Put together specific for BR/EDR interfaces.
Change-Id: Icfc4d0ebd129b8fcbb547a7f21336cd4c950657c
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Accourding to the spec the IP Support Service shall be instantiated as
a «Primary Service».
Change-Id: Ief0a2729c2752a33c8e7d4d9fae017c22e969e61
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Support for Freescale/NXP K64 SPI modules, limited to:
- Master mode
- A single active set of clock and transfer attributes (CTAR0), which
includes non-adjustable delay parameters
- Tx FIFO fill and Rx FIFO drain interrupt handling
- Standard, continuous select and continuous SCK SPI transfer formats
Also, divide-by-zero code generation in this driver is prevented.
The 'volatile' attribute is added to some of the variables in the baud
rate and delay calculation functions of the K64 SPI driver in order to
prevent bad code generation by gcc toolchains for ARM seen when an
optimization setting above -O0 is used.
Specifically, a register is loaded with the constant 0 and is used as
the divisor in a following divide instruction, resulting in a
divide-by-zero exception.
This issue has been seen with gcc versions 4.8.1 (the VxWorks toolchain)
and 5.2.0 (the Zephyr SDK toolchain).
Change-Id: Ib5b2b748aad8fdfd5e8d40544e6e1abef3713abe
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
Internal K64 SoC clock dividers were hard-coded. They've been replaced
with config options.
Change-Id: I583307f2e3341525f4445e9ceb89d36634b12802
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
PWM support using the Freescale K64 FlexTimer Module (FTM)
Change-Id: Iaad429c01bd877babba04e84d6a4679bd7e38120
Work-by: Mike Hirst <michael.hirst@windriver.com>
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
Phase describes number of clock ticks of delay before the start of the
pulse.
Change-Id: I8e2f5fde423edff09cd5a4a298d911cb7d3cc126
Work-by: Mike Hirst <michael.hirst@windriver.com>
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
Interrupt and callback function support is added to the K64F GPIO driver.
The implementation is based on the Designware GPIO driver (gpio-dw.*).
Change-Id: Id88d06f748400f8f822ca98e098cb44a53678c38
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
K64 pinmux support is created as a normal driver.
As opposed to the Galileo board, the pin configuration options are
defined by the MCU and are not board-specific. Separate
platform/board-specific configuration code uses the pinmux driver for
the default pin settings. For FRDM-K64F, only the Arduino pins (22 of a
possible 160) are set up.
Some of the I/O pins routed to the Arduino header are also configured as
JTAG/SWD signals by default and are used by the OpenSDAv2 debug
interface. Therefore, a PRESERVE_JTAG_IO_PINS config option was created
for the FRDM-K64 platform to prevent the default pin settings from
re-configuring these pins.
The K64 MCU separates pin configuration and control, implemented in the
pinmux driver, from GPIO. This results in some cross referencing
between the K64 GPIO driver and the K64 pinmux driver due to the
dependencies of one on the other.
This pinmux driver also uses the expanded pinmux function/mode parameter
size to describe pin configuration options with bit fields for the K64,
including up to 8 pin functions, plus interrupt, pullup/down, drive
strength, open-drain and slew rate.
The following GCC warnings in the K64 pinmux driver are prevented when not
compiling with 'no-optimization' (-O0):
warning: 'gpio_dev' may be used uninitialized in this function
[-Wmaybe-uninitialized]
Change-Id: Ie5031d18750143bf895883058b3cd55fd9989fd3
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
Reorganizes mostly by using preprocessor (indirectly Kconfig options)
strictly LE-SMP related interfaces and security interfaces shared
between LE and BREDR connections.
Change-Id: I90daa36d72403cd5b73e6791714fcaf7f1fbe8e5
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
This adds support for get supported commands of l2cap service.
Change-Id: Ic3e2b6502c05a5784d1fd01af0e47cce11e6d2c9
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
This patch adds initial declaration of l2cap service in tester
application.
Change-Id: I9bd729bc351b2fe135e7b5b80262b45eaf70b10b
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
Implement GATT read reusing gatt_private to store GATT parameters.
Change-Id: Ie3c58a6272cc7cf380e4d3a04e45b191680d1ebe
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The Read Response only contains a Characteristic Value that is less
than or equal to (ATT_MTU – 1) octets in length. Include also equal.
Change-Id: I139d1460159aafa2187e04cddd8df57d42807c67
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Echo-server and client will exchange data without monitor
tool support.
Change-Id: I3cf73a4baf025bf7e5fc634bef696d5f0e6b4c57
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
There were no spaces around printed IPv6 address which
makes it hard to read.
Change-Id: Ia5f8dad7d21fe8a9a4feb9976b1a90fe624102ab
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The pinmux API was modified to expand the meaning of the 'func' argument
to allow it to represent more than a pre-configured function. This was done
to reasonably accommodate a larger range of pin configuration options
offered by other MCUs, such as the Freescale K64 (up to 8 pin functions,
plus interrupt, pullup/down, drive strength, open-drain, slew rate, etc.).
This allows bit fields to be used to define various settings.
Change-Id: I2b216b822c6bae7133eed01c8c3339bb47b6c5db
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
Basic driver support for the Freescale K64 GPIO module.
Note that only pin direction, read and write are supported.
Change-Id: I6587bb260197a00497be9ac991002e3dde54718d
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
Adds missing '$' to export command, env variable PYTHON_PATH was not being
expanded when using such command.
typo:
Change-Id: Iad7ee60fbe2699cceb6a6ff6cd64e3bc4ebd2f58
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
ipm_send_t properly had 'const void *' for the data payload, but
not the ipm_send() API.
Change-Id: I62a424d37bc17f5bc3646c71d3ff3b029f52cbcc
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Migrated from internal repository.
