Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This trivial patch extends the PCIe shell to check for and report
on a device's ability to use MSI-X interrupt signaling.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Per guidelines, all statements should have braces around them. We do not
have a CI check for this, so a few went in unnoticed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some firmwares (looking at you, slimbootloader) don't set the registers
in PCI configuration space to indicate the IRQ routing, so we remove
the check that verifies that the user and firmware agree on IRQ number.
Also eliminate the return value of pcie_irq_enable() since no one uses
it and we can't return a meaningful value any longer.
Signed-off-by: Charles Youse <charles.youse@intel.com>
Firmware is supposed to set a register in PCI configuration space which
indicates the hardware IRQ that the endpoint is attached to.
A function is implemented which reads this register, and the PCIe shell
is updated to use it instead of doing it "manually".
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
A new function pcie_irq_enable() is added to be used in lieu of
irq_enable() when the target device is PCI(e)-attached. The function
attempts to use MSI, when configured in the kernel and supported by
the endpoint; failing that, it will verify that IRQ requested is in
fact routed to the device by the boot firmware before enabling it.
The NS16550 UART driver is updated to use pcie_irq_enable().
The PCI(e) shell is extended to dump information about wired IRQs.
The up_squared devicetree is fixed (reverted?) to IRQ5 for UART1.
The galileo enables MSI by default.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
A parallel PCI implementation ("pcie") is added with features for PCIe.
In particular, message-signaled interrupts (MSI) are supported, which
are essential to the use of any non-trivial PCIe device.
The NS16550 UART driver is modified to use pcie.
pcie is a complete replacement for the old PCI support ("pci"). It is
smaller, by an order of magnitude, and cleaner. Both pci and pcie can
(and do) coexist in the same builds, but the intent is to rework any
existing drivers that depend on pci and ultimately remove pci entirely.
This patch is large, but things in mirror are smaller than they appear.
Most of the modified files are configuration-related, and are changed
only slightly to accommodate the modified UART driver.
Deficiencies:
64-bit support is minimal. The code works fine with 64-bit capable
devices, but will not cooperate with MMIO regions (or MSI targets) that
have high bits set. This is not needed on any current boards, and is
unlikely to be needed in the future. Only superficial changes would
be required if we change our minds.
The method specifying PCI endpoints in devicetree is somewhat kludgey.
The "right" way would be to hang PCI devices off a topological tree;
while this would be more aesthetically pleasing, I don't think it's
worth the effort, given our non-standard use of devicetree.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
