In order to take granular input use micro seconds as input for TWT
intervals, this helps us in providing inputs such as 65.28ms without the
need of using floating points.
This also expands the TWT wake interval range to 262.144ms, earlier as
we want to use uint8, limited to 256ms.
Also, remove the units from the variable names, this is unnecessary and
also avoids doing breaking changes.
Update release notes as this is a breaking change, both type and
variable names are changed.
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
In the case of no ARP entry, the incoming packet is added to the ARP's
pending queue, while ARP is being resolved. Here a reference is taken
by the ARP layer to the packet to avoid it being freed, but the Ethernet
immediately puts down the reference and send the ARP packet to the
driver.
If the ARP request fails for some reason, L2 returns failure to net_if
which then puts down the reference and the packet will be freed as the
reference count is now zero.
But the packet is still in the ARP's pending queue and after timeout
ARP will put down the reference causing double free bus fault (double
free message is only seen if the CONFIG_NET_PKT_LOG_LEVEL_DBG is
enabled, so, a bit hard to debug.
Fix this by clearing the ARP entry and pending queue after taking a
reference and then free ARP packet, IP packets are either freed by ARP
pending queue drain or net_if layer.
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
According to RFC3927, hosts with only IPv4 LL address should still be
able to send packets to destination w/o IPv4 LL address:
A host with an IPv4 Link-Local address may send to a destination
which does not have an IPv4 Link-Local address. If the host is not
multi-homed, the procedure is simple and unambiguous: Using ARP and
forwarding directly to on-link destinations is the default route
This behaviour however was not possible with Zephyr, which only allowed
to use IPv4 LL source address for IPv4 LL destinations.
Fix this, by introducing a final fallback (only if IPv4 autoconf is
enabled), to select IPv4 LL address as a source address if no other
address is available.
Additionally, modify the ARP routine a bit if IPv4 LL address is in use.
There's no really point to forward the packet to gateway if IPv4 LL
address is used, as such addresses are not routable. Instead, try to
find the peer in local network in such case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Fixes dead code warning. At this point we have already checked for
broadcast and it is set to false.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The following fixes were applied:
- Multicast Rx packets stats were not recorded due not parsing the
ethernet header. The function that tried to parse the ethernet header
was parsing the ethernet packet beyond the ethernet header.
- Added a new stats for unknown protocol which gets updated when the
ethernet layer encounters an unknown ethernet packet type.
Fixes#53994
Signed-off-by: Chamira Perera <chamira.perera@audinate.com>
Add support for configuring power save timeout in Wi-Fi chipsets.
Changes to configure power save inactivity timer.
Signed-off-by: Ajay Parida <ajay.parida@nordicsemi.no>
A follow up to commit 1d7a077e11 - apparently the PPP interface should
not be brought entirely down internally, as this can break further
communication with the host. Because of that, reintroduce functionality
that used to be covered by net_if_carrier_down() (which basically
skips the L2 enable(false) call), but limited to PPP scope only.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This commit updates all in-tree code to use `CONFIG_CPP` instead of
`CONFIG_CPLUSPLUS`, which is now deprecated.
Signed-off-by: Stephanos Ioannidis <stephanos.ioannidis@nordicsemi.no>
Wi-Fi bands are regulated by a governing body depending on operating
country, add support for the user to provide a country of operation as a
hint to the Wi-Fi chipset.
Ideally if the chipset supports this is all handled internally, in that
case "get" is useful but for testing and other usecases add a "set" as
well, similar to "iw reg set" or "country_code=" configuration in
hostapd/wpa_supplicant in Linux world.
This add a new offload API operation "reg_domain" that can be used to
either get or set the regulatory information.
The validation is left to the underlying chipset, shell only does basic
validation, (XY/00).
This is just a regulatory hint to the chipset, there could be other
regulatory hints e.g., beacon that can override this configuration, so,
an additional option to force this setting despite other hints is also
given for testing purposes.
FYI, the standard database used is [1].
[1] - https://git.kernel.org/pub/scm/linux/kernel/git/sforshee/wireless-regdb.git/tree/db.txt
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
As we have to provide LL addresses in big endian to userspace to be
POSIX compliant and we also do not want to reserve extra space for
such addresses, bff6a5cce5 introduced
a change that swaps address bytes in place in the packet before
returning the packet with LL address pointers to userspace.
Unfortunately a regression sneaked into the code base while doing
so: The byte swapping was duplicated when using 6LoWPAN compression
and the byte swapping caused decryption to fail in some cases,
see #53630. This commit fixes the problem.
Fixes: #53630
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
The L2 networking layer checks for return value from enable, but
Ethernet is not checking and always returns 0, so, relay the return
value from the Ethernet driver to networking stack.
This fixes the issue of interface start failing but interface still
being up.
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
Add a new callback list structure for state change information.
These APIs are meant to eventually replace the single callback API
provided by openthread_set_state_changed_cb().
This will allow multiple users to gain information about
OpenThread stage changes.
Note CONFIG_OPENTHREAD_MAX_STATECHANGE_HANDLERS
with OpenThread's otSetStateChangedCallback() API can also be
used to enable registration of multiple callbacks of this type but this
cannot be modified if a certified OpenThread binary is used in the
build.
Signed-off-by: Nick Ward <nick.ward@ftpsolutions.com.au>
Setting a detected packet family (ipv4 or ipv6) in net_context level
instead in lower layers for AF_PACKET/SOCK_RAW/IPPROTO_RAW type sockets
when sending data.
Signed-off-by: Jani Hirsimäki <jani.hirsimaki@nordicsemi.no>
The IPv4 autoconfiguration feature relies on the fact, that autoconf
ARP packets are always prepared by the ARP module. After recent ARP
refactoring though that could no longer be the case due to packet
queueing mechanism. This could lead to net pkt leaks in the autoconf
module.
Fix this by skipping the pending packet queue for autoconf packets.
Since for autoconf ARP requests there's no really a pending packet
to queue, it can be safely avoided. This results in the ARP request
being always sent for the autoconf case, preventing the packet leak.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Initializing an event callback with net_mgmt_init_event_callback() just
sets some of the callback fields but do not propagate those masks in the
core. If we want to use the callback, it is necessary to also call
net_mgmt_add_event_callback().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The current association logic starts by changing the channel. The way it
is done is wrong because it dereferences req->channel which is simply
not initialized by the caller. But anyway, the command itself does not
support providing a channel so we must already be on the right one when
trying to associate. Hence, drop this channel change call.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
During an association, the peer we are trying to connect to will send us
an association response frame with the destination PAN ID set to the PAN
ID we try to join. If we do not update the hardware address filters
beforehands, it is likely that the hardware will just discard the
response and the association will fail.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
While the packet structures seem to always be reset when they are
allocated, it's apparently not the case of the data buffers. Indeed,
these are allocated differently and just attached to the packet
structure through a frag/buffer member.
Experience shows that we may get uninitialized buffers so let's set
all MAC parameter bits one by one, even the reserved ones.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The spec clearly states: "association requests shall set the AR bit".
Even though Zephyr can currently only implement RFD devices which are
not expected to support incoming association requests, because this MAC
command is actually processed until being voluntarily ignored, let's
ensure the expected "ar" value is right to avoid failing because of a
wrong reason.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When validating a MAC command, the "src" and "dst" fields may be set to:
- IEEE802154_ADDR_MODE_SHORT (0x2)
- IEEE802154_ADDR_MODE_EXTENDED (0x3)
- IEEE802154_ADDR_MODE_SHORT | IEEE802154_ADDR_MODE_EXTENDED (0x3)
Hence when the mode check happens, any times the mode is set to SHORT
the check will fail while in practice it was meant to be valid because
the check is:
if (src_mode == src || dst_mod == dst)
Use bitfields when relevant so that when checking capabilities we use
the bit offsets rather than the plain numbers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When validating a MAC command, there is sometimes a misunderstanding of
what "src" and "dst" length mean.
There are actually two fields in the MHR:
- One giving the type of address, if it is short or extended, it is the
value provided by the macros IEEE802154_ADDR_MODE_{SHORT,EXTENDED} and
their respective decimal values are 2 and 3.
- One giving the size of the address field, this is
IEEE802154_{SHORT,EXT}_ADDR_LENGTH and their value is actually 2 and 8
(bytes).
The function validate_mac_command() provides inputs to
validate_mac_command_cfi_to_mhr() which expects the former information.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Clean up occurrences of "#if IS_ENABLED(CONFIG_FOO)" an replace
with classical "#if defined(CONFIG_FOO)".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
IEEE802154 L2 may modify the LL address during interface operation (when
processing MAC command). So far the L2 workaround the LL address update
protection by clearing the NET_IF_UP flag temporarily, but due to recent
changes it no longer works. Update this workaround to verify
NET_IF_RUNNING flag instead.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
After network interfaces state handling rework, it's no longer correct
to verify the connection status on `net_if_up()`, as this only changes
the administrative state of the interface. The interface won't be put in
operational UP state until it's connected.
