Now that the samples use DT generated defines we can remove the
hexiwear_k64 specific ones in board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We update 'blink_led', 'fade_led' and 'rgb_led' to support dt generated
defines for the PWM info needed for each. Since hexiwear_k64 supports
generating the info, moved the support for hexiwear_k64 to just use the
dt generated defines.
For 'blink_led' and 'fade_led' we use an alias in dt called 'pwm-led0'.
For 'rgb_led' we use aliases 'red-pwm-led', 'green-pwm-led' and
'blue-pwm-led'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the Red, Green, & Blue PWM LED info to the device tree. We will use
this in the future for any samples that utilize PWM on these LEDs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add #pwm-cells properties to kinetis dts files and update the yaml
binding to spec the two cells as pin and period (in nanosecond to match
Linux Kernel binding spec).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support to the extract script to handle 'pwms' client properties.
This is pretty much identical to how we hand 'gpios'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
No need to check for BT being enabled. The UART entries will be
available for use if BT is enabled and will do nothing if not.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The wncm14a2a modem is an add-on/shield and not part of the frdm_k64f
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix RCOSC calibration initiation to ensure LF clock is
running; and the HF clock is running with crystal before
triggering the actual calibration in ISR.
Fixes#10811.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Convert gpio_cc32xx driver over to using device tree. Added binding
files, updates to dts for various SoCs that use cc32xx.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Driver for LSM303DLHC accelerometer now supports API function
sensor_attr_set for attribute SENSOR_ATTR_SAMPLING_FREQUENCY.
Signed-off-by: Dennis Wildmark <d.wildmark@gmail.com>
New Qemu is emitting binary charachters which is disturbing generation
of XML, so make sure we only log printable charachters.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This board can run in recent qemu versions (>3.0.0), so enable it
instead of a dedicated qemu board.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In case no transfer is ongoing, the usb_transfer_ep_callback consumes
the received data. This is however associated with the wrong test. USB
is host centric, so data reception on the device is signaled by
USB_DC_EP_DATA_OUT and not USB_DC_EP_DATA_IN.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We set 'use-prop-label' incorrectly in the st,stm32-ccm binding file.
This property is meant to generate names based on there being a label
property set in the node. For st,stm32-ccm nodes we don't ever set
labels and the binding file doesn't specify a label. So remove setting
'use-prop-label'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Group various shell modules for kernel, peripherals and other
subsystems. This will be used to test board functionality interactively
using commands implemented in the individual shell modules.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add basic 'lspci' command to list PCI devices. This command can be
enabled with the new Kconfig PCI_SHELL.
Example:
uart:~$ lspci
0:1 8086:7010 class: 0x1, 1, 4, I/O, addrs: 0xC000-0xC00F, IRQ -1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If data is received before an IRQ handler was set and enabled,
hardware sets the ORE flag. Once set, the IRQ routine starts
hogging the CPU until ORE is cleared. This change will clear
the flag when user code attempts to drain incoming data.
Signed-off-by: Kiril Zyapkov <k.zyapkov@allterco.com>
Added bidirectional I2S support for Intel S1000
- Added implementation for I2S receive mode
- Extended driver instances to support 3 I2S ports
- Added DMA channel mappings for upto 4 I2S ports
- Utilized k_msgq to track buffers through the driver
- Allocate buffers for audio reception in the driver
- Free buffers after audio transmission in the driver
- Perform buffer reload for DMA after every reception/transmission
- Removed unused Kconfig variables
- I2S_CAVS_TX_BLOCK_COUNT
- I2S_CAVS_RX_BLOCK_COUNT
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Added a mechanism to refresh DMA buffers without the
need to call the "configure" API every time.
The reload is done after every DMA completion.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Config API is meant for initial configuration.
Using config API to reload DMA buffers is inefficient and hence
a reload API is added
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Tty device gets only read/write calls, but console retains
getchar/putchar for convenience.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Previously, transmit was effectively non-blocking - a character either
went into buffer, or -1 was returned. Now it's possible to block if
buffer is full. Timeout is K_FOREVER by default, can be adjusted
with tty_set_tx_timeout() (similar to receive timeout).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This allows to specify receive timeout, instead of previously
hardcoded K_FOREVER value. K_FOREVER is still the default, and can
be changes after tty initialization using tty_set_rx_timeout() call,
and timeout is stored as a property of tty. (Instead of e.g. being
a param of each receive call. Handling like that is required for
POSIX-like behavior of tty).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If we don't have Newlib, the more or less POSIX library, it's unclear
how to deal with POSIX stdin/stdout/stderr at all.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This is simplistic implementation which just redirects to (likewise
simplistic) implementation in lib/libc/newlib/libc-hooks.c. This
should be replaced with bindings to "real console", but what should
be a "real console" is so far discussed, at the RFC stage.
This implementation goes into the fdtable.c itself to keep all those
things nicely static. (This is again likely will change when we have
"real console", but again, it's so far not clear where it would
belong, so at least avoid creating random files to be deleted later).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Previously the "socket file descriptors" were just net_context
pointers cast to int. For full POSIX compatibility and support
of generic operations line read/write/close/fcntl/ioctl, the
real file descriptors should be supported, as implemented by
fdtable mini-subsys.
Socket implementation already has userspace vs flatspace dichotomy,
and adding to that ptr-fds vs real-fds dichotomy (4 possible cases)
is just too cumbersome. So, switch sockets to real fd's regardless
if full POSIX subsystem is enabled or not.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
So that client apps can refer to them, and then can be implemented on
Zephyr side as needed.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
read/write/etc. are defined in case CONFIG_POSIX_API is defined, and
we shouldn't provide duplicates.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
All the handling of POSIX file descriptors is now done by fdtable.c.
fs.c still manages its own table of file structures of the underlying
fs lib.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The table allows to wrap read/write (i.e. POSIX-compatible) semantics
of any I/O object in POSIX-compatible fd (file descriptor) handling.
Intended I/O objects include files, sockets, special devices, etc.
The table table itself consists of (underlying obj*, function table*)
pairs, where function table provides entries for read(), write, and
generalized ioctl(), where generalized ioctl handles all other
operations, up to and including closing of the underlying I/O object.
Fixes: #7405
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The define NRF51822 has no in-tree users and is believed to have been
added by accident. The define NRF51 should be referenced in it's
place.
To avoid users accidentally referencing NRF51822 instead of NRF51, and
to avoid confusing users into believing that NRF51822 has semantics we
remove it.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The build script ext/hal/nordic/CMakeLists.txt manages the MDK
dependency. The MDK is not aware of Zephyr and uses it's own defines
to indicate what HW we are building for.
This commit moves these MDK-specific defines out of the 'soc' build
scripts and into the MDK build script where they belong.
This is expected to be a pure refactoring without side-effects.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
