The schematic shows that both INT1 & INT2 from the MMA8652FC are wired
up, update the dts to reflect this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change driver to get I2C address of sensor from the device tree like
most other sensor drivers that utilize device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This sample is linking the 'app' with 'subsys__bluetooth', which will
add zephyr/subsys/bluetooth to the include path of the app. But this
is unnecessary as the app already has this path on it's include path.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
in the _rirq_return_from_coop, a fake irq stack frame is created.
But the value of lp_start, lp_end, lp_count are not set correctly.
When rtie is executed, the zero-overhead loop will be enabled, if
the pc crosses the value of lp_end and lp_count is not zero. The pc
will jump to lp_start. This will break down the system.
This commit fixs this bug and set the correct value of lp_start, lp_end
and lp_count(only need to set lp_count).
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
15.4 MHR is no longer set in net_buf pointed by net_pkt, but in a
separate net_buf, hence we need to check that net_buf now to
determine if we need to wait for ACK or not.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Two issues identified with 6lo fragmentation for ieee802154 that broke
the communication:
1) ieee802154_fragment_is_needed function did not take 15.4 FCS size
into account, hence taking wrong decision in some cases.
2) set_up_frag_hdr was writing with wrong offset, which resulted in 6lo
bytes being overwritten by 15.4 header.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This adds write-without-response-cb command which can be used to
confirm the transmission of the PDU using bt_gatt_write_without_rsp_cb.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds bt_gatt_write_response_cb works similarly to
bt_gatt_notify_cb which can take a callback to be called when the PDU
is considered transmitted over the air.
Note: This can also be used to disable the ATT flow control which would
blocks sending multiple commands without wainting their transmissions.
Fixes#11558
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Legacy shell removed in order to avoid maintaining two shells
systems.
All examples and tests have been migrated to the new shell.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
This is the only use of the k_alert infrastructure in the Zephyr code
base. See whether we can get rid of it.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add mutex to lock STM32 I2C bus in order to guarantee
that data transfers are atomic and have exclusive access
to the bus.
Issue has been found fetching data from multiple sensors
on I2C bus in a mixed context of thread and triggered
interrupt.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lsm303dlhc_accel & lsm303dlhc_magn sensor driver to use new
defines so we can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Driver for networking device Microchip ENC28J60 is used as SPI slave,
moved to DTS type definition. Samples echo_client and echo_server use
this device on Arduino 101 board.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
It was unclear how loading data from persisted storage works.
This patch introduce explanation for that.
Code examples were aligned to recent changes.
Removed misleading information about simultaneous back-end support.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Configuration of Erase command is specified in DTS. Hence
the corresponding changes in Kconfig are removed.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Number of sectors is now calculated from the flash density
i.e. (Flash size)/(sector size).
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
The starting 192kB SRAM is reserved for the mcubootloader. Exclude
this region while building an application to be loaded by mcubootloader.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
FIFO_DEPTH should be in the SoC's Kconfig as this is a
configuration of SPI master controller in SoC.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patchset introduces partitioning of flash in terms of blocks
(flash page layout) for s1000. This partitioning is currently to
be used for mcubootloader.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patch enables the support for FLASH_PAGE_LAYOUT and
FLASH_MAP for the generic spin nor flash driver.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Use DT_ instead of CONFIG_ for spi freq, spi bus name, flash device
name and flash base address.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Update boards yaml file with arduino_i2c supported option
We exclude disco_l475_iot1 from the x_nucleo_iks01a1 sample since there
are duplicated sensors between the disco_l475_iot1 and shield. Until
Zephyr drivers can handle multiple sensors we need to have this exclude.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables instance 3 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1060_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables instance 2 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1020_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts fixups for lpuart instance 2, which will be used for the
arduino_serial connection on the mimxrt1020_evk board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The mcux lpuart shim driver was updated in commit
20202902f2 to use DT_ prefix in all
defined labels not related to Kconfig, but instance 2 was missed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fix the value for Low Power Enable (LP_EN) bit mask.
(Issue described by Coverity CID #188734)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This board has headers for these buses so they should be made available
without requiring special overlays.
Also take advantage of the new Nordic auto-enable for peripherals,
which eliminates the need for special configuration.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