This check prevented the interface from being brought up during system
boot.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Setting the protocol type for raw IP packets to be sent so that they
can be passed to Ethernet.
Signed-off-by: Jani Hirsimäki <jani.hirsimaki@nordicsemi.no>
net_pkt_get_frag() and a few other functions did not specify the
allocated fragment length, incorrectly assuming that fixed-sized
buffers are always used.
In order to make the function work properly also with variable-sized
buffers, extend the function argument list with minimum expected
fragment length parameter. This allows to use net_buf_alloc_len()
allocator in variable buffer length configuration, as well as verify if
the fixed-sized buffer is large enough to satisfy the requirements
otherwise.
Update the existing codebase to provide the expected fragment length,
based on the context.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This reverts changes introduced in commit
dd535f611d, as they broke the gsm_ppp
driver integration with PPP L2. Apparently, a more thorough
refactoring is needed to use the new interface management scheme with
PPP.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In order to avoid using multiple sources of truth for the platfom's
endianness, convert the in-tree code to use the (BIG|LITTLE)_ENDIAN
Kconfig variables exclusively, instead of the compiler's
__BYTE_ORDER__.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When security type is not given but instead MFP is given, MFP setting
will be considered as security type, this is because both are optional
and no way to distinguish them easily.
Make security type mandatory for MFP selection, this way we either
assume defaults for both security type and MFP or explicitly ask user
for both. Reword the help text to reflect this.
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
Align virtual L2 with interface state handling update. Introduce
net_virtual_enable() function, which gets called whenever a network
interface is brought up (operational). This, combined with already
existing net_virtual_disable() function, can be used to update the
carrier state on the virtual interface, based on the underlying
interface status.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Align PPP drivers/L2 with interface state handling update. Use the
carrier on/off notification instead of bringing the interface up/down to
update the interface state.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Align OpenThread L2 with interface state handling update. Use the
dormant flag to indicate whether an interface joined a Thread network.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Align Bluetooth L2 with interface state handling update. Use the dormant
flag to indicate whether interface has a Bluetooth connection or not.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Align Ethernet/Wi-Fi drivers/L2 with interface state handling update.
For drivers, that did not support carrier detection, no changes are
needed.
Driver that did support carrier detection, are updated to set the
carrier state to OFF by default, instead of setting the
NET_IF_NO_AUTO_START flag. This allows to postopne the actual
NET_EVENT_IF_UP notification until driver detects that carrier is ready.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The IEEE 802.15.4 L2 now sets the ll protocol in the packet to a
specific value. This corresponds to the respective solution in Linux and
is required to validate access to IEEE 802.15.4 specific attributes of
the packet.
Later change sets will rely on this value to ensure that IEEE 802.15.4
specific package content can only be accessed on IEEE 802.15.4 packages.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Most IEEE 802.15.4 drivers do not support promiscuous mode, some do.
There is a dedicated L2 flag to signal this capability to clients.
Unfortunately the IEEE 802.15.4 L2 stack does not announce this flag
even for drivers that correctly expose it in their HW capabilities.
Some clients (notably the OpenThread L2) even uses promiscuous mode
without checking whether the driver actually supports it.
This change lets the vanilla IEEE 802.15.4 L2 check the driver's
HW capabilities to announce promiscuous mode on its 'get_flags()'
interface if supported.
The OpenThread L2 uses a constant (potentially incorrect) response
to 'get_flags()'. Fixing the OpenThread L2 is out of scope of this
change. This change just introduces TODO messages to the OpenThread code
so that the OpenThread team may fix the issue (or delete the TODO if they
deem it irrelevant).
Fixes: #51263
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
The bridge subsystem was written with a ETH_BRIDGE_INITIALIZER that
assumed it could initialize a k_mutex with a zero-filled initializer.
That never worked. Unlike semaphores, mutexes have always required a
runtime call to k_mutex_init(). What happened instead is that
k_mutex_un/lock() returned error codes, which were ignored by the code
here. So no locking was happening.
This was discovered while migrating to zync, where an attempt to
unlock an unlocked mutex is a panic condition (and where zero-filled
initializers are legal, but represent an unfair semaphore and not a
mutex, so deadlock correctly).
Signed-off-by: Andy Ross <andyross@google.com>
This fixes the output below by moving the closing bracket to "<Security
type (optional: valid only for secure SSIDs)>" after the enumeration of
security types "0:None, 1:PSK, 2:PSK-256, 3:SAE".
Fixes:
uart:~$ wifi
wifi - Wi-Fi commands
Subcommands:
connect :Connect to a Wi-Fi AP
"<SSID>"
<channel number (optional), 0 means all>
<PSK (optional: valid only for secure SSIDs)>
<Security type (optional: valid only for secure SSIDs)>
v----------------------^
0:None, 1:PSK, 2:PSK-256, 3:SAE
(...)
Signed-off-by: Gaël PORTAY <gael.portay@gmail.com>
Return to line after the first parameter to:
- have the second parameter in a single line (not splitted) and
- start every parameters from a brand new line (easier to read)
Signed-off-by: Gaël PORTAY <gael.portay@gmail.com>
This fixes the output below by adding the missing closing bracket to
"<MFP (optional): 0:Disable, 1:Optional, 2:Required":
Fixes:
uart:~$ wifi
wifi - Wi-Fi commands
Subcommands:
connect :Connect to a Wi-Fi AP
"<SSID>"
<channel number (optional), 0 means all>
<PSK (optional: valid only for secure SSIDs)>
<Security type (optional: valid only for secure SSIDs)>
0:None, 1:PSK, 2:PSK-256, 3:SAE
<MFP (optional): 0:Disable, 1:Optional, 2:Required
^-------------------------------------------------^
(...)
Signed-off-by: Gaël PORTAY <gael.portay@gmail.com>
This fixes the output below by returning to line after "Connect to a
Wi-Fi AP":
Fixes:
uart:~$ wifi
wifi - Wi-Fi commands
Subcommands:
connect :Connect to a Wi-Fi AP"<SSID>"
^------^
<channel number (optional), 0 means all>
(...)
Signed-off-by: Gaël PORTAY <gael.portay@gmail.com>
The LLDN frame has been obsoleted in IEEE 802.15.4-2015f. This change
removes it from the code, introduces frame types from current spec
levels and updates the frame validation rules in accordance with the
spec.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Several attributes in the ieee802154_context struct may potentially be
accessed from different threads and/or ISR context. Only some of these
attributes were properly guarded against race conditions.
This may not have been to problematic in the past but as other changes
in this PR introduce additional attributes and mutate several attributes
in a single atomic transaction, leaving such changes unprotected seems
dangerous.
This change therefore introduces systematic locking of the
ieee802154_context structure.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
IEEE 802.15.4 short address support is incomplete in several places.
This change improves short address support without claiming to fix
it everywhere. Future iterations will have to continue where this change
leaves off.
The purpose of this change was to:
* use the short address returned by association responses,
* automatically bind IEEE 802.15.4 datagram sockets to the short
address if available,
* use the short address in outgoing packages where applicable,
* improve validation of association/disassociation frames,
* model association more closely to the spec by tying it to the
existence of a short address in the MAC PIB thereby removing
redundancy in the PIB (which makes race conditions less probable),
* keep both, the short and extended addresses, of the coordinator.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
This changes fixes several bugs and inconsistencies in the IEEE 802.15.4
L2 implementation. These bugs were revealed while documenting intended
endianness of driver, IP, socket and L2 attributes (see previous
changes).
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
This is a preparatory change that fixes one aspect of short address
handling before fixing endianness so that the endianness fix can be
applied consistently in this method.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
The IEEE 802.15.4 L2 code stores representation of attributes like
PAN id, short address and extended address in different encodings:
* big endian for extended address and CPU byte order for everything
else whenever such attributes enter user space (except for IP/socket
link layer addresses which are always big endian - even in case of
short addresses - to maintain POSIX compatibility).
* little endian for everything that is close to the radio driver as
IEEE 802.15.4 frames are little endian encoded.
Endianness was almost nowhere documented which led to several bugs and
inconsistencies where assignments of different byte order were not
converted (or sometimes converted, sometimes not).
This change documents endianness wherever possible within the realm of
the IEEE 802.15.4 L2 code. Conversion bugs and inconsistencies that were
revealed by the improved documentation will be fixed in a separate
commit.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Instead of using "select" on certain EC configurations, which is
considered unsafe for various reasons, use a "depends on" and rely on
the user to set a proper configuration in the config file.
Update the respective project configurations to comply with the new
configuration scheme.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
When switching from a secure network to open network, the previous
parameters are not reset which causes the open connection to fail.
Remove the unnecessary "static" storage and reset to zero for params.
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
This fixes a bug with ARP and multiple outgoing packets with an IP
that needs to be resolved, causing the first packet to go out and
all others to be dropped after the timeout by having a FIFO of
pending packets instead of a single packet.
