west will now be installed via pip in order for the bootstrapper to be
decoupled from the west runners.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The SAM E70 GMAC ethernet driver reference a packet with net_pkt_ref()
when queueing a packet, and unreference it with net_pkt_unref() in the
ISR when it has been fully sent.
The call to net_pkt_ref() is done just after re-enabling the
interruptions, so there is however a small race condition that might
cause the packet to be unreference before being referenced. This is
only theoretical and has not been seen in practice.
Fix that by moving the call to net_pkt_ref() just before re-enabling
the interruptions.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The previous commit replaced the net_pkt element ref with an element
atomic_ref. CI tests turned up more places where ref was used directly.
This commit converts them to use the new element.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
It has been observed that some network drivers, f.ex. the SAM E70 GMAC,
call net_pkt_unref from inside the interrupt that signals the successful
transmission of a packet. This conflicts with the net_pkt_unref call
made by ethernet_send after the packet has been given to the driver.
We fix this by using an atomic_t to hold the reference count as there
might be other, difficult to find cases of net_pkt_(un)ref being used
across threads and interrupts.
The name of the element has been changed from "ref" to "atomic_ref" to
cause a compile error when code still has not been converted to use the
atomic_* functions.
Fixes#12708
Signed-off-by: Daniel Glöckner <dg@emlix.com>
The implementation code itself should not rely on plain POSIX names
and use zsock_ and ZSOCK_ prefixed versions of symbols.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
For some reason, there was sequence like:
1. Get size of RX packet.
2. Allocate pkt buffer.
3. Check if the size of RX packet is too large, then deallocate pkt
buffer and error out.
Instead, reorder operations to check size before allocating buf.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Mark automatically and statically configured mesh-local addresses
with mesh_local flag, so that they are not used as a source for
off-mesh destinations.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This commit introduces a concept of mesh-local IPv6 addresses. Such
addresses should only be used for mesh-local communication, therefore
should not be used to communicate with different subnets (i. e.
destinations outside the mesh).
As `addr_type` field already holds different kind of information
(whether address was created automatically/manually) it was not used in
this case.
Instead a mesh_local flag was added, so that we do not lose information
on how address was created. Address with such flag set will only be
selected as a source address automatically if the destination address
is within the same subnet it belongs to.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
From the documentation of the SoC and the DevKit it turns out that
there's no hardware PWM controller.
Signed-off-by: Francesco Franchina <cescus92@gmail.com>
Adds a new config HAS_MCUX_ENET to constrain which socs can enable the
mcux ethernet driver. This will prevent users from enabling the driver
on socs like kl25z or kw41z which do not have ethernet mac hardware.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The gperf hash table 'kobject_hash.c' is always compiled as -Os to
resolve bug #5226, the same bug also affects the gperf hash table
'priv_stacks_hash.c'.
In this patch we copy over the fix from 'kobject_hash.c' to also fix
'priv_stacks_hash.c'.
See #5672 for more discussion on the original fix.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
We have now two code samples available for ArgonKey board:
1. sensors sample, fetching data from accel/gyro/mag,
barometer, humidity and proximity sensors
2. microphone sample, acquiring 5s audio @16KHz from the
on-board microphone.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit introduces the possibility to have multiple
device nodes attached to the same I2S controller. For this
purpose a new i2s-device.yaml description has been introduced
with the a 'reg' property to define the logic number of the
device. For example, if two microphones are attached to the
same I2S port (say 1) to achieve stereo audio, the two microphones
might be described in dts as:
&i2s1 {
status = "ok";
mic@0 {
compatible = "...";
reg = <0>;
label = "...";
};
mic@1 {
compatible = "...";
reg = <1>;
label = "...";
};
};
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This driver supports ST Microelectronics digital pdm microphones
(MPxxDTyy) connected through different peripherals. Currently only
I2S is supported.
The driver makes use internally of the OpenPDM2PCM library
to convert the PDM audio stream to PCM. Currently the
oversampling factor is fixed to 64.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This library, written by STMicroelectronics, is used to convert an
audio stream from PDM format to PCM format through a signal filtering
and decimation.
Library is located in ext/hal/st/lib/audio.
Origin: ST Microelectronics
License: Apache 2.0
URL: https://os.mbed.com/
Commit: 25:f2c04f757003
Purpose: reconstruct the audio signal produced by ST MEMS microphone
Maintained-by: External
Signed-off-by: Armando Visconti <armando.visconti@st.com>
A recent change in how the fixup mechanism works caused several
regressions. See
https://github.com/zephyrproject-rtos/zephyr/pull/12680 for more
details about the regressions.
