Changing more of DT_* prefixed macros that refer to instances to use
DT_INST macros in GPIO, I2C and UART drivers.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Several macros were documented as deprecated but lacked the
infrastructure to produce deprecation warnings. Add the deprecation
marker, and fix the in-tree references to the deprecated spellings.
Note that one non-deprecated macro should have been deprecated, and
is, referring to a newly added line control bit.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The uart_cc32xx driver used system clock frequency
as a base for baudrate calculation. This commit corrects
that by obtaining the needed value from DTS.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
poll_out function was returning the character that was sent. It
happens that it is always constant and the return of this functions is
never tested. Changing it to be a void function.
MISRA-C rule 17.7
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The Zephyr console and shell interrupt processing assumes
a TX interrupt is evoked upon first enabling the TX
interrupt via uart_irq_tx_enable.
This was not the case with the cc32xx uart, coming out of
reset, with FIFO's disabled.
The only way found to achieve this behavior is to fill
the fifo with a non-printable character on initialization.
Also, the uart driver was explicitly clearing TX/RX interrupts in
its isr, which was unnecessary, as the act of reading/writing
did that implicitly.
These fixes allow the cc32xx uart to work with the
current Zephyr console/shell design.
Fixes: #11202
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update a couple of labels generated from DTS used directly (not through
dts_fixups) in some serial drivers, to the reflect recent changes made
to the extracting script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Zephyr UART drivers offer very low-level functionality. Oftentimes,
it would be useful to provide higher-level wrappers around UART
device which would offer additional functionality. However, UART
driver irq callback routine receives just a pointer to (low-level)
UART device, and it's not possible to get to a wrapper structure
(without introducing expensive external mapping structures). This
is an indirect reason why the current UARt wrappers - uart_pipe,
console - are instantiated statically just for one underlying UART
device and cannot be reused for multiple devices.
Solve this by allowing to pass an arbitrary user data to irq
callback, set by new uart_irq_callback_user_data_set() function.
Existing uart_irq_callback_set() keeps setting a callback which
will receive pointer to the device.
While public API maintains compatibility, drivers themselves need
to be updated to support arbitrary user data storage/passing (as
legacy uart_irq_callback_set() functionality is now implemented in
terms of it).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the TI CC32xx UART out of the device
tree instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
uart_irq_tx_empty() function proved to be problematic: its semantics
was not documented properly, and many hardware uses terminology like
"TX register empty" to signify condition of TX register being ready
to accept another character (what in Zephyr is tested with
uart_irq_tx_ready()). To avoid confusion, uart_irq_tx_empty() was
renamed to uart_irq_tx_complete(), propagating to drivers/serial
device methods.
The semantics and usage model of all of uart_irq_rx_ready(),
uart_irq_tx_ready(), uart_irq_tx_complete() is now described in
detail.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Devicetree.org specifies that serial devices property used to set
baud rate is "current-speed", while zephyr uses "baud-rate".
Align property name in order to keep zephyr dts files compatible
with device tree specification and could be re-used from/to
Linux for instance. We also cleanup a few SoCs that set "baud-rate" in
the SoC dts and not the board.
Jira: ZEP-2048
Change-Id: I097e7439ee46fe77c628b56531772950382fafcc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As part of the transition to Device Tree, a temporary
HAS_DTS configuration variable, and a .fixup file per board
with symbol aliases were added.
This patch removes the cc32xx related fixup file
definitions, except for those used additionally outside
the cc32xx drivers.
Since cc32xx has DTS files, and since HAS_DTS will always be true,
it also removes the 'if !HAS_DTS' blocks from the cc32xx Kconfig
files.
Change-Id: I1c1b9f734795f523342f82ab32f2a38983812c0b
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Previously, cc3200_launchxl board was not able to show the
Zephyr Boot Banner, as that required early initialization
of the UART driver, which was done POST_KERNEL.
This patch moves the pinmux and UART driver initialization
to PRE_KERNEL_1, allowing early printk, and the Boot Banner
to show.
Change-Id: I84a7c20c1d5bdc3de150dc6bb0adebc9a2d9f5cb
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
This patch ifdef's out information that would be redefined by
information generated from DTS. This patch also fixes up the serial
drives to work properly with the DTS generated information.
Change-Id: I912ccf35be23c107705a4866e5a68b3b51154ffa
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit replaces the nanokernel.h include by kernel.h.
Change-Id: Ib42fbf2d9f77a73c0831f569b3dbbfb342ea2e1d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/hello_world
- samples/philosophers
- samples/drivers/uart
- samples/shell
UARTA0 is currently supported.
Change-Id: I85727c622d4d42183cc9f2f8b43d653e245dd17e
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