Signed-off-by: Jamie McCrae <spam@helper3000.net>
As of today <zephyr/zephyr.h> is 100% equivalent to <zephyr/kernel.h>.
This patch proposes to then include <zephyr/kernel.h> instead of
<zephyr/zephyr.h> since it is more clear that you are including the
Kernel APIs and (probably) nothing else. <zephyr/zephyr.h> sounds like a
catch-all header that may be confusing. Most applications need to
include a bunch of other things to compile, e.g. driver headers or
subsystem headers like BT, logging, etc.
The idea of a catch-all header in Zephyr is probably not feasible
anyway. Reason is that Zephyr is not a library, like it could be for
example `libpython`. Zephyr provides many utilities nowadays: a kernel,
drivers, subsystems, etc and things will likely grow. A catch-all header
would be massive, difficult to keep up-to-date. It is also likely that
an application will only build a small subset. Note that subsystem-level
headers may use a catch-all approach to make things easier, though.
NOTE: This patch is **NOT** removing the header, just removing its usage
in-tree. I'd advocate for its deprecation (add a #warning on it), but I
understand many people will have concerns.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The IEEE 802.15.4 security implementation had several severe bugs:
* A regression introduced by 6ea225e34a
(net/ieee802154: Finally removing usage of ll_reserve in L2)
introduced a buffer leak (reading/ writing beyond the end of the frame
buffer) and led the security implementation to malfunction in all but
the simplest cases (i.e. encryption/authentication: none).
* Encryption vs. authentication modes were not properly implemented i.e.
encryption was always active even if not required by the chosen
encryption level.
* Nonce endianness was not correctly handled on decryption of packets
which led to authentication failures.
* The frame counter was not checked for overflows.
* The encryption output buffer limit (out_buf_max) was not correctly set.
* Setting an invalid key mode led to a NULL pointer deref.
* We use CCM rather than CCM* as crypto.h does not provide access to
CCM*. CCM does not support encryption-only operation, though. This
condition was not checked by the code.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
This change makes the packet socket and ieee802154 l2 drivers aware of
AF_PACKET sockets, see https://github.com/linux-wpan/wpan-tools/tree/master/examples
for examples which inspired this change.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Some IEEE 802.15.4 specification constants must be made available in
userspace as they will be needed to use IEEE 802.15.4 RAW/DGRAM sockets
which will be introduced in this changeset.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Zephyr IEEE 802.15.4 drivers and L2 stack use the same constant names
for different MTU definitions. The intent of this change is to introduce
a consistent MTU definition which can be used everywhere in zephyr to
avoid confusion, bugs and name conflict.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Newly introduced Coverity scan throws a warning about duplicate tag as
per MISRA coding standards, so, use a unique tag name in the existing
code for "shell".
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
Networking statistics framework is used to define handler and the data
structure, Wi-Fi management layer implements the handler and also adds a
new offload API to get statistics from the Wi-Fi driver.
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
A new net_mgmt command and event are added for interface status,
depending on the implementation the status can be returned when polled
or an unsolicited event can be send by driver whenever there is a change
in status.
This is planned to be implemented only by upcoming wpa_supplicant,
offload implementation is left for driver developers.
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
Add `OPENTHREAD_CONFIG_MESSAGE_BUFFER_SIZE` to Kconfig.
Also set the number of children to minumum possible for MTD builds
in order to save some resources (~512B of RAM).
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
ppp_send_pkt() function can be called with NULL fsm parameter (when
PPP_PROTOCOL_REJ packet was sent), howerver this was not taken into
consideration when ppp_context was retrieved. In result, this could lead
to NULL pointer dereference an crash.
Fix this, by moving the ppp_context extraction directly where it's
actually used (PPP_CODE_REJ packet type handling). In such case, fsm
point should not be NULL.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Wi-Fi protocol uses EAPoL ether type frames for authentication, so, add
support for that ether type so that they are not dropped.
Though we have NET_ETHERNET_FORWARD_UNRECOGNISED_ETHERTYPE to allow
unknown frames to be passed up the stack, but this might cause
performance penalty.
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
This change makes the files which are part of this changeset comply to
the project's coding style rules as defined in .clang-format.
This required addition of some forward declarations and additional
dependencies into header files as some of them depended on the order of
header inclusion which was changed due to alphabetical ordering of
includes.
Background: .clang-format states "SortIncludes:true" which will force
re-ording of include-statements which in turn might break the build if
header file inclusion is not order-independent.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
6LoWPAN fragmentation is not related to IEEE 802.15.4 proper but is just
part of its IPv6-specific L3-adaptation layer. To make this more obvious
we rename all resources related to 6LoWPAN fragmentation.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
This change decouples the IEEE 802.15.4 (L2) layer from all IPv6 (L3)
concerns.
Applications may now choose to set CONFIG_NET_6LO=n and
CONFIG_NET_L2_IEEE802154=y at the same time.
Setting CONFIG_NET_6LO=n will build a vanilla IEEE 802.15.4-2006 specs
compliant L2 layer without any reference to 6LoWPAN or IPv6. This allows
application developers to design custom non-IP protocols on top of
IEEE 802.15.4-2006 and thereby makes the L2 layer much more re-usable.
Fixes#48585.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
This change contains some merely editorial changes to inline comments
plus updates references from the IEEE 802.15.4-2003 spec to
IEEE 802.15.4-2006 which corresponds to the implementation level of
the module.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Most existing TODO markers (as well as VSCode default settings) favor
TODO over ToDo - so let's make this a little bit more consistent in the
IEEE 802.15.4 module.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
The L2 protocol type information is not carried to the upper layers.
This is problematic for packet sockets, as the address structure in
recvfrom() is supposed to provide this information.
Fix this by adding ll_proto_type field in the net_pkt structure.
Set the protocol type in the Ethernet L2 when packet is processed.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Driver function was called with wrong parameter, which resulted
in filter being added instead of removed
Signed-off-by: Tomislav Milkovic <milkovic@byte-lab.com>
irq_lock() returns an unsigned integer key.
Generated by spatch using semantic patch
scripts/coccinelle/irq_lock.cocci
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Move the CAN bus network driver from drivers/can to drivers/net as it
implements a network driver, not a CAN controller driver.
Use a separate Kconfig for enabling the CAN bus network driver instead of
piggybacking on the SocketCAN Kconfig. This allows for other
(e.g. out-of-tree) SocketCAN transports.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move OpenThread's glue code along with the Kconfig files that configure
OpenThread stack itself into module directory.
Update the maintainers file to reflect this change.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Make sure MAC software transmission security is enabled by default
for Thread 1.3 builds as well.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Logging v1 has been removed and log_strdup wrapper function is no
longer needed. Removing the function and its use in the tree.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
In case NET_MGMT_EVENT module was enabled but w/o NET_MGMT_EVENT_INFO,
the OpenThread integration layer failed to build as the "info" field in
the net mgmt callback structure is not available then.
Fix this by conditionally enabling code processing the event only if
NET_MGMT_EVENT_INFO is enabled. Otherwise, print a warning, as the event
is not really useful if no address information is provided.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add Kconfig option to the Ethernet L2 which allows to forward frames
with unknown EtherType further into the stack. This can be useful for
packet sockets, where further frame processing is application dependent.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Get actual keys from references when PSA crypto is enabled.
A more secure method should be implemented once 802.15.4 platforms
support other than clear text keys.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Thread network makes no use of Solicited-node multicast addresses,
thereby do no create them on the interface to save multicast address
entries for important ones.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
There is a risk of deadlock in case net_if APIs are used from within
net_mgmt handlers as both module APIs are protected with their own
mutexes.
The scenario observed with OpenThread happend when
NET_EVENT_IPV6_ADDR_ADD/NET_EVENT_IPV6_MADDR_ADD events were processed.
The net_mgmt mutex is locked when both, an event handler is being
processed (from a separate net_mgmt thread) and when an event is raised
(for example when a new address is added on an interface). In case a
net_mgmt handler tried to use some mutex-protected net_if API, we could
end up in a deadlock situation - the net_mgmt would wait for the net_if
mutex to release, while some other thread (in this case main during
initialization) could wait within some net_if function, pending on
net_mgmt mutex to be released to notify the event.
Fix this, by preventing net_if APIs from being used from within OT
net_mgmt handlers.
Additionally, simplify the net_mgmt handlers logic, by making use of
additional info provided with an event. Instead of blindy assuming that
recently added address was the last on the list (which might not always
be the case, if addresses are added/removed dynamically), read the
actual address being added from the net_mgmt_event_callback structure.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In order to bring consistency in-tree, migrate all subsystems code to
the new prefix <zephyr/...>. Note that the conversion has been scripted,
refer to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Name OpenThread version selection option to `OPENTHREAD_STACK_VERSION`
to be able to superseed it somewhere else.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
CONFIG_NET_L2_PPP_MAX_TERMINATE_REQ_RETRANSMITS
was not having any impact and
CONFIG_NET_L2_PPP_MAX_CONFIGURE_REQ_RETRANSMITS
was used incorrectly instead for terminate().
