Adds a new argument to the openocd runner to optionally specify the
config file. Updates the rv32m1_vega board to use different openocd
config files for the ri5cy and zero-riscy cores.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Introduces a new rv32m1_vega board configuration for the zero-riscy
core. It assumes that the soc has been reconfigured with openocd to boot
to the zero-riscy core instead of the ri5cy core.
Refactors the board-level device tree so the ri5cy and zero-riscy
configurations share common definitions for the led, button, and sensor
nodes.
Tested with:
- samples/hello_world
- samples/synchronization
- samples/basic/blinky
- samples/basic/button
- samples/sensor/fxos8700
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors peripheral addresses, clocks, and compatibles from the ri5cy
core dtsi into a common soc dtsi, then attaches interrupts in
core-specific dtsi files.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The zero-riscy core on the rv32m1 soc does not implement hardware loop
extensions and thus should not enable RISCV_SOC_CONTEXT_SAVE, however it
does still need access to the EVENTx_INTPTPENDCLEAR symbol which comes
from GEN_SOC_OFFSET_SYMS().
Split out the soc offset symbols into a separate config so we can enable
them without enabling soc context saving.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Both the ri5cy and zero-riscy cores in the rv32m1 soc use the same
source clock, so we don't need to conditionalize
SYS_CLOCK_HW_CYCLES_PER_SEC on the ri5cy core.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
CI always runs after new PRs are merged into master. Report failures to
mailing list to get more attention if master fails to build.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Due to a protracted merge of:
5e38ed9320
the naming for the HAL_SW_SWITCH_RADIO_ENABLE_S2_PPI changed
semnatics, now requiring use of
HAL_SW_SWITCH_RADIO_ENABLE_S2_PPI_BASE.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement OpenThreads frame pending bit management on top of the Zephyrs
radio driver API. This allows for proper Sleepy End Devices handling
from the parent side.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Implement newly introduced `configure` API for nRF 802154 radio driver.
Increase maximum number of slots for Frame Pending bit information in
the radio driver.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
License link provided in stm32cube abstract packages was not
reflecting the actual license in use for these packages.
Update the link to BSD 3-Clause official.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The stm32_min_dev board blue/black variant support USB device,
but the usb node removed by merge PR #15245, so add it back.
Signed-off-by: Harry Jiang <explora26@gmail.com>
Remove deprecated headers:
- crc8.h
- crc16.h
- crc32.h
We now have one header only serving crc:
- crc.h
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Mark the PPI channels and groups used by the Bluetooth controller
as occupied and thus unavailable for allocation through nrfx_ppi.
Add also a build time assertion that checks if these PPI channels
do not overlap with those assigned to the pwm_nrf5_sw driver
(to replace the comments in this driver that were supposed to warn
about this threat but had in fact little chance to be read by users).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Mark the PPI channels used by the pwm_nrf5_sw driver as occupied
and thus unavailable for allocation through nrfx_ppi.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Updated the controller implementation to not feature
exchange if already done once either by local or remote peer
device in an active connection session.
Signed-off-by: Alexander Svensen <alsv@nordicsemi.no>
Disable the unsupported controller privacy feature in the
ULL/LLL split architecture implementation.
This feature will be enabled in the future when it has been
ported to support multiple vendor SoCs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Enable the support for Zephyr HCI Vendor-Specific Commands
and Event in the ULL/LLL split architecture implementation
of the controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix incorrectly defined Rx and Tx buffer sizes. Wrong
calculation allocated more memory than necessary.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix Kconfig default values for ULL and LLL execution
priorities that caused build warnings when ranges changes
based on other priority values being selected.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix incorrect data type used in calculation of slot_us
detected by compiler, and reported as possible integer
overflow.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix incorrect conditional compilation that caused compile
error when lll_scan structure did not contain connection
context included which is needed only for central role.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Return -EAGAIN on k_sem_take() failure to take write lock, the error
code is similar to nrfx write_in_progress flag.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Adds required Kconfig options for flash driver.
Adds FatFS filesystem for flash disk.
Fixes#14459.
Note: As USB MSC does not support multiple disks (see #14937),
only one (flash by default, modify CONFIG_MASS_STORAGE_DISK_NAME
to "RAM" for RAM disk) will appear to host.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
The UARTs are on the SoC, not the board, so move their descriptors
to the SoC-level. Also turn on auto IRQ detection as these are PCI-
attached and their IRQs are subject to change depending upon firmware
settings.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
If a UART is configured with IRQ == PCIE_IRQ_DETECT, then use the
pcie_wired_irq() to determine the IRQ at runtime, and install the
handler using the dynamic interrupt mechanism.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The per-UART configuration is boilerplate that is becoming a maintenance
nightmare as it grows. A template file is created, and instances are
created as needed by cmake at build time.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Firmware is supposed to set a register in PCI configuration space which
indicates the hardware IRQ that the endpoint is attached to.
A function is implemented which reads this register, and the PCIe shell
is updated to use it instead of doing it "manually".
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
I'm the de-facto maintainer of all things Apollo Lake these days,
and the Apollo Lake begins with the up_squared.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Notably fix the wrong comment I added in commit 6f011c95c4: when
testing with QEmu sanitycheck does _not_ spawn QEmu; it relies on "make
run" instead.
Searching the code for "Spawning" now cycles directly to all the places
starting processes and threads.
- Sample -v -v verbose output (lines wrapped for commit message check)
Spawning QEMUHandler Thread for \
qemu_x86/samples/hello_world/sample.helloworld 'make run'
- native_posix example:
Spawning process /home/.../sanity-out/native_posix/\
/samples/hello_world/sample.helloworld/zephyr/zephyr.exe
Spawning BinaryHandler Thread for native_posix/\
samples/hello_world/sample.helloworld
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Fixes the compile errors in various platforms like:
* sam_e70_xplained (too few network buffers)
* galileo, cc3220sf_launchxl and mps2_an385 (missing random number
generator configuration options)
Fixes#15878
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Since west's main.py relies on the args tuple with the returncode
and the cmd, create the CalledProcessError using the correct
positional args.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
