instead of
daplink by default because hexiwear_kw40z can only use Segger RTT for
the console (there is no UART available).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The frdm_kw41z board was originally configured in zephyr to use the
jlink runner by default because pyocd didn't yet support the kw41z soc.
Support for kw41z was added in pyocd v0.9.0, so we can now default to
daplink firmware and pyocd.
Now all freedom boards in zephyr consistently use daplink and pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the freedom board
documents to leverage the new debugging guide covering debug probes and
host tools.
These boards support OpenSDA DAPLink and OpenSDA J-Link onboard debug
probes. They can also support an external J-Link probe, but this
requires board modifications (cutting traces) and is therefore not
documented.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the mimxrt1060_evk and
mimxrt1064_evk board documents to leverage the new debugging guide
covering debug probes and host tools.
Neither of these boards have OpenSDA J-Link board-specific firmware,
therefore the only debug probe currently supported is the external
J-Link.
Updates the flashing section to reflect that the ``flash`` build system
target is now supported.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the mimxrt1020_evk and
mimxrt1050_evk board documents to leverage the new debugging guide
covering debug probes and host tools.
These boards support both the OpenSDA J-Link onboard debug probe and the
J-Link external debug probe.
Corrects an error linking to the wrong OpenSDA J-Link firmware.
Updates the flashing section to reflect that the ``flash`` build system
target is now supported.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The GPIO driver is required by this board's initialization code, hence
it is forced to be enabled always, not only enabled by default like on
other boards equipped with an nRF SoC.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This patch enables the GPIO driver by default on all boards equipped
with an nRF SoC (all boards having `CONFIG_SOC_FAMILY_NRF=y` in their
`_defconfig` file).
In vast majority of cases the driver is needed, so it is more
convenient to enable it at board level than in particular
applications.
And if the driver is undesired for some reason, it can be still
disabled in the application config.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Set FLASH_LOAD_OFFSET correctly (accounting for Nordic MBR) when
BOARD_HAS_NRF5_BOOTLOADER is defined and we're not compiling MCUboot.
MCUboot will select USE_CODE_PARTITION, which will make it link
correctly regardless of which board DTS is used (stock/debugger).
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
nrf52840_pca10056 and nrf52_pca10040 was enabling RTT by default
for all samples. It has some implications like forwarding printk
to logger and that, as a default behavior, may not be welcomed.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The nRF91 DK User Guide clearly says "the LEDs are active high,
meaning that writing a logical one ('1') to the output pin will
illuminate the LED".
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable TIMER1 by default in nrf9160_pca10090 so it can be selected
by user for hardware byte counting in UARTE or other purpose.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Following fix SRAM size to take into account CCM,
enable CCM and update yaml files in boards including fixed soc
dtsi definitions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When using V0.10.0 SDK, flashing is not working anymore on
stm32f4_disco.
Using st_nucleo_f4.cfg instead of stm32f4discovery.cfg solves
the issue.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the bt-mon-uart chosen node to all the nRF-based boards so that they
can all use CONFIG_BT_DEBUG_MONITOR without additional changes.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fixes the apds9960 i2c address on the reel_board. Found while converting
the apds9960 driver to use the i2c address from device tree rather than
a hardcoded value in apds9960.h.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The current flash configurations for all nRF52840's in Zephyr is
VERY constrained when it comes to allowing samples any space for
storage or custom areas. It only leaves the last 4 pages of flash
for "storage".
The nRF52840 is also capable of using OpenThread which defaults
to using the last 4 pages of flash for storing OpenThread-related
network data.
This means that while using OpenThread under any configuration
designed to use mcuboot partition slots, there is no space left
over for storage of any kind.
Let's adjust the partition table to set storage at 8 pages of
flash (32k). This fixes the conflict with OpenThread and leaves
room for future use cases that may arise.
Signed-off-by: Michael Scott <mike@foundries.io>
USB is already being configured in pinmux.c, but for it to be
availiable it also needs to be enabled in the device tree.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This is a vestiage of how board ports use to work, we have since removed
the need for board.h to exist on all board ports. Remove the file since
its not needed and doesn't do anything useful.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Linking to API material requires knowing the pecularities of how
doxygen, sphinx, and breathe work. In an attempt to hide some of this
we're preparing the current docs to allow use of configuration defaults
that will let us more simply use a default role that will hunt for a
reference target in the various domains that are available by using a
default "role" of "all". This will let us use the simple notation
`functionname` or `typename` without fully specifying the reference as
:c:func:`functionname`.
This patch cleans up exising docs that were (incorrectly) using single
backtics where double backtics should have been used, and also found
some typos (such as a space between the role name and the reference,
such as :file: `filename`, and a missing colon such as
c:func:`functionname`)
This is a start to address issue #14313
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Updates the documentation to show PC13 instead
of PB12 as deafult LED Pin. Also adds note
about the default LED based on version of board.
Includes the change that needs to be made to
the dts file for changing default LED pin
Signed-off-by: Suryansh Sharma <suryansh@evilscientist.cc>
efm32pg_stk3402a and lpcxpresso54114_m0 board yaml files didn't set
xtools under the toolchain category, fix that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add CONFIG_SYS_CLOCK_TICKS_PER_SEC=1000 to nucleo_l053r8_defconfig.
All STM32 boards seem to have this defined.
Makes samples with ksleep work properly.
Signed-off-by: Anthony Kreft <anthony.kreft@gmail.com>
Since NET_L2_BT no longer "select"s BT and the rest of required BT
features, enable them within the defconfig file.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Maybe this is some "just in case" thing that got copied around. There's
no need to have a blank line at the beginning or end of Kconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Configure lvgl defaults for imx rt boards in their respective board
defconfigs rather than the lvgl sample application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that we have SDK 0.10.0 we can enable building this board with the
Zephyr toolchain. SDK 0.10.0 introduced support for the ARM v8m based
cores which these boards utilize.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A new role :zephyr_file: is available that renders to a link to the file
or folder in GitHub. Find appropriate references using :file: and
convert to :zephyr_file: to take advantage of its linking capability.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The nRF52840-based Particle.io boards have an external flash
module that is connected via SPI interface. Originally,
the goal was to place the flash part into deep power down
mode and save 9 uA in sleep mode, but this was never
implemented in a board initialization file.
Let's remove the default y behavior for SPI as each sample
will turn it on if needed, and it can cause certain out of
tree samples to behave badly (where CONFIG_MULTITHREADING=n).
Long term: we need a better solution for handling samples
that don't fit the requirements for certain drivers, but
for now this will clean up some board usability issues.
Signed-off-by: Michael Scott <mike@foundries.io>
JLink V6.44 (2019-03-01) added support for the imx rt1064 soc, including
programming the internal flash on flexspi2. Updates the mimxrt1064_evk
board to use the internal flash and external sdram memories by default,
now that the debug tools support them.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Do not enable by default both I2C and SPI nodes for the peripherals
with the same instance number, since they use the same MMIO base
address and DTC will issue a warning in such situation.
This patch corrects dts files for the following boards:
- nrf51_pca10028
- nrf52_pca10040
- nrf52840_blip
- nrf52840_pca10056
- nrf52840_pca10059
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
SPI_0 cannot be used simultaneously with I2C_0, since in nRF52832 SoC
these instances share certain hardware resources.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
To build apps for mcuboot, a zephyr,code-partition needs to be
identified in the DTS chosen block. Without this entry, the
following configs will always be 0:
CONFIG_FLASH_LOAD_OFFSET
CONFIG_FLASH_LOAD_SIZE
Signed-off-by: Michael Scott <mike@foundries.io>
Reduce unnecessarily large images of boards (> 1MB)
Also fixed typo in doc title for mec2016evb_assy6797
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The creation of the udev rule requires the user to be root else
it will fail. Update the text of the documentation to make it clearer
and change the shell prompt of the command to '#'
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
On nrf52810_pca10040 board, the nRF52810 SoC is emulated on nRF52832.
This patch overrides for this board the number of cycles consumed by
one iteration of the internal loop in `nrfx_coredep_delay_us()` (used
by `k_busy_wait()`), so that the value adequate for nRF52832 is used.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In the recent MDK brought by nrfx 1.6.2, these legacy peripherals have
been revealed as available also in nRF52810. This patch allows their
use in Zephyr drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The i.MX RT1064 evk has one ethernet (10/100M) connector via KSZ8081RNB
phy. Enable related dts nodes and config flags
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
This commit adds a patch in the Kconfig.defconfig file of
nRF9160_pca10090 board, that instructs the linker to restrict
the Secure image to the size of its code partition, if the
image is to be combined with a Non-Secure image. Secure images
without accompanying Non-Secure firmware (i.e. with symbol
TRUSTED_EXECUTION_SECURE not set) can use the entire flash.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We do not need to overwrite the reg property of flash0
in nrf9160_pca10090 default partitioning. The property
reflects the flash resources of the SOC, and is passed
in the .dtsi file of nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Most of the other nRF52832 boards have the following settings for
scratch and storage partitions:
scratch_partition: partition@70000 {
label = "image-scratch";
reg = <0x00070000 0xa000>;
};
storage_partition: partition@7a000 {
label = "storage";
reg = <0x0007a000 0x00006000>;
};
Let's adjust the scratch size to align with the others and add the
storage partition so that settings and FS samples will work.
Signed-off-by: Michael Scott <mike@foundries.io>
The MPU should have been enabled on all these boards since they have
Cortex-M7 and need mpu for caching support.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Most of the other nRF52832 boards have the following settings for
scratch and storage partitions:
scratch_partition: partition@70000 {
label = "image-scratch";
reg = <0x00070000 0xa000>;
};
storage_partition: partition@7a000 {
label = "storage";
reg = <0x0007a000 0x00006000>;
};
Let's remove the snowflake settings in BLENano2 which coincidentally
are incorrect: storage overruns the flash area by 0x1000 and causes
a crash when enabling FCB storage.
Signed-off-by: Michael Scott <mike@foundries.io>
Remove most unnecessary instances of `export` and `cmake` use that can
instead be replaced with `zephyr-app-commands` or similar. This is to
avoid documentation using different mechanisms to describe the same
actions and in preparation for documenting `west build` everywhere.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added more detailed information how to connect Zephyr instance
to host system like Linux desktop.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The mimxrt1060_evk was missing hwinfo in the supported list. All other
imx rt boards already have it.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes Segger RTT on the hexiwear_kw40z and usb_kw24d512 boards by
setting CONFIG_RTT_CONSOLE=y and CONFIG_USE_SEGGER_RTT=y.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Comment for storage partition could be misleading.
Clarify this is a partition used for file system.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Refactor the imx rt code/data location config defaults such that we
default to on-chip memories at the soc level and override to external
memories at the board level. This means that we frequently override soc
defaults for evk boards, but it removes the assumption that all imx rt
boards (particularly non-evk boards) will have the same external
memories as evk boards.
The end result is that imx rt evk boards still have the same defaults as
before, but the way we get there is different.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enable pull-up on UART RX pin to reduce power consumption.
If the board is powered by battery and the debugger is
not connected via USB to the host, the SoC consumes up
to 2mA more than expected.
The consumption increases because RX pin is floating
(High-Impedance state of pin B from Dual-Supply Bus Transceiver).
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This is a follow-up to commit e2b38e02bf.
Default PWM instances are enabled in Kconfig and DTS (with channel 0
set to LED0 pin) for these boards so that it is possible to build basic
samples blink_led and fade_led for them without extra modifications.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Following introduction of zephyr sdk0.10 and openocd branch
from from 20190130, stm32l4+ SoC support is now available and
flash and debug operations are available on nucleo_l4r5zi board.
Fixes 12094
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The imx rt family of socs has several options for linking code and data
into internal or external memories, and up until now we have handled
these options at the board level. This has resulted in several Kconfig
symbols being defined in multiple places and triggering warnings in
documentation builds:
warning: the default selection CODE_ITCM (defined at boards/arm/mimxrt1050_evk/Kconfig:13, boards/arm/mimxrt1060_evk/Kconfig:13) of <choice> (defined at boards/arm/mimxrt1050_evk/Kconfig:9) is not contained in the choice
warning: the choice symbol CODE_ITCM (defined at boards/arm/mimxrt1050_evk/Kconfig:13, boards/arm/mimxrt1060_evk/Kconfig:13) is defined with a prompt outside the choice
warning: the choice symbol CODE_HYPERFLASH (defined at boards/arm/mimxrt1050_evk/Kconfig:16, boards/arm/mimxrt1060_evk/Kconfig:16) is defined with a prompt outside the choice
warning: the choice symbol CODE_QSPI (defined at boards/arm/mimxrt1050_evk/Kconfig:19, boards/arm/mimxrt1060_evk/Kconfig:19) is defined with a prompt outside the choice
warning: the choice symbol CODE_ITCM (defined at boards/arm/mimxrt1050_evk/Kconfig:13, boards/arm/mimxrt1060_evk/Kconfig:13) is defined with a prompt outside the choice
warning: the choice symbol CODE_HYPERFLASH (defined at boards/arm/mimxrt1050_evk/Kconfig:16, boards/arm/mimxrt1060_evk/Kconfig:16) is defined with a prompt outside the choice
warning: the choice symbol CODE_QSPI (defined at boards/arm/mimxrt1050_evk/Kconfig:19, boards/arm/mimxrt1060_evk/Kconfig:19) is defined with a prompt outside the choice
The number of warnings increased as we added more imx rt boards. Fix the
warnings by moving code and data location configs from the board level
to the soc level.
