Added device tree nodes and associated headers for
defined uarts on the stm32g0 and stm32g07x 8x parts.
Tested with uart on stm32g071rb disco board with usart3 going to stlink.
Using shell.
Signed-off-by: Kieran Levin <ktl@frame.work>
Convert older DT_INST_ macro use in microchip drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in atmel sam drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in sifive drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in STM32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The primary problem was that the callback was being invoked twice,
which broke the tests.
A secondary issue is that when two level tests occur consecutively the
second will fail. Instrumentation confirms that the registers are
being configured correctly, and ip indicates that the condition was
detected, but the interrupt does not occur. Tests pass as long as no
level test precedes the failing test.
It's not clear whether this is an issue with the PLIC, or the GPIO
implementation (hardware or software). As "normal" GPIO applications
appear to work we'll run with it and keep an issue open.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The Atmel DFP headers define two "component typedef styles": RFO and
NTO; where the latter makes use of bit field structs to access hardware
registers.
The default component typedef style assumed by the DFP headers (i.e.
when `COMPONENT_TYPEDEF_STYLE` is not explicitly defined) is "RFO" and
this is indeed the component typedef style used throughout the Zephyr
Atmel SAM drivers, except in the particular instance which this commit
addresses.
The use of `GMAC_TA_Type` bit field struct, which is an "NTO" style
construct, is no longer possible with the latest DFPs because
conditional compilation checks for the bit field struct definitions
were added to restrict the use of such constructs to only when the
global component typedef style is set to "NTO".
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The new Atmel DFP USBHS component headers provide mode-specific
interrupt register field definitions that replace the generic
definitions (e.g. `USBHS_DEVEPTISR_RXSTPI` for a control endpoint is
now `USBHS_DEVEPTISR_CTRL_RXSTPI`).
This commit updates the Zephyr SAM USBHS driver to use the new
mode-specific interrupt register field definitions.
In addition, it maps the generic definitions to the mode-specific
definitions, as the revision A variant headers (e.g. same70a) in the
latest DFPs, at the time of writing, still provide only the generic
definitions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert older DT_INST_ macro use in esp32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_INST_{0,1,2}_ESPRESSIF_ESP32_UART_IRQ_0 defines to something
non-DT prefixed. This way we know which defines are one's we generate
and which ones are driver created. It should be easy enough to replace
these INST_{0,1,2}_ESPRESSIF_ESP32_UART_IRQ_0 define with DTS generated
one macros once esp32 has interrupt controller support in DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in silab drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in cc13xx_cc26xx drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in stellaris drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds the per CPU address offset for intel_apl_adsp, so
the correct base address can be calculated under SMP.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a rather primitive driver for use with the Intra-DSP
Communication (IDC) on the DSP on certain Intel SoCs. The IDC
generates interrupts from one core to another by writing to
certain registers. This is also being utilized as
the scheduler IPI since it can interrupt other cores.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The DSP wall clock timer on some Intel SoC is a timer driven
directly by external oscillator and is external to the CPU
core(s). It is not as fast as the internal core clock, but
provides a common and synchronized counter for all CPU cores
(which is useful for SMP).
This uses the RISCV timer as base as it is using 64-bit
counter.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The CAVS interrupt controller has different base addresses for
each CPU. When running under SMP, the driver needs to look at
the correct address for the CPU the ISR is running so interrupts
can be dispatched correctly. This adds a function to calculate
the correct base address. Note that each supported SoC may have
different offsets so per SoC config will need to added. Support
for intel_s1000 is added as an example.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The dw_ictl interrupt controller is an interrupt aggregator
supporting multi-level interrupts. Therefore, it needs to be
initialized earlier than any downstream interrupt controllers
and devices.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The cavs_ictl interrupt controller is an interrupt aggregator
supporting multi-level interrupts. Therefore, it needs to be
initialized earlier than any downstream interrupt controllers
and devices.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
It was observed that leaving the pin type configured for i2c for SDA
and SCL results in higher power consumption during standby. So we are
resetting the pin type when bringing the i2c into low power mode, and
setting it back to the correct type when exiting low power mode.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Add a dependency on the I2C resource in the TI Power module,
reconfigure the peripheral upon CPU exiting standby, and add
support for device PM.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Add a dependency on the UART resource in the TI Power module,
reconfigure the UART upon CPU exiting standby, and add support
for device PM.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Adding a dependency on the GPIO resource in the TI Power module, and
configuring the edge detection on pads as a wakeup source.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
z_vrfy_counter_get_value should check the size of memory pointed to
ticks and not the size of the pointer.
Fixes: #22431
Coverity CID :207984
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The shared irq support isn't needed in this driver. We just need to
deal with the fact that some SoCs have only a single interrupt line and
some have three interrupts. We can just ifdef that based on
DT_NUM_IRQS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Calling device_set_power_state() with DEVICE_PM_SUSPEND_STATE then
DEVICE_PM_OFF_STATE creates an assert in nrf driver
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
In the default configuration of the stm32g4 is the dual bank mode.
In dual bank mode, the flash is split into two banks with 256k each.
The erase pages have a range form 0 to 127, where each page has 2k.
If one wants to erase an area above 256k, the driver has to switch
to bank 2 befor erasing. Otherwise it will erase the page moulo 127.
Signed-off-by: Alexander Wachter <alexander.wacher@leica-geosystems.com>
This commit introduces some logs in the stm32 flash implementation.
Thith the logs it is easier to locate problems when they arrise.
Signed-off-by: Alexander Wachter <alexander.wacher@leica-geosystems.com>
A txcnt of zero prevents transmission, as transmit requires the number
of entries in the transmit fifo to be strictly less than the txcnt
value. Set the default to 1.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Convert the driver to use DT_INST_ defines, update all dependent dts,
soc and board files.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This allows us to start using DT_NODELABEL() to access SPIMs that way,
instead of via an alias.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
uart_configure verification handler was missing what would cause a crash
if called from a user thread.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add the get_entropy_isr API function for the gecko entropy
driver. When the function is invoked without the ENTROPY_BUSYWAIT
flag, it returns whatever data is available in a non-blocking manner.
Signed-off-by: Pooja Karanjekar <pooja.karanjekar@lemonbeat.com>
Starting a SMI write operation without waiting for completion of the
preceding SMI read operation cause the write operation to fail if
the time between the 2 operations it too short. This leads to the
PHY being in an unusable state on the MIMRT1060-EVK eval board.
In addition the value of the register was not used, as consequence
some bits were not preserved.
The solution is to do a read/modify/write to set only the
ref clock bit, which sets the PHY into 50MHz clock mode,
and keep the value of the other bits.
Signed-off-by: Armand Ciejak <armand@riedonetworks.com>
Force PHY normal operation in eth_mcux_phy_setup in case strap-in
pins configure the PHY in factory test mode.
Signed-off-by: Armand Ciejak <armand@riedonetworks.com>
Don't use DT_INST_0_SOC_NV_FLASH_LABEL as device name.
Use DT_FLASH_DEV_NAME instead
Fixes#23678
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
At OpenThread stack on ieee802154_radio_handle_ack method the
net_pkt_read fail because net_pkt_cursor wasn't proper initialized.
This ensures that net_pkt_cursor is initialized for any ack frame.
Another hidden problem fixed was the frags property on net_buf. Now
it is defined as NULL to ensures that no fragments are available.
The ack frame should be returned to OT only if requested. In this
case, the IEEE 802.15.4 Frame Control field from TX frag is now
verified for an ACK request and if OT requires ACK response it will
be proper handled and dispatched.
Fixes#23595
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit reworks the Xilinx TTC timer driver to use the "match" mode
instead of the "interval" mode which counts up to the specified value
and resets to zero.
Using the "match" mode ensures that the timer keeps counting even after
an interrupt is triggered, and facilitates the tickless mode support
implementation.
This also allows `z_timer_cycle_get_32` to return the correct cycle
count when interrupt is locked; thereby, fixing the k_busy_wait hang
issue.
Note that the TTC "match" mode emulation (and tickless timer operation)
is only stable when the QEMU icount mode is enabled.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This adds support for the Espressif ESP8266 and ESP32 devices to be used
as peripherals on a UART.
There are two main AT command versions that can be selected, 1.7 and
2.0. Since they behave a bit different it is important to select the
one that matches the used in the firmware on your device.
When downloading large amounts of data it is highly recommended to
enable CONFIG_ESP_PASSIVE_TCP and flow control on the UART so that
data is not lost due to UART speed or receive buffer size.
Currently unsupported:
- Changing UDP endpoint with a sendto()
- Bind to a specific local port
- Server socket operations, ie listen() and accept()
Official AT firmware for ESP8266 and ESP32 can be found at:
https://github.com/espressif/esp-at
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
This commit adds the "monitor task" to detect and report any changes
in the PHY link status to the operating system.
The monitor task is perodically executed to poll the link status from
the PHY and call `net_eth_carrier_{off,on}` based on the detected
link status change.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The `link_configure` function currently configures the `GMAC_UR`
register and forces the RMII interface.
