QMSI is not updated to latest SPI API. Switching to native DW driver,
until we find a way either to update the shim drivers in a
non-performant way, or updating QMSI itself enabling support for
scatter-gather type of buffers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As for RX only, computing the NDF will be used for EEPROM mode.
Only a way to determine EEPROM mode is missing.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It was much more limited than the spi_loopback test, and of course using
the legacy API. Removing it then.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Let's use the new SPI API and ditch the old one.
Signed-off-by: Matthias Boesl <matthias.boesl@gmail.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some device may need to be put up on CS high logic. The active low logic
is the default as usual, but it is now possible to request the active
high logic.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adding Kconfig options to set supported modes by the controller
(master, slave or both)
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
No need to support legacy API there.
The special usage of CS in BlueNRG is centralized it dedicated functions
to avoid all the #ifdefs everywher.
Also managing transaction error.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
EEPROM mode can be, in fact, asserted from tx_bufs/rx_bufs thus removing
it.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of using CONFIG_POLL, which is not directly related to SPI and
is a kernel option, let's have SPI_ASYNC instead. When enabled, it will
select POLL automatically.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
tx_bufs/tx_count and rx_bufs/rx_count can be hold in another dedicated
structure, thus reducing the number of parameters to transceive. This
permits to avoid using the stack when calling transceive.
Since we saved parameters, we can expose back the struct device pointer,
to stay consistent with other device driver APIs.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As the content of this struct will not be modified by drivers, it's
better to pass it as constant. Also, if someday struct device can be
made contant too, this change will make spi ready for registering the
spi_config into ROM directly.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Split QMSI relevant part into its own file. Some config where using
prompt, some not: normalizing it by removing the prompt keyword where
relevant.
Reducing the file by using if/endif when relevant.
However, it still not fully clean default: cfg and default baudrate
should disappear. There is no default configuration to apply as long
as the controller is not configured to run from any part using spi API.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
To try and improve CI builds related to pull requests lets bump up the
number of build slaves to 5 to increase throughput.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some device include a temperature sensor, usually used as a
companion for helping in drift compensation, that measure the
die temperature. This temperature IS NOT related to the the
ambient temperature, hence a clean separation between the two
is required.
This commit introduces a clean separation between the two
types of temperature leaving the old deprecated definition
still there.
The list of current drivers that read the die (and not the ambient)
temperature is the following:
- adxl362
- bma280
- bmg160
- bmi160
- fxos8700
- lis3mdl
- lsm6ds0
- lsm6dsl
- lsm9ds0
- mpu6050
Signed-off-by: Armando Visconti <armando.visconti@st.com>
As the native_posix board has ethernet driver, then enable it by
default if networking is enabled in prj.conf file. This way we can
use generic networking config file when running the application
for native_posix board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the priority currently fits u8_t then use it instead of int
for priority value for queue and thread.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The array size checks were incorrect.
Coverity-CID: 183482
Coverity-CID: 183485
Fixes#6883Fixes#6885
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add SPI bus support to LSM6DSL sensor. The bus routines (i.e. I2C
and SPI) are defined in separate files, where proper r/w callbacks
are registered.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add multifunction composite test for building USB device with HID and
MSC functions.
Fixes: #2613
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The current problem with HID is that we need to "patch" static
descriptor table with the size of report descriptor defined in the
user application.
The proposed solution is to have composite_pre_init() defined with
priority CONFIG_KERNEL_INIT_PRIORITY_DEVICE which should run before
composite_init() defined with priority
CONFIG_APPLICATION_INIT_PRIORITY.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
We can use default values of CONFIG_USB_DEVICE_VID and
CONFIG_USB_DEVICE_PID for sanity check builds.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Added posix_checks, which checks supported priorities,
clocks and timer APIs, mainly in the point of negative
tests to increase code coverage.
Signed-off-by: Niranjhana N <niranjhana.n@intel.com>
In some cases pthread attrib initialization may fail as
garbare value may indicate that this attribute is already
initialized. Destroy the attr object and recreate it.
Signed-off-by: Niranjhana N <niranjhana.n@intel.com>
When randomizing the stack pointer on thread creation
(CONFIG_STACK_POINTER_RANDOM), the fuzz amount might exceed the stack
size, causing an underflow.
Ensure that this will never underflow by only adjusting the stack size
if there's enough space.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
For posix layer implementation of message queue, we need to fetch
basic attributes of message queue. Currently this routine is not
present in Zephyr. So adding this routing into message queue.
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