The default memories for all imx rt boards are unchanged. The
mimxrt10{20,50,60}_evk boards still default to hyperflash/qspi for code
and sdram for data. The mimxrt1064_evk board still defaults to ITCM for
code and DTCM for data because jlink does not yet support programming
internal flash.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add nvs support to nucleo_f091rc board. This requires to
add erase-block-size property to stm32f0.dtsi.
Storage partition is set to 4kb at the end of the flash.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a space in some long doc titles to allow for wrapping in the title
display. Also fixed a table in the mec2016evb board doc.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Be consistent in how board docs are named and move all to index.rst.
This will make the URL to the board documentation predictable and easier
to remember.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The phrase "Zephyr applications use the ..." in many boards and
inconsistently. This is just to say what is the board identify is.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This was tested with a the hello world application. UART 0 was used
as console for displaying "Hello World! mec2016evb_assy6797" to the
a serial terminal.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
The board pinmux code has been using non DT_ prefixed defines for DT
generated defines. Switch to use DT_ prefixed ones as we want to
deprecated the non DT_ prefixed defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The values for the registers like GDV, SDV and Boarder Waveform
depend on the panel and display controller. Add DT properties
and obtain such values from DT.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Adding a set of BKMs on how to enable and configure UART1
for the nrf52840_pca10056 board. This instructions are likely valid
to most other nrf52840- family of boards.
Signed-off-by: Andrei Laperie <andrei.laperie@intel.com>
This commit enables the PWM0 device on the Atmel SMART SAM E70 Xplained
Board, by adding the entries to the DTS and configuring the PWM pins
from the EXT1 connector (channel 0, inverted) and EXT2 connector
(channel 2, inverted and non-inverted) with the corresponding peripheral
functions. It also updates the documentation and mark pwm as supported
for the tests.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Instead of enabling Bluetooth by default on nRF5x boards, only enable
the controller if Bluetooth has been enabled by the applicaiton.
Fixes#5454Fixes#12215
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Configure RTC on nucleo_f746zg.
It is supported through counter RTC API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable testing of counter (COUNTER_{D}TMR_CMSDK) on mps2_an385 and
enable timers on v2m_beetle (TIMER_{D}TMR_CMSDK).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CMSDK Dual Timer can be used as a timer or as a counter.
The unified interface proposed in #8340 unifies counter.h and rtc.h to
provide a common interface.
This patch modifies the timer implementation of the dual timer to
make it compliant with the new proposed interface.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CMSDK Timer can be used as a timer or as a counter.
The unified interface proposed in #8340 unifies counter.h and rtc.h to
provide a common interface.
This patch modifies the timer implementation of the single timer to
make it compliant with the new proposed interface.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enabled EPIT (Enhanced Periodic Interrupt Timer) in Cortex-M4 core
of Udoo Neo Full board so the counter API could be used there.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add driver support for kinetis ID device.
The length depends on the SoC.
`SIM_GetUniqueId` was not used because the struct would reorder
the ID and makes the driver more complicated because the length
of the struct depends on the SoC.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Adds device tree bindings and nodes for the rocktech lcd module used on
imx rt boards. The use of port, endpoint, and remote-endpoint properties
follow what is currently done in linux, but they are not yet used in
zephyr because some additional plumbing is needed in the
extract_dts_includes.py script.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Always link firmware built for nrf9160_pca10090ns into the
code-partition defined in DT, regardless.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Introduce BOARD_NRF9160_PCA10090NS to differentiate between
secure and non-secure board variants.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
When selecting BT we need to select BT_CTRL for most bluetooth
samples to work correctly.
Let's fix that in the board files.
Fixes the following error when CONFIG_BT is selected:
zephyr/drivers/bluetooth/hci/h4.c:463:30:
error: ‘CONFIG_BT_UART_ON_DEV_NAME’ undeclared (first use in
this function)
h4_dev = device_get_binding(CONFIG_BT_UART_ON_DEV_NAME);
^~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Michael Scott <mike@foundries.io>
Indicate that PWM is supported on several Nordic DK boards so that
the pwm_nrf5_sw and pwm_nrfx drivers are covered by CI builds.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable HW PWM driver instead of the SW one on nRF SoCs where the PWM
peripheral is present.
Default PWM instances are also enabled on Nordic DK boards so that it
is possible to build the basic fade_led sample for them without extra
adjustments.
After the above changes are applied, some configuration alterations
in basic samples blink_led and fade_led become no longer needed.
These are removed. And the blink_led sample is corrected so that it
works with the nRF HW PWM driver as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Indicate that watchdog is supported on several Nordic DK boards
so that the wdt_nrfx driver is covered by CI builds.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Changes the default code location from internal itcm to external qspi or
hyperflash. Changes the default data location from internal dtcm to
external sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Changes the default code location from internal itcm to external qspi.
Changes the default data location from internal dtcm to external sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new configuration option to mimxrt10{20,60,64}_evk boards to link
data into external sdram. The default remains to link data into internal
data tightly coupled memory (DTCM).
Note that mimxrt1050_evk is not included because it already has support
for linking data into sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Unlinke nucleo or disco boards, ST-Link Tx/Rx pins used for Virtual
Com Port is not connected to the chip.
Then, console is not available by default and one should use a serial
cable to enjoy console. Adding mention of this fact to the board
documentation and replacing default hello_world example by blinky,
since blinky sample works without any additional hardware.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The disco_l475_iot1 board should be using CONFIG_USB_DC_STM32 as the
Kconfig sybmol.
Also fix a minor typo in a comment in nucleo_f207zg with regards to
CONFIG_USB_DC_STM32
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
From the driver point of view, monochrome controllers from the ssd16xx
family mostly differ by the amount of row and columns that are
supported. If they support more than 256 rows and/or columns the
corresponding size or position is sent using 2 bytes instead of 1 byte.
This patch therefore adds the width-bits and height-bits DT properties
to make this configurable.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that stm32 watchdog should be configured by device tree,
update dts file of boards declaring watchdog support.
Additionally update doc and yaml files.
Add support on some boards that were used to validate the driver
update:
- disco_l475_iot1
- nucleo_f207zg
- nucleo_f429zi
- nucleo_f746zg
- nucleo_f073rz
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert the hci_spi sample to get the SPI and GPIO settings from Device
Tree instead of Kconfig.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert the HCI SPI driver to get the SPI and GPIO settings from Device
Tree instead of Kconfig. The "zephyr,bt-hci-spi" binding is used as
a common one for this purpose ("st,spbtle-rf" is removed), to take
advantage of the new DT_<COMPAT>_<INSTANCE> generated macros and get
rid of related fixups and aliases.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The dts files on these boards had some CONFIG_ defines related to which
memory should be used to hold code. We move this choice out of DTS and
back into Kconfig.
As such, we removed the default setting of 'zephyr,flash' and just
map
CONFIG_CODE_ITCM to:
DT_NXP_IMX_RT_ITCM_0_SIZE
DT_NXP_IMX_RT_ITCM_0_BASE_ADDRESS
CONFIG_CODE_{QSPI,HYPERFLASH} to:
DT_NXP_IMX_FLEXSPI_402A8000_SIZE_1
DT_NXP_IMX_FLEXSPI_402A8000_BASE_ADDDRESS_1
for the mimxrt1050_evk, we remove the default setting of 'zephyr,sram'
and just map:
CONFIG_DATA_DTCM to:
DT_NXP_IMX_DTCM_0_SIZE
DT_NXP_IMX_DTCM_0_BASE_ADDRESS
CONFIG_DATA_SDRAM to:
DT_MMIO_SRAM_80000000_SIZE
DT_MMIO_SRAM_80000000_BASE_ADDRESS
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the how enabling of CONFIG_XIP impacts CONFIG_FLASH_SIZE and
CONFIG_FLASH_BASE_ADDRESS to Kconfig instead of dts.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As we want to remove dts dependency on Kconfig, we had a case based on
CONFIG_BOOTLOADER_MCUBOOT. From a DTS point of view that was just
getting the chosen property 'zephyr,code-partition' set. We can easily
move this to the actual dts files and remove the mcuboot.overlay.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
All Particle mesh devices have an on-board 32 Mibit JEDEC-compatible
flash from GigaDevice. Add bindings to access it.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Previously, only led0 was enabled.
This allows the samples/basic/disco sample to build/run for
this board.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Convert usb_dc_stm32 driver GPIO disconnect to use new defines so we
can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Boot PHY initialization timeout, caching mechanism fixes and networking
buffer descriptors moved to no cache section. Enabled cache management
in networking driver and manual barriers.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Since the lp3943 led driver still supports both DTS and non-DTS
configuration, we update the code to use DT_<COMPAT>_<INSTANCE>
defines for the CONFIG_HAS_DTS_I2C case.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
pinmux dev isn't really used or supported. We only have one driver that
is implmeneted, and that driver isn't ever enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ssd1673 display driver to use new defines so we can remove
the dts_fixup.h code for it. Also dropped "-spi" from compatible.
Fix up references in reel_board dts and sample.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add sam0_rtc_driver that implements system timer API on top of the RTC
and can be used as a replacement for the default systick timer.
Signed-off-by: Martin Benda <martin.benda@omsquare.com>
The pins connected to the sensors and microsd card on board
were mapped to SPI_0 and I2C_0, but for nrf52 chips they
cannot both be used together.
Blip is yet unreleased, so change will not affect anyone really.
Signed-off-by: Tavish Naruka <tavishnaruka@gmail.com>
From the documentation of the SoC and the DevKit it turns out that
there's no hardware PWM controller.
Signed-off-by: Francesco Franchina <cescus92@gmail.com>
Use auto-generated device tree macros in LIS3MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DSL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Added UART4 alternate pin function for L4 µC for PC10 and PC11.
Corrected naming of previously defined UART4 TX and RX defines.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Add support for nrf52840_pca10090, i.e. the nRF52840 SoC on the
pca10090 development kit. The SoC is tasked to route some of the
nRF9160 pins to different components on the development kit.
Additionally, it can be used as a Bluetooth HCI device.
The routing options appear under "Board config" in Kconfig.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
This commit adds the initial documentation information
for board nrf9160_pca10090.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes the Kconfig and DTS board definition
files for nrf9160_pca10090ns board. This Zephyr board shall be
used to build Non-Secure Zephyr applications on nrf9160_pca10090
Dev Kit.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes the Kconfig and DTS files for the
nrf9160_pca10090 board definition. The nrf9160_pca10090 board
shall be used to build Zephyr applications, running in Secure
mode, on nRF9160_PCA10090 Dev Kit.
Additionally, the commit introduces a default Secure and
Non-Secure flash partition configuration for the
nRF9160_PCA10090 board, allowing to use Zephyr for building
both the Secure and Non-Secure firmware images.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
If we are setting the code to be in HyperFlash (CONFIG_CODE_HYPERFLASH)
or QSPI (CONFIG_CODE_QSPI) we should enable
CONFIG_NXP_IMX_RT_BOOT_HEADER.
Update mimxrt1064_evk to use select like other boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board support files for mimxrt1064_evk, the development board for
i.MXRT1064 (CM7) SoC.
- Add pinmux, dts, doc.
- Code can be loaded to SRAM.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
Share lis2dh driver among few accelerometer sensors that has
same register interface: LIS2DH, LIS3DH, LSM303DLHC, LIS2DH12,
LSM303AGR.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Move to using the generated DT_INVENTEK_ESWIFI_ESWIFI0_CS_GPIO_pin and
DT_INVENTEK_ESWIFI_ESWIFI0_CS_GPIO_CONTROLLER defines and drop the
DT_ESWIFI0_CS_GPIOS_PIN & DT_INVENTEK_ESWIFI_ESWIFI0_CS_GPIO_PIN from
dts_fixup.hl
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Supported PWM at pins A0, D3, D5 and D6 which are also Arduino
compatible. Also the onboard red LED can be used with PWM.
The basic/{fade_led, blink_led} samples to apply to this board
seemlessly and operate on the onboard red LED.
Also supported RTC.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
This commit adds the simplest configuration for this Nucleo-144 board
stripped down to the parts that are currently tested.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
Provide through the dts the gpio on which the lsm6dsl INT1 is
connected. Enable also the lsm6dsl trigger mode.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1020_evk
board for LPI2C1 and LPI2C4. LPI2C1 is shared between the Arduino
connector J18 and the WM8960 codec. LPI2C4 is shared between the Arduino
connector J19 and the FXOS8700CQ sensor (non-populated by default).
Updates the board documentation and yaml supported list accordingly.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Enables the mcux ethernet driver and pin muxes on the mimxrt1020_evk
board, the same way it is done on the mimxrt1050_evk board. Updates the
board documentation and yaml supported list accordingly.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
mps2_an385 is enabled for networking -> default networking is SLIP ->
SLIP selects UART_PIPE -> UART_PIPE requires UART_PIPE_ON_DEV defined
-> undefined leads to error on building some samples.