This is not necessary because the `GMAC_UR` register is already
configured with an appropriate value based on `CONFIG_ETH_SAM_GMAC_MII`
in `gmac_init`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the PHY link status query function that can be used
for detecting the Ethernet connection.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The IIS2MDC is a 3D digital magnetometer ultra-low power sensor
for industrial applications, which can be interfaced through
either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2mdc.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Added return -ENOTSUP in uart_rx_enable() if RX pin is disabled.
Fixed power management call where TASKRX was started even though
RX pin was disabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Extended nrf_uart driver to support TX only.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add a fixed clock to the qemu-virt-a53.dtsi to match how the musca dts
files work so we get the clock DT info in the same way in the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add interface name to link up/down information message
to help tracking which port is changing status.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
Copy paste error, base address of second controller was set to the
same as the first one, corrected to ENET2.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
With Ethernet controller base address is not straight forward
to figure out if it is ENET or ENET2l, using name is much better.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
This will allow having a different PHY address for each controller.
It also avoids for the PHY address to be hard-coded in several
functions.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
Add new config allowing to enable the second Ethernet port
on i.MX RT1060 SoC family.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
Source and destination ports should be set properly
when assembling the receive socket data.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
Coverity doesn't invoke the build for this module with a configuration
that provides a non-zero delay for entering or releasing deep power
down, so it sees a check that a value known to be non-negative
magically became negative without being touched, and so screams about
dead code.
Refactor to make the adjustments unconditional which has the same
effect in any reasonable level of optimization while making it
slightly less obvious that the value may not change.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add entropy driver based on GECKO TRNG module along with device
tree support for EFM32PG and EFR32MG SOCs.
Signed-off-by: Pooja Karanjekar <pooja.karanjekar@lemonbeat.com>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This reverts commit 979ed4e1cd.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add a missing include of debug/stack.h in order to fix the
compilation warning on implicit declaration of log_stack_usage().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Reworked calibration to not use HW platform which is not available on
some platforms (nrf53) and does not bring any value compared to using
system timer. Switched to use k_timer. Additionally, improved
calibration algorithm to request also LF clock before starting
calibration. This simplifies the algorithm because it does not need
to support disabling low frequency clock which in calibration.
Tests has been updated and simplified. Former tests relied on HW timer
event.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit fixes the field definition names for `GICD_ICFGR`, which
were incorrectly prefixed with `GICC_`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Change adds waiting until PWM is stopped before restarting it. Without
the change, calling the pwm_nrfx_pin_set function multiple times in
quick succession could cause a race condition causing the PWM to
remain stopped in case it should be restarted.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
The ISM330DHCX is a ultra-low power IMU with a 3D digital accelerometer
and 3D digital gyroscope tailored for Industry 4.0 applications, which
can be interfaced through either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/ism330dhcx.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
LPUART1 TX alternate function number for PB6 was not correct in the
pinmux settings for H7 series.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
With new NXP HAL, MCUX CSI does not necesseraly start the
capture into the first submitted buffer. However the driver
expects that buffers will be captured in submitted order.
Fix that.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
k_mem_pool_malloc reserves some space for block descriptor at the start
of the data block, causing misalignement of returned video buffer.
In our context we want to return a video buffer with aligment matching
the video buffer poll alignment config. Fix that by using the simpler
k_mem_pool_alloc function.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
After RX is disabled during receiving, some bytes are received to
internal fifo. To not interfere with further transactions fifo has to be
flushed.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Add Virtual LAN support to stm32 Ethernet driver. Refactor the
eth_iface_init() and move device configuration settings to
eth_initialize() as the eth_iface_init() is called multiple
times (once / configured VLAN).
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Towards cleaning up (and hopefully removing dts_fixup.h in the near
future). We need to move the handling of different names for the irq
flag propety into the driver and out of dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Towards cleaning up (and hopefully removing dts_fixup.h in the near
future). We need to move the handling of different names for the irq
flag propety into the driver and out of dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch is setting the pin to very high speed for all
the SPI2 clock outputs, for the stm32f7 soc series.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Convert usb_stm32 driver to use of DT_INST macros.
Since driver is compatible with 3 different dt compatibles and
compatible string is included in DT_INST macros, I've kept the
DT_USB_ compatible agnostic macros based on DT_INST ones, which
allowed to remove fixup definitions.
Use of DT_USB symbols is now limited to usb_dc_stm32.
Additionally, compatible "st,stm32-otgfs" is removed from list
of compatibles for usbotg_hs ips.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
In the process, we've removed all UART/USART/LPUART code in
device instanciation code which had no impact.
Since all uart/usart/lpuart nodes declare compatibility with
st,stm32uart, DT_INST_X_ST_STM32_UART_FOO could be used.
Removed DT_UART fixup macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On stm32 spi devices, there are 2 main IP variants, with and w/o
fifo. Fifo is not really used today, but still there is some
additional code handling fifo. Today this code is protected under
Kconfig symbol SPI_STM32_HAS_FIFO.
This code carries redundant information vs dedicated compatible
"st,stm32-spi-fifo", which is provided as unique driver compatible
for devices supporting this IP as opposed to use of "st,stm32-spi"
when fifo is not supported.
Having these 2 compatibles defined exclusively is not convenient for
migration to DT_INST as DT_INST macros contain compatible string and
hence it cannot be used to provide common compatible code for devices
defining different compatibles.
Based on these observations, review stm32 spi devices compatible
declarations. Devices supporting fifo will now declare both
compatibles, as proposed by dt spec: "[compatible] property value
consists of a concatenated list of null terminated strings,
from most specific to most general". Hence field will now be:
"st,stm32-spi-fifo", "st,stm32-spi"
This way, fifo enabled stm32 spi devices will generate both:
DT_INST_STM32_SPI_FOO and DT_INST_STM32_SPI_FIFO_FOO
As well as:
DT_COMPAT_ST_STM32_SPI and DT_COMPAT_ST_STM32_SPI_FIFO
So, DT_INST_STM32_SPI_FOO could be used for device initialization.
Also DT_COMPAT_ST_STM32_SPI_FIFO could be used for FIFO handling
code inside driver. Hence use it to replace Kconfig symbol
SPI_STM32_HAS_FIFO.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
Removed DT_FLASH_DEV fixup macros, except DT_FLASH_DEV_NAME
used in applications.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
Removed DT_RTC_0 fixup macros but keep DT_RTC_NAME_0 as it is
still in use across RTC users.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The RX fragment debug print does not work (compile error)
if memory allocation debugging is enabled, so disable it
for time being.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In the DT_INST conversion we introduced a typo bug of accessing port0
instead of port1 in the IRQ config function.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configure the PWM period and pulse width in timer ticks instead of
calculating the frequency and duty cycle for use in the higher level
MCUX API. This improves the resolution of the PWM output signal
considerably.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The IIS2DLPC is a 3D digital accelerometer ultra-low power sensor
for industrial applications, which can be interfaced through either
I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2dlpc.pdf
This driver is based on stmemsc i/f v1.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Telnet console was move as a shell backend and is not anymore part of
console drivers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Enable counter driver support for H7 series. Tested with H743ZI MCU
using samples/drivers/counter/alarm.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The current design of the network-specific stack dumping APIs
is fundamentally unsafe. You cannot properly dump stack data
without information which is only available in the thread object.
In addition, this infrastructure is unnecessary. There is already
a core shell command which dumps stack information for all
active threads.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Update device data with the activated configuration, so that it
will be remembered for follow up configuration get requests.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Change to code to use the automatically generated DT_INST_*
defines and remove the now unneeded configs and fixups.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
The sole purpose of init options has been to enable hardware flow
control on NS16750 when asked. Use the proper DTS tags for this.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Expand configuration mechanism for additional eSPI host warnings.
Notify client driver when sleep A virtual wire is received.
Simplify virtual wire interrupt enabling.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
There is timeout guard, in form of k_sem_get within work_in_time_slice,
used to detect if flash operation takes longer than expected maximum
and to return error code in such case. The processing of this timeout
is missing cancellation of scheduled ticker job that would attempt to
perform another operation. This causes problem as context for ticker
is created, on stack, within erase/write_in_timeslice which
would conclude when timeout occurs, folding the stack in process.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Added locking for TX transfers between async and polling API.
Added safety counters for checking if transmission finished.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Add locking between async and polling tx transfers.
Add safety counters while waiting for transmission to finish.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
The current Generic Interrupt Controller (GIC) driver makes use of the
multi-level interrupt mechanism and `irq_nextlevel` public interface.
This is a less-than-ideal implementation for the following reasons:
1. The GIC is often used as the main interrupt controller for the
Cortex-A and Cortex-R family SoCs and, in this case, it is not a 2nd
level interrupt controller; in fact, it is the root interrupt
controller and therefore should be treated as such.
2. The only reason for using `irq_nextlevel` here is to interface the
architecture implementation to the interrupt controller functions.
Since there is no nesting or multiple instances of an interrupt
controller involved, there is really no point in adding such an
abstraction.
3. 2nd level topology adds many unnecessary abstractions and results
in strange coding artefacts as well as performance penalty due to
additional branching.