Run "make flash" for each on the same Arduino 101 device.
Origin: Original code, Zephyr "hello world" used as a starting point
Change-Id: I3fdeed6b7e85ad703983c2674e265c85a365ce5b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This will ensure uniformity in the future, but will require what code is
currently aligned on 4-char tabs to be reformated (basically the kernel
and arch code, and some other) to fit in 80 columns with 8-char tabs.
However, it will be more natural to developers used to 8-char tabs,
i.e. people used to work on Linux and other open source projects, which
is our audience, and will lower the barrier of entry.
Change-Id: I626b20e62ba1a5dddd030a27185f51237e5e98b5
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
In the pinmux_dev driver for the Quark SE development board in
pinmux_dev_set() the variable 'mode' was used, but it should have been
'func'. This was causing a compilation error:
/home/vinicius/work/zephyr/boards/quark_se_devboard/pinmux.c:
In function 'pinmux_dev_set':
/home/vinicius/work/zephyr/boards/quark_se_devboard/pinmux.c:245:23:
error: 'mode' undeclared (first use in this function)
uint32_t mode_mask = mode << (pin_no << 1);
Change-Id: I5b9df7c6b488dc5b8819fcf59bb3b994d9d4820b
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
It is semantically identical to CONFIG_SW_ISR_TABLE.
Change-Id: Iff0c47166ee6fb1fd8a0991a67bc863d45c32559
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This scenario is no longer supported in code; the Kconfig
didn't actually do anything.
Change-Id: Ic48bffb5180c4f72bc9c5d85cf18b1072432b951
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This table was still being added to ROM even if
CONFIG_SW_ISR_TABLE=n.
Change-Id: Ia0de1349960af1c62e88344b3d5b6655b638219b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This config option is no longer implemented and doesn't actually
do anything.
Change-Id: I57ab7ba688f57da21f8a58f62ea37dc6b8daaf18
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We don't support hard-coding vectors in this table anymore.
If someone really wants to do this, they can set
IRQ_VECTOR_TABLE_CUSTOM and define their own.
Change-Id: I45f49782ba5fefb0a02eab02ec96efd0019bc6d5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Fix dependencies for external and sensor clock device names in
clock_control Kconfig.
Change-Id: I708f025cf3ce97bcd003754fb5b395712d203107
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
bt_auth_cancel can be used to cancel any type of pairing.
Change-Id: Ia1a6ba834186ab6d5082d3eb473319c2d70cf4a7
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
This patch extends the uart sample so the same functionality (write
buffer, read char then write buffer again) is implemented using
irq-based APIs.
Change-Id: Iefb14dae2b253f90da64ccef8c123619ed494aca
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch reformats philosophers sample to fit in 80 columns
with 8-char tabs. It also fixes other coding style issues
reported by chechpatch.pl script with -f option.
Change-Id: Ie7ed59db4e67e279a26000247a1838221ac37cd3
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This function doesn't return number of bytes sent but error code.
Change-Id: Ife5e4d3957226ce2b4283b5d229095db2ac375dc
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Rearrange headers so that internal header files gap_internal.h and
gatt_internal.h do not source headers, they are included in *.c files.
Change-Id: I6450ab90eec1b450ee8a138da2ed72b8aaeaf616
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This adds indication support for one characterist of the vendor service
so it can be used to test bt_gatt_indicate API.
Change-Id: Ief058c93caf3e30972eca920c050451f6120543b
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This documents more in detail the behavior of the API, what callbacks are
involved and when they are called, etc.
Change-Id: I62994ed09a9e8b3f14dc3f8c792469a93aeefabc
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Update RPC functions and data types, works with NBLE firmware
niko-0301
Change-Id: I3538fab1d20c6e140d995a797d68486be6cd0f23
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
As per 7.8.12 the check on timeout (time unit ajdusted) must be:
timeout * 10 > (1+latency) (max * 1.25 *2).
Change-Id: I0181b3ab2e1ad38bce9312b6bd83e49082d49024
Signed-off-by: Roger Lendenmann <roger.lendenmann@intel.com>
Making all the files in this section consistent with :dfn: in the intro
paragraph, API headings, present-tense verbs in APIs, parallel wording.
Change-Id: I5259c443076b1ac6602352dab42d35d5aca6e5b5
Signed-off-by: L.S. Cook <leonax.cook@intel.com>
Making all the files in this section consistent with :dfn: in
the intro paragraph, API headings, present-tense verbs in APIs.
Clarified paragraphs on priorty-bazed waiting and priority
inheritance.
Change-Id: I26cc49926bc49c9c68300b6249aeb52c1be33625
Signed-off-by: L.S. Cook <leonax.cook@intel.com>
This patch fixes the RTC_DW configuration option. DesignWare and QMSI
drivers shouldn't have any dependency from each other. All driveris
are following this policy, but the RTC.
Change-Id: Ic6bdef492d26978aa875c54d41ef39d407ddf4e1
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Remove CPU_MIGHT_SUPPORT_CLFLUSH as excessive.
Removal the flag requires adding per-SoC cnfiguration,
as some Quark models support clflush instruction, but
some do not, even on compiler level.
Change-Id: I655cba00c629db55d1813c199a2fe08b2d60ef4f
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Rearrange the source code in order to place functions
depending on clflush support detection into the proper
section.
Removed dependency between CACHE_LINE_SIZE_DETECT and
CLFLUSH_INSTRUCTION_SUPPORTED or CONFIG_CLFLUSH_DETECT.
Change-Id: I62ba5199763ed16c71f1d2fa372f6cc99b303e6a
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Enable support for WinBond W25QXXDV SPI flash on
arduino 101 platform.
Change-Id: Ia4dc73f956f79c6a56a31bc3dfca4e5298447742
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
