This commit removes the activation of the FP context
in ARM system boot. There is no need to do this, since
the FP context will be activated in the presence of
floating point instructions. We update the reference
documentation accordingly.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Under Unshared FP register mode we are not sharing the
FP context among different threads, so we do not need to
include the FP high registers bank in the thread.arch
container.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Under Unshared FP register mode we are not stacking the
FP context in exception entries, so we do not need to
include the FP registers bank in the exception stack
frame structure.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Under unshared FP registers mode the FP register bank is
meant to be used by a single thread context. Therefore,
there is no need for automatic stacking of the FP register
bank at exception entries, or context switch, as the
registers are not expected to be shared among multiple
contexts.
Under unshared FP registers mode we only need to clear the
FPSCR register once, before jumping to main(). However, we
initialize the FPSCR already at boot in case FP operations
need to be performed during boot.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In ARM builds with FP services (CONFIG_FLOAT=y) but without user
mode support (CONFIG_USERSPACE=n) we do not need and should not
enable full-access to the FP co-processor. Instead, we should
enabled access by privileged code only.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This is a workaround for IOP issue, where peer rejects LLCP Slave
Connection Parameter Request with LMP Error Transaction Collision
error code even if previous request is complete at the instant.
Signed-off-by: Alexander Svensen <alsv@nordicsemi.no>
On some systems where you don't have access to `PATH` and you can't
set the `ENV{PATH}` variable. You need to be able to pass the path
to the west executable down to the python script so it is better
for it to be set explicitly than assuming that it exsists as a
part of the PATH/executables in the shell being called.
Signed-off-by: Sigvart M. Hovland <sigvart.hovland@nordicsemi.no>
Implementation of pinmux for the stm32mp157c_dk2 board.
Some UART pin mux definition has been added (mainly for
UART console and UART/SPI Arduino shield support).
This can be completed with pin mux for other stm32mp157c
UART.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for stm32mp1 basic UART API with Zephyr.
UART Console and UART shell are also supported.
Async UART API and USART support is to be done.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
net_if_ipv6_calc_reachable_time() requires sys_rand32_get().
Enable the test random number generator so the build doesn't
fail.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Inside void main(void) result of function sensor_trigger_set() is not
checked which might result that function can't set sensor type
and that error can't be handled.
Coverity-CID: 186196
Signed-off-by: Maksim Masalski <maxxliferobot@gmail.com>
Move SERCOM peripherals to use the raw defines generated from DTS
parsing. This adds aliases to the DTS so that the SERCOM number
can still be used for clocking and pinmux.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Increase the resolution of advertising random delay from
1 ms unit to 1 ticker unit.
Relates to #10289, #10391, and #10398.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
According to the Apple iBeacon spec chapter "2.1 Advertising Packet",
"beacons must use a non connectable undirected Advertising PDU,
ADV_NONCONN_IND". Refer to https://developer.apple.com/ibeacon/
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Added prompt to BT_CTLR_RX_PRIO_STACK_SIZE, allowing vendor specific
configuration of high priority Rx thread stack size for
!SOC_COMPATIBLE_NRF.
Signed-off-by: Morten Priess <mtpr@oticon.com>
Fix XTAL advanced feature by adding the missing
implementation to calculate and, retain or release the XTAL
clock source after a Bluetooth state or role is stopped.
Fixes#15817.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add implementation to toggle GPIO Debug pins on HFCLK
request and release by the controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Implement a lower ISR latency ULL processing design. Instead
of looping use ISR/mayfly tail-chaining to process
successive ULL messages.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Implemented ULL to yield from processing in an infinite loop
if current PDU being handled is deferred.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Adds a check in the jlink runner to look for the jlink executables and
print a more useful error message if they are not found.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This adds support for the SAM0 DMA Controller (DMAC). Chained
transfer are not currently implemented.
Tested with tests/drivers/dma/loop_transfer and custom modifications
to that test using three parallel reloading channels. Also tested
with a trivial program that did memory->serial.
Signed-off-by: Michael Hope <mlhx@google.com>
[hageman@inthat.cloud: Rebased and updated commit message]
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
While configure_linker_script() may be useful for other linkers, it
currently only aimed at GNU ld. To really be useful among different
linkers, we would need to abstract its usage of the C preprocessor.
We can do this later, if needed.
No functional change expected.
Signed-off-by: Mark Ruvald Pedersen <mped@oticon.com>
Rather than associating defines within the function, let the call sites
themselves pick the appropriate define. Add new argument for this.
This also permits us to remove regex matching.
No functional change expected.
Signed-off-by: Mark Ruvald Pedersen <mped@oticon.com>
Reduce the amount of {pre,post}fixing magic: I.e. let it be clearer at
call sites that "linker.cmd" is a file, rather than having to know that
"linker" will be postfixed with ".cmd" internally.
Change argument name to linker_script_gen, to better indicate that we
are producing a generated file.
No functional change expected.
Signed-off-by: Mark Ruvald Pedersen <mped@oticon.com>
Now that we avoid the two-step procedure, we can simplify the name of
the construct_add_custom_command_for_linker_pass macro.
Move description comment up to head of definition, making the purpose
clearer.
No functional change expected.
Signed-off-by: Mark Ruvald Pedersen <mped@oticon.com>
Change construct_add_custom_command_for_linker_pass from function into
macro. The purpose of the function was to set the output variable to a
string that would be fed to add_custom_command. This meant all use
required a two-step procedure and an intermediate
variable (custom_command).
The environmental leakage from a macro in this case is small, so let's
just simplify to a macro and avoid the two-step.
No functional change expected.
Signed-off-by: Mark Ruvald Pedersen <mped@oticon.com>
Full grep reveal ALIGN_SIZING_DEP is only mentioned in cmake, where
it is never assigned a value.
No functional change expected.
Signed-off-by: Mark Ruvald Pedersen <mped@oticon.com>
There are limits to CMSIS stack sizes, we can't just
add a number to it. Use the configured maximum.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Set to same default as regular stacks. This doesn't use
any extra memory until CMSIS_V2_THREAD_DYNAMIC_MAX_COUNT
is set. 0 is not a valid default if that is set.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Update the name of mem-domain API function to add a partition
so that it complies with the 'z_' prefix convention. Correct
the function documentation.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