Fix all of these issues.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Board can be emulated in QEMU, so select QEMU_TARGET as required for
various bits of "make run" magic to work.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The board has SMSC LAN9220 (actually as an "IP core" in an
FPGA-emulated SoC). The patch includes DTS bindings for this device.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
board.h does not exist for any of the (official) Nordic nRF
boards. This commit corrects the information about the source
ofthe button and LED definitions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Adds an fxos8700 device tree node to the mimxrt1050_evk. The sensor
interrupt gpios require a board modification to be used and conflict
with Ethernet and LCD signals, therefore their pinmuxes are not
configured.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1050_evk
board. Updates the board documentation and yaml supported list
accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The schematic shows that both INT1 & INT2 from the MMA8652FC are wired
up, update the dts to reflect this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert lsm303dlhc_accel & lsm303dlhc_magn sensor driver to use new
defines so we can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update boards yaml file with arduino_i2c supported option
We exclude disco_l475_iot1 from the x_nucleo_iks01a1 sample since there
are duplicated sensors between the disco_l475_iot1 and shield. Until
Zephyr drivers can handle multiple sensors we need to have this exclude.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables instance 3 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1060_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables instance 2 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1020_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This board has headers for these buses so they should be made available
without requiring special overlays.
Also take advantage of the new Nordic auto-enable for peripherals,
which eliminates the need for special configuration.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Not all boards can get the coverage reports. The report generation
needs minimum of 64KB SRAM. This patch added support for mps2_an385,
qemu_cortex_m3, qemu_x86. This is just a subset. Also the previously
supported board native_posix is included in this patch.
If a board has 64KB RAM, it can generate reports by just
adding HAS_COVERAGE_SUPPORT in Kconfig.board.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Support musca board as a variant, it is a Cortex-M33 based SoC.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Signed-off-by: Minos Galanakis <minos.galanakis@arm.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit renames the CLOCK_CONTROL_NRF5 Kconfig symbol to
CLOCK_CONTROL_NRF. The change is required to aleviates confusion
when selecting the symbol in nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Update nucleo_l073rz to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update doc
- update yaml
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_l053r8 to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f446re to fit with default configuration guidelines:
- add spi support
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update yaml
- disable I2C by default
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f411re to fit with default configuration guidelines:
- add spi support
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update yaml
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f401re to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- disable I2C and PWM by default
- update yaml
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f302r8 to fit with default configuration guidelines:
- remove reference to arduino_serial as Ardiuno D1/D0 are actually
mapped on PA2/PA3 which are already used for ST_Link com port,
hence not available by default for arduino serial
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f070rb to fit with default configuration guidelines:
-configure arduino spi and i2c
-update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
For normal (over-the-wire) mode of CAN sample lowering bitrate to
125000 to ensure reliable transfer on stm32f072b_disco boards
Signed-off-by: Andrei Laperie <andrei.laperie@intel.com>
Increase the size of the MCUBoot flash partition in the fstab-debugger
partition table, to accommodate for the RTT console and logs.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The MCUBoot partition in the default partition table (fstab-stock)
is not meant to accommodate an RTT console, since the board does
not have a SEGGER chip.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Provide a dtsi file that sets up common capabilities for all
Feather-based Particle Mesh devices. Provide additional dtsi files for
some obvious peripheral options.
Remove the xtensa esp32 image: it didn't build, and there's no
indication of how the ESP32 firmware can be updated on the Argon board.
Use particle_argon as the nRF52840 side of the board.
Add Particle Boron support.
Note that dtsi files must be replicated in each board directory until
tooling supports DTS includes from a shared area.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Fix the QSPI and hyperflash nodes to be proper SPI children and expose
the address range for direct access as part of the controller's reg
region.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The mimxrt1020_evk and mimxrt1060_evk boards had invalid jlink device
names. Debugging via 'ninja debug' now works on these boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes a Kconfig typo in the mimxrt1060_evk board that was introduced
when the board was split into separate hyperflash and qspi
configurations.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the default TEXT_SECTION_OFFSET from the board level to the soc
level for the imx rt series. This offset is used to reserve space for
the imx boot header for external xip flash images.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add board support files for mimxrt1020_evk, the development board for
i.MXRT1021 (CM7) SoC.
- Add pinmux, dts, doc.
- Code can be loaded to SRAM.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
By default, after reset SWO signal is not connected to GPIO pin.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin. This
commit adds required initialization code to enable support for SWO
logger. Not all SoC series support the feature.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
lpuart1 is the default port used by ST-Link VPC.
Update board description to match out of box board configuration.
Fixes#12092
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following recent renaming of STM32 UART Kconfig UART symbols,
LPUART was named as UART_LPUART_1.
Rename to LPUART_1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
* Add DTS support for gpio controller driver
Signed-off-by: Ashokkumar B <ashokkumar@zilogic.com>
Signed-off-by: Subash G <subash@zilogic.com>
Signed-off-by: Vishnu K <vishnu@zilogic.com>
Signed-off-by: Vaishnavi D <vaishnavi.d@zilogic.com>
By adding 'aliases' node in SoC .dtsi file it is possible to generate
DT_ defines which specify a logical name rather than relay on module
location on APB bus. E.g. DT_SILABS_GECKO_USART_40010000_LABEL becomes
DT_SILABS_GECKO_USART_USART_0_LABEL. Thus it is possible to remove
dts_fixup.h defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The i2c_atmel_sam3 driver was deprecated at release 1.9, this commit
removes it. Also pinmux_dev_atmel_sam3x driver is removed.
i2c_atmel_sam3 was the last one which depended on it.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Remove configuration parameter CONFIG_BUS_TYPE. Now we may
make use of DT_ST_LSM6DSL_BUS_I2C and DT_ST_LSM6DSL_BUS_SPI
definition to select the bus.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Updated flash partitions to extend supported boot scenarios.
Add support for using Nordic nRF5 bootloader to:
- flash a Zephyr application
- flash a MCUboot image as an application
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The en.high-perf_nucleo-144_mbed.jpg is an empty file.
This causes error when generating PDF documentation
as the tool cannot deal with empty image files.
So replace it with the image with same filename from
nucleo_f765zg, as the images are identical from
the online product description pages.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
interface/stlink-v2-1.cfg and interface/stlink-v2.cfg are wrappers
around interface/stlink.cfg, their inclusion trigger warning which
this change addresses. Besides the warning there is nothing there
except sourcing iterface/stlink.cfg directly.
Signed-off-by: Vasili Slapik <vslapik@gmail.com>
This mode allows the USB driver to use MSI clock as source clock.
MSI PLL-Mode permits +/-0,25% accuracy.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The L476RG does not use the same I2C instance as the other L4 boards.
Correct the pinmux and add the peripheral.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Document CAN support for board nucleo_l432kc and
add can to board yaml "support" section.
Fixes#12052
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fix misspellings in documentation (.rst, Kconfig help text, and .h
doxygen API comments), missed during regular reviews.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Enable by default the following hardware instances in Kconfig:
- ADC_0
- I2C_0
- SPI_1 (SPI_0 for nRF52810)
for all nRF development kit boards having the corresponding DT nodes
enabled. This way there is no need to enable these instances in
particular applications, like samples for sensors or tests for drivers.
I2C_0 and SPI_0 cannot be used simultaneously in most of nRF SoCs,
nRF52810 is the only exception so far (and in this SoC SPI_1 is not
present, hence SPI_0 is enabled for it).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The options selecting nRF drivers are now enabled by default when
an nRF SoC is selected as the build target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fixes board PHY initialization.
ENET_RST and ENET_INT pins are also used as USER_LED/JTAG_TDI and
INT1_COMBO/JTAG_TDO. Initialization needs to set these pins to power and
interrupt for the PHY Transciver. PHY reset works without busy waiting.
Moved pin initialization back to PRE_KERNEL_1 to fix UART bug and busy
wait not required.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Added warnings in documentation, pinmux and dts highlighting a potential
conflict if using SPI_1 and on-board ethernet at the same time.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Added board definitions for nucleo_f756zg. Features include gpio,
pinmux, uart (ST Zio, ST-Link and Arduino Uno v3 interfaces).
Added basic documentation and some soc definitions for the
stm32 f756XX soc.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Updated .dts and pinmux.c to highlight pin conflict on PA7 if ETH and
SPI_1 are selected together without modification.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch cleans up the code in the recently added dts_fixup.h,
restoring the original alignment of the file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The dts.fixup for mps2_an385 contains a wrong setting for the IRQ fixup
for the Dual Timer IRQ.
This patch fixes the symbol included in the generated header.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
To enable the Hyperflash you have to physically modify the board and
this disables the QSPI. Since we plan on removing Kconfig from device
trees, its easier to treat the hyperflash as a separate board config
and thus it will get a dts to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since Voltage Reference block is not supported, the ADC does not work
properly on FRDM-KW41Z. Set voltage reference to alternate source
in frdm_kw41z_defconfig.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
We had SEGGER support enabled by default previously, but the new
Kconfig option CONFIG_USE_SEGGER_RTT needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The lpcxpresso54114_m0 tends to be the secondary core so doesn't
typically have a UART setup for it. We had SEGGER support enabled by
default previously, but the new Kconfig option CONFIG_USE_SEGGER_RTT
needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board support for 96Boards STM32 Sensor Mezzanine board. This board
is one of the 96Boards Mezzanine board which can work standalone or on
top of the 96Boards Consumer Edition boards.
Below are some of the key features of this board:
1. STM32F446VE MCU
2. 96Boards high/low-speed connectivity
3. Arduino™ Uno revision 3 and Grove connectivity
4. Integrated MEMS sensors:
1. LSM6DS3H
2. LIS3MDL
3. LPS22HB
4. MP34DT01-M
5. On-board ST-LINK/V2-1 debugger/programmer
More information about this board can be found in the 96Boards product
page: https://www.96boards.org/documentation/mezzanine/stm32/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The 0.9.5 SDK has support for the Cypress PSoC6 family. Add ablilty to
flash with openocd. I've only tested flashing hello_world on the m0.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To enable the QSPI you have to physically modify the board and this
disables the hyperflash. Since we plan on removing Kconfig from device
trees, its easier to treat the QSPI flash as a seperate board config and
thus it will get a dts to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Zephyr SDK 0.9.4 added OpenOCD support for SiLabs EFR32FG1P SoC. This
commit updates 'Flashing' paragraph of the board documentation to
reflect this change.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Fixes broken user guide and schematics links in nxp board documentation.
Updates remaining nxp.com links from http to https.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Connectors imaages for nucleo_f413zh were actually a reuse of
similar board nucleo_f412zg.
Add dedicated images for nucleo_f413zh.
Fixes#5198
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that we can support the same compatible but different bus types,
update the LSM6DSL support to utilize the same compatible for either I2C
or SPI. We rename the i2c binding file to st,lsm6dsl-i2c.yaml just to
be a bit more clear.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
This patch enables the UART_INTERRUPT_DRIVEN by default for
colibri_imx7d_m4, udoo_neo_full_m4 and warp7_m4 boards.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Reel Board doesn't enable BT by default like many of the nRF52
boards do. So let's make enabling BT a bit easier, by selecting
the BT_CTLR config when BT is enabled. This allows a sample
overlay to merely set:
CONFIG_BT=y
And the end result should be close to correct.
Signed-off-by: Michael Scott <mike@foundries.io>
The nRF51822 and nRF52832 does not support 802.15.4, so remove this
statement from documentation.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
Modify board stm32_min_dev aka "blue pill" led pin assignment in dts
from PB12 to PC13.
This board has a user led connected to PC13.
Sample blinky and similar would run out-of-box without additional
circuit to readout PB12 level.
Tested blinky on corresponding board.
Signed-off-by: Stephen Yi <stephen.jin.yee@gmail.com>
Including Bluetooth to every project unnecessary increase size of the
project, for example hello world sizes:
Memory region Used Size Region Size %age Used
FLASH: 48492 B 1 MB 4.62%
SRAM: 11236 B 256 KB 4.29%
IDT_LIST: 136 B 2 KB 6.64%
after the patch:
Memory region Used Size Region Size %age Used
FLASH: 13344 B 1 MB 1.27%
SRAM: 4004 B 256 KB 1.53%
IDT_LIST: 72 B 2 KB 3.52%
3+ times difference.
PS: It also crashes when 802.15.4 enabled.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Added description how to build, programm and see console output of
hello_world example on cy8ckit_062_wifi_bt_m0 board.
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
The EFM32 Pearl Gecko Starter Kit contains sensors and
peripherals demonstrating the usage of the EFM32PG MCU
family. This patch adds basic support for this board
and is copied from EFM32WG-STK3800.
Signed-off-by: Gil Benkö <gil.benkoe@pm.me>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Adds support for debugging and flashing the mimxrt1050_evk board via
pyocd. Support for this board has not yet been merged in upstream pyocd,
therefore the default in zephyr is left as jlink.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables Networking hardware on i.MX-RT 1050-EVKB board.
Pinout enabled board specific etherenet connection, also pin
initialization was moved later to PRE_KERNEL_2 in order to have
sysclock initialized before.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Enabled Messaging Unit B in Cortex-M4 core of Udoo Neo Full board
so it can use IMX IPM.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Not pretty to change the PAD name from 2 to 1 as the correct
is PAD2 but for the SAMD20 the register value is 1.
Fixes: 6d08958ad5 ("drivers: uart_sam0: move sercom pad info to dts")
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Now that all SPI controllers support DTS we can remove the Kconfig
support for non-DTS options. We also cleanup some defines that should
have be DT_MCR20A_ instead of CONFIG_MCR20A_.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove the ifdef related to CONFIG_FS_FLASH_STORAGE_PARTITION. There
shouldn't be any harm in always having the partition around as we'll
just generate the defines related to and most applications will ignore
them.
