Update RPC to Nordic BLE radio module to 0425 revision.
Change-Id: Ieb79821acd5a8fbc4358ea5e1f258834a7932c2c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
On current Curie-based boards UART 0 is wired to the nRF51 BLE
controller and requires HW flow control to be enabled in order to
function. This patch restores the same behavior that was present
before the "qmsi: uart: use built-in qmsi driver" patch.
Change-Id: If7ea347f5ab8b460f39123dcc0d75d711a5a1c2a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
iOS BT stack has a bug in LE SC implementation. If EncKey is not set in
key distribution it sends Pairing Failed PDU if any (?) keys were
distributed. This wasn't visible before as without local privacy no
keys were distributed for LE SC with iPhone.
Change-Id: I36c2398ea821c6048d970b93a58189eb466ea434
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Indenting away the function pointer name from the return type is not
consistent with the rest of the code base.
Change-Id: I8bd69ccfd201fa3c9eedb13caeff920774d1defd
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Set the IPv4 address, netmask and default router addresses
that are used for automatic testing.
Change-Id: Iebddc42c56dceeb089af7878102f8a73c30f0b74
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IPv4 address is set properly for testing purposes.
Change-Id: I996e7435276f65dbb642aa9ab99c37cd842d4b39
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If TCP is activated, then the echo-server application starts
to listen TCP socket and reply data to caller. For TCP
connections, the application data is not reversed because
it would make it difficult to verify the data in the sender
side. The TCP packets might be split into smaller chunks by
echo-client so client would have some unnecessary difficult
to verify the data it sent if we reverse it.
Change-Id: Ic146dfc75825bc8057968c581bfe9d3285e0d7b4
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is not mandatory but makes sure that TX fiber is wakeup
as soon as possible to send the actual IP packet.
Change-Id: I48fb8a5e428f67e249ba0ea2c0f14b0d512f148b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IPv6 header compression is temporarily turned off for TCP
packets because of stack limitations when a packet needs to
be resent.
Change-Id: I572f177c727aa39757afebdc594cc07c8d8a1bd5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Currently we can only be a server that listens TCP data and
can send back data.
Change-Id: If009b7cb608029a8fb3889772fe15e45a154679d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
User can enable TCP server (listening socket) support in the
IP stack. This commit does not yet have TCP client (connecting
socket) support.
Change-Id: I75dd02a81addc1d1e026463b53631d56378157df
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Initial import for some new TCP related files from Contiki.
Fixed the compilation of imported TCP code but actual TCP
support comes in following commits.
Origin: Contiki
Change-Id: I0b42e2fa11de15f9b4da53e369cf114fcfd6cd21
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It allows to silently ignore non-existent files.
When using wildcards in Kconfig source files
(e.g. source folder/*/Kconfig), it is possible to refer files
that does not exist. In the previous example, it is possible
that Kconfig files do not exist in one of the folder's
subfolders and it is not a requirement for the file to exist
in each one of the subfolders.
Additionally, it fixes an issue for wildcards in the file name.
If the name contains a wildcard, Kconfig should iterate
over each file included in the wildcard
(e.g source folder/myKconfig.*)
Jira: ZEP-177
Change-Id: I5aa192ca1e2df83461b12a86fe29a98cd95c4256
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
Adapting CC2520 driver to use the new callback format. That way, cc2520
will work on boards where FIFOP and SFD are hooked to a different GPIO
controller.
Change-Id: Ia40b17867000de26f332f36422f84bb3f20be2aa
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adapting GPIO samples to use the new callback format.
Change-Id: I944dce4faeeee30117edbd7a065e40caa0b7ed66
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adapting GPIO based sensors to use the new callback format.
Change-Id: Ibdc68bf80a2ee42dcaf25c7a6e4431f9b64dc20a
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Many sub-systems might require to set a callback on different pins.
Thus enabling it via changing the API.
It is also possible to retrieve private-data in the callback handler
using CONTAINER_OF() macro (include/misc/util.h).
Former API is still available, and is emulated through the new one.
Using both should not be a problem as it's using new API calls.
However, it's now better to start using the new API.
Change-Id: Id16594202905976cc524775d1cd3592b54a84514
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To show possible usage of the device_busy_xxx() APIs.
Meant to show how drivers and power policy manager can use them.
Change-Id: I49d1dedd9a7b8d6bf09080c6c7243f0666330941
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Certain Low power SOC states (e.g. deep sleep) will result in device
IP blocks losing state. In such a scenario it can be useful to have
a mechanism for devices (driver code) to signal the power manager /
policy that they are in the middle of a transaction.
We expect the device driver code to make a call to
device_busy_set(device *) before initiating a transaction and
device_busy_clear(device *) on completion. It is expected that device
driver developers will add this as necessary in their drivers.
Further an API is provided for power manager application / policy to
check this. Based on this the power manager / policy can decide
whether or not to go into a particular power state.
Change-Id: I0fedd90b98e182cd41b53c7f9e08655532822faa
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
The index.rst file should reference variables only once.
Jira: ZEP-148
Change-Id: Ia5aad1d3ccd0f7c93fca94f1fa0ad88171eaf5c1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
For Quark D2000 we use QMSI drivers, so the initialisation code is no
longer needed.
Change-Id: I22aaa35288e230c455a19b9e67dc6cfb7dc0ff12
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
QMSI defines all the registers of the SoC and other values in
qm_soc_regs.h, so cleanup soc.h and rely on the data from the BSP
contained in qm_soc_regs.h.
Change-Id: I672925cf1c0144a9ed64073ea289c691285a8082
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
For linking with external library, use QMSI_LIBRARY and point
to path of the library using QMSI_INSTALL_PATH
Change-Id: Icd954188a26cc02074aa8fe08a4afdea31879f60
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix naming and use a global driver name for instance.
Change-Id: I30a54cb9c20773e1b6fdc57b934aa564612a6c45
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not depend on specific implementation of the driver, use
well-known driver name used across multiple IPs.
Change-Id: I823fcfa01ce1484dd89f6ade8fbe7017f2084bc6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not have priority per IP, use one config instead.
Change-Id: Ieb2923d4749a294e2a1c677d47d56a14cee3f36d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use same string for driver name used for binding and fix
sample app to work with multiple drivers, not only DW driver.
Change-Id: I4d40aa9d4e83fcf16dc883bb74c3f0e3e30e3502
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Compiling without the drivers prefix causes the following type of
compiler error:
include/uart.h:42:21: fatal error: pci/pci.h: No such file or directory
Change-Id: I99cd814708e74ed4722e5e906819497010263337
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
It was not possible to add directories under an SoC family
because of the direct call to Makefile in the SoC series from the
architecture level.
While we have SoC still using the old structure, add a conditional
to still support old structure and allow Makefiles directly under
an SoC family directory.
This is useful for adding drivers and BSP files common to one family.
Change-Id: I85dc8341523b41949de91d78675153ce0baa5aac
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add API for reading, writing and updating internal registers of I2C
devices. This API is meant to be used as a simpler way of communicating
with I2C devices that have 8-bit internal registers.
Change-Id: I7280eb530039aa10ad9cc19c1c309c7a2f473eb4
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Explanations and guidelines when porting Zephyr to a new processor
architecture or ABI.
Change-Id: Ibb3a26636dca6b248103e4744c333911c2af0e50
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This is more of a convenience to let the driver identify itself in
debug logs and the monitor protocol.
Change-Id: I73351477e98d45d6344c180b8088bde29df6f7d9
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
