Add the following application-facing memory domain APIs:
k_mem_domain_init() - to initialize a memory domain
k_mem_domain_destroy() - to destroy a memory domain
k_mem_domain_add_partition() - to add a partition into a domain
k_mem_domain_remove_partition() - to remove a partition from a domain
k_mem_domain_add_thread() - to add a thread into a domain
k_mem_domain_remove_thread() - to remove a thread from a domain
A memory domain would contain some number of memory partitions.
A memory partition is a memory region (might be RAM, peripheral
registers, flash...) with specific attributes (access permission,
e.g. privileged read/write, unprivileged read-only, execute never...).
Memory partitions would be defined by set of MPU regions or MMU tables
underneath.
A thread could only belong to a single memory domain any point in time
but a memory domain could contain multiple threads.
Threads in the same memory domain would have the same access permission
to the memory partitions belong to the memory domain.
The memory domain APIs are used by unprivileged threads to share data
to the threads in the same memory and protect sensitive data from
threads outside their domain. It is not only for improving the security
but also useful for debugging (unexpected access would cause exception).
Jira: ZEP-2281
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
SoCs outside the Kinetis family can have the TRNG module, so move the
HAS_TRNG config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the RNGA module, so move the
HAS_RNGA config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the FTM module, so move the
HAS_FTM config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Note that 'select HAS_FTM' was previously missing from Kconfig.soc and
is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the ADC16 module, so move the
HAS_ADC16 config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the LPSCI module, so move the
HAS_LPSCI config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the LPUART module, so move the
HAS_LPUART config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
mcuboot_constraints.h had FLASH information related to the SoC that
should be maintained as part of the SoC and not in the subsystem. Also
fixed Makefiles to check for IMG_UTIL Kconfig and not MCUBOOT.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
stm32f417xe and stm32f417xg have been introduced with 2
different defconfig files. Since same code is declared
in both files, mutualize declarations in a single file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The enumerations stm32{f3,f4}x_pin_config_mode aren't used any
more. This patch removes them.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
In various places, a private _thread_entry_t, or the full prototype
were being used. Be consistent and use the same typedef everywhere.
Signen-off-by: Andrew Boie <andrew.p.boie@intel.com>
Indenting preprocessor directives reduces the code readability, because
it make preprocessor directives harder to spot.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add flash page layout support for STM32F4 SoCs.
This almost eliminates the need for flash_map.h, except for
STM32F4X_SECTOR_MASK, so delete the file and move the define into the
F4 implementation, to keep things simple.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Previously, this was only done if an essential thread self-exited,
and was a runtime check that generated a kernel panic.
Now if any thread has k_thread_abort() called on it, and that thread
is essential to the system operation, this check is made. It is now
an assertion.
_NANO_ERR_INVALID_TASK_EXIT checks and printouts removed since this
is now an assertion.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In benchmark test (test_info) while making function call regs
r0 - r4 are modified into called function. Due to this value
inside r3 is getting lost.
This patch saves and restore the value in r0-r4 regs while making
function calls from assembly language.
Jira: ZEP-2314
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
The API/Variable names in timing_info looks very speicific to
platform (like systick etc), whereas these variabled are used
across platforms (nrf/arm/quark).
So this patch :-
1. changing API/Variable names to generic one.
2. Creating some of Macros whose implimentation is platform
depenent.
Jira: ZEP-2314
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
This patch fixes a couple of issues with the stack guard size and
properly constructs the STACK_ALIGN and STACK_ALIGN_SIZE definitions.
The ARM AAPCS requires that the stack pointers be 8 byte aligned. The
STACK_ALIGN_SIZE definition is meant to contain the stack pointer
alignment requirements. This is the required alignment at public API
boundaries (ie stack frames).
The STACK_ALIGN definition is the required alignment for the start
address for stack buffer storage. STACK_ALIGN is used to validate
the allocation sizes for stack buffers.
The MPU_GUARD_ALIGN_AND_SIZE definition is the minimum alignment and
size for the MPU. The minimum size and alignment just so happen to be
32 bytes for vanilla ARM MPU implementations.
When defining stack buffers, the stack guard alignment requirements
must be taken into consideration when allocating the stack memory.
The __align() must be filled in with either STACK_ALIGN_SIZE or the
align/size of the MPU stack guard. The align/size for the guard region
will be 0 when CONFIG_MPU_STACK_GUARD is not set, and 32 bytes when it
is.