Signed-off-by: Jani Hirsimäki <jani.hirsimaki@nordicsemi.no>
Making sure struct bt_l2cap_chan has absolutely no members related
to dynamic channels.
That way we ensure that there is no overhead for a build where only
fixed channels are used.
It's not enough that the dynamic channel-related members are put behind
ifdefs - they should be completely moved out from the struct definition.
Furthermore, the public l2cap.h header file already has a struct
that's meant to be used for dynamic channels: struct bt_l2cap_le_chan!
However, currently dynamic channel support is a mess - it's a mix
between these two structs. The bt_l2cap_le_chan struct should really
be an extension of the bt_l2cap_chan struct, i.e. the former should
contain as a member the latter.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
NSEC_PER_SEC is an unsigned integer macro. Thus, -NSEC_PER_SEC will be
treated as unsigned integer as well which lead to calculation error on
64bits integer variables. Added the correct type casting into the formula
to fix the calculation error.
Signed-off-by: Kweh Hock Leong <hock.leong.kweh@intel.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Fix#42800
Both pss->rate_ratio and port_ds->neighbor_rate_ratio are double type
but sync_receipt_time is uint64_t. If pss->rate_ratio is less than 1
or sync_receipt_time * port_ds->neighbor_rate_ratio is less than 1,
sync_receipt_time becomes 0 due to double to uint64_t cast.
Assign port_ds->neighbor_prop_delay to sync_receipt_time first to fix
this issue.
Signed-off-by: Lu Ding <lucasdinglu@gmail.com>
This commit moves openthread CMakeLists.txt from openthread submodule
to zephyr/modules/openthread.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
correction field in sync follow up message must be converted from host
endianness to network endianness.
Signed-off-by: Lu Ding <lucasdinglu@gmail.com>
This file defines the crypto driver API, cipher is supposed to be just
one type of capability (other can be hash) of these drivers, just
change the file name to be consistent with it.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
If OPENTHREAD_IP6_FRAGM is enabled the IPv6 fragments are handled in
OpenThread stack but also forwarder unconditionally to the Zephyr
uplayers. It causes additional packets processing and leads to errors
like unrecognized next header type or duplicate ping reply. What more
these errors generate additional traffic which jam channel and decrease
latency for packets required fragmentation.
This commit add filtering IPv6 fragments when data fragmentation and
reassembling is enabled in OpenThread.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
Takes the modem state machine by calling lcp_close instead of lcp_down
Using this method the LCP layer sends a TERMINATE_REQ to the modem and the
network interface is only taken down when the LCP layer has properly
finished.
Moved the ppp_mgmt_raise_carrier_off_event and net_if_carrier_down
to lcp.c to avoid breaking the interface.
Tested on a real modem.
Fixes: zephyrproject-rtos#41627
Signed-off-by: Sjors Hettinga <s.a.hettinga@gmail.com>
A common pattern here was to take the work item as the subfield of a
containing object. But the contained field is not a k_work, it's a
k_work_delayable.
Things were working only because the work field was first, so the
pointers had the same value. Do things right and fix things to
produce correct code if/when that field ever moves within delayable.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
This commit adds OPENTHREAD_PLATFORM_CSL_UNCERToption to Kconfig.
This option will allow user to configure openthreads CSL clock
uncertianity during build time.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Rename a few CAN API functions for clarity and consistency with other
Zephyr RTOS APIs.
CAN_DEFINE_MSGQ() becomes CAN_MSGQ_DEFINE() to match K_MSGQ_DEFINE().
can_attach_isr() becomes can_add_rx_filter() since a filter callback
function is not an interrupt service routine (although it is called in
isr context). The word "attach" is replaced with "add" since filters are
added, not attached. This matches the terminology used is other Zephyr
APIs better.
can_detach() becomes can_remove_rx_filter() to pair with
can_add_rx_filter().
can_attach_msgq() becomes can_add_rx_filter_msgq() and documentation is
updated to mention its relationship with can_add_rx_filter().
can_register_state_change_isr() becomes can_set_state_change_callback()
since a state change callback function is not an interrupt service
routine (although it is called in isr context). The word "register" is
replaced with "set" since only one state change callback can be in
place.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Change the can_tx_callback_t function signature to use an "int" (not an
uint32_t) for representing transmission errors.
The "error" callback function parameter is functionally equivalent to
the return value from can_send() and thus needs to use the same data
type and needs to be able to hold negative errno values.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
When support for custom MRU/MTU was added with
CONFIG_NET_L2_PPP_OPTION_MRU=y, code flow with
CONFIG_NET_L2_PPP_OPTION_MRU=n has been broken due to lack of valid
'ctx->lcp.my_options.mru' initialization and its use (with value 0) in
the implementation.
Initialize 'ctx->lcp.my_options.mru' unconditionally in lcp_init(), so
that PPP works fine with CONFIG_NET_L2_PPP_OPTION_MRU=n.
Fixes: 8a51a79d89 ("net: l2: ppp: possibility to have a custom
MRU/MTU")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Deprecate the use of CAN-specific error return values and replace them
with standard errno values.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit adds an option to store OpenThread settings in RAM for the
case where the flash driver is not available. This can be useful
for testing openthread on new platforms which are still under
development.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
The comment before this change was misleading, as those functions
(and other ones used from the level of user space application) require
DSA interface (like lan{012}), not the master one (like eth0).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The address of DSA API functions' structure available for usage from
the level of user's application (like for example in
samples/net/dsa/src) is stored in dsa context, not per DSA interface
device.
The struct dsa_context is defined once for all DSA (i.e. not master)
interfaces.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
`struct ieee802154_mpdu` access generates warnings related to unaligned
access to packed structure member. The structure itself however does not
need to be packed, since it is not mapped directly into the frame
buffer, but rather contains pointers to the structures representing
corresponding header regions in the frame. Those structures are
correctly defined as packed.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Replace unpacked in6_addr structures with raw buffers in net_ipv6_hdr
struct, to prevent compiler warnings about unaligned access.
Remove __packed parameter from `struct net_6lo_context` since the
structure isn't really serialized.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Replace unpacked in_addr structures with raw buffers in net_ipv4_hdr
struct, to prevent compiler warnings about unaligned access.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Replace unpacked in_addr/in6_addr structures with raw buffers in
net_arp_hdr struct, to prevent compiler warnings about unaligned
access.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Replace the statically defined net_buf with the standard mechanism of
allocating the buffer from a pool. This introduces a minor memory
overhead, but has the benefit of ensuring that standard net_buf calls
will work correctly.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Define a custom IEEE802154 based L2. The user can then use those symbols
to implement their own 802.15.4 based L2, based on those symbols, w/o a
need to modify the Zephyr tree.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Introduce a common config for all 802.15.4 based L2 implementations.
This way, any custom 15.4 L2 implementation will be able to
automatically enable use 15.4 driver, w/o a need to modify the actual
Kconfig.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
`net_eth_vlan_enable()` allowed to use illegal vlan tag values, fix this
by disallowing any tag value higher or equal to 0xfff (which is a limit
for the tag and a reserved value).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Reading a set MTU from the used net_if when starting LCP.
This enables also other custom MTU/MRU to be set for the link than
the default CONFIG_NET_PPP_MTU_MRU (set by a ppp driver during
initialization).
Signed-off-by: Jani Hirsimäki <jani.hirsimaki@nordicsemi.no>
The print specifier for `atomic_t` should be updated
to `%ld`, `%lu`, or `%lx` to account for the type
change of `atomic_t` to `long`.
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
There was a problem with source address selection for ARP
retransmissions, when an ARP entry was already pending. In such case,
the `entry` value passed to `arp_prepare()` is NULL, which in result
caused the `current_ip` variable being used as the source value. The
problem with this approach is, that the `current_ip` is only set in
IPv4 autoconf, the Ethernet L2 does not set this variable. In result,
every retransmission of an ARP packet was sent with unspecified source
address, preventing the response from being handled.
Fix this by partially restoring the behaviour of the ARP source address
assignment from before IPv4 autoconf was introduced. If the ARP is sent
by the IPv4 autoconf, use the `current_ip` value provided. If entry is
not set, use the source IPv4 address set in the actual data packet.
Otherwise, search for a source address on the interface corresponding to
the `entry`.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
- Add a `log_strdup` to the role text output for logging V1
compatibility
- Fix style issues
- Change where the documentation refers to an OpenThread device as
"himself" to "itself"
Signed-off-by: Chris Pearson <ctpearson@gmail.com>
If CONFIG_NET_LOG=y is set, OpenThread will output the current OT
role whenever the state changes.
To simplify understanding of the log output, this change replaces
the numerical role ID with the text name of the role. This also
required a change to a documentation file to replace an instance
of a numerical ID.