This commit refactors the GIC driver interface as follows:
1. Remove the current GIC driver interface based on the multi-level
interrupt mechanism and the `irq_nextlevel` public interface.
2. Define the GIC driver interface in
`include/drivers/interrupt_controller/gic.h` and allow the arch
implementation to directly invoke this interface.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
MEC15xx eSPI OOB RX length register holds received message length
and receive buffer length, need to extract rcvd msg length.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
for smp target, there is a case where just one core is running, then:
* during init, the master core will run, others cores will halt/sleep
* use timer driver for single core
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Add CAP_NO_IV_PREFIX capability support to the STM32 CRYP crypto driver,
so the initialization vector does not have to be prefixed to the
plaintext/ciphertext buffer.
Signed-off-by: Markus Fuchs <markus.fuchs@de.sauter-bc.com>
The loopback driver is a simple driver that can be used to
test CAN subsystems. The actual implementation sends frames
in the same thread that calls the send function.
Some libraries have problems with that behavior.
This PR implements a dedicated thread that calls the callback
for the receiving functions and a msgq in between the sender
and the TX thread.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Attempt to deinitialize an nrfx driver that is not initialized results
in an assertion failure reported by the driver. And such attempt could
happen in SPI shims when the power state was switched between states
other than ACTIVE.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use DT_INST_* instead of the hard-coded macro from the HAL,
as DT_INST_* are preferred.
Fixes#17775
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Some commands need to be processed before a "\r\n" is available and
there might also be commands that have "\r\n" as data but doesn't mean
the end of the command.
To solve this a MODEM_CMD_DIRECT has been added. cmd_handler_process()
will look for matching direct commands before checking if a whole line
is available for matching the normal commands.
A direct command can return either -EAGAIN, meaning that more data is
needed or it will return the number of bytes to skip forward, ie the
length of the command that was handled.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
Introduces a new SDL mouse driver for the keyboard scan (kscan)
interface. Driver is implemented as SDL event filter
Signed-off-by: Pavlo Hamov <pavlo_hamov@jabil.com>
Convert driver to use DT_INST_ defines. The preferred defines for
drivers are DT_INST_. The driver mostly used DT_INST_ defines but
a few IRQ priority defines needed conversion.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. The preferred defines for
drivers are DT_INST_.
As part of this change we utilize the device tree for GIRQ info and
rename timer3 to 2 since we are doing this by instance number.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. There was just one case for
CS_GPIOS that wasn't using DT_INST defines already.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to fully use DT_INST_ defines. Currently IRQs are not
generated from DTS on esp32 so we create #defines for what they should
look like. Convert the IRQ defines to match DT_INST style so if/when
we have that info in DTS it will look the same.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. Replace dts_fixup.h use
for DT_RTC_0_NAME with DT_INST_0_NXP_KINETIS_RTC_LABEL to be
consistent. Also, remove the aliases that had been used for this
driver in various nxp_k*.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines and remove Kconfig per instance
enablement in favor of DT_INST_ define existing. Also, remove the
aliases that had been used for this driver in nxp_rt.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert pms7003 sensor driver to utilize device tree.
DTS would look something like the following for the pms7003:
uart {
pms7003: pms7003 {
status = "okay";
compatible = "plantower,pms7003";
label = "pms7003";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ak8975 sensor driver to utilize device tree.
This also supports the ak8975 embedded in a invensense MPU9150. In such
a case the device tree node should look something like, where the ak8975
is a child of the mpu9150.
mpu9150@68 {
compatible = "invensense,mpu9150";
reg = <0x68>;
label = "mpu9150";
#address-cells = <1>;
#size-cells = <0>;
ak8975@c {
compatible = "asahi-kasei,ak8975";
reg = <0xc>;
label = "ak8975";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix build failure when CONFIG_NET_L2_OPENTHREAD is not enabled. The
failure looks as follows:
drivers/ieee802154/ieee802154_nrf5.c:187:12:
warning: 'nrf5_energy_scan_start' defined but not used
[-Wunused-function]
static int nrf5_energy_scan_start(struct device *dev,
^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Previously, endpoint configuration would reserve memory in the packet
memory area which would never be reclaimed. After this patch, endpoints
will reuse previously allocated memory when possible. We still leak
memory when reconfiguration increases the max packet size for a given
endpoint number, but this fixes the common case.
Bug: https://github.com/zephyrproject-rtos/zephyr/issues/23178
Signed-off-by: Josh Gao <josh@jmgao.dev>
Update hal_nordic's revision, so that NRFX_ASSERT uses __ASSERT_NO_MSG
directly, not through the assert macro that comes from from libc,
as the definition of the latter might be different when some specific
libc version is used, and this could generate troubles.
Replace also uses of assert() with __ASSERT_NO_MSG() in nrfx driver
shims that use this macro without including the corresponding header
file (i.e. that implicitly rely on assert.h being included from
nrfx_glue.h, which is no longer the case).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Rework USB_DeviceNotificationTrigger(). Fix style.
Drop messages from USB_DeviceEhciCancel().
MCUX EHCI driver notifies about canceled transfers,
but there is no specific code for this event in
usb_device_callback_message_struct_t, the only way to
recognize it is to check the length value.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
User is currently able to enable verbose packet debugging for
received packets. This commit enables the same for sent packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
With this patch, the specific flag IWDG_STM32_START_AT_BOOT
is replaced by the zephyr generic WDT_DISABLE_AT_BOOT.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Implement function and necessary callbacks to handle Energy Scan feature
of the nRF radio driver needed by some radio stacks.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
Data toggle should be reset after SetConfiguration or
SetInterface request.
Always reset data toggle in usb_dc_ep_enable.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
USB Host expects dtoggle to be cleared after ClearFeature(Halt):
"[...] clearing the Halt feature via a ClearFeature(ENDPOINT_HALT)
request results in the endpoint no longer returning a STALL.
For endpoints using data toggle, regardless of whether an endpoint
has the Halt feature set, a ClearFeature(ENDPOINT_HALT) request always
results in the data toggle being reinitialized to DATA0."
- Subsection 9.4.5 of usb 2.0 spec (usb_20.pdf)
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Add I2C and SPI bus communication routines in separate files,
and register one or the other as read/write callbacks based
on bus selection in DTS.
This commit is fixing issue #22348 as well, as the SPI part
is handling in the proper way the CS GPIO part.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
mtls_session_setup checks early if the given mode is valid and return
an error if not. CRYPTO_CIPHER_MODE_CTR is not a valid one so there is
no needed to have it in the switch.
CID: 20600
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The `irq_update` UART API function must always return 1 according to
the API documentations.
This commit fixes the `irq_update` API function to unconditionally
return `1`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The `irq_update` UART API function must always return 1 according to
the API documentations.
This commit fixes the `irq_update` API function to unconditionally
return '1'.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit fixes the multiple SERCOM interrupt handling for the SAM
D5x and E5x devices by replacing the obsolete device tree symbol with
the new `DT_INST` symbol.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Since driver is shared with other devices, it must be enabled
conditionally based on the number of instances. This avoid show
invalid options for devices with lower port count like SAM4S/SAM4E.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
SAMV71 uses same driver of SAME70 and this enables the feature. Since
driver is shared with other devices, it must be enabled conditionally
based on the number of instances. This avoid show invalid options for
devices with lower port count like SAM4S/SAM4E.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
When added SAM4E and SAMV71 platform the huge amount of refactor left
out this two configurations. This add missing configuration for all
supported devices.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Instead of hardcoding the "zeth" network interface name, use the
name defined in Kconfig so that user can change it if needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move auto-negotiate sequence from driver initialization to link up event
Previously when booting without ethernet cable connected the
initialization would fail and never recover.
Now we can connect the ethernet cable any time and multiple times.
This also drastically reduces boot time to main.
Logging Link up and Link down events.
Logging speed and duplex from eth_gecko logger instead of eth_gecko_phy.
Signed-off-by: Luuk Bosma <l.bosma@interay.com>
pin is an unsigned variable so there is no meaning check if it is less
than zero.
CID :208407
CID :208408
CID :208410
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The rx timeout timer callback need update trx_state variable and this
variable is protected by a mutex. Because of that, when compiling the
system with CONFIG_ASSERT=y the system reports 'ASSERTION FAIL
[!arch_is_in_isr()] @ ZEPHYR_BASE/kernel/include/ksched.h:262'.
This refactor the driver remove trx_state variable dependency and
consequently removes phy_mutex and rx timeout timer to be compliant
with kernel rules.
Fixes: #23198
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The current version of at86rf2xx RX implementation don't uses advanced
capabilities offer by the transceiver. This access SRAM space to gatter
PHR information in parallel with transceiver frame reception. It allows
improve RX reception by handling properlly the frame protection feature
removing transceiver states changes.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Current rf2xx_thread_main code have too many if/for/while imbrication.
Extract methods from rx2xx_thread_main for better readability.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Do not use the content of the status register to write into the
override register because it may have unpredictable effect,
instead to a read/modify/write on the override register.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
It is necessary to poll the ENET_EIR_MII bit before reading
the data register as explained in the i.MX RT1060 reference
manual in chapter 41.7.17.4.