The core of the matter is that using defines to pass on include paths
causes interopability issues when integrating with external build
systems.
To resolve this we re-write the fixup mechanism to instead generate an
aggregated fixup file that is ready to be included at build time. Then
no paths are passed through defines and we resolve the regressions
reported.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Fix the following dtc warnings on S1000:
Warning (simple_bus_reg): /soc/pinmux@81C30: simple-bus unit
address format error, expected "81c30"
Warning (alias_paths): /aliases: aliases property name must
include only lowercase and '-'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use auto-generated device tree macros in LIS3MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS2MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DSL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Added UART4 alternate pin function for L4 µC for PC10 and PC11.
Corrected naming of previously defined UART4 TX and RX defines.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Adding a binding .yaml file for Nordic FICR and the
corresponding macro definition for NRF_FICR in
nrfx_config_nrf9160.h header file.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Updated the GCOV_COUNTERS value, without which the coverage data
was corrupted when gcc 8.2 was used.
GH-12571
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Convert the remaining places of the host stack where
net_buf_pull_mem() makes more sense than net_buf_pull().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Take advantage of the new net_buf_pull_mem() API, and refactor the
events from long switch statements into (const) handler tables. This
helps reduce code size and makes it cheap to add proper checks/asserts
for having sufficient data in the buffers coming from the controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's more natural to use net_buf_pull_mem() for the HCI command
parsing. Note that this also fixes a bug in hci_cmd_handle() where it
would previously check for sufficient parameter length with the
command header still included in the buffer (which it shouldn't have
been).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is the same as net_buf_pull(), except that instead of returning
the new buf->data it returns the old buf->data. This was recently
discussed in github issue #12562.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Correct the names of the binding files, so they comply
with binding file naming nomenclature.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes a binding .yaml file for Nordic nRF
SPU peripheral and defines the macro for the peripheral base
register address in file ext/hal/nordic/nrfx_config_nrf9160.h.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The app is already sending period heart beat messages, and since it is
not designed to be used for such long times that would require IVI
Update, keep the secure network beacon sending disabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Suspend the mesh network after 30 minutes of inactivity. This should
help prolong the battery life of boards used at multi-day events, if
the user forgets to power off the device for the night.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Sending a model publication message could fail e.g. if there are no
buffers available, however this doesn't mean that we should stop doing
periodic publishing indefinitely. When an error occurs, make sure to
call the publish_sent() function so that the periodic publishing timer
gets resubmitted if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some cases the Friendship & Low Power Node features aren't
available or feasible, however power saving is nevertheless required.
This patch introduces two new APIs to suspend and resume the Mesh
network. Currently, what this impacts is the LE scanning, the
ability to allocate new outgoing buffers, as well as the model
publishing, beacon and heartbeat timers.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tracking of the BT_MESH_VALID flag and the PB-GATT state was rather
fragile. Add proper error returns to the various GATT service enable &
disable handlers, and toggle the BT_MESH_VALID flag in a single file
(main.c). Use the newly added error returns to ensure that we don't
re-enable PB-GATT if it wasn't already enabled from before.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There's already a flags member in the bt_mesh context, so take
advantage of that for any boolean members that have so far been
bit-fields. This should produce more efficient code, also for the
sequence number that's now its own u32_t.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Docs in the samples folder are a mixture of samples and sample indexes
of more samples, cluttering the index display. This change eliminates
the clutter, be we should reorganize the sample docs so we have a
consistent doc hierarchy (and improved organization).
Fixes: #12758
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add missing -lgcc when compiling with ZEPHYR_TOOLCHAIN_VARIANT=host
merely copying some existing code from
'compiler/{clang,gcc}/target.cmake'.
This fixes compilation for the following boards with an x86
microprocessor:
galileo, minnowboard, qemu_x86, qemu_x86_nommu, up_squared,
up_squared_sbl
Compilation of the following boards with an X86_IAMCU microcontroller
still fail with a "cannot find -lgcc" error:
arduino_101, qemu_x86_iamcu, quark_d2000_crb, quark_se_c1000_devboard,
tinytile
This is _not_ a regression because these boards _already_ failed with
"undefined reference to __udivdi3" and other libgcc symbols.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