NOTE: This is potentially a breaking change should anyone be using
test scripts that monitor the OpenThread state changes and look
for the numerical ID. This does not seem to be the case for the
Zephyr tests, however.
Signed-off-by: Chris Pearson <ctpearson@gmail.com>
With the introduction of `EXPERIMENTAL` and `WARN_EXPERIMENTAL` in
Zephyr all subsys/net and drivers/ethernet/Kconfig.e1000 settings
having `[EXPERIMENTAL]` in their prompt has has been updated to include
`select EXPERIMENTAL` so that developers can enable warnings when
experimental features are enabled.
The following settings has EXPERIMENTAL removed as they are considered
mature:
- NET_OFFLOAD
- NET_PROMISCUOUS_MODE
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
With the introduction of `EXPERIMENTAL` and `WARN_EXPERIMENTAL` in
Zephyr all subsys/canbus, subsys/net/l2/canbus, and drivers/can settings
having `[EXPERIMENTAL]` in their prompt has has been updated to include
`select EXPERIMENTAL` so that developers can enable warnings when
experimental features are enabled.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
OpenThread has lately got an option to provide a custom
crypto backend that replaces the default, based on mbedTLS
API. Implement a backend based on ARM PSA crypto API that
is better suited for applications willing to take advantage
of the ARM trust zone technology.
Add Kconfig option: OPENTHREAD_CRYPTO_PSA_ENABLE which
enables that backend.
Also, another Kconfig option:
OPENTHREAD_PLATFORM_KEY_REFERENCES_ENABLE, implied by the
former, which enables usage of key references instead of
literal keys in OpenThread. It will eventually allow
OpenThread applications to keep sensitive data such as
encryption keys in the secure storage, accessible from the
secure world only.
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
Fixes#38994, ARP messages were being sent to IPvXmcast MAC addresses
rather than the expected source MAC address or the broadcast address.
Signed-off-by: Robert Melchers <rmelch@hotmail.com>
As per #38352, we would like to start building out PTP (IEEE 1588)
support for superset of gPTP functionality in Zephyr. This is the first
step to abstract away some key interfaces from NET_GPTP umbrella to
NET_L2_PTP.
Signed-off-by: Alex Sergeev <asergeev@carbonrobotics.com>
Refactor IPv4 multicast address to MAC multicast address conversion
into its own function, so it can be reused by drivers as it is already
possible for IPv6 multicast addresses.
Signed-off-by: Markus Fuchs <markus.fuchs@ch.sauter-bc.com>
BT_SECURITY_LOW and etc. were previously renamed and are no longer
valid.
The original rename is in the following commits:
1c48757d94 (New names, deprecate old)
5f2a9ba8e4 (Remove deprecated names)
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemiconductor.no>
Rework NCP interface configuration and NCP sample. Remove
CONFIG_OPENTHREAD_COPROCESSOR_SPINEL_ON_UART_DEV_NAME and
CONFIG_OPENTHREAD_COPROCESSOR_SPINEL_ON_UART_ACM Kconfig
options in favor of chosen node zephyr,ot-uart usage.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Checks PAN ID for matching self address / broadcast, then the short /
extended address based on the used address mode.
Only when IEEE802154_HW_FILTER is not advertised by driver.
Signed-off-by: Stancu Florin <niflostancu@gmail.com>
Instead of putting object files inside libzephyr.a,
simply build a separate static library as most other
driver types are doing this already.
Note that the include to subsys has been moved from
under the drivers into subsys, as it is actually
the subsystem's job to make sure the include
directories are correct.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This migrates all the current iterable section usages to the external
API, dropping the "Z_" prefix:
Z_ITERABLE_SECTION_ROM
Z_ITERABLE_SECTION_ROM_GC_ALLOWED
Z_ITERABLE_SECTION_RAM
Z_ITERABLE_SECTION_RAM_GC_ALLOWED
Z_STRUCT_SECTION_ITERABLE
Z_STRUCT_SECTION_ITERABLE_ALTERNATE
Z_STRUCT_SECTION_FOREACH
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Change DSA API to use `net_if` directly to make API calls instead of
indirectly via `dsa_context` and `switch_id`.
Remove unused `switch_id`, `switch_enable_port`, and `dsa_get_context`.
Signed-off-by: Arvin Farahmand <arvinf@ip-logix.com>
This provides a command line interface to query and modify
bridge instances, similar to Linux's brctl utility.
It can be used to inspect an application's bridge usage,
or manage a bridge of its own in a generic way.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
This adds the ability to create Ethernet bridges for connecting
separate Ethernet segments together to appear as a single
Ethernet network.
This mimics the Linux functionality of the same name.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
The openthread has enhanced features for periodic parent search,
this commit adds kconfig options to enable and configure these.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
6lowpan module can swap the original buffer with a newly allocated one
during decompression in case the decompressed header would not fit into
the original buffer. Therefore, storing the LL address offset and
restoring the pointer after decompression as it is done today is not
correct, as the new packet with decompressed IPv6 header will not
contain the LL header.
As the 6lowpan module doesn't deallocate the original buffer and
doesn't overwrite the LL header, its fine to use the original
pointers as they are.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Regular OpenThread upmerge to bring in a fix for a possible
infinite loop and support for DNS service subtypes.
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
Direct openthread API usage requires explicit locking,
which is also used internally.
Exposing a work queue through the openthread context allows
work to be submitted without the need to block other threads.
In particular with CONFIG_OPENTHREAD_MANUAL_START, application
logic can offload work which otherwise would need to wait for
the lock to become available.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
The openthread initialization in turn calls platform specific
functions, lock the API during this step.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Allow caller to either set or receive various Ethernet Qbu
configuration options defined in IEEE Std 802.1Qbu-2016
specification.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Allow caller to either set or receive various Ethernet Qbv
configuration options defined in IEEE Std 802.1Qbv-2015
specification.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If radio driver supports transmission security we need an option
to disable transmission security which by default is done by OT stack
for Thread v1.2
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
SRP client and server require ECDSA to be enabled otherwise the build
fails. Select OPENTHREAD_ECDSA for both OPENTHREAD_SRP_CLIENT and
OPENTHREAD_SRP_SERVER options.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
OPENTHREAD_SRP_CLIENT and OPENTHREAD_SRP_SERVER are Thread features and
not Thread configuration, so move them to Kconfig.features.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The OPENTHREAD_MAX_CHILDREN and OPENTHREAD_MAX_IP_ADDR_PER_CHILD options
make not sense for a MTD device. Make them depend on OPENTHREAD_FTD.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
With the updates to mbedTLS Kconfig it is now possible to update the
OpenThread security configurations by disabling the mbedTLS prompt and
avoid stuck symbol selection.
As part of this, the OpenThread security selection has been reworked
into a choice which ensures only a single security selection can be
chosen.
And the OPENTHREAD_MBEDTLS itself has been made promptless to ensure
other parts of the build system can select a specific OpenThread
security implementation and disable user selection, if the module or
sample require such behavior.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
With the updates to mbedTLS Kconfig it is now possible to update the
OpenThread security configurations by disabling the mbedTLS prompt and
avoid stuck symbol selection.
As part of this, the OpenThread security selection has been reworked
into a choice which ensures only a single security selection can be
chosen.
And the OPENTHREAD_MBEDTLS itself has been made promptless to ensure
other parts of the build system can select a specific OpenThread
security implementation and disable user selection, if the module or
sample require such behavior.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Following commits will remove k_work from net_pkt, so convert
PPP L2 to use k_fifo when sending PPP data.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Following commits will remove k_work from net_pkt, so convert
6locan L2 to use k_fifo between application and TX thread, and
driver and RX error handler.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit implements the OpenThread APIs to configure Enhanced-ACK
Based Probing in radio for a specific Initiator. This is needed for
Link Metrics functionality.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
OpenThread modified its NCP API, so we need to align with these changes
in Zephyr.
One of the major changes was removal of UART from the platform APIs.
`openthread/platform/uart.h` header file was moved to
`examples/platforms/util/uart.h` so we need to use the new location in
Zephyr. This means that OpenThread no longer impose the UART API but for
the simplicity of the upmerge I've kept the UART APIs as they are for
now.
The NCP initialization function have now to register a send handler,
and the appropriate transport driver have to call NCP callbacks when
transmission/reception is done. For now, re-use the existing code of
the UART driver, just as the upstream NCP application does.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This PR increases the OpenThread stacks to compensate
for the runtime increase of the MPU stack guard
when the usage of the FP context is detected.
Signed-off-by: Piotr Szkotak <piotr.szkotak@nordicsemi.no>
Use recently introduced API, which takes care of gracefully closing any
pending DNS requests and replacing existing DNS server list with new
one.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This aligns the error handling of send function to never unref the
buffer in place so the caller retain the ownership of the buffer
whenever there is an error.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The virtual_iface is already NULL checked by net_if_get_by_iface()
at the beginning of the function so no need to do it here too.