Helps get one step closer to have DTS not depend on Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the
nrf52840_pca10056 board and should be maintained and configured
outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the nrf52840_mdk
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move to using Kconfig (like other Atmel SAM drivers do) to specify the
pinmux setting for SAMe70 SoCs. Updated the sam_e70_xplained board to
set the default in Kconfig.defconfig instead of via board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As explained in issue #8915 the STM32F4xx SoC family I2C
does not work well in Standard mode (100KHz). So let's
configure i2c3 in Fast mode (400KHz).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
We should let drivers or board code include soc.h directly so we can keep
board.h to local info for board specific code.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a TICKLESS_CAPABLE kconfig variable which is used by the kernel to
select tickless mode's default automatically on drivers that support
it (rather than having to set the default per-board). Select it from
the ARM SysTick and Intel HPET drivers.
Also remove the old qemu_cortex_m3 default settings which this
replaces.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Turning 'def_bool' in Kconfig.defconfig files into 'default' revealed
three unused symbols (confirmed with 'git grep'). Remove them.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
an explanation of how def_bool->default can reveal undefined symbols.
Removed unused symbols:
- SPI_DW_CLOCK_GATE
- PINMUX_MPS2
- BOARD_XTENSA
Also remove an assignment to the promptless symbol ALTERA_AVALON_SYSID,
in tests/boards/altera_max10/sysid/prj.conf. Assignments to promptless
symbols have no effect.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Added support for ST B-L072Z-LRWAN1 board configuration.
This board uses the same MCU as Dragino-LSN50.
Signed-off-by: Aleksandr Makarov <seems.deviant@gmail.com>
Removed pin 20 which by default is connected to QSPI memory.
Removed conflict with default pin assignment for UART 1.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
Update olimexino_stm32 configuration to match with default
configuration guidelines:
- Configure available UEXT connector which is available
on olimex boards.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Update stm32f469i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
-Update yaml file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f723e_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f769i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32l496g_disco configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update disco_l475_iot1 configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This makes it possible to "ninja debug" to start debugging
towards the onboard debugger of the TB2 board.
Signed-off-by: Endre Karlson <endre.karslon@gmail.com>
The only difference between the F413xH and F413xG is flash memory size.
STMF413xH: 1536 Kbytes
STMF413xG: 1024 Kbytes
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
This enables the USBHS interface on the Atmel SMART SAM E70 Xplained
Board, by adding an entry to the DTS. It also updates the documentation
and mark usb_device as supported for the tests.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Other ST boards have their openocd.cfg support file updated,
but Nucleo L476RG was still looking for board/st_nucleo_l476rg.cfg
and fails with Zephyr SDK 0.9.5.
Signed-off-by: Kiril Zyapkov <k.zyapkov@allterco.com>
Now that the samples use DT generated defines we can remove the
hexiwear_k64 specific ones in board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the Red, Green, & Blue PWM LED info to the device tree. We will use
this in the future for any samples that utilize PWM on these LEDs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
No need to check for BT being enabled. The UART entries will be
available for use if BT is enabled and will do nothing if not.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The wncm14a2a modem is an add-on/shield and not part of the frdm_k64f
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Adding watchdog driver for sam SoC. The current implemntation just
diables the watchdog on device boot.
This PR adds the following support for SAM3X, SAM4S and SAME70
1. Activate processor reset
2. Activate all reset
3. Generate interrupt on watchdog timer expiration.
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since the mb_display driver is specific to the microbit we can move
the GPIO pin defines from board.h into the driver. This lets us remove
one of the few remaining drivers that is including board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the GPIO info for the buttons into the dts, this lets us match what
all other boards are doing. Update some sample & test code to use the
dts generated SW0_GPIO_CONTROLLER define instead of SW0_GPIO_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove some references <board.h> that aren't need or replace them with
<soc.h> where that is the proper include to pull in. Also use "board.h"
instead of <board.h> for how we include the file when its local to the
board code itself.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The frdm_k64f and mimxrt1050_evk boards do not have native bluetooth
support, but rather require an arduino shield to supply a ble controller
over serial hci. Convert the dts to use the newly introduced frdm_kw41z
ble controller shield.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The EFR32™ Mighty Gecko Starter Kit EFR32MG-SLTB004A (a.k.a
Thunderboard Sense 2) contains a MCU from the EFR32MG12P family built
on ARM® Cortex®-M4F processor with low power capabilities.
There is an On-Board J-Link Debugger that presents a virtual COM port
for general purpose application serial data transfer with this
interface and a Mass Storage for firmware flashing.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Combines the lpcxpresso54114_m4 and lpcxpresso54114_m0 boards into one
directory containing both board configurations. This eliminates some
duplicate code and documentation, and better represents the actual
hardware.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In an effort to reduce the number of CONFIG_ defines in dts files, we
can remove CONFIG_MCUMGR_SMP_UART and just always set
'zephyr,uart-mcumgr' as there is no harm to always having this set for
those board dts files that define the property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There were several issues in the dts binding for the ssd1673 display:
* binding file mixed description & generation up together
* Use of BASE_LABEL
* orientation-flipped should have been of type boolean
Update the binding file to reflect these changes, and made associated
changes to dts_fixup.h and driver as needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Flashing the board as described in the docs does not work without having
proper udev rules set. Add documentation for setting those.
Signed-off-by: Johannes Hutter <johannes@proglove.de>
Add a link to the reel board product page at PHYTEC to help people in
locating schematics, etc.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
The Adafruit Feather nRF52 does not have any RTS/CTS signal
connections between the nRF52832 and the on-board CP2104 USB/UART
bridge. Pins 5 and 7 are regular GPIOs.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This enables I2C, SPI, PWM, RTC and USB.
RTC tested on samples/drivers/rtc
USB tested on samples/subsys/usb/cdc_acm
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Partially replaces Kinetis MCUX driver configuration from Kconfig to
Device Tree. Interrputs moved from defines configuration to DT.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Add support for ST Micro Nucleo-64 board with the STM32F302R8
processor. nucleo_f429zi and nucleo_f334r8 were used as
references.
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Introduces the location property and adds the ability to use values
generated by the device tree configuration.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The config file sourced in openocd.cfg is the nuclean_f3 one instead of the one for
the stm32373c.
This makes it impossible to flash the stm32373c evaluation board rev.B:
Error: open failed
in procedure 'init'
in procedure 'ocd_bouncer'
error: command exited with status 1:
/opt/zephyr-sdk/sysroots/x86_64-pokysdk-linux/usr/bin/openocd -s
/opt/zephyr-sdk/sysroots/x86_64-pokysdk-linux/usr/share/openocd/scripts
-f
/home/maudat/repo_upstream/zephyr/boards/arm/stm32373c_eval/support/openocd.cfg
-c init -c targets -c 'reset halt' -c 'flash write_image erase
/home/maudat/repo_upstream/zephyr/samples/basic/blinky/build/zephyr/zephyr.bin
0x8000000' -c 'reset halt' -c 'verify_image
/home/maudat/repo_upstream/zephyr/samples/basic/blinky/build/zephyr/zephyr.bin
0x8000000' -c 'reset run' -c shutdown
Replace the file sourced by stm32f3discovery.cfg to flash successfully.
Signed-off-by: Mathieu Audat <mathieu.audat@savoirfairelinux.com>
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Add sample application for LSM303DLHC, ST MEMS
system-in-package featuring a 3D digital linear
acceleration sensor and a 3D digital magnetic
sensor.
Enable sample to build on stm32f3_disco board
during sanitycheck.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Enable LSM303DLHC, ST MEMS system-in-package featuring
a 3D digital linear acceleration sensor and a 3D digital
magnetic sensor, on stm32f3_disco board.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Sync peripheral mapping documentation with the Nucleo F429ZI board doc
and add missing information about Ethernet and the button.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
This commit is taking care of following stuff:
1. pinmux: STM32F4 micro is using I2S5_CK and I2S_SD to interface with
on-board microphone.
2. default configuration:
- enable I2S5 and configure PLLI2S properly to generate
I2SxCLK = 128MHz.
- enable DMA
Note:
As stated in issue #9028 we needed to take care of a known SPI/I2S bug
implementing the following two actions:
A. APB2 clock has been slowed down to 42MHz.
B. The SPI/I2S clock gpio speed has been set to very_high_speed.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Previously, wifi-enabled samples were not built by sanitycheck for the
cc3220sf_launchxl.
This patch gets the sockets echo sample to build.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The USART fixup in the board dir really are SoC level fixup's. So move
them there and remove the board fixup file since there isn't anything in
it now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The EFM32 Happy Gecko USB-enabled kit contains sensors and
peripherals demonstrating some of the EFM32HG MCU capabilities.
This patch add basic support for this board.
Signed-off-by: Marcio Montenegro <mtuxpe@gmail.com>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Convert over SiLabs based boards to use device tree instead of board.h
to describe buttons & LEDs. There are a few boards that the button
gpio flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As per default board configuration guidelines, this commit updates
96Boards Nitrogen board.
Following changes are done:
- Enable I2C0 and SPI0 in board dts
- Add exposed peripherals in board Kconfig
- Update board yaml
- Remove config option to select board
- Update documentation for UART, I2C and SPI
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As per default board configuration guidelines, this commit updates
96Boards Carbon board.
Following changes are done:
- Enable exposed I2C2 in dts
- Only enable basic peripherals in board defconfig
- Add exposed peripherals in board Kconfig
- Update documentation for SPI
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Convert over NRF based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The commit de78ecd "arm: beetle: Use device tree for IRQs" introduces
a regression related to UART1 IRQ.
On arm beetle the UART1 has IRQ number 2.
This patch restores the functionality modifying the arm beetle device
tree file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Some of the headers referenced in the pinmux.c file don't exist. Match
the includes that the lpcxpresso54114_m4 pinmux.c file uses.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add i2c/spi/gpio to the supported list to enable the CI to correctly
run the 96b_argonkey board sample.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch is equivalent to 7b0ce85242,
but applied to buttons. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The device name was missing for the lsm6dsl sensor in the 96b_argonkey
dts fixup, causing build warnings in tests/drivers/build_all.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
added sam4s16b, sam4s8c, sam4s8b, sam4s4c, sam4s4b,
sam4s4a, sam4s2c, sam4s2b and sam4s2a.
Used the same order as in the data sheet and code structure
equal to same70. Updated the sam4s_xplained board to match
the altered .dtsi location of the specific SoC.
Signed-off-by: Vincent van der Locht <vincent@vlotech.nl>
This patch is equivalent to 7b0ce85242,
but applied to more boards. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_PINS and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled gpio drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_GPIO_DEVICE and
HAS_DTS_GPIO.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_DEVICE and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Argonkey board building has been recently broken by a LSM6DSL sensor
driver fix (see commit: a013ce3bf0).
The board configuration file must now enable HAS_DTS_GPIO_DEVICE macro
instead of HAS_DTS_SPI_DEVICE.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F7 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F3 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F2 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the L4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the L0 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F1 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F0 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enable USB on nucleo_f249zi.
Update clock to allow precise USB clock.
Tested on samples/subsys/usb/cdc_acm
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enables instance 3 of the lpuart driver, adds dts fixups, and configures
pinmuxes to use bluetooth hci on the mimxrt1050_evk board. Updates board
documentation accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The i2c drivers now consistently select HAS_DTS_I2C, so we no longer
need to select it at the board level.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add board support files for mimxrt1060_evk, the development board for
i.MXRT1062 (CM7) SoC.
- Add pinmux, dts, doc.
- External QSPI flash hasn't been configured yet. So code can be loaded
to SRAM for now.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
The i2c_slave_api test was not getting executed on the nucleo_f091rc
board due to a missing supported features list.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Cleanup unused leftover from shield development.
These flags are not actually useful, nor used as dts connectors
are sufficient to control board to shield binding is
operational and dtc provides meaningful error message
when this is not the case.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This change aims at fixing 'unit_address_vs_reg' warning in
STM32 based boards.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for led nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@xx' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The nrf52840_pca10056 defconfig apparently started off as a copy of the
one for nrf52840_pca10040 and one comment was forgotten to be adapted
accordingly.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
This patch adds support of the SAMD21 XPlained board. The board has a
similar pinout to the SAMD20 XPlained with a different pin-mapping.
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Added cy8ckit_062_wifi_bt_m4 board configuration to build FW for CM4
core.
CM4 core does not start itself, it have to be started by CM0+ FW.
Signed-off-by: Nazar Chornenkyy <nazar.chornenkyy@cypress.com>
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
This patch changes the behavior of the sensor. The sensor
will remain in sleep mode after initialization and will only
run the measurements once when sample_fetch is called.
This optimizes the power consumption of the sensor as it
stays in sleep mode most of the time.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This change aims at fixing 'unit_address_vs_reg' warning in
STM32 based boards.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for button nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit removes all MPU-related (ARM_CORE_MPU and NXP_MPU)
options exept ARM_MPU, which becomes master switch controlling
MPU support on ARM.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The HAS_SYSMPU option is just selecting NXP_MPU option,
which could be also controlled through menuconfig.