Use PHY_* functions from NXP HAL to correctly access the PHY
registers.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
This enables the ADC output data to be shifted right when using
10-bit resolution. Or else, data would be left justified as if
it's doing 12-bit ADC with the right 2 bits filled with zeroes.
Fixes#23202
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This commit fixes the multiple SERCOM interrupt handling for the SAM
D5x and E5x devices by replacing the obsolete device tree symbol with
the new `DT_INST` symbol.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Improve priority queue conditional build. Now priority queue code is
enabled only if device have support to it. This enables GMAC driver
for devices with only one queue for RX/TX.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The Atmel SAM SoC with ethernet port uses same GMAC driver. However,
there are differences between SoC GMAC implementation. Some SoCs have
priority queue and system can configure 0 up to 5, depending of SoC
version. This update current GMAC driver adding missing definitions.
Co-authored-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add missing queue entries for sam gmac. This update the queue selection
to proper handle all supported SAM SoC that uses GMAC driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The first revision of the SAM E70 soc had three queues. The current
revision B has six queues. If we don't initialize all queues, the DMA
engine gets stuck when trying to read a descriptor from NULL. To enable
the initialization of the additional queues, the correct soc has to be
selected in the config options, f.ex. CONFIG_SOC_PART_NUMBER_SAME70Q21B
instead of CONFIG_SOC_PART_NUMBER_SAME70Q21.
Also rename GMAC_QUEUE_NO to GMAC_QUEUE_NUM as requested during review.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
When debugging on a long running platform, the MCU may get reset by
the debugger with an ndmreset toggle. Since there is no requirement
that this resets anything in particular on the platform, the CLINT
registers may not get reset. When this occurs with an mtime register
value that is larger than 32 bits the riscv machine timer will
continuously interrupt the system when the mtime register exceeds 32
bits in value. This is because the last_count value is used to update
the mtimecmp register, and its value is initialized to zero. Its
first update is with a 32-bit value, which loses information when the
mtime register exceeds 32 bits.
The proposed solution is to set the last_count value to the current
value in the mtime register when the timer is initialized. Since the
timer is fired at intervals that are less than 32 bits in value, the
next update of last_count will remain valid, and the system will
function as expected.
Signed-off-by: Jaron Kelleher <jkelleher@fb.com>
This reverts commit 382e6fbccf.
Disabling watchdog at boot breaks watchdog API contract. Production
firmware should never ship with the option enabled. Unfortunately, this
is dangerosly easy to overlook. If left enabled, in the best case, it
will degrade functionality of the subsystem. In the worst case it
will leave watchdog permanently disbled.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
CLOE (Code Loop Optimization) does not exist on SAM3x.
Make the EEFC_FMR_CLOE disable depending on CONFIG_SOC_SERIES_SAM3X.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Include stm32XXxx_ll_utils.h in soc.h for every stm32 SoC,
if CONFIG_HWINFO_STM32 is selected.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Make the NRF hwinfo driver depending on !TRUSTED_EXECUTION_NONSECURE
because the FICR registers are not accessible from the non-secure
world.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Introduce the HWINFO_HAS_DRIVER Kconfig symbol to get
the information if hwinfo is supported on the current platform.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
This patch activates the boost mode for the main regulator
when the system frequency above 80MHz for stm32l4Rx/stm32l4Sx
soc series.
To save power, the boost mode should be disabled below 80MHz.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patch activates the boost mode for the main regulator
when the system frequency above 150MHz for stm32g4xx soc series.
To save power, the boost mode should be disabled below 150MHz.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patches add a delay after setting the watchdog
to wait for the register (Prescaler and Counter registers)
to be updated before leaving (until LL_IWDG_IsReady is true)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
SMI initialization is required to enable PHY communication.
PHY setups needs to run after SMI initialization.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
The LIS3MDL sensor provides two different pins for handling
interrupts: the DRDY, that triggers new data sample availability,
and INT, that goes off when data sample exceeds a given threshold.
The driver handled data ready triggers only, which does not
require sensor configuration at all. Moreover a dummy read is
required when the data ready is configured to re-trigger a new
interrupt.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
If IO APIC is in logical destination mode, local APICs compare their
logical APIC ID defined in LDR (Logical Destination Register) with
the destination code sent with the interrupt to determine whether or not
to accept the incoming interrupt.
This patch programs LDR in xAPIC mode to support IO APIC logical mode.
The local APIC ID from local APIC ID register can't be used as the
'logical APIC ID' because LAPIC ID may not be consecutive numbers hence
it makes it impossible for LDR to encode 8 IDs within 8 bits.
This patch chooses 0 for BSP, and for APs, cpu_number which is the index
to x86_cpuboot[], which ultimately assigned in z_smp_init[].
Signed-off-by: Zide Chen <zide.chen@intel.com>
Currently IO APIC is working in physical destination mode, which
doesn't support interrupt to be delivered to multiple local APICs.
By definition only 4 bits [59:63] in IO APIC IOREDTBL register are
available for destination addresses and it contains an APIC ID only.
This patch changes it to logical destination mode so that IOREDTBL
can potentially define a set of processors and it's posible to deliver
interrupts to multiple APICs.
Also it changes delivery mode from fixed to lowest priority. The reason
being in fixed mode, the interrupt could be delivered to all CPUs
which put burden in software to handle repeated interrupts. While in
lowest priority mode, interrupt is delivered to one local APIC only.
Signed-off-by: Zide Chen <zide.chen@intel.com>
During driver rewrite, the field to specify the base address of
the interrupt controller was dropped, which results in error in
device initialization due to accessing random address (or null).
Fix it by specifying the base address.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
On stm32f302/3 series, USB and CAN_1 share same IRQ lines.
To use USB and CAN_1 together, USB IRQ could be remap to other
line numbers, on which there is no conflict.
Remap the USB IRQ lines by default:
-Assign remap number in matching dtsi files
-Perform remap before usb driver init
Additionally, fix compilation issue in usb driver.
Fixes#22343
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Disabling gpio interrupts on the pin prior to changing its interrupt
type to level-based helps prevent spurious interrupts that would be
otherwise observed, if gpio interrupts were originally enabled when
gpio_cc32xx_pin_interrupt_configure() is invoked.
Fixes#22847
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
In the gpio isr, gpio interrupts are disabled when invoking the
registered callbacks. This is unnecessary, and causes a problem if the
callback attempts to disable gpio interrupts by reconfiguring the pin
as in the test gpio_basic_api.
Fixes#22847
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Include gpio_utils.h to fix a build failure:
gpio_pca95xx.c:490:20: warning: implicit declaration of
function 'GPIO_PORT_PIN_MASK_FROM_NGPIOS'
[-Wimplicit-function-declaration]
gpio_pca95xx.c:490:20: error: initializer element is not constant
.port_pin_mask = GPIO_PORT_PIN_MASK_FROM_NGPIOS(
DT_INST_##inst##_NXP_PCA95XX_NGPIOS), \
Signed-off-by: Göran Weinholt <goran.weinholt@endian.se>
In order to overrdie a choice one needs to define it again. Override it
by redefining it in the .defconfig file.
See #22474.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The data_first flag was intended to be set when the configuration
requires setting the output value before setting the direction.
Respect the intent.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Kconfig.rv32m1 is already 'source'd within an 'if ENTROPY_GENERATOR', so
ENTROPY_RV32M1_TRNG does not need a 'depends on ENTROPY_GENERATOR'.
Flagged by https://github.com/zephyrproject-rtos/ci-tools/pull/128.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
setting/resetting endpoints is required when switching to alternate
interfaces. This is a common operation for usb audio class.
When audio device is enumerated host invokes set_interface request
to alternate with 0 endpoints associated. That operation lead to
disable never enabled endpoints. With previous solution error message
will appear.
This commit limits error messages to be present only if endpoint
was configured/enabled before and there was a problem when trying
to configure/enable it for the first time.
* Kinetis driver was updated with return error value when ep was
already configured/enabled.
* nxp driver updated with return error value when ep was already
enabled
* sam0 driver updated with return codes instead of magic numbers.
This is fix patch to #21741
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Move PWR init code out of clock control driver and
put SMPS related function under SMPS condition as it
is not supported by all soc variants of the series.
Fixes#22363
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
usage of AT+UPSD command per UBX-17003787(R15) command reference is:
AT+UPSD=<profile_id>, <param_tag>, <param_val>
For AT+UPSD=0, 1, "<value>": we are setting value to MCCMNO, which
is technically incorrect. <param_tag> of 1 means:
1: APN - <param_val> defines the APN text string, e.g.
"apn.provider.com"; the maximum length is 99. The factory-programmed
value is an empty string.
