There is now a proper function to select the right source IPv4
address when sending a mDNS packet so use it instead of selecting
the address directly from network interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Sync timeouts were calculated incorrectly - this led to a 'Multiple
Masters Issue' as denoted by PTP debugging software.
See 802.1AS-2011, chapter 10.2.4.2 for reference.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Fix the formula listed in help messages which is used to calculate
actual intervals given their log2 values.
It is all calculated properly in the code, because the unit of the
actual field uses the UScaledNs type of which the unit is 2^(-16)ns, so
it is just the help messages that got it wrong.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Calculate proper initial PTP clock divisors based on the MCK value.
Additionally do not allow adjusting the rate of the clock. This does not
seem to work properly with current gPTP rate adjustment algorithm.
Having proper PTP clock divisors and callbacks that allow getting,
setting and adjusting current time is sufficient for proper gPTP
support.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
This enables using these commands to perform discover all procedure:
> gatt-discover-primary
Discover pending
Service 1800 found: start handle 1, end_handle 5
Service 1801 found: start handle 6, end_handle 9
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes bt_gatt_discover perform discover all proceduce if no UUID
is given in the parameters.
Fixes#9713
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Long write procedure currently requires BT_GATT_PERM_PREPARE_WRITE to
be set otherwise the prepares would fail. This changes the behavior so
that BT_GATT_PERM_PREPARE_WRITE enables checking each prepare chunk
skipping it otherwise.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fixed building with ninja adding BUILD_BYPRODUCTS based on suggestion
from @SebastianBoe in issue #7760.
Fixes#7760
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Ninja is much faster than make in the context of CI. The issues with
ninja and parallel builds has been partially resolved in sanitycheck.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Disable cache which increases total execution time without any visible
benefits in the current setup. Need to revisit how we can better use
ccache for CI builds.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Go back to 5 minions, 7 minions is increasing the queue significantly
without any improvements visible in total execution time.
This was changed to 7 to address PRs changing many boards and tests,
which is the exception and not the rule.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The scripts for app_smem need to be ready before the script for
privilaged stack is run. This is needed because there is a small
possibility that the stacks get aligned (due to app_smem)
after privilaged stack script is run. This causes the gperf
to create an incorrect hash.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
We get the following warning when building nrf52810_pca10040:
Warning (avoid_unnecessary_addr_size): unnecessary
#address-cells/#size-cells without "ranges" or child
"reg" property in /buttons
Remove #address-cells/#size-cells since they aren't needed for gpio_keys
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Flash controller-node for stm32f2 based SoCs was missing basic
properties such as compatible, labeln reg and interrupts.
Fix this and add matching yaml binding file;
Fixes#10057
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When we fixed the missing reg property in the cpu node, we forgot to
add #address-cells & #size-cells for the node.
This fix the following warnings we get:
Warning (reg_format): "reg" property in /cpus/cpu@0 has invalid
length (4 bytes) (#address-cells == 2, #size-cells == 1)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get the following warning when building nrf52810_pca10040:
Warning (avoid_unnecessary_addr_size): unnecessary
#address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys
Remove #address-cells/#size-cells since they aren't needed for gpio_keys
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set CONFIG_USERSPACE in the prj.conf to ensure its set, right now
getting CONFIG_USERSPACE depends on tests/Kconfig setting it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This change aims at fixing 'unit_address_vs_reg' warning in
stm32 *-pinctrl.dtsi files.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for led nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@xx' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /soc/virtualcom@0:
node has a unit name, but no reg property
Fix by dropping the unit address from the node name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /flash: node has a reg or ranges
property, but no unit name
or
Warning (unit_address_vs_reg): /memory: node has a reg or ranges
property, but no unit name
Fix by adding unit address that is missing to flash & memory nodes.
Additionally the Silabs memory nodes didn't have a compatiable or
device_type, so add those properties as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /cpus/cpu@0: node has a
unit name, but no reg property
Fix by adding reg property to missing cpu nodes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
_pend_current_thread can return any arbitrary value set by
_set_thred_return_value(), it happens that most cases set 0. This
function can not rely on this behavior otherwise it may return an
invalid value and/or not set data's value.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Make while statement using pointers explicitly check whether
the value is NULL or not.
The C standard does not say that the null pointer is the same
as the pointer to memory address 0 and because of this is a good
practice always compare with the macro NULL.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
MISRA C requires that every controlling expression of and if or while
statement have a boolean type.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Make if statement using pointers explicitly check whether the value is
NULL or not.
The C standard does not say that the null pointer is the same as the
pointer to memory address 0 and because of this is a good practice
always compare with the macro NULL.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
We get several warnings of the form:
Warning (unit_address_vs_reg): /cpus/arcv2-intc@0:
node has a unit name, but no reg property
Fix by removing the unit address from the nodes. Some cases we had a
reg property and a unit address for such interrupt controllers, in those
cases remove both the reg & unit address in the node name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /gpio_keys/joystick@0:
node has a unit name, but no reg property
Fix by dropping the unit address and renaming the node names to include
more information about the gpio_key.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (alias_paths): /aliases: aliases property name
must include only lowercase and '-'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_format): /soc/uart@000003f8:
unit name should not have leading 0s
Fix these by remove the leading 0s.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
10 bit addressing is still not supported on nrf chips, but now
I2C_MSG_ADDR_10_BITS flag is checked.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
This commit adds I2C_MSG_ADDR_10_BITS flag, while keeping
I2C_ADDR_10_BITS for backward compatibility.
I2C_ADDR_10_BITS flag should be removed as soon as all drivers
are modified to use message flag.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Rename _DEVICE_STRUCT_SIZE to _DEVICE_STRUCT_SIZEOF. This causes it to
be picked by the script 'gen_offset_header.py' and inserted into the
header file 'include/generated/offsets.h'.
Renaming from x_SIZE to x_SIZEOF will align it's name with the other
symbols that denote a sctruct's size, like K_THREAD_SIZEOF.
Furthermore, it will allow the symbol to be accessed through a header
file define, instead of only as an extern symbol. This is more
flexible, and more aligned with the other symbols in offsets.
Finally, if we are able to move all of offsets.c symbols into the
offsets.h header file we be able to remove offsets.o from the link and
thereby simplify the linking process.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
For the native_posix backend, use the appropiate tracing
functions and enable color if it should be
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
tests/subsys/logging/log_core does not work if inplace processing
is set and the process thread is disabled.
So let's set the valid configuration in its project file
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Enable native logger backend for native_posix board in defconfig.
Set also logger configuration options suitable for native_posix
backend.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
When CONFIG_LOG_PROCESS_THREAD was not set the logger
was not initialized.
Register a POST_KERNEL init for that case.
Also added an assert in the logger thread in case there
is no backends, instead of having that thread spinning
forever.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
In the POSIX arch, time does not pass inside infinite loops.
=> Add a small delay in each iteration of those loops
when compiled for it.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
For native_posix:
Added command line options to control if traces should have
or not colors.
+
Detect if we are connected to a tty or not, and if we are
set the defaults for that option appropriately
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This allows to define shells which are using different syntax for
commands parsing eg. foocmd=param1,param2.
This is usefull for providing compatibility with existing external
tools while allowing to use Zephyr's shell subsystem.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
None of the data for the CEP, CUD and CPF descriptors needs to be
modified by the stack at runtime. Make it possible to pass constant
data to the descriptor macros, and make sure the descriptor handlers
cast the data back to be a constant.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Update all supported features and peripherals in the official set of
boards from Nordic Semiconductor.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