The _ARCH_THREAD_STACK_XXXXXX APIs need to know the minimum alignment
requirements for the stack buffer memory and the stack guard size to
correctly allocate and reference the stack memory. This is reflected
in the macros with the use of the STACK_ALIGN definition and the
MPU_GUARD_ALIGN_AND_SIZE definition.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch removes the redundant stack alignment check being done. The
stack definition macros enforce the alignment requirements via the
__align() directives.
In addition, fix the rounding down of the psp to be correct. The
actual initial stack pointer is the end of the stack minus the size of
the __esf structure. Rounding down after the subtraction will get us
to the correct offset.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
When we mask out the GPIO High impedance/Pull-up/Pull-down field we
should be shifting the mask file, not shifting the field. This is
because all the other defines already assume the shift.
Coverity-CID: 173640
Jira: ZEP-2538
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Previously, calling NVIC_SetPriority(IRQn_Type irqn, ....) with
the NWP interrupt number of 171 caused a hard fault during a
subsequent svc #0 instruction during _Swap().
GNU compiler is generating a bit extension instruction (sxtb) which
converts a positive IRQ value argument to a negative value when
casting to the CMSIS IRQn_Type enum parameter type.
This generates a negative index, which then writes to an SCB
control register instead of NVIC register, causing a hard
fault later on.
This issue only occurs when passing interrupt numbers > 0x80
(eg: 171 (0xab) for the NWP) to the CMSIS NVIC apis.
The solution here is simply to redefine IRQn_Type to be an
unsigned 32 bit integer, while redefining the CMSIS IRQn_Type
enum definitions for interrupts less than zero.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
An abnormal crash was encountered in ARMv6-M SoCs that don't have flash
starting at 0. With Zephyr OS the reason for this crash is that, on
ARMv6-M the system requires an exception vector table at the 0 address.
We implement the relocate_vector_table function to move the vector table
code to address 0 on systems which don't have the start of code already
at 0.
[kumar.gala: reworderd commit message, tweaked how we check if we need
to copy vector table]
Signed-off-by: Xiaorui Hu <xiaorui.hu@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have an mcux shim driver, remove the old k64-specific
driver. Also remove include/drivers/k20_sim.h, since the old
k64-specific driver was the only thing left using it.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Switches the default pwm driver from the k64-specific driver to the
mcux shim, which can be used on other SoCs with the ftm peripheral.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux ftm driver to adapt it to the Zephyr
pwm interface.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adjusts the ARM MPU implementation to be compliant to the
recent changes that introduced the opaque kernel data types.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The mimimum mpu size is 32 bytes, but requires mpu base address to be
aligned on 32 bytes to work. Define architecture thread macro when
MPU_STACK_GUARD config to allocate stack with 32 more bytes.
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
In the stm32_gpio_flags_to_conf function the configuration
values of the GPIO pin are shifted two times. One in the
stm32-pinctrlf1 header and one in the function. This patch
removes one of those shifts.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This patch adds the allow flash write CONFIG option to the ARM MPU
configuration in privileged mode.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: David Brown <david.brown@linaro.org>
This patch adds the allow flash write CONFIG option to the NXP MPU
configuration in privileged mode.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: David Brown <david.brown@linaro.org>
Currently Thread time slice is getting reset at end of timer
interrupt. Due to which equal priority threads behind current thread
in ready_q are not getting chance to run and leading to starvation.
This patch handles time slice in _ExcExit section context switch is
required.
Jira: ZEP-2444
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The ouput speed of the gpio pins passed via the 'conf' argument was
ignored, causing the speed to always be in its reset state (lowest
possible speed for most pins). This was causing problems for pins that
actually need a speed faster than the default, like the ethernet
controller pins.
Combined with the correct pinmux configuration this fixes problems
of the olimex_stm32_e407 board not being able to send ethernet data.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Historically, stacks were just character buffers and could be treated
as such if the user wanted to look inside the stack data, and also
declared as an array of the desired stack size.
This is no longer the case. Certain architectures will create a memory
region much larger to account for MPU/MMU guard pages. Unfortunately,
the kernel interfaces treat both the declared stack, and the valid
stack buffer within it as the same char * data type, even though these
absolutely cannot be used interchangeably.