Let's use APN here instead. This fixes a +CME ERROR: 113 when
connecting with U2 modem.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/22689
Signed-off-by: Michael Scott <mike@foundries.io>
Add Kconfig option that allows user to set MCC (Mobile Country
Code). If user does not set it, then automatic operator
registration is used.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Misc fixes / enhancements to the GSM driver:
* set the \r as a line ending character
* make gsm_init() static as there is no need to expose it
* print the gsm context pointer at init
* set buffer allocation timeout to modem context so that it is
not infinite
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of using global static variable "gsm" everywhere,
store the context when calling DEVICE_INIT(). Then in the device
init function get the context from the device struct. This way
it is possible to use the same functions for implementing two
gsm modem instances. Currently this is not fully possible because
the context is not passed via uart_pipe API and modem_cmd
callbacks. So some future work would still be needed.
In practice this commit does not change anything, it just makes
it a little bit easier to have two instance of this modem which
might be quite unlikely case. Anyway, the driver now follows the
same style how some other drivers are done like Ethernet etc.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Now that the u-blox driver can let cmd_handler know that it hasn't
received enough data, let's disable the hex mode for readying
binary data.
On the SARA-R4 this mode limits the receiving MTU to 512 which is
unacceptable.
Signed-off-by: Michael Scott <mike@foundries.io>
Some modem commands can determine if they have enough data pulled from
the modem to continue or not. Let's allow those functions to return
EAGAIN which means there's more data needed from the modem.
Signed-off-by: Michael Scott <mike@foundries.io>
Modem commands are setup with arg_count to denote the number of params
to parse before returning. Let's honor that setting and return once
we've parse them.
This fixes a run-on bug where the parser would find as many of the
parameters via the supplied delimiter as it could.
Signed-off-by: Michael Scott <mike@foundries.io>
The original Ublox SARA-R4 driver was written for the net_context
APIs. As a result many of the return values are not POSIX standard.
Let's go through all of the socket offload functions and make sure
we return standard values (0 or -1) and set errno where appropriate.
Signed-off-by: Michael Scott <mike@foundries.io>
SARA-R4 has a max read limit of 512 when using binary hex formatting.
Otherwise the max read limit is 1024.
Signed-off-by: Michael Scott <mike@foundries.io>
New socket functions were introduced to hide some of the modem_socket
internals:
- modem_socket_next_packet_size()
- modem_socket_wait_data()
- modem_socket_data_ready()
Let's use them.
Signed-off-by: Michael Scott <mike@foundries.io>
Let's use sock->is_connected to check whether we need to clean up
the modem's socket. It may have already been closed via URC.
Signed-off-by: Michael Scott <mike@foundries.io>
SARA-R4 AT command manual states +USOCO has a max timeout of 120s.
Let's use that instead of the default 10s command timeout.
Signed-off-by: Michael Scott <mike@foundries.io>
The SARA R412M requires manual activation of the PDP context. It also
reports RSSI instead of RSRP when on 2G. An off-by-one in the RSRP
calculation was also fixed in this commit.
Signed-off-by: Göran Weinholt <goran.weinholt@endian.se>
The u-blox SARA modems have the ability to output the network status
on a GPIO pin. This can be used to light up a LED when the modem is
connected to the network.
Signed-off-by: Göran Weinholt <goran.weinholt@endian.se>
The U2 modem will sometimes not power off even if we have given it the
signal to do so. We now signal it continually until the modem
indicates that power is off with VINT=0.
Signed-off-by: Göran Weinholt <goran.weinholt@endian.se>
This fixes two problems in modem_reset():
- mdata.net_iface is used without checking that it is valid.
Now, we validate mdata_net_iface before usage, and give a warning
if it was not set.
- if the modem does not perform network registration within the
given time of 20s, in the previous implementation the driver
gave up.
Now, the driver disables RF for a second, enables it again and
gives the modem another 20s to register. This has been seen
to help in roaming situations.
Tested on Sara R4.
Signed-off-by: Hans Wilmers <hans@wilmers.no>
- limit max. number of bytes when sending to socket
The number of bytes sent to a socket in one transaction
is limited to 512 in HEX mode (Sara-R4), and to 1024
otherwise. This corresponds to numbers given in the
manual for ublox cellular modems.
- report number of bytes actually sent, as reported by modem
After writing data to a socket, we now return the number of
bytes actually written, as reported by the modem.
Signed-off-by: Hans Wilmers <hans@wilmers.no>
In order to still process 128 bytes at a time, let's add 1 to the
length of match_buf which will be used to store a NUL char when
the match_buf is at max size (size - 1).
Otherwise we're processing 127 bytes at a time which is inefficient
compared to the data buffer sizes in net_buf.
Signed-off-by: Michael Scott <mike@foundries.io>
SARA-R4 modem supports offloaded DNS via AT+UDNSRN command.
Let's implement it.
NOTE! On SARA-R4 a new firmware *IS* required to support this feature:
L0.0.00.00.05.08 [Apr 17 2019 19:34:02]
Signed-off-by: Michael Scott <mike@foundries.io>
Managing the interface up / down events from driver code (as opposed
to L2 layers) has been an issue for quite some time. There are
race conditions which result in data aborts (referencing NULL
iface or NULL iface->if_dev) or ends up breaking ASSERT checks for
non-NULL iface.
Let's remove the handling for now and come up with something better
when a user actually needs it.
Signed-off-by: Michael Scott <mike@foundries.io>
In offload_recvfrom(), if we end up calling modem_cmd_send(),
then we should always wait for the results. We've already
checked for MSG_DONTWAIT and made sure that there is data ready.
We just need to get it from the modem buffer at this point.
Signed-off-by: Michael Scott <mike@foundries.io>
Users may be waiting for data via socket recv() function. We
notify them that data is ready when URC is received from modem.
Once unblocked, we read the data from the modem buffer which
is handled via on_cmd_sockread_common(). At this point, we
don't need to unblock waiting users again.
Signed-off-by: Michael Scott <mike@foundries.io>
The hex_to_binary() function is incorrectly assuming all buffers
passed to recv() will have an additinal byte for storing a NUL
terminating char. This should be optional as MQTT library uses
exact sized buffers for parsing socket data.
Signed-off-by: Michael Scott <mike@foundries.io>
The send_socket_data() is incorrectly sending 0 as successful result.
The socket APIs require the number of bytes sent to be returned.
Signed-off-by: Michael Scott <mike@foundries.io>
For parsing purposes we need to add a NUL to the end of match_buf.
When there is no CR/LF in the incoming rx bufs then we fill match_buf
to its max size. This ended up with an off by one error which was
overflowing match_buf into the following data.
To account for this, let's fill the buffer to size - 1 so that we
leave room for the NUL at the end and stop corrupting data.
Signed-off-by: Michael Scott <mike@foundries.io>
- rename buf_len to match_len for clarity
- pass in modem_cmd_handler_data instead of buffer pointer directly
- buffer adjustments for the command length are kept inside
parse_params()
Signed-off-by: Michael Scott <mike@foundries.io>
Let's add a field which the drivers can use to keep track of whether
they are connected or not. This will normally be enabled / disabled
in the socket connect and URC for socket close notify.
Signed-off-by: Michael Scott <mike@foundries.io>
Let's hide the internals of sock->packet_sizes[] by adding a function
which returns the size of the next waiting packet.
Signed-off-by: Michael Scott <mike@foundries.io>
Let's hide the internals of the modem_socket's sem_data_ready and
poll handling with 2 new functions:
- modem_socket_wait_data: take a semaphore and wait for data
- modem_socket_data_ready: give back the data ready semaphore and
unblock poll() users
Signed-off-by: Michael Scott <mike@foundries.io>
Add lock behavior for functions in modem_socket, to prevent race
conditions when performing socket data maintenance.
Signed-off-by: Michael Scott <mike@foundries.io>
Let's allow protocols to request portions of the current packet.
This is seen in the MQTT library when parsing headers for the type
and variable length of the packet.
This fixes basic parsing done in the MQTT library and probably others.
Signed-off-by: Michael Scott <mike@foundries.io>
I think people might be reading differences into 'if' and 'depends on'
that aren't there, like maybe 'if' being needed to "hide" a symbol,
while 'depends on' just adds a dependency.
There are no differences between 'if' and 'depends on'. 'if' is just a
shorthand for 'depends on'. They work the same when it comes to creating
implicit menus too.
The way symbols get "hidden" is through their dependencies not being
satisfied ('if'/'depends on' get copied up as a dependency on the
prompt).
Since 'if' and 'depends on' are the same, an 'if' with just a single
symbol in it can be replaced with a 'depends on'. IMO, it's best to
avoid 'if' there as a style choice too, because it confuses people into
thinking there's deep Kconfig magic going on that requires 'if'.
Going for 'depends on' can also remove some nested 'if's, which
generates nicer symbol information and docs, because nested 'if's really
are so simple/dumb that they just add the dependencies from both 'if's
to all symbols within.
Replace a bunch of single-symbol 'if's with 'depends on' to despam the
Kconfig files a bit and make it clearer how things work. Also do some
other minor related dependency refactoring.
The replacement isn't complete. Will fix up the rest later. Splitting it
a bit to make it more manageable.
(Everything above is true for choices, menus, and comments as well.)
