Since MSYS2 provides a UNIX-like environment, treating it as a Windows
build caused issues with the paths.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the PHY update complete event can be generated due to the
procedure being initiated by the peer, use a flag to
differentiate between local auto update initiated on connection
complete versus peer initiated anytime in the connection. This
is necessary to avoid repeated initiation of auto-update
procedures intended only to be issued on connection complete.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
MinGW is old and unsupported, and it does not even download properly
these days. Remove the instructions that rely on MinGW since they are
only confusing for people trying to build on Windows.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The STM32L4x SoCs embeds a slightly different embedded flash controller
from the STM32F4x SoCs.
This particular controller has the following properties :
- Up to 2 512KiB banks divided in 2KiB pages
- Flash can be accessed in any sizes
- Flash must be written in 64bit aligned 64bit double-words
The drivers/flash/flash_stm32f4x.c is refactored into a new common
drivers/flash/flash_stm32.c and drivers/flash/flash_stm32l4x.c is
created with the STM32L4x specific functions.
To ease the refactoring and keep common functions, the STM32L4x flash
headers are slightly modified to match the hardware reference naming
and solve compilation issues.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
A typo was present ion the erase and write function were bit were
uncorrectly unset but all other bit except the mask were unset.
The code still worked because the two typos fixed themselves.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Limit visibility of configurable TX pins to SAME70 series only.
Previously visibility of configurable SAME70 TX pins extended
to the full SAM family.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Neither ASF nor CMSIS provide defines that can be processed by
the assembler. Exclude those from soc.h. Before this was done
incorrectly in board.h file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Removed CONFIG_HAS_DTS from the stm32f4_disco_defconfig &
stm32l496g_disco_defconfig files as its automatically selected for all
ARM SoCs at this point.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We now get the baud rate for the serial port from the device tree so we
don't need to be setting it in the defconfig.
The baud rate changed from 38400 to 115200 when we introduced the device
tree for MPS2. The default baud rate was based on matching mbed, but we
use 115200 to match the standard default we have for most boards now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch converts Atmel sam3x MCU series to use register
header files from Atmel Software Framework (ASF) library.
By using ASF different Atmel SAM MCU series can use common
device drivers.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patch adds support for remaining Atmel SAM MCU series,
like sam3x to the common GPIO driver. After this update
full SAM MCU family should be supported by the driver.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit rework stm32f4 series dtsi files hierarchy.
stm32f4.dtsi was used as maximum common set of IP while it should
be considered as the minimum common subset.
Then, following on stm32f4 series hierarchy and inheritance rules,
stm32f4xxx.dtsi files are reworked to include the "parent" soc dtsi
file and then add own IPs to each SoC.
Change-Id: I394278c84a8ea38921f9f143f4fc52ef1c645d05
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In stm32 dtsi linux files, uart generic node name is serial.
Rename uart node names of stm32 dtsi files from uart@ to serial@
Change-Id: Iac5cbf7955f23cee520bc1790b0f324a17bfcf9e
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit fixes uart only nodes situation for stm32 devices.
st,stm32-uart yaml description is added to enable compilation
Change-Id: Iea78693bdfb90fbb09612b75685ed7ca0ccca6d6
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add configuration, dtsi and memory configuration fixup for the
STM32F469XI High Performance SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The chosen property that sets which serial port is being used for the
console device wasn't set. Add the property "zephyr,console" to the
Arduino Due, CC3200-LaunchXL, CC3220SF-LaunchXL, and QEMU Cortex M3
boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that NXP boards support 'make flash' and 'make debug' via pyOCD and
Segger J-Link, update all the NXP board docs accordingly. Adds a new
generalized OpenSDA document so certain details don't have to be
repeated for every OpenSDA board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that we can utilize label in the device tree we can convert to
getting the device name for the Atmel SAM3 UART out of the device
tree instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the TI Stellaris UART out of the device
tree instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the TI CC32xx UART out of the device
tree instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the ARM CMSDK APB UART out of the device
tree instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the NXP Kinetis UART out of the device tree
instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the NRF UART out of the device tree
instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the STM32 UART out of the device tree
instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add optional label property to be generated as part of the UART yaml
spec. This lets us use the label string in a device tree to generate
the device name (for example CONFIG_UART_STM32_PORT_1_NAME).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If the value of the property is a string quote it on output. This lets
us use things like label properties that will have values of strings.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The stm32f4discovery was incorrectly named and should have been
stm32f4_disco. Also added 96b_carbon_nrf51 that was missing from the
list.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add configuration, pinmux, dts and documentation for the STM32L496G
Discovery board based on the STM32L496AG SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Update Cube version for STM32L4XX family
from version: V1.6.0
to version: V1.8.0
Add support for following soc:
stm32l496xx
stm32l4a6xx
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
As we now only support DTS for ARM based SoCs we can remove any
associated !HAS_DTS bits in Kconfig. The Nordic NRF5 serial driver and
the ARM CMSDK APB serial drivers had Kconfig bits related to !HAS_DTS
builds.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since we now select HAS_DTS from the cortex-m Kconfig we don't need it
in 96b_carbon_nrf51_defconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* Change emsk to EM Starter Kit
* Fix some typos
* Add more statement for steps of using EM Starter Kit
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
Due to support updated from 2.2 to 2.3, a debug script is provided
for emsk, so developer can directly debug the zephyr application
using commands such as follows.
+ make BOARD=em_starterkit debug
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
Here are the main changes:
* board: Update EMSK onboard resources such as Button, Switch and LEDs
+ update soc.h for em7d, em9d, em11d
+ update board.h for em_starterkit board
* arc: Add floating point support and code density support
+ add kconfig configuration
+ add compiler options
+ add register definitions, marcos, assembly codes
+ fixes in existing codes and configurations.
* arc: Update detailed board configurations for cores of emsk 2.3
* script: Provide arc_debugger.sh for debugging em_starterkit board
+ make BOARD=em_starterkit debug
This will start openocd server for emsk, and arc gdb will connect
to this debug server, user can run `continue` command if user just
want to run the application, or other commands if debugging needed.
+ make BOARD=em_starterkit debugserver
This will start an openocd debugger server for emsk, and user can
connect to this debugserver using arc gdb and do what they want to.
+ make BOARD=em_starterkit flash
This will download the zephyr application elf file to emsk,
and run it.
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
There is not enough memory to run the HTTP server sample
application in Arduino-101 so remove the config file.
Jira: ZEP-2157
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The address family of the UDP port listener was not set. This
caused weird debug prints in net-shell. Now the listener will
be registering IPv4 any address as it should.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When a connection handler was registered, the checker function
introduced in commit 43b37cef ("Check duplicate UDP/TCP connection
handlers") did not check the address family (IPv4 or IPv6) of
the local end point properly. This caused duplicate connection
error to be returned to the caller.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