We introduce an opaque k_thread_stack_t which gets instantiated by
K_THREAD_STACK_DECLARE(), this is no longer treated by the compiler
as a character pointer, even though it really is.
To access the real stack buffer within, the result of
K_THREAD_STACK_BUFFER() can be used, which will return a char * type.
This should catch a bunch of programming mistakes at build time:
- Declaring a character array outside of K_THREAD_STACK_DECLARE() and
passing it to K_THREAD_CREATE
- Directly examining the stack created by K_THREAD_STACK_DECLARE()
which is not actually the memory desired and may trigger a CPU
exception
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Move to using the generated IRQ defines from the DTS instead of soc.h.
This change also fixes a minor bug in that the error irq priority wasn't
getting correctly picked up from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32F3 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32F4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rework stm32f1 pinmux code for future dts based pinmux code
generation.
Pin configuration is now done directly thanks to gpio port
configuration. Reference to pseudo alternate functions are
now removed same as the use of pins[] array.
Pins function (uart tx for instance) is set implicitly by
defining gpio mode and configuration.
This behavior is specific to stm32f10x series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32L4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed and information is transferred to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In L4 series, select HAS_STM32CUBE is done per soc.
This could be factorized in Kconfig.series.
Aim is to lower the steps to add a new SoC.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that we generate BLUETOOTH_UART_ON_DEV_NAME, UART_PIPE_ON_DEV_NAME,
and BLUETOOTH_MONITOR_ON_DEV_NAME Kconfig defines for dts enabled
platforms add those into the appropriate dts files and remove from the
various board/Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
With introduction of commit "pinmux: stm32: directly return error if
stm32_get_pin_config fails", pin configuration fails when
pins are not configured in pins[] array.
This was the case for configuration UART1 assigned on PB6/PB7.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
If the adc driver configuration is enabled (CONFIG_ADC=y), then enable
the mcux shim driver by default for all Kinetis SoCs.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux adc16 driver to adapt it to the Zephyr
adc interface.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add a STM32 LL based driver for the RNG processor. The RNG processor
is a random number generator, based on a continuous analog noise, that
provides a random 32-bit value to the host when read. The RNG passed
the FIPS PUB 140-2 (2001 October 10) tests with a success ratio of 99%.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enabled the boot_time test on ARM SoCs, set __start_time_stamp on ARM
since we don't have a free running counter similar to TSC on x86.
Also moved to printing the values out as %u to increase the range of
values.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In added mode flash operation are performed in timeslice
(in radio idle time).
Kconfig for mode enabling CONFIG_SOC_FLASH_NRF5_RADIO_SYNC.
Erase and write API implementations were rewritten and preserved against
concurrent execution.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Board port was done before the yaml transition, so was missing a
cc2650_sensortag.yaml. As such when we build all the test we get a few
build errors that we also fixed up.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add configuration, documentation, pinmux, fixup and dts support for
STM32F103x8 based Minimum System Development board.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Add configuration and memory definitions to support STM32F103x8
Medium-density performance line SoC with 64 KB Flash.
Merge multiple files into single Kconfig.defconfig.stm32f103xx
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Since not all socs from f3 series (i.e stm32f334x8 no MPU) have MPU
capability, add capability only for MPU capable socs in Kconfig.soc
JIRA: ZEP-2220
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
As other stm32 series support MPU, move common file in a file tree
useable by socs from other series
JIRA: ZEP-2220
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
We always have UART_IRQ_FLAGS set to 0, so just call IRQ_CONNECT with a
0 argument for the flags, and remove the UART_IRQ_FLAGS. This is
towards support for using the driver on the TI CC2650. (we add a
comment about that as well).
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clearing fields in the region descriptor attributes doesn't always have
the expected effect of revoking permissions. In the case of bus master
supervisor mode fields (MxSM), setting to zero actually enables read,
write, and execute access.
When we reworked handling of region descriptor 0, we inadvertently
enabled execution from RAM by clearing the MxSM fields and enabling the
descriptor. This caused samples/mpu_test run to throw a usage fault
instead of an MPU-triggered bus fault.
Fix this by setting all the MxSM fields to 2'b11, which gives supervisor
mode the same access as user mode.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Both the ARM and NXP MPU drivers incorrectly calculated the region index
by assuming the region type (e.g., THREAD_STACK_GUARD_REGION) was
zero-indexed, when in reality it is one-indexed. This had the effect of
wasting one region.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The NXP MPU requires special handling of region descriptor 0 to
guarantee that the debugger has access to the entire address space. It
does not allow writes from the core to affect the start or end
addresses, or the permissions associated with the debugger.