This commit removes the HAS_SYSMPU option and replaces
its usage by NXP_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The ARM_MPU_IMX_RT option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the ARM_MPU_IMX_RT option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The ARM_MPU_NRF52X option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the ARM_MPU_NRF52X option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The ARM_MPU_ENABLE option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the ARM_MPU_ENABLE option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The STM32_ARM_MPU_ENABLE option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the STM32_ARM_MPU_ENABLE option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Enables an instance of the lpspi peripheral, configures the pinmuxes,
and updates the board documentation accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We get the following warning when building nrf52810_pca10040:
Warning (avoid_unnecessary_addr_size): unnecessary
#address-cells/#size-cells without "ranges" or child
"reg" property in /buttons
Remove #address-cells/#size-cells since they aren't needed for gpio_keys
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When we fixed the missing reg property in the cpu node, we forgot to
add #address-cells & #size-cells for the node.
This fix the following warnings we get:
Warning (reg_format): "reg" property in /cpus/cpu@0 has invalid
length (4 bytes) (#address-cells == 2, #size-cells == 1)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get the following warning when building nrf52810_pca10040:
Warning (avoid_unnecessary_addr_size): unnecessary
#address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys
Remove #address-cells/#size-cells since they aren't needed for gpio_keys
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /flash: node has a reg or ranges
property, but no unit name
or
Warning (unit_address_vs_reg): /memory: node has a reg or ranges
property, but no unit name
Fix by adding unit address that is missing to flash & memory nodes.
Additionally the Silabs memory nodes didn't have a compatiable or
device_type, so add those properties as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /cpus/cpu@0: node has a
unit name, but no reg property
Fix by adding reg property to missing cpu nodes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /gpio_keys/joystick@0:
node has a unit name, but no reg property
Fix by dropping the unit address and renaming the node names to include
more information about the gpio_key.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update all supported features and peripherals in the official set of
boards from Nordic Semiconductor.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_NRF51822_QFAA
CONFIG_SOC_NRF51822_QFAB
CONFIG_SOC_NRF51822_QFAC
CONFIG_SOC_NRF52810_QFAA
CONFIG_SOC_NRF52832_QFAA
CONFIG_SOC_NRF52832_CIAA
CONFIG_SOC_NRF52832_QFAB
CONFIG_SOC_NRF52840_QIAA
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_SAME70*
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have a common DT_SIZE_K macro use it instead of defining
__SIZE_K eveywhere. We also have DT_SIZE_M, so use that in a few
places as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_EFM32WG990F256
CONFIG_SOC_PART_NUMBER_EFR32FG1P133F256GM48
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_CC3220SF
CONFIG_SOC_MSP432P401R
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
UART pins (TX, RX, RTS, CTS) are now configured in DTS files.
RTS and CTS definitions are optional. If flow control is enabled
and RTS/CTS pins are not defined, then compiler will issue
an error message.
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
The LEDs, buttons and necessary aliases are now configured via dts.
This commit breaks the samples under boards/nrf52/mesh:
- onoff-app
- onoff_level_lighting_vnd_app
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The LEDs, buttons and necessary aliases are now configured via dts.
This commit breaks the sample under samples/boards/nrf52/power_mgr.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
This patch adds USB capabilities to the stm32f4 discovery board.
As the board has a MicroUSB port that I would like to use as stdout I
just added USB. The needed entry within pinmux.c is already there but
USB was missing in the dts file and documentation.
I tested it with the upcomming commit.
Signed-off-by: Alexander Polleti <metapsycholo@gmail.com>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
When I2C and SPI are not used (such as when building a simple
bootloader for this target), the current Kconfig is generating a fair
bit of warning spew. Clean it up by moving some explicit _defconfig
settings into defaults.
Signed-off-by: Marti Bolivar <marti@foundries.io>
The version of OpenOCD provided by Zephyr SDK is too old and does not
contain support for EFR32FG1P chip. This patch assumes that user
compiles and installs the newest version of OpenOCD.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This config is only valid for kinetis boards. Fixes the Kconfig warning:
warning: the choice symbol OSC_EXTERNAL (defined at
arch/arm/soc/nxp_kinetis/Kconfig:53) was selected (set =y), but no
symbol ended up as the choice selection.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The LPCXpresso54114 command line example was using a wrong board
name which has been renamed after adding the support for the
Cortex-M0+ core.
Fixes#9649
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
This adds to the adc_api test board-specific configurations
for the following boards:
- nrf51_pca10028
- nrf52_pca10040
- nrf52840_pca10056
"adc" is indicated as supported in the yaml files for these boards
so that they are included in sanitycheck.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
ADC nodes are enabled in DTS for the following nRF development kits:
- nrf51_pca10028
- nrf52_pca10040
- nrf52_pca20020
- nrf52810_pca10040
- nrf52840_pca10056
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use Kconfig specific object "named choices".
Aim is to allow to define config choices selection in Kconfig.*
files instead of _defconfig and hence allow to keep flags
activation conditional.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that the corresponding flash definitions have been added to the DTS,
it's possible to enable the nvs sample in the NUCLEO-L432KC board.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch adds DT description of generic storage flash partition using
the last 16kB of flash when CONFIG_FS_FLASH_STORAGE_PARTITION is
defined. This can be used for FCB or NVS filesystems.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use the correct pyOCD target type for the NRF52840.
This fixes b92436a13f.
Tested with: Atmel ICE Debugger
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Removes the platform whitelist, leaving just the depends_on/supported
pattern to select which platforms the sample can run on.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add support for using non-jlink programmers through pyOCD.
Tested with: Atmel ICE Debugger
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add support for using non-jlink programmers through pyOCD.
Tested with: Atmel ICE Debugger
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This patch is to add support for the WaRP7 board which has an i.MX7
Solo SoC.
The Zephyr is running on the Cortex M4 core and the following features
were validated on this board:
* GPIO: User Switch detection and sensors interrupt
* UART: Zephyr console
* I2C: Communication with fxos8700 and fxas21002 sensors
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
PR #8729 removed the old GPIO_NRF5 driver in favor of an
nrfx-based one. The reel_board still references the old one,
causing CI failures.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As reported in issue #9494, BT samples are using the off-chip
UART-based BT controller on 52810. But the on-chip BT controller is
supported on 52810, so this is the reasonable default when BT is
enabled.
This patch enables BT_CTLR by default when BT is enabled.
This resolves#9494.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
I removed GPIO configuration from board files and enabled them
as default in driver Kconfig file. All boards had GPIO ports
enabled that is why I decided to enable it by default.
Power management example was changed to use new driver.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
This patch adds support for Ethernet in the STM32F2 family of
microcontrollers and enables it for the the Nucleo-F207ZG.
Signed-off-by: Daniel Egger <daniel@eggers-club.de>
The old GCC ARM Embedded website on launchpad
(https://launchpad.net/gcc-arm-embedded) has been superseeded by the new
GNU Arm Embedded one
(https://developer.arm.com/open-source/gnu-toolchain/gnu-rm).
This also means a change of name from "GCC" to "GNU". Reflect this in
the enviroment variables so that the proper term is used henceforth.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
A bug in the jlink application made it impossible to use OpenSDA
firmware with the mimxrt1052 device name, so we used the generic
Cortex-M7 device name as a workaround. This bug was fixed in jlink
V6.32h (2018-07-05), so now we can use the more specific device name.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface for the nRF52840-DK board (nrf52840_pca10056).
They include the following settings when MODEM_WNCM14A2A is selected:
- UARTE1 pin setup
- DTS / DTS fixup additions for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface instead of ethernet.
They include the following settings when MODEM_WNCM14A2A is selected:
- UART 2 setup
- Avoid ETH_0 setup due to pin conflicts
- DTS addition for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
This enables the cc3220sf_launchxl to automatically
reconnect to the last good known access point (AP).
This method avoids the need to:
- perform a wifi scan for access points on bootup (saving power);
- include hard-coded SSID/passwords in the wifi application.
- include the wifi shell in the wifi application.
- rely on more complex provisioning methods;
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Enable the support for the 3 I2C buses of the STM32F723E-DISCO board,
connected respectively to the WM8994, the Arduino V3/STMOD+ and the
touch panel.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Due to bug #9054 this boards is being disable from sanitycheck
temporarily.
Revert when the board is fixed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adds support for the nrf52840_pca10059 board.
The flash partitions are configured to allow migrating from
the stock bootloader to MCUBoot.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
After running some tests which enable assert macro I found some issues
with the i.MX UART configuration.
This patch configures the Tx Fifo Watermark and Modem Mode accordingly.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Addition of a Flash partition to the 'frdm_k64f.dts' file in the
currently existing 'Application Area' (Partition Location: 0x0001e000
Partition Size:0x00002000). This partitioned area can be used as a FCB
for Bluetooth and other applications.
Signed-off-by: Arjun Warty <arjun.warty@nxp.com>
This commit enables the use of UARTE on Nordic nrf52810_pca10040
development kit. It also instruct console to use UARTE (instead
of RTT).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The Adafruit Feather nRF52 is based on an Nordic Semidconductor nRF52832
based development board with UART, SPI, LED and onboard lithium polymer
battery charger.
Signed-off-by: Florian Gärtner <florian.gaertner@ledcity.ch>
The EFR32 Flex Gecko Wireless Starter Kit contains sensors and
peripherals demonstarting the usage of the EFR32FG1P SoC
family. This patch add basic support for this board.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Add first set of boards which can be built with xtools, this will
include all boards at some point, so we might need a better way to
whitelist toolchains that does not include changing every single board
definition file. For now enabling those needed for testing the new
toolchain.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch adds basic support and for the STM32F769I-DISCO board
with GPIO, USART support. Two USARTs are enabled.The GPIOs are
configured for the 4 LEDs and one button on the board.
Signed-off-by: Yong Jin <jinyong.iot@foxmail.com>
Set HAS_ARDUINO_XXX flag to state boards is compatible with this
connector. It will enable use of shields that requires these flags.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Have qemu_cortex_m3 use the traditional multiqueue scheduler by
default, to be sure it gets test coverage.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This patch adds basic support and documentation for the STM32F723E-DISCO
board, with GPIO, USART, I2C and USB support. Two USARTs are enabled,
the VCP one for the console and the Arduino one. The GPIOs are
configured for the 3 LEDs and the button available on the board.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Unconditional CONFIG_BT_SPI_BLUENRG flag activation was generating
a systematic warning.
Move it in Kconfig.defconfig file to avoid the warning
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The ArgonKey board has 12 leds controlled by TI LP3943 led
controller. Add the support in the BSP.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Since the PCA10040 contains the required DC/DC circuitry, enable it by
default while keeping it configurable. This reduces power consumption
during radio activity.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the PCA10040 contains the required DC/DC circuitry, enable it by
default while keeping it configurable. This reduces power consumption
during radio activity.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Adding new implementation of logging subsystem. New features
includes: support for multiple backends, improving performance
by deferring log processing to the known context, adding
timestamps and logs filtering options (compile time, runtime,
module level, instance level). Console backend added as the
example backend.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
The patch contains basic code support, documentation, dts
file and openocd configuration for STM32F746G discovery board.
This patch related to the issue #6982.
Signed-off-by: Yurii Hamann <yurii@hamann.site>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that for any of the removed properties though.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Segger provide a firmware makes the ST-LINK on-board compatible with
J-Link OB, allowing users to take advantage of most J-Link features
such as RTT(Real Time Transfer).
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
The nRF52810 is a low-cost variant of the nRF52832, with a reduced set
of peripherals and memory. This commit adds Bluetooth controller support
for it.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit selects HAS_DTS_I2C in bbc_microbit board definition.
It fixes issues similar to issue #8511 for bbc_microbit board
Signed-off-by: Mandar Chandrakant Thorat <mandar.chandrakant.thorat@intel.com>
The commit modifies the I2C-related defines in nrfx
configuration to comply with the updates in (57e3644).
It also modifies the i2c configuration in DTS for board
nrf52810_pca10040 to reflect the nRF52810 capabilities.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit moves the definitions for the LED and Buttons
supported in nrf52810_pca10040 DK in DTS from board.h. Aliases
are kept in board.h to make basic examples pass.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds a compile-time directive for the
nrf52810_pca10040 board that instruct nRFx to perform
certain board initialization. The directive is needed
as nrf52810_pca10040 mirrors the nrf52832 DK hardware.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The nRF52810 is a low-cost variant of the nRF52832, with a reduced set
of peripherals and memory. This commit adds basic support for it in the
arch SoC and dts folders.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Ioannis Glaropoulos <ioannis.glaropoulos@nordicsemi.no>
Since Nordic does not offer an nRF52810 Development Kit and instead
recommends using the nRF52 DK (nRF52832 based), add a board that
enforces the limitations of the nRF52810 but is designed to be flashed
onto the actual nRF52 DK hardware.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Ioannis Glaropoulos <ioannisg.glaropoulos@nordicsemi.no>
In order to avoid auto-selection by Kconfig, the board needs to define
the specific IC that it contains, in this case an nRF52832.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update the link to SAM3X8E datasheet and
update the minicom command to use sudo as
accessing the serial port requires root permission
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Fixes#8391
Enables the i2c drivers for these boards.
Required to enable i2c with these boards.
Tested samples/sensor/tmp112 for nrf52_blenano2
with i2c enabled.
Signed-off-by: Mandar Chandrakant Thorat <mandar.chandrakant.thorat@intel.com>
Currently tests/benchmark/footprint build is failing for
nrf52_pca20020 board. In minimal configuration, all modules are
disabled, including GPIO, because of that defines related to GPIO
are missing in board.c file and compilation fails.
To solve it, I selected GPIO to be always turned on for
nrf52_pca20020 board.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
SDA and SCL pins can now be configured through DTS.