Detected by tweaking the Kconfiglib parsing code. It's impossible to
detect after parsing, because 'if' turns into 'depends on'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Error codes from DSPI_MasterTransferNonBlocking are now handled in
tranceive to ensure that the context is unlocked when an busy bus
is detected.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
The existing stack_analyze APIs had some problems:
1. Not properly namespaced
2. Accepted the stack object as a parameter, yet the stack object
does not contain the necessary information to get the associated
buffer region, the thread object is needed for this
3. Caused a crash on certain platforms that do not allow inspection
of unused stack space for the currently running thread
4. No user mode access
5. Separately passed in thread name
We deprecate these functions and add a new API
k_thread_stack_space_get() which addresses all of these issues.
A helper API log_stack_usage() also added which resembles
STACK_ANALYZE() in functionality.
Fixes: #17852
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The loramac-node library uses math functions from math.h that
are not included in the minimal lib.
This commit changes the samples project config to always build
with newlib and adds a dependency to newlib.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Move rtt configuration options to drivers/debug and split the
systemview configuration.
drivers/debug will service for this class of drivers that are enabled in
debug mode only and provide a hardware interface to the system.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch adds crypto driver support for all STM32F4 devices providing
a CRYP peripheral.
This driver implements the AES ECB, CBC and CTR modes of operation.
It has been tested on a STM32F437 SoC running the Zephyr crypto driver
sample.
Signed-off-by: Markus Fuchs <markus.fuchs@de.sauter-bc.com>
When building with LLVM we get the following error:
uart_stm32.c:272:9: error: implicit conversion from enumeration type
'enum uart_config_parity' to different enumeration type
'enum uart_config_flow_control' [-Werror,-Wenum-conversion]
return UART_CFG_PARITY_NONE;
~~~~~~ ^~~~~~~~~~~~~~~~~~~~
We shouldn't be mixing parity and flow control enum's. Use
UART_CFG_FLOW_CTRL_NONE instead or UART_CFG_PARITY_NONE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SAM flash driver was developed for the SAME70 SoCs and hasn't ever
been validated on the other SAM families (SAM3X, SAM4S). If we try and
build on one of the other SoC families we get build errors. So limit it
to just SAME70 for now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Compile errors because of missing include file and typos
when accessing variables in the modem_pin struct.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit fixes an incorrect declaration of the buffer_size member
of the i2c_eeprom_slave_config struct.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
ADC_1 peripheral instance was enabled by default in driver.
This is not the usual way to enable peripheral instances, as it
makes board configuration unclear.
Move activation in boards that are declaring ADC support.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added subsys argument to the callback, updated one driver which
used it and test cases.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Use gpio_pin_t uniformly when passing pin indexes to the driver. Use
gpio_flags_t uniformly when passing flags to the driver. Change name
of pin configuration function in API function table to be consistent
with other API functions.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
There is a typedef used to store pin indexes in configuration
structures. For consistency it should also be used to identify pin
indexes in function prototypes.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The only remaining port operations have dedicated API function table
entries. Remove the defines for access op (mode), and remove support
for access op from all implementations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The last external reference to these was removed when the pin
write/read functions were deprecated. Remove the syscall support, API
function table entries, and implementation from all drivers.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
These have been replaced by the appropriate call to
gpio_pin_interrupt_configure(). While the disable function could be
implemented using the new functionality, the enable function cannot
because the interrupt mode is not available. Consequently we cannot
replace these with equivalent functionality using the legacy API.
Clean up the internal implementation by removing the inaccessible
port-based enable/disable feature, leaving the pin-based capability in
place.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the enable callback API with the enable interrupt API, and do
it after the callback is installed.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This API will be deprecated in favor of the new API that clearly
specifies whether it works on logical or physical levels.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Convert to support devicetree.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Mark all CC2520 GPIOs as required
in binding.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use new API to configure and interact with GPIOs. Move GPIO
initialization from sample into driver. The existing physical/line
level control has been kept rather than converting to logical level
signals.
Also improve error messages.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
After startup ublox-sara-r4 code sets the MDM_POWER signal to input
using a deprecated configuration macro. This was the only use of the
modem context API to configure a pin.
Refactor the API to not take the flags as an input but instead select
between the flags to be used when the pin is active and a disconnected
state. Use this API instead of a separate direct configure call when
initializing the modem pins.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update the DRDYB pin interrupt handling code of the TI LMP90xxx ADC
driver to use the new GPIO API.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Update the lora/sx1276 driver to the new GPIO API, using configured
active level and the replacement interrupt and active-sensitive set
APIs.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Document and assign write-protect signal as active low, and use the
active-sensitive API to control it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert to the new GPIO API using logical access, including setting the
GPIO line as active low in the Device Tree source.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use new configuration API, replace callback enable/disable with
interrupt enable/disable, and set active level in devicetree source.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Conver to the new GPIO API using raw access, since the driver
has its own macros to define signal levels.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert to the new API using raw access, since it's a common access
layer shared by multiple (right now only ublox-sara-r4) modems.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update devicetree sources and bindings, switch to new GPIO API. Use
devicetree property name to identify interrupt signal.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update sample overlays. Add GPIO flags to configuration state.
Refactor to split out setup/handle/process phases. Switch to new API
replacing callback dis/enable with interrupt dis/enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure. This driver uses fixups to define a common name
based on the SOC series; until aliases for the new properties are
added the code assumes all pins are supported.
Since pin ordinal validation is now done directly in gpio API,
remove checks inside the driver itself.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the hard-coded device-specific pin count to
initialize it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it. Not all aliases appear to be present, but using instances breaks
because the ports used by different boards do not always start with
the first.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure. The devicetree binding does not inherit from
gpio-controller, so the required property is not available there. A
hard-coded value of 32 pins has been implemented to make the driver
function.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure. This driver uses fixups to define a common name
based on the SOC; until aliases for the new properties are added the
code assumes all pins are supported.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a config structure for each port and use the devicetree GPIO pin
count to initialize it. Simplify device initialization by using
instance number as only variation point.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the common data structure with the common config structure as
a prefix of the driver-specific config structure and use the
devicetree GPIO pin counts to initialize it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Extend the driver data structure with a field that identifies the pins
supported by the device. Document the fields and who is responsible
for maintaining them.
Update all configuration functions for specific pins to return an
error if the pin is not supported.
Update all set/get functions for specific pins to assert if the pin is
not supported.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since this was converted to the setup/handle/process idiom in master
the conversion is straightforward.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit updates the HMC5883L driver to use the new GPIO API.
Also add a note explicitly describing the active state of the DRDY
pin in the binding file.
Tested on frdm_k64f.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Update sample overlay for missing chip select and to deconflict with
UART TXD. Add GPIO flags to configuration state. Replace callback
enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a sample overlay. Add GPIO flags to configuration state. Replace
callback enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Put all the devicetree configuration data into a config structure in
flash, which removes some ultra-long identifiers from the code and
makes it more readable, and prepares for multiple instance support.
Consistently use the interrupt signal datasheet name for all objects
that are specific to that signal, including configuration structure
tags and function names.
Update the trigger idiom for setup/handle/process stages.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Converts the fxas21002 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on the hexiwear_k64 board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This breaks down the GPIO controller definition in DTS into
multiple entries. This allows these controllers to be
referenced by other DTS, and test board overlay files.
And also we can remove the entries in the dts fixup file.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update driver code to use new GPIO configuration flags such as
GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update bluetooth hcp spi driver to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Get reset, irq and cs flags from dt defines
- Define reset pin as active low and invert set/unset logic.
Tested on disco_l475_iot1 and 96b_carbon.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The public API for GPIO flags should use unsigned values, and for
MISRA compliance the size should not be platform-dependent. Add a
typedef for generic flags.
Also add typedefs for pin indexes and devicetree flags so these can
be safely recorded from devicetree property values without risking
loss of information if more flags are added in the future.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commits adds GPIO driver for LiteX SoC builder.
Due to the fact that GPIO in LiteX is unidirectional and can be
configured with different pins amount per port, additional entries
were added to the dts file.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
IO extenders may provide input signals to LEDs or sensors where
leaving the signal undriven may result in increased power consumption
or misbehavior. The SX1509B powers up with all signals configured as
inputs. Provide a way to indicate which pins should be set as output,
and their initial signal level, when the device is configured.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update ALERT active level in all devicetree files. Capture GPIO flags
in static configuration. Add internal API to enable and disable
interrupt, to release the handlers when an alert occurs, and to
re-enable the signal when the handler completes. Check for alerts
received during periods when the interrupt was disabled.
Extend the example to handle both above and below range triggers and
alerts that are present on startup.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The cached state of the output must be managed under mutex, but the
original toggle implementation read the current state outside the
mutex and used it to update the state. Rework the internal API so
that toggle is done within the mutex, distinct from masked set.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert the GPIO based driver to the new GPIO API. (Only the
gpio_configure() call is affected).
Move configuration to DT where appropriate for both SPI and GPIO
drivers, only leaving the SPI vs. GPIO decision in Kconfig (in
addition to the basic enable for the driver.) Move some files around
to clean up as a result of this change.
led_ws2812 sample changes:
- make the pattern easier to look at by emitting less light
- use led_strip alias from DT to get strip device, allocate
appropriate struct led_rgb buffer, etc.