The original implementation of this driver attempted to work around
region descriptor 0, resulting in an off-by-1 error caught by Coverity.
Instead, define region descriptor 0 explicitly in the mpu_regions array,
and add some asserts to ensure that one doesn't try to change its start
or end addresses. This has an added benefit such that more permissions
can be enabled in region 0 if desired, whereas the previous
implementation always forced all writable permissions to be cleared.
Coverity-CID: 170473
Jira: ZEP-2258
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The original implementation of _get_num_regions() parsed the CESR[NRGD]
register field to determine the number of mpu region descriptors
implemented in hardware. There was a possible path in the code to return
zero, which would cause underflow later on in arm_core_mpu_configure().
Coverity complained despite an assert to catch this condition. Instead,
use a preprocessor macro from mcux that defines the number of mpu region
descriptors.
Coverity-CID: 169811
Jira: ZEP-2208
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Stack sentinel doesn't prevent corruption, it just notices when
it happens. Any memory could be in a bad state and it's more
appropriate to take the entire system down rather than just kill
the thread.
Fatal testcase will still work since it installs its own
_SysFatalErrorHandler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
One of the stack sentinel policies was to check the sentinel
any time a cooperative context switch is done (i.e, _Swap is
called).
This was done by adding a hook to _check_stack_sentinel in
every arch's __swap function.
This way is cleaner as we just have the hook in one inline
function rather than implemented in several different assembly
dialects.
The check upon interrupt is now made unconditionally rather
than checking if we are calling __swap, since the check now
is only called on cooperative _Swap(). The interrupt is always
serviced first.
Issue: ZEP-2244
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The REGION bits (bit[3:0]) of MPU_RBAR register can specify the number
of the region to update if the VALID bit (bit[4]) is also set.
If the bit[3:0] of "region_addr" are not zero, might cause to update
unexpected region. This could happen since we might not declare stack
memory with specific alignment.
This patch will mask the bit[4:0] of "region_addr" to prevent updating
unexpected region.
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
The kernel tracks time slice usage with the _time_slice_elapsed global.
Every time the timer interrupt goes off and the timer driver calls
_nano_sys_clock_tick_announce() with the elapsed time, this is added to
_time_slice_elapsed. If it exceeds the total time slice, the thread is
moved to the back of the queue for that priority level and
_time_slice_elapsed is reset to zero.
In a non-tickless kernel, this is the only time _time_slice_elapsed is
reset. If a thread uses up a partial time slice, and then cooperatively
switches to another thread, the next thread will inherit the remaining
time slice, causing it not to be able to run as long as it ought to.
There does exist code to properly reset the elapsed count, but it was
only compiled in a tickless kernel. Now it is built any time
CONFIG_TIMESLICING is enabled.
Issue: ZEP-2107
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add necessary Kconfig and minimal device tree in order to support
STM32F412ZG variant as found on the Nucleo STM32F412 board.
Origin: Original
Change-Id: Ic98a686f478ce551dc6101466ed0cf16924109e8
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Following migration of stm32f1xx series clock control driver to
STM32Cube LL API, cleanup stm32 code base in order to take into
account that this is the only clock driver available for stm32
family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of stm32cube LL based clock control driver,
remove references to former native driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Align stm32f1xx series clock driver to other parts of stm32 family.
Driver support both Connectivity and Density lines of stm32f1 series,
that are based on different Reset and Clock Control architectures.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32F413ZH has 1536kB of Flash and 320kB of SRAM. This
configuration is currently not supported by ST MPU driver, so fill in
the blanks.
Note: The MPU does not support region size that is not a power-of-2 (see
the SIZE field in the MPU_RASR register). This is a problem for our
1536kB Flash region, so it was rounded up to the nearest choice. This is
possible because the memory in the range 0x0818000 - 0x0FFFFFFF is
"Reserved" and thus not mapped anyway.
Change-Id: If0c3d1db564ca45e77f8b5bafa2afdbafa85b40f
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
pop {lr} instruction is not supported in ARMv6-M, fixed by
using pop {r0}; mov lr, r0; instructions.
Jira: ZEP-2222
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
We now have generic ARM M4 MPU support added to Zephyr.
