Support to set BSS parameter "max_num_sta" at compile and run time
Added support to configure `max_num_sta` BSS parameter.
Maximum number of stations allowed in station table. New stations will be
rejected after the station table is full.
Signed-off-by: Ajay Parida <ajay.parida@nordicsemi.no>
Support for configuration of AP parameter "Skip inactivity poll".
Only build time setting is supported.
Signed-off-by: Ajay Parida <ajay.parida@nordicsemi.no>
Support to set BSS parameter at compile and run time.
Added support to configure `max_inactivity` BSS parameter.
Station inactivity timeout is the period for which AP may keep a client
in associated state while there is no traffic from that particular client.
If a non-zero value is set, AP may choose to disassociate the
client after the timeout.
Signed-off-by: Ajay Parida <ajay.parida@nordicsemi.no>
When disconnect request is successful, the status
was taking as WIFI_REASON_DISCONN_UNSPECIFIED only.
Adding WIFI_REASON_DISCONN_SUCCESS which can be help
to determine status of disconnect request. If this status
is failed then reason can be useful.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
When the ops for PS parameters we removed and aggregated into a single
OP, the respective defines weren't cleaned up.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
There is no limitations for dwell time. Just add
valid condition for positive value. So , it's better
to remove those constraints.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
When there is 4 way handshake timeout, it can be because of
incorrect credential or some times when AP's signal strength
is weak. It can cause 4 way handshake fail. Adding comment
where WIFI_STATUS_CONN_WRONG_PASSWORD is defined.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
There should be a particular defines which clarify the
use of that number. So, replacing numbers with defines
in wifi shell.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
The shell is printing "connected" while passing
the wrong password to connect command. If the status
value is 0, then only shell will print "connected."
The wrong password will disconnect the connection
with an unspecified reason code.
If the default value of the unspecified disconnect
reason code is 0, then status will print "connected."
By changing the default value to WIFI_STATUS_CONN_LAST_STATUS,
it will print the correct reason, like a failed request
with reason code.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
There is no need to hide the wpa_supplicant interface
struct so add it directly to net_wifi_mgmt_offload struct.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add command to query to WiFi driver/firmware revision. The API is expected
to return the firmware revision and driver version as a string, and can be
used by the user to determine what revision of the WiFi driver is in use.
Signed-off-by: Sandip Dalvi <sandip.dalvi@nxp.com>
Provision of configurable parameter for generating unblock event
ahead of TWT slot. Host application depending upon latencies can
configure this to wakeup rpu ahead of the TWT slot.
Signed-off-by: Ajay Parida <ajay.parida@nordicsemi.no>
These are helpful to track clients being added and deleted.
Applications can actions based on these events.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
These events communicate the status of AP mode operations (enable or
disable) with few pre-defined enumerations.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
This can be used to interpret the "status" in the disconnect result event.
To start with a few common reasons are enumerated but can be extended in
the future.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
This can be used to interpret the "status" in the connect result event.
To start with a few common reasons are enumerated but can be extended in
the future.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
There shouldn't be any reason to be able to modify the passed psk,
and having this non-const gives application warnings if passing a
constant string.
Signed-off-by: Maciej Zagrabski <mzi@trackunit.com>
Update the storage type of the SSID strings to pointers to the strings,
instead of needing to copy the strings into the struct. This
substantially reduces the parameter struct size.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Turn the nested arrays of `scan_params->chan` into a single array.
This adds the requirement to specify the band for each channel, but
eliminates the large amount of dead memory for unused bands. Overall,
this saves 50% of the RAM space for this variable.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Make the maximum number of channels that can be manually scanned
configurable by the application. The previous value of 233 was vastly
overallocating memory as the largest band only contains 60 allocated
channels.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Zero length arrays are a GNUism not supported by all compilers. If
`zephyr/net/wifi_mgmt.h` is included by an application without WiFi
enabled, ensure array is at least one element long.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
All WiFi channel numbers fit within a 8 bit number, as the maximum
allocated channel is 233. This halves the memory requirement.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
This change brings in support for setting various Wi-Fi modes and
enables a specific Wi-Fi interface to be also placed into a sniffer
operation via monitor mode and promiscuous mode. A raw TX- packet
Injection mode is also introduced
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
wifi_utils_parse_scan_bands could cause a crash if a constant string is
passed to it. Fix this by duplicating the input string parameter before
parsing it with strtok_r.
Signed-off-by: Sachin D Kulkarni <sachin.kulkarni@nordicsemi.no>
The twt and ps helper functions were not namespaced (were missing
wifi_ prefix).
Also change wifi_get_twt_... to more logical wifi_twt_get...
like the other twt prefixed functions and wifi_get_ps... to
wifi_ps_get... like the other ps prefixed functions.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
net_iface_status is larger than scan_result, causing
net_iface events to be dropped due to info exceeding
NET_EVENT_INFO_MAX_SIZE.
Signed-off-by: Noah Luskey <LuskeyNoah@gmail.com>
Add scan extension to allow limiting the scanning to specific channels.
Only 20 MHz channel specifications are allowed presently.
Signed-off-by: Sachin D Kulkarni <sachin.kulkarni@nordicsemi.no>
Add scan extension to allow limiting the scan results to a user defined
maximum number. This parameter is intended to return results with the
best RSSI. It cannot be counted upon to limit the scan times since the
Wi-Fi chips might have to scan all the channels to find APs with the
best RSSI values across all channels.
Signed-off-by: Sachin D Kulkarni <sachin.kulkarni@nordicsemi.no>
Add scan extension to control scanning time spent on channels where
passive scanning is used.
Signed-off-by: Sachin D Kulkarni <sachin.kulkarni@nordicsemi.no>
Added scan extension to support scanning individual Wi-Fi bands or
combinations thereof.
Signed-off-by: Sachin D Kulkarni <sachin.kulkarni@nordicsemi.no>
Decouple interface and Wi-Fi APIs, Wi-Fi APIs are common independent of
Wi-Fi offload or implemented natively (This is preparation for
introducing Native Wi-Fi).
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Default scan mode is Active. User can force the scan mode to passive
through Kconfig option or using 'passive' option from shell.
Using either of this option will override regulatory settings and
forces all scan channels to be passive only.
Signed-off-by: Ajay Parida <ajay.parida@nordicsemi.no>
This is needed for applications that rely on WPA supplicant being
in disconnected state before issue subsequent commands (e.g., issue scan
immediately after disconnect fails, until disconnect is completed).
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
'ps_wakeup_mode' is used to set the wake up interval
to either 'dtim or 'listen_interval'. By default the
sta wakes up every dtim interval.
With 'ps_wakeup_mode' set to 'listen_interval' sta
will wake up for every listen interval period configured.
Signed-off-by: Ajay Parida <ajay.parida@nordicsemi.no>
