Remove `IEEE802154_SELECTIVE_TXPOWER` option.
Cache the tx power value in nRF5 driver and make use of it on each
operation.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
The RSSI value in net_pkt (net_pkt_cb_ieee802154.rssi) was used
inconsistently across drivers. Some drivers did cast a signed dBm value
directly to net_pkt's unsigned byte value. Others were assigning the
negative value of the signed dBm value and again others were offsetting
and stretching the signed dBm value linearly onto the full unsigned byte
range.
This change standardizes net_pkt's rssi attribute to represent RSSI on
the RX path as an unsigned integer ranging from 0 (–174 dBm) to 254 (80
dBm) and lets 255 represent an "unknown RSSI" (IEEE 802.15.4-2020,
section 6.16.2.8). On the TX path the rssi attribute will always be
zero. Out-of-range values will be truncated to max/min values.
The change also introduces conversion functions to and from signed dBm
values and introduces these consistently to all existing call sites. The
"unknown RSSI" value is represented as INT16_MIN in this case.
In some cases drivers had to be changed to calculate dBm values from
internal hardware specific representations.
The conversion functions are fully covered by unit tests.
Fixes: #58494
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The IEEE802154_2015 option is misleading, as it does not introduce full
802.15.4-2015 standard compliance but only random bits, plus it's
defined at the radio driver level, which brings yet another confusion.
Because of that, the option will be deprecated, and respective parts of
code that made use of it converted to use more specific configurations:
* nRF driver will now use CONFIG_NRF_802154_ENCRYPTION to specify
whether to compile in TX security
* net_pkt will only add extra 802.15.4 control block fields if
OpenThread is used, as they were solely used by this L2
* OpenThread radio layer will now use the OpenThread version to
determine whether to compile in TX security.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This change implements part two of the program laid out in the TSCH RFC,
see #50336#issuecomment-1250250154 :
> Consolidate IEEE 802.15.4 options in net_pkt
This change improves decoupling of generic net core code from
IEEE 802.15.4 internals. It also simplifies IEEE 802.15.4
attribute cloning and thereby makes it easier to maintain and less
error prone (and probably even faster as individual bits are no longer
copied over separately).
This enables us to extend and design IEEE 802.15.4 L2 attributes inside
the package in isolation from the net core code which will no longer
have to be changed when introducing changes or additions to the flags.
This flexibility will be built upon in later change sets to model the
IEEE 802.15.4 attributes closer to the spec.
The solution is inspired by Linux's sk_buff->cb attribute which addresses
the same concern as the attribute introduced in this change set:
https://elixir.bootlin.com/linux/v6.0.1/source/include/linux/skbuff.h#L871
As the inline comment says: The cb attribute can be made a union or even a
uint8[something] in the future, if further L2s need a control block, too.
Right now such full indirection would make the code overly abstract, so
I chose to compromise with maintainability in mind.
Care has been taken to ensure that this changes does not introduce
additional padding into the net package. To maintain zero-padding, future
changes to the net packet struct will have to ensure that the
IEEE 802.15.4 struct is 4-byte aligned (iff the IEEE 802.15.4 struct
continues with max uint32_t scalar members) which is no deviation from
the previous implementation.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