Let's enable it for use with Nordic nRF52 chips.
Memory Layout was generated from Section 8.3 "Memory
Map" of nRF52 Product Specifications (for both nRF52832
and nRF52840):
0x00000000: Flash
0x10000000: Factory Information Config Registers
0x10001000: User Information Config Registers
0x20000000: SRAM
0x40000000: APB Peripherals
0x50000000: AHB Peripherals
0xE0000000: ARM M4 Private Peripheral Registers
NOT Configured:
0x60000000: External RAM
0x80000000: External RAM
0xA0000000: External Device
0xC0000000: External Device
NOTE: More work will be needed for future Nordic MWU (Memory
Watching Unit) support.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This patch add arm core MPU support to NXP MPU driver.
With this feature it is now possible to enable stack guarding on NXP
MPUs.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The STM32L4x SoCs embeds a slightly different embedded flash controller
from the STM32F4x SoCs.
This particular controller has the following properties :
- Up to 2 512KiB banks divided in 2KiB pages
- Flash can be accessed in any sizes
- Flash must be written in 64bit aligned 64bit double-words
The drivers/flash/flash_stm32f4x.c is refactored into a new common
drivers/flash/flash_stm32.c and drivers/flash/flash_stm32l4x.c is
created with the STM32L4x specific functions.
To ease the refactoring and keep common functions, the STM32L4x flash
headers are slightly modified to match the hardware reference naming
and solve compilation issues.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neither ASF nor CMSIS provide defines that can be processed by
the assembler. Exclude those from soc.h. Before this was done
incorrectly in board.h file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patch converts Atmel sam3x MCU series to use register
header files from Atmel Software Framework (ASF) library.
By using ASF different Atmel SAM MCU series can use common
device drivers.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patch adds support for remaining Atmel SAM MCU series,
like sam3x to the common GPIO driver. After this update
full SAM MCU family should be supported by the driver.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add configuration, dtsi and memory configuration fixup for the
STM32F469XI High Performance SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch integrates the thread stack guard feature in the arm
Zephyr core.
Change-Id: I2022899cbc7a340be71cfaa52f79418292f93bae
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the arm core MPU implementation.
This implementation currently supports the thread stack guard feature.
Change-Id: I8b3795ebaf1ebad38aaddc2ed2f05535ead2c09a
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch add arm core MPU support to ARM MPU driver.
Change-Id: I5a61da4615ae687bf42f1c9947e291ebfd2d2c1d
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the arm core MPU interface, a common way to access the
pu functionalities by the arm zephyr kernel.
The interface can be divided in two parts:
- a core part that will be implemented by the arm_core_mpu driver and
used directly by the kernel
- a driver part that will be implemented by the mpu drivers and used by
the arm_core_mpu driver
Change-Id: I590bd284abc40d98b06fdf1efb5800903313aa00
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds initial MPU support to NXP K6x family.
The boot configuration prevents the following security issues:
* Prevent to read at an address that is reserved in the memory map.
* Prevent to write into the boot Flash/ROM.
* Prevent from running code located in SRAM.
This driver has been tested on FRDM-K64F.
Change-Id: I907168fff0c6028f1c665f1d3c224cbeec31be32
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Now that all ARM platforms have a device tree we can move selecting of
HAS_DTS up and remove any !HAS_DTS cases, as well as setting in all the
defconfigs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add defines and pinmux arrays to support more UARTs on STM32F4.
Change-Id: Ib06c549bdb2b3d7065554a0a6d1a3d15441b29c9
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
It is useless to include the pinmux for a peripheral if it is not
enabled in the Kconfig. This is unnecessary and it increases the size of
the binary.
Define macros that will default to void if the associated Kconfig is not
enabled.
Change-Id: I0857fcef335c75b8bb6d537fd859f93d5be4a228
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Clean-up the pinmux arrays as a preparatory work before adding more
pinmuxes.
This is achieved by the following two actions:
- Define the PAD macro to simplify the [x - 1] = y construct
- Reorder the declartions by bank / pin to make it easier to
locate a pin among a high number of other pins, while minimizing the
risk of conflict when two people add a new declaration for two
different pins
Change-Id: I1ca0cc4f48bcd8cfd35b331e9821935f5c855876
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Add necessary Kconfig and minimal device tree in order to support
STM32F413xH variants as found on the Nucleo STM32F413 board.
