Fix the advertise command not setting the peer address parameter to
NULL, this could turn it into a directed advertiser.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
We don't need to define DT_NUM_IRQ_PRIO_BITS or DT_NUM_MPU_REGIONS in
dts_fixup.h files anymore, so we can remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To remove the need to have DT_NUM_IRQ_PRIO_BITS defined in every
dts_fixup.h we can just handle the few variant cases in irq.h. This
allows us to remove DT_NUM_MPU_REGIONS from all the dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To remove the need to have DT_NUM_MPU_REGIONS defined in every
dts_fixup.h we can just handle the few variant cases in arm_mpu.c
directly. This allows us to remove DT_NUM_MPU_REGIONS from all the
dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The documentation references now out-dated links to websites for
board landing page, and firmware download and instructions. This
commit updates the links and adds a link to the latest firmware
development for reference.
Fixes#24325
Signed-off-by: Jennifer Williams <jennifer.m.williams@intel.com>
Fix thread fault, on user mode, when reading variable rt_clock_base.
For the moment, clock_settime is left without system call:
we don't want to expose clock_settime without figuring out access
control
Signed-off-by: Julien D'Ascenzio <julien.dascenzio@paratronic.fr>
The UART driver for samd0 was is missing the .configure and
.config_get functionality expected from api for serial driver.
This commit fixes this by providing basic configuration
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
Some other part of Zephyr has similar defines (SRC)
causing build failures.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This commit enables the GMAC Ethernet support for the `atsame54_xpro`
board which includes an on-board RMII PHY.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds a reference to the SAM E54 maximum queue count value
in the device tree for specifying the range of `ETH_SAM_GMAC_QUEUES`
configuration.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds more pin function definitions (PINMUX_FUNC_I through
PINMUX_FUNC_P) to the pinmux interface header.
The SAM D5x and E5x series devices, for instances, define up to the
"function N" and this change is necessary to support such devices.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the GMAC driver support for the Ethernet-capable SAM0
family devices (SAM E53 and E54 at this time).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the MCLK clock configuration symbol fix-up for the
GMAC peripheral.
The APB-agnostic clock configuration fix-up symbols map to the
SoC-specific APB, in order to accommodate different SoC variants with
the GMAC on different APBs.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds a GMAC instance to the SAM E5x device tree, along with
the refactoring necessary to specify the SAM E5x-specific components.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
In order to use its serial peripheral SERCOMs SAMD socs require their
pins to be configured with pinmux. Currently pins are muxed only for the
boards' default serial interfaces. The pinmux code is written to throw
a compiler error if a user tries to use any sercom in a way it wasn't
pre-defined to be used.
This commit changes compiler errors to warnings so that user can provide
custom pinmuxing code in their app.
Fixes#23133
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
The TCP flag was conflicting with PPP flag in the same union.
This prevented TCP from working properly with PPP.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
New function allows to set from the code the root command. It is
an equivalent of calling 'select <rootcmd>' except it sets command
for all shell instances.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Assigning the allocated IPv4 endpoint as struct sockaddr
leads to the memory overwrite, assign the correct structure,
i.e. struct sockaddr_in.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Some sensor drivers modify there struct's based on DT defines. In those
cases we need to make sure that DT_DRV_COMPAT is set on all the source
files associated with that driver. This updates any such files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The commit fixes problem with test attempting to perform 1 byte writes
to flash, which are not emulated by default.
GH issue: #24207
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
define the irq handler in case of DMA V1 or V2,
for the stm32x soc series
with DMA V1 raise Fifo Error if enabled
with V2, handle the Global Interrupt
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Return an error if the direction of the channel is wrong
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move tables declaration as they are only used locally for now
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Control values when configuring the dma channel
According to the soc specification,
the dma V2 channel counts from 1.
the dma V1 stream counts from 0.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This defines the configuration for the DMA client
as specifed in the ./dts/bindings/dma/st,stm32-dma.yaml
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This sample now supports SMP UDP transport.
Two config overlays have been added for ipv4 and ipv6, respectively.
The sample documentation has been completely revamped to be less
bluetooth focused and more general.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
To prepare this sample supporting future SMP transports, the sample
code is now split into a main and bluetooth file. A common config
has been identified and application specific config is put into
overlay config files.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
This is needed if muxing is enabled in which case we must
change the UART to muxing UART after the AT+CMUX command
has succeed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of global workqueue, use own one so that the users of this
driver can more conveniently use global one. This means GSM modem
can work better with the UART muxing driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of using physical UART to connection to the modem, use
the GSM 07.10 muxing protocol and UART mux driver to create
virtual channels to the modem. This will allow simultaneous
PPP, AT and other type connections to the modem.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
By default PPP interface is not taken up automatically but only
after the PPP connection to modem is ready.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
