Excerpt from the manual:
If ptr is NULL, then the call is equivalent to malloc(size) [...]
Without this commit, such calls end with a BUS FAULT.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Make sure that when e.g. CONFIG_SERIAL is set, CONFIG_UART_SAM0 is
selected automatically when the sam0 SoC family is used.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Add USART1 and LPUART1 nodes on stm32wb series.
Only these 2 ones are available for now on this series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add GPIO support to stm32wb series.
Only ABCDE and H ports are available for now on this series.
Accordingly, update series dtsi file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support to stm32wb series in stm32 clock_control driver.
Ip is similar to stm32l4 one but AHB bus presacler is renamed
to "CPU1" and CPU2 and AHB4 prescalers should be defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of STM32Cube for STM32WB, update stm32cube
folder to enable build of STM32WB Cube package.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This adds the HAL code needed for the SoC for the stm32wb series.
Origin: ST Microelectronics
License: BSD-3-Clause
URL: http://www.st.com/en/embedded-software/stm32cubewb.html
Commit: 1.0.0
Purpose: HAL layer for stm32wb
Maintained-by: External
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In this commit, a config.h header file is added to support the case
when the NET_CONFIG_SETTINGS is not used. main.c is also modified to
enable platforms that do not support IPv6. These changes are necessary
in order to allow cc3220sf_launchxl support.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Added bBreak, bRingSignal, bFraming, bParity and bOverRun
handling in cdc_acm_line_ctrl_set.
Reference: Chapter 6.5.4 of Universal Serial Bus Communications Class
Subclass Specification for PSTN Devices rev 1.2
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
The CONFIG_ prefix is reserved in Zephyr, rename CONFIG_SHIFT and
associated constants by adding a RCC_ prefix
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Add configuration, pinmux, dts and documentation for the STM32MP157
Discovery board based on the STM32MP157 SoC.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
The stm32mp1 exti ll driver is mandatory for compilation.
add it on top of stm32cubeMP1 version 1.0.0.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Provide required changes to stm32cube HAL and LL for the
STM32MP1X series MCU.
Origin: ST Microelectronics
License: BSD-3-Clause
URL: https://github.com/STMicroelectronics/STM32CubeMP1
Commit: 1.1.0
Purpose: HAL layer for STM32MP1
Maintained-by: External
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Add the initial SoC support for the STM32MP1 family. The code was
tested on STM32MP157c, but should work on any STM32MP1XX currently
available.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
The comment for:
set_target_properties(${logical_target_for_zephyr_elf} PROPERTIES
OUTPUT_NAME ${KERNEL_NAME})
was completely off-topic and making something relatively simple
incredibly puzzling and time-consuming to understand.
Re-order the if(GKSF OR GKOF) clauses so the two initializations of
logical_target_for_zephyr_elf are close to each other and so the very
short clause is not buried at the bottom of the long one.
Other minor logical_target_for_zephyr_elf comment fixes.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Sample code for AMS (Austria Micro Systems) ENS210 temperature and
relative humidity sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Implementation of AMS (Austria Micro Systems) ENS210 temperature and
relative humidity sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Sample code for AMS (Austria Micro Systems) Indoor Air Quality Sensor
reading VOC and equivalent CO2 values.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Mark the three distinct choices for how to program the board as
separate options, and add some clarifications on each. For the MCUboot
route, use smp_svr instead of blinky, to give the user a hint about
how to keep their devices up to date from application land.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
This patch adds support to the nRF9160 for using a dedicated
GPIO pin to reset controllers running on nrf52840_pca10090.
It resets the controller before opening the H4 device, and it
delays the controller from booting until all bytes traveling
to the host have been received and drained from the UART,
thus ensuring that communication can begin from a clean state.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to generalize the currently specialized nRF51 IC setup hook,
make the following changes:
- Generalize the hook to bt_ic_setup()
- Use a weak NOP version by default
- Move the currently existing one to the board folder
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Enable the GPIO reset pin feature of nrf52840_pca10090
on pin P1.02 and the wait NOP feature of the controller.
These are used to let nrf9160_pca10090 synchronize the
HCI communication with nrf52840_pca10090 controllers.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Let one of the MCU interface pins be configured to act
as a reset line. This mitigates the lack of a connection
between the nRF9160 and nRF52840 PINRESET.
Minor refactoring and updated comments.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The patch provides flash offsets appropriate for running
this sample on nrf9160_pac10090 targets.
As that sample is small one, it is done with assumption that image_1
flash partition is empty.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Write protection was not disabled prior erase call.
It used to work before only because nrf driver had not check
the protection before erase execution. This behavior was changed in
order to align to zephyr - which implied requirement for this test fix.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
nRF9160 can't provide FICR data while operation in non-secure
domain.
This patch start using flash layout properties provides by
nrfx API for get flash properties, which resolves problem
described above.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Introduce nrfx_nvmc driver into nordic flash driver implementation.
Thanks to that nrf9160 SoC becomes supported by the driver.
nrfx helps dealing with differences with interface to the NVMC
in secure and non-secure execution modes.
This patch adds NRFX_NVMC Kconfig entry for enabling nrfx_nvmc and
select it along with nordic flash driver.
Disabled UICR operation on nRF9160 for non-secure build
as UICR is not available in this mode.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add driver support for Atmel SAM0 device ID, which is 16-bytes long.
The device ID can simply be read from memory at a known location, but
the location is only described in the data sheet, not in ASF.
For SAMD2x it's 0x0080A00C, 0x0080A040, 0x0080A044 & 0x0080A048.
For SAMD5x it's 0x008061FC, 0x00806010, 0x00806014 & 0x00806018.
This adds a new property to the device tree to define the device ID
registers for this SoC family.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