Origin: Original
Change-Id: I60230c240d6acb610f16a02c62048d448476e9c5
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The bitfield determining the I/O direction already defines the pin
as either input or output, cannot be none or both at the same time
This issue was reported by Coverity
Coverity-CID: 151970
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Not all the boards (for instance the Nuclo F412) use USART1 or USART2.
Let each board enable these USARTs when really used.
Change-Id: Idfe79c724bd7b1ab154310b4a8234b52eef2298d
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Commit 87893ddf7ad4 ("soc: stm32f429zi: rename SOC config flag") renamed
SOC_STM32F429XX to SOC_STM32F429XI but the text of the option should be
changed as well to reflect this restriction in scope.
Change-Id: I2627b59f805e73d6c8a3534e0feec71a4269c9ab
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Commit 599149dfb831 ("soc: stm32f407xg: rename SOC config flag") renamed
SOC_STM32F407XX to SOC_STM32F407XG but the text of the option should be
changed as well to reflect this restriction in scope.
Change-Id: Id03529452f5ec7d7ffee214b152c4aa555e1208a
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Rename SOC_STM32F407XX to SOC_STM32F407XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file).
Change-Id: I0afa16e86b7c99b9e685004f96beeb888f9e7568
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename SOC_STM32F429XX to SOC_STM32F429XI to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: Id188b7703d2bce0a3ded09132ff0f205efa9c143
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename SOC_STM32L476XX to SOC_STM32L476XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: I834bb5b83c24c39e90c0492a2b22a7c7802de361
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The xC tag in the SoC reference indicates the flash size, use it in the
configuration to permit selection of correct flash size for dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch enables the generation of the ARM CMSDK UART base address
from the device tree.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This places a sentinel value at the lowest 4 bytes of a stack
memory region and checks it at various intervals, including when
servicing interrupts or context switching.
This is implemented on all arches except ARC, which supports stack
bounds checking directly in hardware.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Unline k_thread_spawn(), the struct k_thread can live anywhere and not
in the thread's stack region. This will be useful for memory protection
scenarios where private kernel structures for a thread are not
accessible by that thread, or we want to allow the thread to use all the
stack space we gave it.
This requires a change to the internal _new_thread() API as we need to
provide a separate pointer for the k_thread.
By default, we still create internal threads with the k_thread in stack
memory. Forthcoming patches will change this, but we first need to make
it easier to define k_thread memory of variable size depending on
whether we need to store coprocessor state or not.
Change-Id: I533bbcf317833ba67a771b356b6bbc6596bf60f5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The files for the Arduino Due needed to be updated to use the new
configuration when the SoC moved from the atmel_sam3 directory to
the atmel_sam/sam3x directory.
Jira: ZEP-2067
Signed-off-by: Justin Watson <jwatson5@gmail.com>
The FPGA on the MPS2 board implements 4 SBCon devices for I2C which are
connected to:
- a touchscreen controller
- the audio device (for configuration)
- both shield connectors
Change-Id: I55ca985e18b45d68f5e7421c4768dfc9bf2fcb3f
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Converted Stellaris UART driver over to utilize device tree generated
defines. Added a yaml description for the uart, and converted over the
ti_lm3s6965 SoC & qemu_cortex_m3 board port over to utilize it.
Change-Id: Ie20844eb63d2c68eb59ad4160f7f5b5a35e2943b
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a simple device tree for the TI lm3s6965 SoC and QEMU
Cortex-M3 board port. We get flash and memory base addresses and sizes
from the device tree as well as the ARM NVIC number of priority bits.
Change-Id: I4452b5543de7be55518997e54837ccbfd4f121df
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reorder config entries alphabetically to make it easier to add new ones.
Change-Id: Ib118405a150a408638232513fba7198b458ecfa7
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Now that all the nRF based board/SoCs have device trees, we can remove
the Kconfig bits that are now coming from device tree.
Change-Id: Ia1a870a50582d4109070d2833660f58fd6f8691f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree support for nRF51822 SoCs and Arduino 101-BLE,
Curie-BLE, BLE Nano, PCA10028-DK, and Quark-SE BLE boards. This
is minimal support for memory, flash, and UART.
Change-Id: I7e572bea537e384b6d66e520462f023ace0c9b35
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fixup the nRF52840-QIAA to allow getting its SRAM & FLASH sizes from
device tree.
