Make sure also to increase in_event if only inserting event info was
properly done.
Raising also range limit in Kconfig to a much higher value.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Warnings from Kconfiglib itself always give symbol locations, but the
custom value mismatch warning in kconfig.py doesn't. Make it print the
symbol location(s) too. This is helpful when debugging.
Before:
warning: UART_QMSI_0_HW_FC was assigned the value "y" but got the
value "n" -- check dependencies
After:
warning: UART_QMSI_0_HW_FC (defined at
.../drivers/serial/Kconfig.qmsi:35,
.../arch/x86/soc/intel_quark/quark_se/Kconfig.defconfig.series:194)
was assigned the value "y" but got the value "n" -- check
dependencies
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Cleaned up the use of conditional statements to use the max macro.
Fixes#6230.
Signed-off-by: David Maitland <hello@davidmaitland.me>
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Since commit a792a3d410, adding an ini
file in scripts/sanity_chk/arches/ to support a new board is no longer
needed.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Use the Zephyr toolchain and architecture defined popcount
and first_lsb_set functions instead of GCC specific
functions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix the permitted range of IRQ priority to, 0 to 2, as
maximum one priority level is used, for zero latency IRQs
in nRF51, being an ARM Cortex-M0.
Update the Kconfig default GPIOTE IRQ priority level to the
lowest, for nRF51 a level of 2; for nRF52, a level of 5.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
As per the Apache v2 License, state changes made to the original code in
the modified version of the files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The following test cases have been added for semaphore.
1. Test simple semaphore give/take from an isr.
2. Test simple semaphore give/take from a task.
3. Test semaphore take with no wait.
4. Test semaphore take with no wait and fails.
5. Test semaphore take with timeout and fails.
6. Test semaphore take with timeout.
7. Test semaphore take with timeout as forever
8. Test semaphore take with timeout from an isr.
9. Test semaphore take on multiple threads.
10. Test semaphore give/take from an isr.
11. Test semaphore multiple threads wait on a semaphore.
12. Test semaphore measure timeouts.
13. Test semaphore measure timeout when give is from another thread.
14. Test semaphore multiple sem take and timeouts.
15. Test semaphore multiple sem take with diff timeout & semaphore.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
This test validates random number generator APIs that
is not related to kernel and should not be part of
kernel tests.
Signed-off-by: Praful Swarnakar <praful.swarnakar@intel.com>
If the value argument to set_ifndef() may be unset, the entire value
must be double-quoted to avoid a CMake syntax error.
Fix call sites which don't handle this, or which otherwise make
non-idiomatic use of this function.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Since base64 is such a simple and commonly used feature it makes no
sense to build the whole of mbedTLS for it. Instead take the
implementation that comes with mbedTLS and import it as a native library
outside of ext/ for all to use directly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add support for getting some basic params from the DTS for the UART.
The ns16550 driver still needs to be updated to get IRQ and address
info from DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all ARC SoCs we can remove code associated with !HAS_DTS and
select HAS_DTS at the architecture level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add initial device tree support for the em{7,9,11}d SoC and associated
em_starterkit boards. The device tree at this point specifies cpu core,
memory, interrupt controller, uart's and i2c controllers.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Test that if the checksum offloading is enabled, then we do not
calculate the checksum. Also the normal case, where offloading is
disabled and we need to calculate the checksum, is tested.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create infrastructure that allows ethernet device driver to tell
if it supports network packet checksum offloading. This applies only
to IPv4, UDP or TCP checksums. The driver can enable/disable checksum
offloading separately for Tx and Rx network packets.
If the device (ethernet in this case) can calculate the network
packet checksum for IPv4, UDP or TCP, then do not calculate the
corresponding checksum by the stack itself.
Fixes#2987
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Now that dts i2 qmsi ss nodes generate the right options, let's use
them. Apply the relevant fixup on the targeted SoC.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will generate the necessary configuration for the i2c controller
on quark_d2000.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will generate the necessary configuration for the 2 i2c controllers
on quark_se_c1000.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Applying the change to relevant arch/boards, either in their Kconfig or
the dts specific files.
Taking the opportunity in dw driver to rename the variable the same way
as they are everywhere else in the code (s/dev/dw and s/port/dev) in
init function.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will generate the necessary configuration for the i2c controller on
quark_x1000.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will generate the necessary configuration for the 2 i2c controllers
on quark_se_c1000_ss.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Move driver specific to dedicated file when relevant (i.e.: more than
1-2 options), use if/endif also.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The result of left shifting a bit into the sign-bit is undefined
behavior. This makes the offending shift operation unsigned.
Signed-off-by: Kristian Klomsten Skordal <kristian.skordal@nordicsemi.no>
The test validates the behavior of calling k_thread_start()
of thread which is already started. The thread has to start
execution only when its state is _THREAD_PRESTART.
Signed-off-by: Spoorthi K <spoorthi.k@intel.com>
Each USB sample, when compiled, will provide a different
USB product string. A "nice to have" feature when trying
out the USB samples (they will show up differently in
`lsusb` or `dmesg`), and also illustrates how to set up
custom USB constants in the config files.
Requires #6589.
Signed-off-by: Iván Sánchez Ortega <ivan@sanchezortega.es>
The SAM0 SoC was switched to use DTS for SPI configuration. Update
documentation for the SAM0 based boards to use the correct SPI
controller device names.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
