Added some preprocessor directive so that code get compile
for some more nRF52 boards which has only one LED & one button.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Changes in MOVE message handler are as per Mesh Model
Specification which says:
"Upon receiving a Generic Move Set message, the Generic Level
Server shall respond with a Generic Level Status message.
The target Generic Level state is the upper limit of the
Generic Level state when the transition speed is positive,
or the lower limit of the Generic Level state
when the transition speed is negative."
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Removed global variable 'default_tt' & code depend on it
which is redundant as per latest implementation.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Added support of constrain_temperature() function.
Used constrain_lightness() & constrain_temperature()
whereever possible.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Separately saved default & last target values of lightness,
temperature & delta_uv on flash (using settings layer).
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Handle invalid ACL flags in HCI transport.
Only Point to Point is supported over HCI in both directions.
Fix flushable start HCI ACL packets not allowed on LE-U connections
from Host to controller.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add utility to extract the flags Packet Boundary and Broadcast to the
hci.h together with the rest of the ACL data header definitions.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fetch HW models from a new west module.
And, remove all pre-west glue which was used to:
* Fetch them in CI
* Validate their vesion
* Modify the include path and link to them
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Newer SoCs like SAME54 provide dedicated registers to store
the USB trim configuration.
Use those registers if they are defined in ASF to access the
calibration data.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
On newer sam0 SoCs peripherals are enabled through the MCLK
instead of the PM register.
Use the MCLK register if it's availiable.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Newer SoCs like SAME54 have multiple IRQs for the USB peripheral.
Automatically enable all IRQs configured in the DTS.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
In bt_l2cap_br_chan, rx.cid is the local cid and tx.cid is the
remote cid. According to Core-5.0 Vol3.Part A 4.6-4.7,
l2cap_br_remove_tx_cid should be searched using tx.cid
Signed-off-by: ZhongYao Luo <LuoZhongYao@gmail.com>
Some incorrect indenting in the doc was causing numbered lists to reset
back to 1 instead of continuing the series.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
According to BT Spec v5.1 Vol 2 Part E Section 7.8.16, if the
device is already in the White List, the controller should not
add the device to the White List and should return success.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
According to BT Spec v5.1 Vol 2 Part E Section 7.8.16, if the
device is already in the White List, the controller should not
add the device to the White List and should return success.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
A recent patch changed the default ISR stack size for bbc_microbit
which causes this app to consume more RAM than is available. Fix this
by specifying an explicit stack size.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This commit introduces the variable:
ZEPHYR_${MODULE}_MODULE_DIR that can be used for modules to obtain
locations of other modules.
As example: a module which requires the knowledge of mcuboot con now
fetch this information using ZEPHYR_MCUBOOT_MODULE_DIR.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
If the whitelist already exists in the controller then the controller
should not add the device tot the whitelist and should return success.
In that case the counting of entries in the whitelist in the host will
be wrong.
Remove all whitelist counting in the host, and instead rely on the error
reported by the controller for this.
The controller should return error if the whitelist is full.
The controller should return error if use of whitelist was requested but
the whitelist was empty.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
We break out of the while loop on a 2 count then we assert on 2, this
seems to never fail. Count to the end and then assert.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This option, if set, will add arguments to CMake whenever a new build
system is being generated.
It doesn't affect other invocations of CMake, such as when cmake(1) is
run in build tool mode to actually compile the application.
See the documentation changes for details.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Adds a device tree nexus node to define which gpio pins are mapped from
the soc to the arduino header.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a device tree nexus node to define which gpio pins are mapped from
the soc to the arduino header.
The frdm_kw41z board excludes the arduino A0 pin because it cannot be
muxed as a gpio on the soc.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