Pins on development kits have been assigned according to arduino
headers.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
The UDOO Neo Full single board computer configuration supports
the following hardware features on the Cortex M4 Core:
+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=====================================+
| NVIC | on-chip | nested vector interrupt controller |
+-----------+------------+-------------------------------------+
| SYSTICK | on-chip | systick |
+-----------+------------+-------------------------------------+
| UART | on-chip | serial port-polling; |
| | | serial port-interrupt |
+-----------+------------+-------------------------------------+
| GPIO | on-chip | general purpose input/output |
+-----------+------------+-------------------------------------+
The default configuration can be found in the defconfig file:
boards/arm/udoo_neo_full_m4/udoo_neo_full_m4_defconfig
Other hardware features are not currently supported by the port.
Connections and IOs:
The UDOO Neo Full board was tested with the following pinmux
controller configuration.
+---------------+-----------------+---------------------------+
| Board Name | SoC Name | Usage |
+===============+=================+===========================+
| J4 RX | UART5_RX_DATA | UART Console |
+---------------+-----------------+---------------------------+
| J4 TX | UART5_TX_DATA | UART Console |
+---------------+-----------------+---------------------------+
The board has been tested with the following samples.
- samples/hello_world
- samples/basic/blinky
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Both variables were used (with the same value) interchangeably
throughout CMake files and per the discussion in GH issue,
ZEPHYR_BASE is preferred.
Also add a comment with explanation of one vs. the other.
Tested by building hello_world for several boards ensuring no errors.
Fixes#7173.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
This commit enables CAN on the STM32L432.
Tested on nucleo l432ck with external transceiver and loopback mode.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This adds basic support for declaring gpio nodes in dts for nrf52.
The dts.fixup provides mapping for the generated defines to the config
defines currently used by the nrf gpio driver.
Existing boards that use nrf52 are updated.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Added a hidden Kconfig option in arch/arm/soc/nordic_nrf
which is selected by selecting DC/DC circuitry being present
in the board.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
UART driver renamed to keep the same convention as SPI and TWI drivers.
All substrings: "UART_NRF5" in defines renamed to "UART_NRFX_UART".
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
As the nRF52840 supports 802.15.4 natively, we should default y
for IEEE802154_NRF5 if IEEE802154 is enabled.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
commit 53a924b390
clobbered parts of
commit 9d2f370ddb
which included changes to make cc3220sf_launchxl XIP by default.
This patch reverses the clobber.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The choice symbol LSM6DSL_EXT0_LIS2MDL was given a 'default' in
Kboards/arm/96b_argonkey/Kconfig.defconfig, but 'default' has no effect
on choice symbols, triggering a warning from Kconfiglib.
Instead of adding a default to the choice symbol, change the default of
the 'choice' itself by giving it name and adding the default in
Kconfig.defconfig.
This requires that we remove the default on the "base" definition of the
'choice', due to some messiness related to the Zephyr-specific
prefer-later-defaults behavior (see the 'Zephyr-specific Kconfig
behavior for defaults' section in the Board Porting Guide). Choices were
overlooked when that patch was added to the C tools, meaning choices
still prefer earlier defaults. The crux is that Kconfig.defconfig files
are included last.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These symbols were removed in commit 311e6b9e3e ("arch: arc: Use DTS
for all ARC SoCs"). The settings should come from DTS now.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fixed the incorrect usage of CONFIG_FLASH in the defconfig.
This CONFIG_FLASH is used to enable the flash driver only.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Fixed the incorrect usage of CONFIG_FLASH in the defconfig.
This CONFIG_FLASH is used to enable the flash driver only.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Fixed the incorrect usage of CONFIG_FLASH in the defconfig.
This CONFIG_FLASH is used to enable the flash driver only.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The ST Nucleo L432KC board only has a reset switch and not user switch.
It has a single user LED connected to PB3, and called LD3 in the ST
documentation.
This patch fixes the corresponding device tree definition. At the same
time also it also fixes the documentation, where the name of the power
and user LEDs are swapped.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
TI literature site has links which are automatically updated to point
to the latest versions of pdf documents.
Use those instead of the hardcoded URLs.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Update board docs to reflect simpler method of flash/debug as
cc3220sf is now by default an XIP platform.
Include installation instructions for TI OpenOCD as a pre-requisite.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Previously, the cc3220sf platform could only be flashed using
TI UniFlash (or CCS) tools, requiring unique instructions.
Also, these procedures were not integrated with the standard Zephyr
build targets: 'flash', 'debug', 'debugserver'.
After installation of a TI OpenOCD v1.10 release, and other
one-time board setup, flashing and debugging can now be done
via OpenOCD/gdb, using the standard Zephyr build targets per
the Zephyr Application Development primer.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Previously, there was no easy command-line solution for loading
a Zephyr program to (internal) flash.
So, the default development method was to load via gdb/openocd
to SRAM and debug from there, thus making the cc3220sf platform
non-XIP (CONFIG_XIP=n) by default.
With new openocd v 1.10 updates from TI (git.ti.com/sdo-emu),
the image can now be flashed and debugged via gdb/openocd,
so the default will be changed to XIP (CONFIG_XIP=y).
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
As mentioned in
https://github.com/zephyrproject-rtos/zephyr/issues/7873, these Kconfig
symbols never existed. Remove the assignments to them.
Keep the dead code that's guarded by them for a while. I don't know if
this board is used.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Supposed to come from DTS. The Kconfig symbol was removed in commit
311e6b9e3e ("arch: arc: Use DTS for all ARC SoCs").
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Setting of CONFIG_HEAP_MEM_POOL_SIZE was done in the board defconfig
because open-amp was doing recursive builds and setting it the
defconfig made sure all builds were consistent. However, now that we
don't do recursive builds this will get properly picked by from the
sample specific conf file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The {FLASH,SRAM}_BASE_ADDRESS Kconfig symbols were removed in commit
311e6b9e3e ("arch: arc: Use DTS for all ARC SoCs"). These settings are
supposed to come from DTS now.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
USB IP is not directly available on disco_l475_iot1 and requires
some HW modifications to get it enabled.
Remove this USB pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
During transition from native to ll based clock_control
driver, a typo was introduced in PPL source selection flag.
Fix this.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The defconfig has CONFIG_SOC_MKL25Z=y, however CONFIG_SOC_MKL25Z doesn't
exist and should have been CONFIG_SOC_MKL25Z4, However its not
necessary to define this at all since it implied by the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We had a comment related to the #endif for CONFIG_USB_DC_STM32 however
the comment said CONFIG_USB_DC_STM, so fix it to match the ifdef.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
CONFIG_BOARD_STM32_NUCLEO_{L432KC,L476RG} where set in the respective
board defconfig files, however these symbols don't exist. We can just
remove them from the defconfig as we'll get the board Kconfig symbol
defined by default when selecting that board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The kl25z does not have the same spi hardware as the k64f and therefore
cannot use the same spi driver. Remove all references to spi for the
kl25z soc and frdm_kl25z board until we have a valid spi driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This commit adds a sample application using OpenAMP for remote procedure
calls on the LPCXpresso54114. It is adapted from the RPMsg-Lite sample
application added in PR #5960, and uses the IPM driver to provide
interprocessor interrupts.
Signed-off-by: Kristian Klomsten Skordal <kristian.skordal@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The current method of setting the openocd runner arguments works for
direct invocation from the command line, but the values that are
written to the CMake cache are not properly separated and are
difficult to parse, due to the fact that in several cases, option
values contain spaces.
Adjust these runner arguments so that the options and their values are
separate list items. This makes it possible to parse them accurately
from the CMake cache.
No functional changes.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Use the named choices feature introduced by PR #6966
and configure LSM6DSL on ArgonKey board.
The two named choices introduced in LSM6DSL are:
- LSM6DSL_BUS_TYPE (default LSM6DSL_I2C)
- LSM6DSL_TRIGGER_MODE (default LSM6DSL_TRIGGER_NONE)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch adds dts support to lps22hb/hts221/vl53l0x
I2C sensors as well as lsm6dsl SPI sensor.
Since some info, like gpio for irq triggering or SPI bus
characteristics, may be provided through dts, they need
to be made optional in the LSM6DSL driver by usage of
macros like HAS_DTS_SPI_PINS or HAS_DTS_SPI_DEVICE.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add MCUX IPM sample application. It can be run on lpcxpresso54114
board at the moment.
We first build the slave core image out of the remote/ dir than the
primary core image is build which includes the slave core image.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add driver for MCUX mailbox which can be used for lpcxpresso54114
and other lpc and kinetis socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add a board port to allow creation of "firmware" code that will run on
the slave core (Cortex-M0+).
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Updates documentation for the frdm_k64f, hexiwear_k64, and usb_kw24d512
boards to reflect that they now support a watchdog driver. Updates the
board yamls similarly for sanitycheck.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds the configuration, driver, and HAL changes required
to implement a MCUX based RTC driver for the NXP Kinetis KW41Z.
Signed-off-by: Andy Gross <agross@kernel.org>
This patch adds some DTS information to flesh out the NXP Kinetis
based RTC blocks. DTS fixups were added as well to match up the driver
usage to the DTS output.
Signed-off-by: Andy Gross <agross@kernel.org>
Kconfig keyword GPIO_AS_PINRESET is common for whole nrf52 series.
This patch move it to the series Kconfig.soc file.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add use-prop-name to disconnect-gpios property in st,stm32-usb
yaml, in order to generate friendly name for the definitions.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
In order to run the Simple Management Protocol (SMP) over UART, a DTS
symbol named uart-mcumgr needs to be defined on the board. Enable this
for all Nordic Development Kits.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As part of the prep to support the M0+ core on lpcxpresso54114, we
rename the lpcxpresso54114 board port to lpcxpresso54114_m4 to be
explicit.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename various SoC related defines and files from just being LPC54114
to LPC54114_M4. This is in prep for supporting a build for the second
core on the LPC54114 (the Cortex-M0+).
* Renamed Kconfig SOC_LPC54114 to SOC_LPC54114_M4
* Renamed Kconfig.defconfig.lpc54114 to Kconfig.defconfig.lpc54114_m4
* Introduced nxp_lpc54xxx_m4.dtsi based on nxp_lpc54xxx.dtsi
* Moved some pinmux related defines into SoC code.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use DT to generate defines for irq and reset gpios in bluetooth
controller node.
Define a bt alias to allow generation of defines with friendly
names.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Adds dts bindings for the mcr20a wireless transceiver. The frdm_k64f
board supports the mcr20a via an Arduino shield, therefore the dts node
is added to the board dts. The kw2xd is a SiP and thus the mcr20a dts
node is added to the soc dts.
The networking samples using prj_frdm_k64f_mcr20a.conf have been broken
since the refactoring of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Configures the frdm_kw41z board to mux spi signals on pins PTC16-19.
Updates the board document to reflect that spi is supported on these
pins.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts bindings for the fxas21002 interrupt pins to all boards that
have this sensor.
The fxas21002 driver is currently only aware of one sensor interrupt
pin, therefore the routing of INT1 or INT2 to the driver is handled in
each board's dts.fixup.
The fxas21002 sample application has been broken since the refactoring
of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts bindings for the fxos8700 interrupt pins to all boards that
have this sensor. The frdm_k64f and hexiwear_k64 connect both sensor
interrupt pins to the mcu, but the frdm_kw41z connects only one.
The fxos8700 driver is currently only aware of one sensor interrupt pin,
therefore the routing of INT1 or INT2 to the driver is handled in each
board's dts.fixup.
The fxos8700 sample application has been broken since the refactoring of
the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add cs, irq and reset gpios description in spbtle controller
node and use generated defines instead of Kconfig symbols.
Define a bt alias to allow generation of defines with friendly
names.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Indexed defines were systematically generated even when there
was only one element to generate.
So we ended up generated a lot of _0 defines.
Then we needed to generate aliases to these _0 indexed defines,
in order to get useful defines.
For instance:
#define GPIO_LEDS_0_GPIO_FLAGS_0 4
#define GPIO_LEDS_0_GPIO_PIN_0 5
#define GPIO_LEDS_0_GPIO_FLAGS GPIO_LEDS_0_GPIO_FLAGS_0
#define GPIO_LEDS_0_GPIO_PIN GPIO_LEDS_0_GPIO_PIN_0
This commit allows to generate _0 indexed define only if a
property has more than one elements to define.
Aliases generation to _0 indexed defines are also removed.
Note: IRQ are left untouched since this is frequent to handle
multiple IRQs in a driver
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The disco_l475_iot1 board uses the vl53l0x sensor in XSHUT pin
master control configuration mode. So, it has to explicitly
enable it now.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Adds a board-level config option to select whether the code gets linked
into internal instruction tightly coupled memory (ITCM), external
hyperflash, or external qspi flash. The default is ITCM.
Note that we are not yet building an image vector table (IVT) into the
image, therefore the zephyr binary is not bootable by the SoC ROM as-is.
However, the DAPLink firmware prepends an IVT to the image when you use
its drag-and-drop feature to program flash, and this results in a
bootable zephyr application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds flexspi and semc memory controllers to the i.MX RT SoC. Adds
hyperflash, qspi, and sdram external memories to the mimxrt1050_evk
board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Previously, when !CONFI_XIP, BOOTLOADER_SRAM_SIZE was defaulted
to 16 (K), reducing the size of SRAM available for the program.
