Convert to the new GPIO API using logical access, including setting the
GPIO line as active low in the Device Tree source.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update bluetooth hcp_spi sample to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Introduce define for dt generated gpio flags
- Update 96b_carbon_nrf51.dts according to new bindings
- Gpio IRQ pin is configured to output inactive
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use new configuration API, replace callback enable/disable with
interrupt enable/disable, and set active level in devicetree source.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Conver to the new GPIO API using raw access, since the driver
has its own macros to define signal levels.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert to the new API using raw access, since it's a common access
layer shared by multiple (right now only ublox-sara-r4) modems.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert to the new GPIO API using logical levels, and remove the
duplicate implementation of LED control that existed.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the flags included in the new GPIO API to describe the properties of
LEDs and buttons in the device tree source files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the new API and replace the enable/disable callback calls with pin
interrupt configuration instead.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update devicetree sources and bindings, switch to new GPIO API. Use
devicetree property name to identify interrupt signal.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert to the new API, using raw access since there is no Device-Tree
definitions for this particular sample.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Conver to the new GPIO API, using raw access since there is no DT
definitions for this particular usage of the pins.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update sample overlays. Add GPIO flags to configuration state.
Refactor to split out setup/handle/process phases. Switch to new API
replacing callback dis/enable with interrupt dis/enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the GPIO_ACTIVE_LOW to signal that the button pins are active low,
instead of the deprecated GPIO_INT_ACTIVE_LOW.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Converts the sdhc spi driver to the new gpio api. Updates device trees
for the olimexino_stm32 and nrf52840_blip boards to set appropriate
active high/low polarity for the spi chip select pin.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add the common config structure as a prefix of the driver-specific
config structure. This driver uses fixups to define a common name
based on the SOC series; until aliases for the new properties are
added the code assumes all pins are supported.
Since pin ordinal validation is now done directly in gpio API,
remove checks inside the driver itself.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