Coverity-CID: 220535
Fixes#34006
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Simplifying the loop in order to remove dead code (ctx_up is
always NULL after the slist loop.
Coverity-CID: 220538
Fixes#34003
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Logging v2 is using _Generic keyword for detecting type of
log message arguments. Apparently, it does not support handling
of pointers to forward declared structures. Added casting to void *.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Replace all existing deprecated API with the recommended alternative.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create net_l2_send() function which will be called by each L2
sending function so that we can catch all the network packets
that are being sent. Some L2 layers send things a bit differently,
so in those cases call the net_capture_send() directly by the L2
layer.
Add network packet capture call in receive side after the pkt has
been received by the RX queue handler. This avoids calling the
net_capture_send() from ISR context.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add infrastructure to allow user to configure the system so that
all the network packets, that are sent to or received from a specific
network interface, are sent to remote system for analysis.
The captured network packets are placed as a payload in UDP packet,
which is then sent inside a tunnel to a remote host. The host can
then receive the packets and for example show them in wireshark.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IPIP tunnel capability bit helps to detect which network
interface supports IPIP tunneling.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Introducing PPP dialup features to enable e.g. usage of nrf9160
based board as a dialup modem for transferring ip data over PPP
(e.g. windows dial up), i.e. usage of Zephyr PPP as a server for
providing MTU/MRU, IP address and DNS addresses for a PC:
- PPP LCP MRU option (configurable)
- PPP server: IPCP ip and dns address peer options to enable
providing IP and DNS addresses for PPP peer.
Signed-off-by: Jani Hirsimäki <jani.hirsimaki@nordicsemi.no>
This can be used to implement tunneling, VPN etc. The virtual
interfaces can be chained together to support multilayer
network interfaces.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move ptp_clock.h out of the top level include/ dir into
include/drivers/ptp_clock.h and deprecated the old location.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
net_eth_carrier_on() and net_eth_carrier_off() call k_work_init() on
work item that can be pending or still be processed in another thread.
This results in undefined behavior.
Initialize work item once and use an atomic flag to switch between
up/down carrier state. Submit work to workqueue whenever up/down carrier
state changes, so that last state is always properly propagated to
network interface layer.
While at it, save network interface pointer during ethernet context
initialization, so that is becomes static (and thread-safe) during whole
ethernet context lifetime.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
net_ppp_carrier_on() and net_ppp_carrier_off() call k_work_init() on
work item that can be pending or still be processed in another thread.
This results in undefined behavior.
Initialize work item once and use an atomic flag to switch between
up/down carrier state. Submit work to workqueue whenever up/down carrier
state changes, so that last state is always properly propagated to
network interface layer.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
When using `OPENTHREAD_ECDSA` deterministic variant has to be
enabled after some OpenThread changes. Also generic public key
functions are required.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Currently there is no way to distinguish between a caller
explicitly asking for a semaphore with a limit that
happens to be `UINT_MAX` and a semaphore that just
has a limit "as large as possible".
Add `K_SEM_MAX_LIMIT`, currently defined to `UINT_MAX`, and akin
to `K_FOREVER` versus just passing some very large wait time.
In addition, the `k_sem_*` APIs were type-confused, where
the internal data structure was `uint32_t`, but the APIs took
and returned `unsigned int`. This changes the underlying data
structure to also use `unsigned int`, as changing the APIs
would be a (potentially) breaking change.
These changes are backwards-compatible, but it is strongly suggested
to take a quick scan for `k_sem_init` and `K_SEM_DEFINE` calls with
`UINT_MAX` (or `UINT32_MAX`) and replace them with `K_SEM_MAX_LIMIT`
where appropriate.
Signed-off-by: James Harris <james.harris@intel.com>
This lets an application detect when a PPP connection fails to establish
or terminates, so that the connection can be reattempted (for example,
by setting carrier off and on).
Signed-off-by: Jim Paris <jim@jim.sh>
* Added implementations of otPlatCAlloc and otPlatFree methods
necessary for the OpenThread in case of using EXTERNAL_HEAP.
* Added CONFIG_OPENTHREAD_DNSSD_SERVER option to allow enabling
OT_DNSS_SERVER feature.
Signed-off-by: Kamil Kasperczyk <kamil.kasperczyk@nordicsemi.no>
Remove `OPENTHREAD_CONFIG_NCP_BUFFER_SIZE` define since it does not
exist in OpenThread.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Bogus fragmented packet could be sent without a FRAG1 fragment and hit
reassembly. Let's make sure this does not happen.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In case the current packet is the same as the cached one, let's not
unreference it while clearing the cache.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Though ACK frames are not meant to reach L2 (drivers must ensure this
never happens), let's "re-enforce" the L2 by dropping them.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
All addressing mode but IEEE802154_ADDR_MODE_NONE should have a valid
address. If not, the frame is invalid.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
After the latest upmerge, OpenThread requires explicit configuration
of the Master Key. This commit adds a Kconfig symbol that can be
used to setup its value. By default no Master Key is configured and
OpenThread generates a random one.
The Sockets Echo samples are configured with a fixed key with this
commit.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
6lowpan over BLE should work without solicit node multicast messages
according to RFC7668[1], but that requires Neighbor Solicitation with
Address Registration Option, which is currently not implemented in
either Zephyr or Linux. This is causing the router to fallback to normal
neighbor solicitation based discovery, but the NS frames are being
discarded in the host stack because the solicit node multicast groups
are not registered.
This drops the NET_L2_MULTICAST_SKIP_JOIN_SOLICIT_NODE as a workaround
and adds a TODO about it.
[1] https://tools.ietf.org/html/rfc7668#section-3.2.3
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Modifies openthread shim layer to automatically join multicast
addresses as they are added to zephyr from openthread, unless the
address is interface-local or link-local. This allows incoming
openthread multicast group messages to avoid being filtered by
zephyr ipv6 recv.
Fixes#31085
Signed-off-by: Joel Frazier <frazieje@gmail.com>
Convert drivers to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit replaces the 'select SHELL' statement with
'depends on SHELL' in OPENTHREAD_SHELL config option.
This ensures, that shell will not be implicitly enabled
when OpenThread stack is built.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Reordering of the struct elements to match the Linux format.
The __packed() is not necessary anymore.
std_id and ext_id is merged to id in the frame and filter.
Additionally, the frames are ready for CAN-FD.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Add option to enable software CSMA backoff in the OpenThread MAC layer.
This allows to run CSMA procedure correctly in radios that do not
support hardware CSMA backoff, and use them as RCP, where this feature
is required.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
If networking pre-emptive thread priorities are enabled,
then use the proper macro to enable them.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
* Add RCP library.
* Conditionally remove non required libraries not required for RCP.
* Drop :option: marker for CONFIG_OPENTHREAD_NCP_SPINEL_ON_UART_ACM
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
subpress warnings from llvm:
warning: absolute value function 'abs' given an argument of type
'int64_t' (aka 'long long') but has parameter of type 'int' which may
cause truncation of value [-Wabsolute-value]
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit corrects the maximum allowed amount of children to
match Thread specification.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Existing openthread_api_mutex_lock()/unlock() functions are
crucial to assure thread safety of an application which
needs to use OT API directly, but some applications may also
require a non-blocking version of the former for less critical
OT-related tasks.
Add openthread_api_mutex_try_lock() which never waits and
exits immediately if the mutex is held by another thread.
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
If an address was obtained by IPCP, it should always be removed in
ipcp_down(). This commit replaces the predicate with something slightly
more robust.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
This commit moves IPv6 initialization from OT init to OT start to
avoid unwantedly bringing 802.15.4 radio up.
Previously, even when OT manual start was enabled, the radio would
be receiving frames resulting in unnecessary power consumption and
causing issues for instance when the device just wants to use
Bluetooth for provisioning befor moving to Thread.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Another team reported that current default values for number of allowed
IP addresses per child (4) and and max number of children (10) are too
small for some customers.
Increased the values allowed configuring child count.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
Without removing the stale address obtained during IPCP, it will still
be present the next time we do IPCP, marked as "in use" by the network
stack even if it is stale. This turned out to be a showstopper for
restarting the PPP stack on devices without static IP.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
This commit adds additional Kconfigs that allow for changing
configuration values for the Zephyr port in OpenThread.
Those values are:
- number of the internal OT message buffers
- number of the state change callbacks
- number of the EID-to-RLOC cache entries
- size of the NCP buffer
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Instead of directly checking the multicast IPv4 address, use
the net_ipv4_is_addr_mcast() utility function.
Fixes#26584
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove obsolete include of the shell_uart.h file.
It is sufficient to include the shell.h file.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordisemi.no>
Since commit b3a1ede830 OpenThread uses the Zepyhr settings submodule
instead of writing to the flash directly. The flash.c file is not
compiled anymore, so let's just remove it. Also remove the
OT_PLAT_FLASH_PAGES_COUNT Kconfig option which was solely used by that
file.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Check that Ethernet header is in the first net_buf fragment.
