All GPIO controller drivers support DTS so we can select HAS_DTS_GPIO
at the GPIO driver subsystem level rather than for each specific driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commits adds GPIO driver for LiteX SoC builder.
Due to the fact that GPIO in LiteX is unidirectional and can be
configured with different pins amount per port, additional entries
were added to the dts file.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
PCA95XX is a series of compatible I2C-based GPIO expanders,
with common registers on input/output, polarity and configuration.
This renames the original PCAL9535A driver to PCA95XX to indicate
that it can support this series. Additional features on variants
are guarded by kconfigs.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The SoC, driver, and board support for the CC2650 and CC2650 Sensortag
aren't currently supported and we are removing them as such. If anyone
is interesting in supporting this platform we can easily recovery it
from git.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add driver for the Texas Instruments LMP90xxx series of multi-channel,
low-power 16-/24-bit sensor analog frontends (AFEs).
The functionality is split into two drivers; an ADC driver and a GPIO
driver.
Tested with LMP90080 and LMP90100.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The gpio_atmel_sam3 is no longer required since the gpio_sam, common
SAM family GPIO driver, provides improved functionality.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Adds a new xec gpio driver that can be used with the
XEC MCUs. This driver modifies the PCR1 register in order
to configure gpio settings. Interrupts are triggered by the EC
interrupt aggregator block.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
The HT16K33 is a memory mapping, multifunction LED controller
driver. The controller supports up to 128 LEDs (up to 16 rows and 8
commons) and matrix key scan circuit of up to 13x3 keys.
This commit adds support for the keyscan functionality of the HT16K33.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
This board is unmaintained and unsupported. It is not known to work and
has lots of conditional code across the tree that makes code
unmaintainable.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
* Add support for gpio controller driver
Signed-off-by: Ashokkumar B <ashokkumar@zilogic.com>
Signed-off-by: Subash G <subash@zilogic.com>
Signed-off-by: Vishnu K <vishnu@zilogic.com>
Signed-off-by: Vaishnavi D <vaishnavi.d@zilogic.com>
Provide basic commands for configuring/setting/reading GPIO ports.
> gpio conf ..
> gpio set ..
> gpio get ..
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename log level variable:
CONFIG_LOG_GPIO_LEVEL to CONFIG_GPIO_LOG_LEVEL
Use template for log levels.
Register modules in drivers using logging.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
After GPIO shim using NRFX has been implemented, old gpio_nrf5
shim is no longer needed.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
FE310 is the name of one SoC out of a range of products in the SiFive
Freedom line. The FE310 SoC port in Zephyr is compatible with all of
these products, so rename the SoC to SiFive Freedom
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Piggyback a missing 'source "drivers/gpio/Kconfig.imx"'. This file
wasn't included anywhere previously.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adds a driver for SX1509B I2C GPIO chip. This driver only supports the
basic GPIO features and does not currently implement the LED driver and
keypad matrix features.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Add gpio mcux driver which can be used for lpcxpresso54114 and other lpc
socs. In this driver, CMSIS register access is made for GPIO.
Option for access by GPIO Pin is provided as of now.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The PIO cores on Altera Nios-II processors can be used
for GPIOs and each PIO core can be configured as Input only,
Output only or as Bidirectional port from the Qsys tool.
The present Nios-II softcpu image on the Zephyr only has the
support for Output only port and the PIOs[0:3] are wired to
LED[0:3] on the Altera MAX10 board.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Adds a new gpio driver for the NXP i.MX family of SoCs. Read, write,
configure, and callback API functions are all implemented.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This provides basic GPIO support, with interrupts, and the ability to
read and write to ports on a pin-by-pin basis.
Jira: ZEP-2286
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
It is envisaged that this will be used by SoC or board code to make
available fixed purpose memory-mapped i/o registers to the rest of the
system which normally expects to use GPIO devices, e.g. for driving chip
select lines, LEDs or reading button states.
As such, the driver code doesn't provide a kconfig based configuration
mechanism, instead SoC/board code can hard-wire the devices it wants
with something simple like:
GPIO_MMIO32_INIT(misc_reg1, "MISC1", 0x12345678, 0xffffffffu)
Then, for example, if bit N of the register at 0x12345678 is wired up as
an SPI device chip select line, the SPI driver could be configured to
use pin N of the "MISC1" GPIO driver and not need any other board
specific code.
Change-Id: Ib02fcbab73fcf9637e25834db060fb3108626f47
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
tested with blinky, button and disco apps
Change-Id: I4b520d4f3e42c97e4a723747ce4a6c67ca9f1d18
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
Now that we have a more generic mcux gpio driver that can be used across
multiple Kinetis SoCs, remove the specific k64 gpio driver.
Jira: ZEP-1394
Change-Id: I177f96a75e441b70c523e74e99f1b7a54eac6b0e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new mcux gpio driver that can be used for k64 and other Kinetis
SoCs. This driver uses mcux CMSIS register accesses to the GPIO and PORT
modules. Some of the logic from the k64 gpio driver was reused and
refactored (mainly flag parsing and callback handling).
Jira: ZEP-1394
Change-Id: If5e9390861c181ec555dce6569b14debb729526a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/basic/blinky
- samples/basic/disco
- samples/basic/button
All 4 GPIO ports are supported.
Change-Id: If8599a23c1d56cfd678a6e2e5339f7e093c6061a
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The driver is currently used only by the ARM Beetle platform.
Jira: ZEP-1245
Change-Id: I6611edd7486a3c6d82d66a9a96c5d4860dad1539
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
It's unused anywhere and unlikely to be in the future.
Change-Id: I57926e91da7d31ef6ddda4f86e6dac103dbfa176
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
No need to create new Kconfig that do exactly the same, just
reuse those from the main QMSI driver.
Change-Id: I965055f36845ac0464e4a383b0d05c3ae35c0015
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
GPIO drivers are now using new system log macros also updated the
Kconfig variable to be a level rather than a bool.
JIRA: ZEP-311
Change-Id: I9a49626d816080cb8081c2dd445bae31f5dbf409
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>