The arm-clang compiler/linker does not optimize away unused function
symbols and thus will error if symbols that are referenced are not
defined. To fix this add needed ifdef'ry.
Build various network samples that utilize ethernet but don't have
CONFIG_NET_PROMISCUOUS_MODE will get a link error for:
Error: L6218E: Undefined symbol
net_mgmt_NET_REQUEST_ETHERNET_SET_PROMISC_MODE
(referred from ethernet.o).
Fix by adding ifdef protection around promisc code.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Move net iface tests to use new ztest API
1. Add teardown, remove addr and interface down
2. Add pkt unref
3. Combine interface up/down, promisc off/on, addr add/rm
Signed-off-by: Hu Zhenyu <zhenyu.hu@intel.com>
Modify the tests so that they verify that only allowed thread
is able to modify network interface data.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that user is able to toggle promiscuous mode flag
in network interface level and that flag value is passed
to device driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of always allocating both IPv6 and IPv4 address information
to every network interface, allow more fine grained address
configuration. So it is possible to have IPv6 or IPv4 only network
interfaces.
This commit introduces two new config options:
CONFIG_NET_IF_MAX_IPV4_COUNT and CONFIG_NET_IF_MAX_IPV6_COUNT
which tell how many IP address information structs are allocated
statically. At runtime when network interface is setup, it is then
possible to attach this IP address info struct to a specific
network interface. This can save considerable amount of memory
as the IP address information struct can be quite large (depends
on how many IP addresses user configures in the system).
Note that the value of CONFIG_NET_IF_MAX_IPV4_COUNT and
CONFIG_NET_IF_MAX_IPV6_COUNT should reflect the estimated number of
network interfaces in the system. So if if CONFIG_NET_IF_MAX_IPV6_COUNT
is set to 1 and there are two network interfaces that need IPv6
addresses, then the system will not be able to setup IPv6 addresses to
the second network interface in this case. This scenario might be
just fine if the second network interface is IPv4 only. The net_if.c
will print a warning during startup if mismatch about the counts and
the actual number of network interface is detected.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This should clear up some of the confusion with random number
generators and drivers that obtain entropy from the hardware. Also,
many hardware number generators have limited bandwidth, so it's natural
for their output to be only used for seeding a random number generator.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
In many networking tests we had to configure SLIP in the prj.conf
leaving those configurations Qemu specific. This change enables SLIP for
QEMU targets automatically and allows reuse of prj.conf for multiple
boards.
Additionally, the TUN options is removed. This option was not used
anywhere.
To enable self-contained networking tests that do not depend on SLIP, we
introduce the new option NET_TEST which disables TAP and allows testing
in QEMU without the need for a host interface.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
When we setup the network interface, add predefined IPv6 multicast
groups into the network interface. When interface is taken down,
then leave all the multicast groups that joined.
See RFC 4291 ch 2.8 for details.
Change-Id: If17d3e8c75157a02aa93c92e2fb499619c1484cf
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive lot of packets, it might happen that we exhaust
all the DATA buffers in the system. This would prevent from
us sending anything to the network.
Change this by splitting the DATA buffer pool into RX and TX
parts. This way RX flooding cannot consume all DATA buffers
that needs to be sent.
Change-Id: I8e8934c6d5fdd47b579ffa6268721b5eb3d64b6d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