This is very unlikely to happen as device driver is expected
to only deliver proper Ethernet frames to upper stack.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fixed stack being to small for joiner operations.
Enabled auto joining even in case of manual start.
Fixed attachement of SED on norfic radios.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Instead of hardcoding the priority1 and priority2 values used
in BMCA, let the user tweak the values via Kconfig.
Fixes#28151
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix the OpenThread initialization to prevent the IPv6 interface to
be enabled when `CONFIG_OPENTHREAD_RAW` is set.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Some implementation consist of multiple libraries to be linked instead
of one. Added possibility to pass multiple libraries. Additionally
renamed the config name as it was stateing something different than it
does.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Allow user to create SOCK_DGRAM type AF_PACKET socket. This
allows user to send raw IP packets without specifying
L2 (like Ethernet) headers.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The steps_removed field must be placed right after root_system_id
so that priority vector comparision can be done in one memcmp()
call. This fixes the best master clock selection algorithm (BMCA).
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
-Wimplicit-fallthrough=2 requires a fallthrough comment or a compiler
to tells gcc that this happens intentionally.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
PPP Phase Diagram [1] allows only one way phase change. In current
implementation there is an additional RUNNING phase, which is entered
just after NETWORK phase.
Prevent going back from RUNNING to NETWORK phase when Term-Req was
received, as this is meaningless for overall PPP operation and violates
PPP Phase Diagram property of having one way direction change.
This change also improves Adminitrative Close handling (calling
lcp_close()). This request results in moving into TERMINATE phase. Then
LCP is put down (by calling lcp_down()) and then ppp_link_down() is
called, which so far (before this patch) resulted in moving back to
NETWORK and then to DEAD. Right now (after this patch) we move directly
from TERMINATE to DEAD phase, which is exactly how [1] specifies it.
[1] https://tools.ietf.org/html/rfc1661#section-3.2
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
State Transition Table [1] specifies that Administrative Close should
result in CLOSING state. This is not respected in case of LCP, as
STOPPED state was forced in lcp_close().
Don't force going into STOPPED state in lcp_close() and rely on
ppp_fsm_close() to move to CLOSING state instead.
This patch fixes overall Adminitrative Close procedure and allows to
move back into fully operating PPP connection once again after
Adminitrative Open.
[1] https://tools.ietf.org/html/rfc1661#section-4.1
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Save some memory and separate common string snippets from larger
strings. In this case "does not match" sub-string is printed by
several warning prints so separate the sub-string from the bigger
string.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch implements optional authentication phase, which is done
between link establishment and network phases. It is part of LCP option
negotiation to decide whether authentication is needed and which
protocol will be used. For now we add only PAP support and try to
negotiate it when some other protocol (e.g. CHAP or EAP) is proposed
earlier. For simplicity reason we only add one way authentication
support, which means that we try to authenticate to the other peer, but
do not require authentication from it.
This is an important step to make PPP work with cellular network modems,
because most of them require to provide username and password within PPP
authentication phase. Those credentials are used by modem to login to
cellular network. In most cases however it is enough to provide dummy
values, because they are not verified. For this reason and simplicity of
this patch we hardcode PAP Peer-ID and Password now.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This module had only some header includes, without actual code. Remove
it, as it is better to create one module per authentication protocol
anyway.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add enums of PAP, CHAP and EAP authentication protocols. Also add their
string representations, so they will nicely show up in logs during
debugging.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Interpret -EINVAL return value from options' parse() callback as "option
value is not supported". After receiving such value nack() callback will
be executed in order to put supported value in the response.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This macro has no use in code and was most probably replaced by
FSM_TIMEOUT (which resolves to CONFIG_NET_L2_PPP_TIMEOUT) with the same
default value.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Those macros are not used anymore after commit 35a2519091 ("net: l2:
ppp: add generic function for handling Conf-Req"), because we no longer
need preallocated table on stack for parsing option information.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This option is not used after commit 50b2cafc42 ("net: l2: ppp: use
net_pkt API for replying to Configure-Req") has been applied. We don't
need to preallocate table on stack for parsing option information, so
information about maximum number of supported options is useless.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Drop unused ppp_parse_options_array() function and 'struct
ppp_option_pkt' data type. Both were used in initial PPP implementation,
but are not longer needed after recent PPP refactoring.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Introduce new ppp_config_info_req() function that can be used in order
to handle options received within Conf-Req packet. As an input it takes
array of supported options. If received Conf-Req packet contains unknown
options, then a Conf-Rej packet is automatically generated with all of
those options. If all of received options are supported, then function
continues to parse each provided option individually by calling option
specific callbacks.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Use a generic handler for received options in Conf-Rej packet. This will
mark all those options as rejected, to they will no longer be included
in subsequence Conf-Req packets.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Use a generic handler for received options in Conf-Rej packet. This will
mark all those options as rejected, to they will no longer be included
in subsequence Conf-Req packets.
This allows to communicate with PPP peers, which do not support DNS1 and
DNS2 options.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far there was no generalized way how to handle negotiation of "my
options" (those sent with Conf-Req packet to peer). Peer response for
proposed options and their values were not tracked in any way, so
rejected (by peer) options were sent over and over again in subsequent
Conf-Req packets. In case of IPCP it means that all sent options such as
IP_ADDRESS, DNS1, DNS2 were mandatory for being supported by peer in
order to successfully finish negotiation. For example if 'pppd' was the
configured peer (e.g. when using with QEMU and net-tools scripts),
without ms-dns being configured (which is the default), then "my
options" negotiation failed.
Introduce generalized mechanism for negotiating "my options", so it is
easier to maintain current set of supported options and easily add new
options to the implementation in future. FSM instance inititialization
function can provide information about supported "my options".
Information is is passed as a table of 'struct ppp_my_option_info'
containing:
* option code (type),
* callback for adding option to Conf-Req packet,
* callback for received Conf-Ack with that option,
* callback for received Conf-Nak with that option.
Store also runtime information about each negotiated option. First of
all remember which options have been rejected, so they are not sent to
peer once again in the next Conf-Req packet. This will solve issue with
IPCP negotiation when peer doesn't support DNS1 or DNS2 options. Keep
also track about which options have been acked, so such information can
be verified before bringing FSM instance up.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Rework implementation of ppp_parse_options() to be more generic and
flexible to use. Pass callback and user data for parsing each option
separately.
Keep old functionality of ppp_parse_options() accessible via
ppp_parse_options_array() function. This will make sure that old code
using this function doesn't need to be changed now. There are plans
however to remove ppp_parse_options_array() once there are no more users
of it in future.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Use net_pkt API to assemble Configure-Req messages. Compared to net_buf
API it allows us to simplify code.
Remove append_to_buf() helper functions, as their functionality is now
totally replaced by net_pkt API. Additionally net_pkt API handles data
that wraps several net_buf packets, which was not the case with
append_to_buf().
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Use net_pkt instead of net_buf API for replying to Configure-Req. We use
the fact that for now we reply with either Configure-Ack or
Configure-Rej only. In both cases we can allocate net_pkt ahead, because
we know its maximum length (which is equal to length of received
Configure-Req packet).
Make also an improvement in generic FSM code and reply with
Configure-Rej to all Configure-Req for which there is no config_info_req
callback set. Use that to drop LCP specific Conf-Req handling code,
because there is no option properly supported there yet.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far ppp_parse_options() has returned enum net_verdict. This type was
never used directly by network stack. Instead, caller was always
checking for NET_OK and returning error code in case of failure.
Change implementation of ppp_parse_options(), so it returns error code
in case of error and 0 when succeeded. This better fits its generic
purpose.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There is no allocation in ppp_l2.c file, which mean that
BUF_ALLOC_TIMEOUT macros is not used anywhere. Drop it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There was a race condition when ppp_fsm_open() was called in CLOSED
state. Conf-Req was sent first, then state was changed to
REQUEST_SENT. In the meantime however we have already received Conf-Req
to which we responded with Term-Ack.
Change state before sending Conf-Req, so we handle Conf-Req from peer
properly instead of dropping it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
OpenThread API is not thread safe, therefore it shall be protected
from being preempted by OT thread, or other thread issuing API calls.
The problem showed up after a recent OpenThread upmerge, where changes
in the Joiner class made this problem visible. W/o extra protection,
`otJoinerStart` call can be preempted by the OT thread, leading to an
unexpected behavior.
Introduce new function to allow to lock any API operations for others.