Change-Id: I67ecd7da5f0472402064f158030d9f97f49d7d20
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Nothing calls _ScpMainOscEnable, so lets remove it and associated files
that aren't used anymore.
Change-Id: Ibe900d039c531c4da56baa673d309ee961b09e52
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Cleanup soc code to enable UART_MCUX_LPSCI to support UART0.
Change-Id: I173febffcffc902f228946124e0434f122a67607
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a shim layer around the mcux lpsci driver to adapt it to the Zephyr
serial interface.
Change-Id: I024f1605e3194f34bb57e8a121900e05b3085a82
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for STM32L475xG SoC as a preliminary for
Discovery IOT board support.
stm32l476.dtsi file is now including stm32l475.dtsi
since STM32L476 SoC is a STM32L475 SoC with LCD support
Change-Id: I7567255e4172231cbf4899474617ecae0cd68d64
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of stm32 common clock driver for stm32f4 series
remove references to stm32f4 specific driver.
Change-Id: I372a0ea046007bcb34944d6b2b8880077583b1d3
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit disables native stm32f4x clock control
driver and enables stm32 LL clock control driver
for stm32f4 family
Jira: ZEP-2039
Change-Id: I98ba6c89c4a3a1f39658c5808cd47a2d1f344130
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit enables STM32Cube LL based driver for stm32f4 series.
This generic driver provides a unified API to clock driver for all
stm32 series.
LL API allows driver to be lightweight and to keep genericity across
stm32 family to ease further devlopment and maintenance.
Change-Id: Ie31ae8f433313787f9c9eda77de41925721d54dd
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The CC3220SF is a replacement for the CC3200 SoC, comprising
a network coprocessor and Cortex-M4 MPU.
This leverages the CC3220 SDK driver peripheral library in ROM,
and some files built from ext/hal/ti/.
Jira: ZEP-1958
Change-Id: I892b212c178e05d84ff1d716dde593ced653ae6d
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Adds event based scheduling logic to the kernel. Updates
management of timeouts, timers, idling etc. based on
time tracked at events rather than periodic ticks. Provides
interfaces for timers to announce and get next timer expiry
based on kernel scheduling decisions involving time slicing
of threads, timeouts and idling. Uses wall time units instead
of ticks in all scheduling activities.
The implementation involves changes in the following areas
1. Management of time in wall units like ms/us instead of ticks
The existing implementation already had an option to configure
number of ticks in a second. The new implementation builds on
top of that feature and provides option to set the size of the
scheduling granurality to mili seconds or micro seconds. This
allows most of the current implementation to be reused. Due to
this re-use and co-existence with tick based kernel, the names
of variables may contain the word "tick". However, in the
tickless kernel implementation, it represents the currently
configured time unit, which would be be mili seconds or
micro seconds. The APIs that take time as a parameter are not
impacted and they continue to pass time in mili seconds.
2. Timers would not be programmed in periodic mode
generating ticks. Instead they would be programmed in one
shot mode to generate events at the time the kernel scheduler
needs to gain control for its scheduling activities like
timers, timeouts, time slicing, idling etc.
3. The scheduler provides interfaces that the timer drivers
use to announce elapsed time and get the next time the scheduler
needs a timer event. It is possible that the scheduler may not
need another timer event, in which case the system would wait
for a non-timer event to wake it up if it is idling.
4. New APIs are defined to be implemented by timer drivers. Also
they need to handler timer events differently. These changes
have been done in the HPET timer driver. In future other timers
that support tickles kernel should implement these APIs as well.
These APIs are to re-program the timer, update and announce
elapsed time.
5. Philosopher and timer_api applications have been enabled to
test tickless kernel. Separate configuration files are created
which define the necessary CONFIG flags. Run these apps using
following command
make pristine && make BOARD=qemu_x86 CONF_FILE=prj_tickless.conf qemu
Jira: ZEP-339 ZEP-1946 ZEP-948
Change-Id: I7d950c31bf1ff929a9066fad42c2f0559a2e5983
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Future tickless kernel patches would be inserting some
code before call to Swap. To enable this it will create
a mcro named as the current _Swap which would call first
the tickless kernel code and then call the real __swap()
Jira: ZEP-339
Change-Id: Id778bfcee4f88982c958fcf22d7f04deb4bd572f
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
