- Add initial version of CYW920829M2EVK-02 board
- [drivers: clock_control] Make it possible to set up both iho and imo
clocks instead of just one or the other
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Removing dependency on cyhal in airoc wifi driver.
It need to build airoc wifi driver with different than
PSoC 6 Soc like STM32
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
When kernel stack is defined as an array, K_KERNEL_STACK_LEN()
is used to calculate the size for each stack in the array.
However, standalone kernel stack has its size calculated by
Z_KERNEL_STACK_SIZE_ADJUST() instead. Depending on the arch
alignment requirement, they may not be the same... which
could cause some confusions. So align them both to use
K_KERNEL_STACK_LEN().
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Added initial version of Infineon AIROC WIFI driver
Added initial version of binding file for Infineon AIROC WIFI
driver
Rename CONFIG_ABSTRACTION_RTOS_COMPONENT_ZEPHYR to
CONFIG_USE_INFINEON_ABSTRACTION_RTOS
Exclude cy8cproto_062_4343w platform from
drivers.modem.esp_at.build test
Change revision hal_infineon to
69c883d3bd9fac8a18dd8384624b8c472a68d06f
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Infineon CAT1 SDHC/SDIO driver
Added initial version of binding file for Infineon CAT1 SDHC/SDIO
driver
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
- Added initial version of Infineon CAT1 Flash driver
- Added binding file for infineon,cat1-flash-controller.yaml
- Added overlays for subsys/nvs and drivers/flash_shell
to support cy8cproto_063_ble, cy8cproto_062_4343w boards
- Defined erase-block-size in PSoC6 MPN dtsi.
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\cy8cproto_062_4343w board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
- Added Cmakefiles for modules\hal_infineon\btstack-integration\,
where handle generation of Bluetooth include blob from HCD binary.
- Supported following device/modules:
-- CYW43012/MURATA-1LV module
-- CYW4343W/MURATA-1DX module
-- CYW43439/MURATA-1YN module
-- CYW4373/STERLING-LWB5plus module
- Added possibility to use user provided BT Firmware HCD file via
kconfig (path must be defined in
CONFIG_CYW43XX_CUSTOM_FIRMWARE_HCD_BLOB)
- Updated top makefile
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Problem:
pull/43494 is causing the CMake warning
No SOURCES given to Zephyr library: modules_hal_infineon
modules_hal_infineon library was defined even if none of the
below subdirectories is added; so, when not building for
Infineon/Cypress devices, the source list for this library
will be empty.
Fix:
Added 'zephyr_library_named(modules_hal_infineon)' under condition
'if(CONFIG_HAS_XMCLIB OR CONFIG_SOC_FAMILY_PSOC6)'
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