Also, though it has no effect, the value for SRAM start in the
dtsi file was incorrect.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The frdm_k64f board document incorrectly listed spi signals on PTCD
pins, which don't exist. They should be on PTD pins.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds DT description of generic storage flash
partition. This fixes issue #7227.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
FS_FLASH_MAP_STORAGE keyword enables the storage partition,
but it was depend on flash_map module which is unused by
NFFS. This patch makes it independent thanks
to it is possible to enable the storage partition
without flash_map module.
FS_FLASH_MAP_STORAGE was renamed to
CONFIG_FS_FLASH_STORAGE_PARTITION
as it is independent for flash_map.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Following changes are necessary to use LP3943 LED driver present
in 96Boards Neonkey board
1. Enable I2C_3 interface
2. Reduce the speed of I2C_3 bus on 96Boards Neonkey. Due to some
design quirks, on board LP3943 LED driver connected to I2C_3
operates only at Standard speed of 100KHz.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
These are a direct copy from the nrf51_pca10028 board, since it's also
an nRF51 and has the same size flash.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The allowed values for APB2 prescaler are: 1, 2, 4, 8, 16.
Set APB2 prescaler value to 1 in boards defconfig.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The NFFS partition at the end of flash is also useful for any other
file system or even the Flash Circular Buffer (FCB). Rename the
partition from 'nffs_partition' to 'storage_partition' and make it
depend on a new hidden Kconfig entry which the relevant users will
select (such as NFFS and FCB).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
"unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In some BLE use cases, using MSI driven SYSCLK is required.
Rework board Kconfig.defconfig in order to enable use of 2
alternate default clock configurations.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We have been combining imported mcux drivers into a flattened directory
structure to maximize driver reuse, but the introduction of additional
nxp soc families (lpc and imx) to zephyr has introduced driver naming
conflicts. This caused us to rename and modify imported files, such as
fsl_gpio.c/h, to make them unique across all three nxp soc families.
This makes updating the the mcux drivers complicated, especially for the
lpc family.
Reoganize the mcux drivers into soc family subfolders, so we can just
copy all the drivers from an mcux distribution (which is done on an
soc-basis) into the appropriate soc family folder. Undo all of the
naming changes that occurred when lpc and imx drivers were originally
imported. Undo the accidental squashing of the kinetis watchdog and dcdc
drivers that occurred when the imx drivers were introduced.
The drawback to this approach is that we have duplicate files when the
same hw ip modules exist in multiple soc families, however there are
only few cases where this occurs, such as fsl_lpuart and fsl_trng.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes#7137
Enables the i2c drivers for these boards.
Required to enable i2c with these boards.
Tested samples/bluetooth/beacon for nrf52_pca10040
with i2c enabled.
Parameters used for enabling i2c:
CONFIG_I2C=y
CONFIG_I2C_0=y
CONFIG_I2C_NRF5=y
CONFIG_I2C_NRF5_0_GPIO_SCL_PIN=6
CONFIG_I2C_NRF5_0_GPIO_SDA_PIN=7
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.com>
Adds led and button dts nodes to all kinetis boards and removes the
now unused preprocessor macros from board.h.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update names of the configuration entries so that the new nRF SPIS
driver can be used on this board.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The test "net/utils" fails to build on nucleo_f103rb
due to "region `SRAM' overflowed by 8 bytes.
Disabling PWM at the board level to build the test.
Moreover, according to issue #6858, we will only configure
board valuable HW and connectors on board level and the
user should enable what is needed on application level.
Reported-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Underscore ('_') isn't a valid char for alias names based on the device
tree spec. Newer dtc compilers flag this as a warning so lets clean it
up. Replaced '_' with '-' to keep things simple.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The TRNG IP block in the KW41Z is really an entropy source and not
intended to be used as a general purpose random number generator
source. The block has 15 slots to read from and when the last slot
is read it has to regenerate the 15 numbers. This process takes
3-5 seconds and is blocking. The change here is to use the TRNG as
an entropy source to the XOROSHIRO pseudo random number function
and then have the KW41Z use XOROSHIRO for random number generation.
Signed-off-by: David Leach <david.leach@nxp.com>
The Colibri iMX7D Computer on Module with Colibri Evaluation Board
configuration supports the following hardware features on the Cortex M4
Core:
+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=====================================+
| NVIC | on-chip | nested vector interrupt controller |
+-----------+------------+-------------------------------------+
| SYSTICK | on-chip | systick |
+-----------+------------+-------------------------------------+
| UART | on-chip | serial port-polling; |
| | | serial port-interrupt |
+-----------+------------+-------------------------------------+
The default configuration can be found in the defconfig file:
boards/arm/colibri_imx7d_m4/colibri_imx7d_m4_defconfig
Other hardware features are not currently supported by the port.
Connections and IOs:
The Colibri iMX7D Computer on Module with Colibri Evaluation Board
was tested with the following pinmux controller configuration.
+---------------+-----------------+---------------------------+
| Board Name | SoC Name | Usage |
+===============+=================+===========================+
| UART_B RXD | UART2_TXD | UART Console |
+---------------+-----------------+---------------------------+
| UART_B TXD | UART2_RXD | UART Console |
+---------------+-----------------+---------------------------+
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
All boards based on STM32 should use dts for I2C and SPI.
Move CONFIG flags selection from boards to arch and select them
for all STM32 SoCs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We run the same tests over and over again in different qemu
environemnt. Optimize the list to reduce redundant testing of the same
protocols. Picked qemu_x86 because it has userspace enabled.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A Kconfig option is added for setting the initialization priority.
This is done to make the initialization priority requirements in
nrf52_pca20020 board power up sequence clearer.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
A documentanion file is added for Thingy:52. This document only
discusses the currently supported features of the board. The omissions
include the audio features and sensors which don't have a working driver
in tree.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
A new board configuration is added for Thingy:52, also known as
PCA20020. This includes support for some of the on-board sensors, and
other peripherals such as the on-board GPIO expander.
The board power rail sequencing is also implemented, as the rails need
to be powered up in a correct order and before certain device driver
init calls are made.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
The test "net/utils" fails to build on olimexino_stm32
due to "region `SRAM' overflowed by 192 bytes".
Disabling I2C and SPI on board level the test build fine.
Moreover, according to issue #6858, we will only configure
board valuable HW and connectors on board level and the
user should enable what is needed on application level.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
As we have E70 ethernet driver enabled, we need to enable the
generic ethernet L2 driver too so that the ethernet is actually
useful.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The SAM0 SoC was switched to use DTS for SPI configuration. Update
documentation for the SAM0 based boards to use the correct SPI
controller device names.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
As the board has ethernet chip it makes sense to enable the
ethernet support by default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
New revision (SWCU117H) got published and the old one (supposedly
SWCU117G) is no longer available.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Currently, it seems that only boards with smaller amount of RAM
get a value for "ram" property, and very few boards have "flash"
defined. However, to test bigger sample applications, it's helpful
to have these properties universally defined.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Added support for Waveshare BLE400 board.
Tested it with the following samples and confirm it work.
- samples/basic/blinky
- samples/basic/button
- samples/basic/fade_led
- samples/basic/threads
Signed-off-by: Roman Tataurov <diytronic@yandex.ru>
Describe in documentation few methods that can be used by
users to flash the ArgonKey with a binary image.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Move the dts.fixup back to board dir in prep for support mps2_an521.
The memory maps between the two mps2_an385 and mps2_an521 differ greatly
so its easier to just keep the fixup files with the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add initial support for NUCLEO-L073RZ board.
This is a typical Nucleo-64 board, so most files are reused
from already supported Nucleo boards with small changes.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
SoC dts fixups are added and the i2c_nrf5 driver is modified to use
the values generated from the device tree.
The I2C_*_DEFAULT_CFG and I2C_*_IRQ_PRI options are removed from board
defconfigs. Bitrate and IRQ priority are configured using using the
device tree instead.
HAS_DTS_I2C is selected on all nrf5 boards to prevent generation of
conflicting defines from Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
The i2c controller nodes are enabled in the board specific dts files
on boards where the controller was enabled in the board Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
This commit changes the Arduino Zero pinmux configuration to use PA12
as MISO.
According to the schematic, the Arduino Zero provides a SPI bus on
SERCOM4 with the following pads/pins:
- MISO: PA12/pad0 (pin 21)
- MOSI: PB10/pad2 (pin 19)
- SCK: PB11/pad3 (pin 20)
The MISO signal is incorrectly labeled as PB12_S4_SPI_MISO on the
schematic. It should be labeled PA12_S4_SPI_MISO.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Nucleo-64 boards do not have X3 crystal by default, so HSE is clocked
from MCO output of ST-LINK, and CONFIG_CLOCK_STM32_HSE_BYPASS should be
enabled. STM32F0 HSE somehow magically works even without that, but
to do so is the right thing.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Since not all boards enable all devices, we typically have the SoC dtsi
file have a device marked with status = "disabled" and have the
board.dts explicitly enable with status = "ok". Update it so USB on
Atmel SAMD21 work this way.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move IRQ numbers into device tree so we can remove soc_irq.h. We are
already using IRQ defines generated form the DTS so no point in having
soc_irq.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added device tree support to the ARM SBCon I2C controller. We utilize
the compatiable "arm,versatile-i2c" the binding from Linux for the some
peripheral block.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The legacy SPI API was turned back on for the Adafruit Feather M0
Basic Proto when the SAM0 SoC was switched to using DTS for SPI. This
commit turns it back off.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
ArgonKey board is a 96boards sensor hub platform for all 96Boards
compliant family products. The ArgonKey packs a Cortex-M4 chip
together with a set of motion, environmental and ambiental sensors
and can be used as a development platform for many different
applications.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Switch the SoC device tree to define a single entry per SERCOM instead
of one per mode.
Define a Device Tree binding for the SAM0 SPI and use it instead of
Kconfig for enabling / disabaling instances
Switch the Arduino Zero, Adafruit Feather M0 Basic Proto, and
Trinket M0 to use the new defintion.
Add the APA102 LED that's on the Trinket as a test.
Signed-off-by: Michael Hope <mlhx@google.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Changed the default UART used for the console. You used to have to
use wires on the J4 header. Now you can use the UART provided by the
Segger USB composite device.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Fixed the output string in the documentation for
the SAM E70 Xplained. The output for the hello_world
sample wasn't correct.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Support the ST STM32F0DISCOVERY board with STM32F051R8T6 SoC
Tested with:
- `samples/basic/blinky`
- `samples/basic/button`
Includes flash config in `stm32f0_disco.rst` for use with mcuboot
Signed-off-by: Nathan Tsoi <nathan@vertile.com>
The Feather M0 Basic Proto is an Atmel SAMD21 based development board
with USB, UART, SPI, LED and onboard lithium polymer battery charger.
Use of the Adafruit stock photo (adafruit_feather_m0_basic_proto.jpg)
for the board documentation was approved by Adafruit Industries.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
As USB port is present on the board, and pinmux configured,
add USB support in board dts file.
Configure Ethernet oer USB as default net i/f
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
According to STM32-E407.pdf (Revision I, June 2017), CON1 RST is
connected to processor pin #25, not #23.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
The arm qemu platform has limitiations as we get into more complicated
features like userspace support. Add one hardware platform to catch
issues in sanitycheck for development of such features.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/arm/soc/<SOC>/dts.fixup so
we remove duplication in the boards and only have board specific
defines in boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The space referred to in these comments was once truly reserved for
the application: no zephyr partition would ever use it.
Now, though, that's not the case, since NFFS will use these sectors
when enabled.
Just delete the comments.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Let's point users at the latest documentation on flash
partitions from each of the board files, rather than duplicating some
of the information in it.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Move common SoC dts.fixup defines into
arch/arm/soc/atmel_sam/<BAR>/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/arm/soc/nxp_imx/rt/dts.fixup
so we remove duplication in the boards and only have board specific
defines in boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/kwx/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/kl2x/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_lpc/lpc54xxx/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/k6x/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implements interrupt driven UART for the serial driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Move common SoC dts.fixup defines into
arch/arm/soc/ti_simplelink/<BAR>/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Current configuration was choosen to avoid colliding with existing ones
for i2c and uart, but others can be used.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Current configuration was choosen to avoid colliding with existing ones
for i2c and uart, but others can be used (see
drivers/pinmux/stm32/stm32_f0.h)
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Configure SPI using DT for the following STM32 boards:
96b_neonkey
nucleo_f091rc
nucleo_f334r8
nucleo_f401re
nucleo_l432kc
nucleo_l476rg
SPI nodes in <board>.dts file are populated matching boards existing
pinmux default configuration and enabled in Kconfig.defconfig if
SPI is enabled.
For nucleo_l476rg board SPI2 and SPI3 nodes are not yet added, because
of missing pinmux defines.
Fixes#5836
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Commit 247782a7b3 moved the sam0 UART
and SPI configuration into pinmux. Using these drivers without pinmux
causes the kernel to skip the pin configuration.
Tested on arduino_zero.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Remove spurious console code block to fix formatting of the following
zephyr-app-commands directive. While I am here, fix the indentation of
the two zephyr-app-commands directives.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Atmel SAMD21 series was classified too broadly as SAMD.
This patch names it correctly to make room,
for other members of SAMD series
Signed-off-by: Sean Nyekjaer <sean@nyekjaer.dk>
Also pull out the SERCOM pads configuration to defines. Note that the
SAM0 has a two level configuration - a signal (like TX) is mapped to a
pad, and then a pad is mapped to a function on a pin.