Anyone willing to call OT APIs, shall lock the mutex first to get
exclusive access to the stack.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
`otLinkRawSetEnable` was removed and Link Raw mode is now enabled with
`otLinkRawSetReceiveDone` which requires to register a callback
function. Since it makes little sense for OT L2 to register a Link Raw
callback in current setup, leave it up to the application to register
the callback.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
is_init field is useless, because there is only single code path that
always sets it to true before using it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Make sure IPv6 address is removed from network interface in IPV6CP
protocol down handler. This makes sure that application can receive
high-level notification about missing network connection.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Make sure IPv4 address is removed from network interface in IPCP
protocol down handler. This makes sure that application can receive
high-level notification about missing network connection.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Added the 'fall through' comment to switch to quiet compiler
and coverity warnings.
Fixes#25724Fixes#25726
Signed-off-by: David Leach <david.leach@nxp.com>
To allow hardware crypto acceleration custom mbedtls library needs to be
prepared. However current implementation forces the default library to
be used.
This patch allows not using the default library and passing custom
mbedtls target to use with openthread.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
The Z_STRUCT_SECTION_ITERABLE() provides an alignment so remove
the 32 byte alignment for net_if and ppp_protocol_handler structs.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use system provided Z_STRUCT_SECTION_FOREACH() and
Z_STRUCT_SECTION_ITERABLE() macros instead of manually coding
everything for network sections.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Different switch was used for build to allow including all shim body
in zephyr without the need for building openthread from this repo. This
allows developer to include custom OpenThread sources as part of the
application.
This change is needed as Thread is a subject of certification and
sources provided by zephyr may not necesairly pass certification or be
precertified. User is allowed to use certified OpenThread version
this way.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
When this happens, ip6_addr_cb and ipv6_addr_event_handler() both look
unused, since they are passed to macros which discard them.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Single work object for whole fsm was not being able to handle more than
single packet at a time. Because of that we have overwritten already
scheduled packets, resulting in fsm timeout and net_pkt leak.
Use net_pkt work object instead, so we can safely schedule more than a
single packet.
This commit also drops workaround for qemu_x86 unit testing.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Currently there is a single function that handles both Configure-Ack and
Configure-Rej messages. This is obviously wrong for Configure-Rej,
because implementation applies options received in the message.
Remove Configure-Rej callback, so those frames are simply ignored for
the time no valid handling code exists.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Clear negotiated options in protocol down handler. That way all
addresses are properly requested (by sending 0.0.0.0 in Configure-Req)
in the subsequent option negotiation phases.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Unit tests were failing to build because random header was included by
kernel_includes.h. The problem is that rand32.h includes a generated
file that is either not generated or not included when building unit
tests. Also, it is better to limit the scope of this file to where it is
used.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
There is already a variable 'network_protos_up', which stores number of
network protocols being up. Additionally each network protocol has its
own state represented by is_ip{,v6}cp_up. Use the latter in FSM up() and
down() callbacks.
This fixes a case when both IPCP and IPv6CP protocols are going
down. When using ctx->is_network_up only one of them (the first) was
deinitialized correctly, second stayed always up (at least partially,
e.g. not calling ppp_network_down()).
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Each PPP packet sent on wire needs to have at least 4 bytes length. Set
that length for outgoing Term-Req and Term-Ack packets. Also update
length validation to check for at least 4 bytes instead of at least 1
byte.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
It fixes #issues/26220.
openthread_start function is called when L2 enable(iface, true) is
called. openthread_stop is called when L2 enable(iface, false) is
called. openthread_stop makes the device to leave the OpenThread
network.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
OpenThread BR can assign addresses via DHCPv6 or when acting as an
NCP, addresses can be added manually. Currently, those addresses are
handled in the same way as auto-configured addresses.
This patch maps the newly introduced mAddressOrigin of otNetifAddress to
Zephyr's net_addr_type.
This way an application can register a handler and differentiate by type
of assignment:
```
static void handler(struct net_mgmt_event_callback *cb,
u32_t mgmt_event,
struct net_if *iface)
{
if (iface->config.ip.ipv6->unicast[i].addr_type == NET_ADDR_DHCP) {
}
}
```
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
Some options were available in the options.cmake but were not reflected
in Kconfig.
Added possibility to enable additional configuration options for OT.
Some of the options were left commented out as those options are not
yet supported e.g. require Thread 1.2 or require shim changes.
As openthread has gazillion configuration options that are passed as
define value, created generic option for passing any number of those
values separated with space.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
Currently user needs to specify quite much additional options to enable
OpenThread support. He also needs to set ip address count,
heap size, etc depending on features enabled.
Nade changes to automatically select/set some of the options on
enabling OpenThread
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
Both ASYNC_CTRL_CHAR_MAP and MAGIC_NUMBER are not supported right
now. Send Configure-Reject for them instead of Configure-Nak, as we
don't even propose new values in reply (which should be part of
Configure-Nak).
Send also Configure-Reject for MRU option, as we don't respect it
either.
Drop both count_rej and count_nack, as we can rely solely on nack_idx to
send Configure-Reject or not.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
The sync receive timeout was using invalid value (nanoseconds
instead of milliseconds). This caused unnecessary state switches
from SLAVE to MASTER and back.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add debug prints when the port announce information state
machine state changes. This is useful in debugging.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The port number is stored starting from 0 in Ethernet context.
But in gPTP, it is an index which starts from 1. So increase
the value by 1 for a value returned from Ethernet context.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It may be useful for the application to register its own callback for
ot state changed event which does not override the current one.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
It may be useful to start openthread manually but with default
network settings. For instance when the application wants to register
ot state changed callback which should be done before openthread
starts.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
OpenThread API is not thread-safe.
Moved creation of otMessage to the Thread task and created api
for passing it properly.
This way it should be less possible for an issue to occure eg.
during message buffer allocation.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
Avoid null pointer access by checking that Ethernet device has
PTP clock before trying to get the actual PTP clock device.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It add an option to configure openthread thread priority class
by the application if there is a such need.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
Net pkt is added into the ot net list after queued net pkt into
the net_rx which bases on it. It affects in losting net pkt when for
instance ot thread is preemptive.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
The eth_stats_update_errors_rx() implicitly assumes that passed pointer
to struct net_if is not NULL.
This is not true for MCUX's eth_rx() (in eth_mcux.c), where we can
execute eth_stats_update_errors_rx() after net_recv_data() returning
-EINVAL because of passed NULL iface pointer.
This change fixes this problem with adding extra check on iface not
being NULL before it is dereferenced.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Right now shell pointer is not assigned before doing a scan, so scan
results are printed using printk(). Save shell instance in context, so
results are printed using shell_fprintf(), thus better aligned in the
console output.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Some radio drivers need configuration before start-up. Up to now only
the RF2XX drivers allowed this, but other radio drivers need this as
well. In particular for setting EUI64 addresses.
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
Due to new checks in mbedTLS config sanitizer, TLS option can no longer
be left enabled, when TLS is not used. OpenThread needs MBEDTLS_MD_C
and MBEDTLS_CIPHER_C even without TLS being used, so we need an option
to enable them manually.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
OpenThread moved from 4 to 5 debug levels and it was not possible
to configure all of them with Kconfig.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
The LLDP packet was created but its type was not set to LLDP
and was sent as ARP message.
Fixes#25084
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add OpenThread configuration option, which allows to configure and start
OpenThread stack operation manually. This mode should be used in NCP
devices, as well as is needed for certification purposes, where
OpenTread stack have to be configured by the test framework and not
initialize and join the network on its own.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Frame format was validated, but its length should be also validated
relevantly against the format.
Fixes#24970
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert all canbus related API/samples/tests/subsys
to the new timeout API with k_timeout_t.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
There was no way to use Openthread CoAP api in zephyr application so
far. These changes enable the feature. Now you can fully use CoAP
communication in an application working in Thread network.
Signed-off-by: Lukasz Maciejonczyk <Lukasz.Maciejonczyk@nordicsemi.no>
Received frames shall be handled in the OpenThread thread, not in
the receiver thread.
Passed received frame to the function that will handle it in a proper
thread instead of calling otPlatRadioReceiveDone directly.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
In case hardware CSMA CA is used, ieee802154 L2 does not initialize ACK
processing structures, as it does not need to process ACK messages. As
it is not possible to conditionally disable ACK reporting to the upper
layer, ieee802154 could end up using uninitialized kernel primitive
(semaphore) in the ACK handler, which lead to a crash.
Avoid this, by explicitly checking in the ACK handler, if HW CSMA CA is
used.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Even though radio driver can report in its capabilities that it does
support CSMA CA, there's no way in the driver to select how the frame
should be transmitted (with CSMA or without). As layers above radio
driver (Thread, Zigbee) can expect that both TX modes are available, we
need to extend the API to allow either of these modes.
This commits extends the API `tx` function with an extra parameter,
`ieee802154_tx_mode`, which informs the driver how the packet should be
transmitted. Currently, the following modes are specified:
* direct (regular tx, no cca, just how it worked so far),
* CCA before transmission,
* CSMA CA before transmission,
* delayed TX,
* delayed TX with CCA
Assume that radios that reported CSMA CA capability transmit in CSMA CA
mode by default, all others will support direct mode.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