- move the pins around and remove 96b_carbon support (I have no board
to test with)
GPIO driver specific changes:
- str is required to write OUTSET/OUTCLR, not strb. The registers
are word-sized.
- the str[b] registers must all be in r0-r7, so "l" is the correct GCC
inline assembly constraint for both "base" and "pin"
SPI driver specific changes:
- match the GPIO driver in not supporting the update_channels API
method, which never made sense for this type of strip
- return -ENOMEM when the user tries to send more pixel data
than we have buffer space for instead of -EINVAL
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Mark the INT signal to be active low and use the new functions to get
gpio state and configure the gpio interrupt flanks.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
This factors the common bits of device declaration into macros
so it would be easier to add new instances.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove support for GPIO_ACCESS_BY_PORT in the config function
as configuration by port is going away.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Since the GPIO expander is a I2C device, any read/write to
the registers has high latency. Therefore, semaphore is
introduced to prevent multiple threads to manipulate
the GPIOs at the same time.
Also make sure that we are not doing I2C transactions
within ISRs.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Only update the internal register cache after successful write,
or else it would get out of sync with hardware.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The register pair for each port in the GPIO expander are
port 0 first then port 1. This would not work for big
endian systems with the u16_t port value. So need to
swap the byte ordering on such system.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The structures defined in the header file are only used by
the driver source file, and should not be used by others.
So roll the header file into the source file so it won't
get #include.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use I2C burst write to write 2 bytes to each pair of registers
instead of 2 separate transactions of writing 1 byte.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
PCA95XX is a series of compatible I2C-based GPIO expanders,
with common registers on input/output, polarity and configuration.
This renames the original PCAL9535A driver to PCA95XX to indicate
that it can support this series. Additional features on variants
are guarded by kconfigs.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The interrupt functionality of this driver is incomplete,
but for the sake of not slowing down the GPIO API refactor,
I'm just returning -ENOTSUP until we can track down the issue.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
The 1pin test fails to pass because it expects to be able to
manipulate more than 16 pins. Since the intent is to filter invalid
pins at the wrapper level remove the validation performed within the
driver.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Some drivers masked the set of signaled pins based on enabled
interrupts, some did not. For those that did not the 2-pin test could
fail. The documentation does not imply that pins unrelated to the
callback participate in the notification process, so do the filtering
in the generic callback loop.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
In order to reliably detect interrupts the interrupt must be
acknowledged before the callback is invoked.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
In the fine print of the manual it's stated that attempts to enable a
pull in one direction while the pull in the other direction is enabled
are ignored. This has been confirmed. Change logic to disable both
pulls, then enable the one that's configured, if any.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
In order to reliably detect interrupts the interrupt must be
acknowledged before the callback is invoked.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Correct DRDY active level to default active-high, switch to new
interrupt configuration.
Also fix a common bug where an already-active DRDY signal is not
properly handled.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Updates gpio driver and device tree files to the new GPIO Config flags
- Implements the new port_* APIs
- Update I2C and PWM Drivers to use new GPIO config
- Add esp32.overlay to gpio_basic_api test
- refactor convert_int_type, regs struct
- remove config_polarity
- add kConfig notes
Tests:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_basic_api
- tests/drivers/gpio/gpio_api_1pin
Board:
- esp32 DevKitC V4
Note about interrupts:
The ESP32 requires specifying a CPU interrupt to be used for GPIO
interrupt signals. CPU interrupts can be either level or edge (or
special) triggered, but not both.
Please check gpio/Kconfig.esp32 for more info.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
As the mmio32 is more of a library than a proper driver, just implement
the new port functions and have pin_interrupt_configure marked pretty
much as not supported.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Updates the rv32m1 gpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Stops quietly reconfiguring pinmuxes to gpio mode. The pinmux must now
be configured explicitly in the board's pinmux.c or in the application.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
On boards:
- rv32m1_vega_ri5cy
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Remove redundant interrupt code from gpio_mcux_configure, move the rest
to gpio_mcux_pin_interrupt_configure.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
We treat GPIO_INT_MODE_LEVEL as not supported as the hardware doesn't
seem to handle level interrupts as one would expect. Looking into this
further to determine if its a HW bug or some misconfiguration in the
software.
We don't support dynamic setting of PULL_UP/PULL_DOWN config as this is
handled by pinctrl for the current boards we support the CMSDK AHB
driver on.
Tested on musca-a board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
LPC GPIO architecture uses multiple devices.
GPIO input is routed via INPUTMUX to the PINT
device which roots the interrupt to NVIC.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Updates the mcux lpc driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle functions recently added to the gpio api.
ISR functions to be added later.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
stm32_exti_enable was returning errors on line > 32 or line pointing
to non implemented line. Both conditions are hard-coded, hence there
is no use to detect them dynamically in the code.
Check them with assert. As a consequence, function could now be void.
Additionally, enable exti irq line only if both checks are passed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since it is now possible to disable/re-enable interrupts and
also to reconfigure an already configured interrupt, it is
now required to clear non requested triggers.
While it is not strictly requested, triggers are also cleared
when interrupt is disabled (assuming trigger should be configured
when interrupt is enabled).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
fixup exti
Perform few clean up in stm32 gpio driver:
*Clean up uint32_t occurrences left over.
*Move function gpio_stm32_flags_to_conf from const to static
and remove useless parameter check
*Rework error handling in functoin gpio_stm32_config
*Remove gpio_stm32_int_enabled_port function and have direct call
to gpio_stm32_get_exti_source
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Updates the imx gpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
- tests/drivers/gpio/gpio_basic_api
On boards:
- udoo_neo_full_m4
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Updates the mcux igpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Removes port configuration support since that feature is deprecated in
the new gpio api.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
On boards:
- mimxrt1015_evk
- mimxrt1020_evk
- mimxrt1050_evk
- mimxrt1060_evk
- mimxrt1064_evk
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Implement the new GPIO driver APIs for the HT16K33 and update the
driver to use the new GPIO flags.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
On the TI CC32xx, the GPIO peripheral supports only 8 pins per port.
We should add assertions where appropriate to verify this.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Updates the cc13x2/cc26x2 gpio driver and all associated boards to use
new device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Tested with:
samples/basic/blinky
samples/basic/button
tests/drivers/gpio/gpio_api_1pin
tests/drivers/gpio/gpio_basic_api
On board:
cc1352r1_launchxl
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Updates the cc32xx gpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Tested with:
samples/basic/blinky
samples/basic/button
tests/drivers/gpio/gpio_api_1pin
tests/drivers/gpio/gpio_basic_api
On boards:
cc3220sf_launchxl
cc3235sf_launchxl
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API.
Tested on external SX1509B breakout board and Thingy:52.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
The interrupt triggering on both edges is a remnant from the old
Quark SE which has a customized DesignWare GPIO block. So remove
the support for both edges as the board is no longer supported.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The MCUX GPIO peripheral must be configured as either input or output.
Reject attempts to configure disconnected or bidirectional.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove handling for GPIO_INT_LEVELS_LOGICAL in driver now that we do
that in gpio_pin_interrupt_configure and gpio_pin_configure.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove handling for GPIO_INT_LEVELS_LOGICAL in driver now that we do
that in gpio_pin_interrupt_configure and gpio_pin_configure.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove handling for GPIO_INT_LEVELS_LOGICAL in driver now that we do
that in gpio_pin_interrupt_configure and gpio_pin_configure.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove handling for GPIO_INT_LEVELS_LOGICAL in driver now that we do
that in gpio_pin_interrupt_configure and gpio_pin_configure.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change when we clear interrupt status to happen before we handle the
callbacks. As the callbacks might manipluate the GPIO state and cause
a GPIO interrupt. If we clear interrupt status after than we might
miss an interrupt.
Also only clear interrupts for interrupts that are we have enabled and
that were reported when we read from the interrupt status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on frdm_k64f board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on nrf52840_pca10056 board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on sam_e70_xplained board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on efr32_slwstk6061a board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Both pin sets and values encoding pin values are ultimately represented
by 32-bit unsigned integers. Provide typedefs that make the role of a
parameter explicit.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit moves interrupt configuration for a single pin from
gpio_pin_configure to gpio_pin_interrupt_configure function.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit adds following functions which work with pin logical levels
(take into account GPIO_ACTIVE_LOW flag):
- gpio_port_get, gpio_port_set_masked, gpio_port_set_bits,
gpio_port_clear_bits, gpio_port_set_clr_bits
- gpio_pin_get, gpio_pin_set
Functions which work with pin physical levels:
- gpio_port_get_raw, gpio_port_set_masked_raw, gpio_port_set_bits_raw,
gpio_port_clear_bits_raw, gpio_port_set_clr_bits_raw
- gpio_pin_get_raw, gpio_pin_set_raw
As well as functions:
- gpio_port_toggle_bits, gpio_pin_toggle_bits
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
When building the i2s tests on 96b_argonkey we get the following
warnings:
drivers/dma/dma_stm32.c: In function 'dma_stm32_configure':
drivers/dma/dma_stm32.c:181:2: error: 'periph_addr_adj' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
181 | switch (increment) {
| ^~~~~~
drivers/dma/dma_stm32.c:161:2: error: 'memory_addr_adj' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
161 | switch (increment) {
| ^~~~~~
Fix by initialzing periph_addr_adj and memory_addr_adj to 0.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The current sam spi driver uses soc dependent name which duplicate
configuration to enable other platforms. This refactor current
definitions to a generic way to reuse symbols by multi soc definitions.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
spi_context_lock() & spi_context_release() are called in transceive()
function for a better readability.