Signed-off-by: Michael Hope <mlhx@google.com>
nucleo_f413zh was missing some files to support flash with
openocd. Fix this lack and update doc.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
nucleo_f412zg was missing some files to support flash with
openocd. Fix this lack and update doc.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
CONFIG_I2C_NRF5_GPIO_SDA_PIN and CONFIG_I2C_NRF5_GPIO_SCL_PIN are
replaced with port specific versions. Board defconfigs relying on the
original names are updated. The driver is also modified to pass the
configure values to registers.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Pin multiplexing is a function of the PORT peripheral. This change
defines a separate pinmux device at the same address as the PORTs
themselves.
Signed-off-by: Michael Hope <mlhx@google.com>
Adds dts nodes and fixups for the fxos8700, fxas21002, and max30101
sensors to the hexiwear_k64 board. Tested with:
- samples/sensor/fxos8700
- samples/sensor/fxas21002
- samples/sensor/max30101
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts nodes and fixups for the fxos8700 sensor to the frdm_kw41z
board. Tested with samples/sensor/fxos8700
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts nodes and fixups for the fxos8700 sensor to the frdm_k64f
board. Tested with samples/sensor/fxos8700
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hts221 sensor driver was implicitly made dependent upon the
disco_l475_iot1 board when it was converted to dts, so build the
associated sample only for this board. This issue was encountered when
adding sensor dts support to nxp boards, which don't have hts221.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We should enable CONFIG_POLL on application level when
we want to use SPI transceive_async() function.
This patch removes it from disco_l475_iot1 default
configuration.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The jlink commander failed to program flash with auto speed on the
usb_kw24d512 board, so set the speed explicitly on this board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that the jlink runner supports the flash command, set
BOARD_FLASH_RUNNER when the OpenSDA or LPCLink debug adapter is
programmed with jlink firmware.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enable and configure I2C1.
This configuration enables ready to use compatibility
with expansion shields based on Arduino type connectors
Additionally, fix comment on clock speed in board _defconfig
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Applies to #4008 and #5159 for this board. Problem is that the
button interrupt callback was only firing once. Solution is to
set the pin pull up flag to GPIO_PUD_PULL_UP.
Signed-off-by: Anders Pitman <tapitman11@gmail.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This moves and merges the existing board-level dts.fixup files
for STM32 L4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
disco_l475_iot1 boards fixup blocks for devices connected via SPI
and I2C stay in board level dts.fixup file, because they are board
specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F3 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F1 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
96b_carbon boards fixup block for Bluetooth HCI device via SPI
stays in board level dts.fixup file, because it is board specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F0 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
When we updated the Nordic SoCs for getting flash controller label/name
from dts, we missed updating the 96b_nitrogen/dts.fixup file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Move bluetooth module SPI port related configuration
to dts and generate dts based defines on 96b_carbon
and disco_l475_iot1.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
references to pdf files (e.g.,
www.st.com/resource/en/reference_manual/dm00091010.pdf)
were missing the http:// prefix so looked like a relative reference.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Adding 'config POLL' in Kconfig.defconfig creates a dependency
between CONFIG_POLL and board BOARD_DISCO_L475_IOT1 & SPI.
Remove this definition from the file and set CONFIG_POLL
in board _defconfig file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In Qemu 2.10 we can run this board configuration in Qemu directly. Make
this possible by setting the board configuration to allow emulation.
Until we have the latest QEMU in the SDK this can be used with a recent
QEMU like this:
$ mkdir build; cd build
$ cmake -DQEMU=/usr/bin/qemu-system-arm -DBOARD=mps2_an385 ..
$ make run
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some boards are supported natively by qemu. This option will allow us to
run tests using those platforms directly without having to go via a
dedicated qemu board definition.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In order to be able to document the build on Windows and UNIX
systems, slight variations are required on the app commands
that are used throughout the documentation system.
This includes getting rid of the prompt symbol and providing commands
for both UNIX and Windows operating systems.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Most boards enable the pinmux by default by setting CONFIG_PINMUX=y in
<board>_defconfig, but several boards did it in Kconfig.defconfig
instead. Several code reviews, such as #5043, have suggested using a
select in Kconfig.board to enable the pinmux, however this caused
warnings:
warning: (BOARD_LPCXPRESSO54114) selects PINMUX which has unmet direct
dependencies (BOARD_FRDM_K64F || BOARD_FRDM_KL25Z || BOARD_FRDM_KW41Z ||
BOARD_HEXIWEAR_K64 || BOARD_USB_KW24D512 || BOARD_GALILEO)
Fix how these boards enable the pinmux so they are more consistent with
other boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Defining TRIGGER_MODE choices in board Kconfig.defconfig files
brings unwanted dependency and warning messages when using sensors
on other boards.
Change sensor configuration by enabling wanted trigger choice rather
than redefining choice.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Updated previously broken links to emulation setup install, instructions
and Getting Started Guide.
Also added a few clarifications for the prerequisites setup.
Fixes#5601
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Instead of accessing the environment variable ZEPHYR_BASE every time we
require accessing the source code root, use an intermediate variable
that has OS path separators correctly set to '/' to avoid issues on
Windows.
Note: This removes the ZEPHYR_SOURCE_DIR CMake variable. External
applications using that will need to change to use the new ZEPHYR_BASE
variable.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Old reference on driver's specific raw mode was still lurking around.
Removing those.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This was validated on the cc3220sf_launchxl board
using the Zephyr thermometer sample program
adapted to call the i2c driver directly, and fetching
samples from the on-board TMP006 temperature sensor.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
ETH_MCUX_0 needs to be turned on when CONFIG_NET_L2_ETHERNET is enabled.
If CONFIG_NET_L2_ETHERNET is disabled (e.g. when configured for 6loble),
then ETH_MCUX_0 should remain disabled.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
This board doesn't support `make flash` way of programming.
So, remove that from documentation.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Of these, only struct net_ipv6_nbr_data::send_ns is a descriptive
change:
send_ns is used for timing Neighbor Solicitations in general, not
just for DAD.
The rest are typo/grammar fixes.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Update board definitions with supported feature. This is temporary
until we have full coverage for device drivers in DTS, then we can use
DTS instead.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use the existing J-Link functionality to support debugging nRF5x targets
with GDB over a Segger J-Link USB connection.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
ST official reference for this board is B-L475E-IOT01A.
While not used in zephyr, add reference in documentaion title.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable DT support in the dfu-util flasher when the target is a
DfuSe (DFU + ST extensions) device.
Untangling DfuSe-specific options (currently, the default is 'leave',
to immediately start running after the flashing is done) from the
actual address makes this cleaner, and sets up a subsequent patch to
let callers set DfuSe options.
It also lets us fix an unnecessary printline when flashing DfuSe
devices. There's no need to reset those, since the 'leave' modifier
starts execution immediately.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The various runners (flash/debug scripts) use environment variables to
take arguments. This is legacy behavior which is not desirable.
Use command line arguments instead.
Note: this leaves more general environment variables with publicly
documented behavior in place for now, for compatibility, e.g.:
ZEPHYR_FLASH_OVER_DFU, OPENSDA_FW, ESP_IDF_PATH, PYOCD_DAPARG
For example, when using dfu-util to flash arduino_101, instead of
setting DFUUTIL_PID, DFUUTIL_ALT, and DFUUTIL_IMG environment
variables, have the script invocation look like this:
python3 .../zephyr_flash_debug.py dfu-util flash \
[common arguments omitted] \
--pid=8087:0aba --alt=x86_app \
--img=.../build/zephyr/zephyr.bin
Make similar changes for other runners (openocd, etc.) and
targets (debug, debugserver).
To implement this in the scripts:
- have the individual scripts/support/runner/some-runner.py files
register their own command line arguments
- teach them to construct instances from arguments, not the
environment
- have zephyr_flash_debug.py request runners to register command
line argument parsers, and handle arguments
In the build system:
- add a new board_runner_args() extension function that board.cmake
files can use to add to the zephyr_flash_debug.py command line
- adjust cmake/flash/CMakeLists.txt to invoke with arguments
- add new helper include files for each runner (like
boards/common/dfu-util.board.cmake, etc.), which add default
options as needed and then add on overrides from
board_runner_args() calls
- update board.cmake files to use the new includes and extension
This implied some tweaking when using openocd to make the CMake string
escaping and unescaping work properly.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The Python-based runners have replaced the old shell scripts. Refactor
the build system accordingly:
- FLASH_SCRIPT is now BOARD_FLASH_RUNNER
- DEBUG_SCRIPT is now BOARD_DEBUG_RUNNER
The values, rather than being the names of files, are now the names of
runners in scripts/support/runner. They are still short, descriptive
names like "openocd", "jlink", "em-starterkit", etc.
Adjust the zephyr_flash_debug.py call and runner internals
accordingly. Have each runner class report a name and the commands it
can handle. This lets us move some boilerplate from each do_run()
method into the common run() routine, and enables further improvements
in future patches.
The handles_command() method is temporary, and will be replaced by a
more general mechanism for describing runner capabilities in a
subsequent patch. The initial use case for extending this is to add
device tree awareness to the runners.
To try to avoid user confusion, abort the configuration if an
xxx_SCRIPT is defined.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
To avoid configuration surprises, replace
CONFIG_CLOCK_STM32_PLL_SRC_HSI
with
CONFIG_CLOCK_STM32_PLL_SRC_HSI=y
No impact today, but could depend on tools.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On stm32f3_disco pins PF0/PF1 are used for OSC_IN/OSC_OUT
signals. Use pins PA9/PA10 for I2C_2 port
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Enable USB OTG support for olimex stm32-e407 and stm32f407g_disc1
boards by adding USB OTG to the pinmux table. Also, fix out of
range endpoint addresses in CDC ACM case for STM32F4 based boards.
Signed-off-by: Sudarsana Nagineni <sudarsana.nagineni@intel.com>
This board doesn't support the 'flash' goal, which was mistakenly
included during the CMake conversion.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
External serial flash on this board is 4MB.
Previously, this was confused with internal flash, which is 1MB.
Fixes#1270
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The following files didn't have any copyright or license headers on them
when they got contributed. So add the SPDX Apache license and
appropriate copyright info:
boards/arm/stm32l476g_disco/pinmux.c
samples/basic/threads/src/main.c
tests/net/socket/tcp/src/main.c
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added Inter-IC Sound driver (based on SSC module) for Atmel
SAM MCU family.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-2509
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The kernel timer frequency was incorrectly set to the system clock
frequency (528 MHz) instead of the core clock frequency (600 MHz).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Not all boards require the various binary formats zephyr generates. So
be selective based on the arch, SoC or board and only geenrate the
binaries actually needed.
Fixes#5009
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add configuration, pinmux, dts and documentation for the STM32L476G
Discovery board based on the STM32L476VG SoC.
Signed-off-by: Arthur SFEZ <arthur.sfez@gmail.com>
The '=' character was incorrectly getting passed to the JLinkGDBServer
device argument, and caused the server to fail to connect to the target.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Rename the Atmel SAM I2C driver based on TWIHS module to match the
convention:
<driver class>_<SoC family>_<hardware module used by the driver>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
olimexino_stm32 was not getting the flash base address from the Kconfig
variable. Since the board uses DTS that will get set, so we can use the
standard openocd.board.cmake.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Unlike other NXP SoCs currently in Zephyr, the mimxrt1052 has the ARM
MPU rather than the NXP MPU. Start out by enabling it with a simple set
of memory regions for "flash" (ITCM), "ram" (DTCM), and the peripheral
buses. More regions will need to be added when we implement support for
external memories.
Tested with:
- samples/mpu/mpu_stack_guard_test
- tests/kernel/mem_protect/protection
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds support for the NXP MIMXRT1050-EVK board, an entry-level
development board for the new mimxrt1052 Cortex-M7 SoC.
Adds pinmuxing, dts, documentation, and jlink debug support for the new
board. Note that pinmuxing uses the mcux pinmux driver directly rather
than the Zephyr pinmux interface. The mimxrt1052 SoC has complicated
pinmuxing that may require changing the Zephyr pinmux interface to
support, so for now let's use the mcux driver directly.
We are also not yet configuring the external flash, therefore a debugger
is required to load code to the internal sram. The on-board OpenSDA
circuit with jlink firmware is sufficient, and the 'make debug' build
target is supported.
Samples tested include: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
the current zephyr sdk now includes openocd configurations for l4
boards, we can now update the boards and docs to reflect this
Signed-off-by: Arthur SFEZ <arthur.sfez@gmail.com>
The old way of constructing FLASH_SCRIPT_ENV_VARS was corrupting the
values that were passed to the flasher. This new method is the
standard way of creating a dictionary/hashmap in CMake and does not
suffer from the same problem.
This fixes
https://github.com/zephyrproject-rtos/zephyr/issues/4844#event-1334599401
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the dts fixup files into the board dir so that board ports can be
more standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Due to copy paste issue, doc file for board nucleo_f030r8
had wrong file name.
Fix it with correct doc name
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
I2C_1 is enabled in board's DT file but we need to enable
it also in boards default config.
I2C_0 doesn't exist in STM32L475 SOC.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Provide default settings in disco_l475_iot board for following
sensors: LSM6DSL, LIS3MDL, LPS22HB, HTS221.
Sensors are disabled by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