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
riscv64 CPUs can access full 64-bit memory-mapped register by a single
instruction, so we can directly access these registers.
Signed-off-by: Jim Shu <cwshu@andestech.com>
Watchdog type is found on e.g. Pearl/Jade Gecko, often
more than 1 is present.
Driver supports timeout and (minimum) window configuration
and reset or timeout interrupt support for now.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Gain values are specified with enumeration values that can't be used
to reverse the effects of scaling the input signal. Provide a
function that reverses the effect of the gain by scaling a measured
value.
Also provide a function that converts a raw measurement captured with
a reference voltage and specific gain and resolution to the
corresponding voltage in millivolts.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Introduces a new ft5336 touch panel driver for the keyboard scan (kscan)
interface. The driver currently uses a timer to periodically poll touch
data in the system work queue, but later it can be enhanced to use a
gpio interrupt instead of a timer.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
ARM cores may have a per-core architected timer, which provides per-cpu
timers, attached to a GIC to deliver its per-processor interrupts via
PPIs. This is the most common case supported by QEMU in the virt
platform.
This patch introduces support for this timer abstracting the way the
timer registers are actually accessed. This is needed because different
architectures (for example ARMv7-R vs ARMv8-A) use different registers
and even the same architecture (ARMv8-A) can actually use different
timers (ELx physical timers vs ELx virtual timers).
So we introduce the common driver here but the actual SoC / architecture
/ board must provide the three helpers (arm_arch_timer_set_compare(),
arm_arch_timer_toggle(), arm_arch_timer_count()) using an header file
imported through the arch/cpu.h header file.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Lot of misdefined variables that went in undetected due to lack of CI on
this board. Fix them and test build with new SDK.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Switch to `NET_SOCKET_REGISTER` mechanism over the offloaded API
registration.
Including the following fixes from the review:
* The fd returned by the socket accept call needs to be finalized,
similar to how it is done for socket creation.
* sl_RecvFrom() in TI SimpleLink Host driver does not support NULL
pointers for 'from' address and address length, and sl_SendTo() does
not ignore the destination address when in connection mode, so passing
NULL would cause a failure. These issues have been reported to TI
(CC3X20SDK-1970, CC3X20SDK-1971).
Let's use sl_Recv and sl_Send to implement recvfrom/sendto in the case
of NULL addresses.
* simplelink_poll() should not process negative file descriptors in the
fds array after sl_Selecti() returns. A negative fd value indicates
that the entry is invalid and should be ignored.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Used the SocketCAN initalization code from the can_stm32.c driver which
successfully initializes SocketCAN for the Flexcan driver
Signed-off-by: Peter van der Perk <peter.vanderperk@nxp.com>
If the Ethernet driver has VLAN enabled (only native_posix, mcux
or gmac has VLAN supported), then the iface pointer in ethernet
context should contain the main network interface. This is needed
so that the interface will get link address set to it properly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Current implementation directly passes timeout value to workqueue/timer
which results in assertion or instant timeout in case when K_FOREVER is
passed. This fix ensures that no timer or workqueue is called with
K_FOREVER.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Use signed values for timeout in UART asynchronous API, to be consistent
with timeout type in timer and workqueue values.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Extended nrf_uarte driver to support TX only UARTE instances.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Added delay before starting low frequency clock for the first time to
ensure that anomaly conditions are not met. Delay is configurable and
might be disabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Most JEDEC NOR flash devices uses not only typical SPI mode
(MISO,MOSI,SCK and CS), but also QSPI mode (IO0,IO1,IO2,IO3,SCK and CS).
QSPI mode uses more data lines and as a result provide higher
throughput. If this were not enough, Nordic chips provide
hardware acceleration for read/write/erase functions, what
gives significant performance boost.
It does a lot of things "behind the scene", i.e when user has written
some data to the flash and would like to read them back, it has to wait
until the flash is ready by reading WIP bit in Status Register.
This driver does it automatically.
Signed-off-by: Kamil Lazowski <Kamil.Lazowski@nordicsemi.no>
Update the hal_nordic module revision, to switch to nrfx 2.1.0.
Because the list of peripherals for nRF5340 has changed as follows:
- SPIM2 has been renamed to SPIM4
- SPIM2-3, SPIS2-3, TWIM2-3, TWIS2-3, and UARTE2-3 have been added
a couple of related corrections needed to be applied in dts and Kconfig
files, plus the spi_nrfx_spim driver has been extended with the support
for SPIM4.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The rf2xx driver is doing automatic retransmissions in hardware based
on whether ACKs are received or not. Currently the driver is not
invoking ieee802154_radio_handle_ack() as other drivers are doing and
required by OpenThread since 4fe1da9. This add rf2xx_handle_ack method
to ensures required ACK processing when driver performs TX.
Fixes: #21763
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Lots of style mess in this driver:
- 80 chars limit not followed
- variable allocation and if condition on it should be coalesced
- etc...
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
DesignWare driver can manage different amount of irqs so let's make it
configurable via DTS.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Base address does not change at runtime, thus storing it directly into
device's config.
Also keeping it consistent in naming: s/port/dev
And no need to store irq_num as it is unused.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There will be more instance of that driver, and the initialization
function will the same all the time. That was done wrong as it was not
following the device driver rules.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This driver is going to be used by other SoCs and as such should be
easily configurable through DTS.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
irq_enable() can be directly called from relevant irq config function
and thus voids the necessity to store the IRQ number, saving some
memory.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There is no such thing as CAVS DMA IP block, the DMA IP block found on
CAVS based chips is made with DesignWare one.
This will help to centralize DW based DMA device into one driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The sx1276_rx_done() function supports RSSI and SNR.
Change to support RSSI and SNR through sx1276_lora_recv() function.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
The RF2XX driver not always sent ACK when a RX frame requests. This
happen because RF2XX transceiver asserts TRX_END interrupt after
confirm that the FCS is valid. The driver can now decode the frame
but in parallel the radio still processing the ACK frame. This will
sync the radio FSM state to ensure that ACK will be send.
Fixes#21659
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Remove soc/arm/st_stm32/stm32YY/flash_registers.h files.
Change register accesses in stm32 flash drivers to use FLASH_TypeDef
from modules/hal/stm32/stm32cube/stm32YYxx/soc/stm32xxxxxx.h.
Fixes#16235
Signed-off-by: Sarvesh Patkar <psarvesh314@gmail.com>
usb-device.h must be included only if CONFIG_USB_UART_CONSOLE is
defined, otherwise it is not used and will pull a lot of usb code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
when DMA IP is enabled on stm32 series,
the heap size must be configured to large value
because of dma channels configuration.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patches defines constants from dma registers
depending on the dma configuration of the stm32 soc
Some devices have 6 or 7 or 8 dma channels per dma instance
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This checks if the DMA controller supports or not
the memory-to-memory transfers. For DMA Version1,
in the stm32f2xx, stm32f4xx, stm32f7xx series,
only DMA instance 2 is able to transfer mem-to-mem.
For other series, with DMA Version2, there is no such a limitation.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fix#22188
Introduce config option to disable automatic acknowledge via
virtual wires on response to eSPI host suspend and reset warnings.
This will give the opportunity for eSPI slave systems that need to
perform preparations before reset or suspend.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Introduce a new counter API function for reading the current counter
value (counter_get_value()) and deprecate the former counter_read() in
favor of this.
Update all drivers and calling code to match the new counter API.
The previous counter driver API function for reading the current value
of the counter (counter_read()) did not support indicating whether the
read suceeded. This is fine for counters internal to the SoC where the
read always succeeds but insufficient for external counters (e.g. I2C
or SPI slaves).
Fixes#21846.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
So far, nRF 802.15.4 radio driver build was dependent on the 802.15.4
subsystem in Zephyr. While this was a reasonable approach for samples,
it prevented the radio driver from being built as a standalone entity,
which could be useful in some applications (e. g. running core nRF
802.15.4 radio driver tests with Zephyr).
Resolve this, by providing a separate set of Kconfigs for the radio
driver, therefore allowing to build it as a separate entity. The 802154
subsystem simply enables the radio driver module in this case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Implement uart_pipe functionality for the modem so that it
integrates with the PPP implementation.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Create a driver for GSM modems that use a standard AT command set
and enable Zephyr's own PPP stack for IP traffic.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
This commit introduces the can-primary alias to identify
the primary CAN interface.
This alias is used for all samples and tests, so they don't
need to probe the right interface.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The CONFIG_ prefixes were missing on these.
Found with a work-in-progress scripts/kconfig/lint.py check.
This symbol is defined in kernel/Kconfig.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
